Related
Hi,
First time : i'm sorry for my bad english,
I try a radio corrupt (not for my hermes-probably for 900). I would like change the corrupt radio. I try radio 1.16 but my hermes wait 30 minutes and my pc write "checking the information ..." and nothing.
In bootloader i can see :
Herm200
IPL.-1.01
and
Herm299
SPL-1.04
After change the first corrupt radio, I have a white screen and nothing .
I would like to put the original radio.
My Hermes is a SFR Wodafone 1605.
Thank you for you help
Sincerly,
YC
See "Problem 5: Device shows NO GSM when booting" on this wiki page:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
Re
Ok prof ! I'se a good article :
"If you feel brave, and always at your own risk, what you should do to fix your bricked hermes with screwed radio is this:
1) Put your Hermes in bootloader mode
2) Disable USB connections in ActiveSync
3) Open mtty.exe and select USB port, then connect.
4) Hit enter twice, you will see the "USB>" prompt.
5) Type the following commands (do not copy paste!!!):
Code:
set 1e 1
erase a0040000 c80000
erase a0cc0000 c80000
erase a1940000 640000
set 1e 06) Reset your phone and put it back in bootloader mode
But 1 question :
How i can find a topic to make a rom without activsync
Thanks
I'm truly sorry about the delay.
I've finally got round to posting a a STAR100 SuperCID guide.
1. Get itsutils: http://www.xs4all.nl/~itsme/projects/xda/tools.html
2. Run pdocread.exe with no args. Take a note of the "uniqueid" value.
3. Run "pdocread -n 1 0x000000 0x10000 -b 0x4000 original-bdk1.nb" - you'll get a file.
4. Head over to http://www.spv-developers.com/strtrkCID/. Feed it the DOCID and the file you got from steps 2 and 3. It'll give you back anoter file.
5. Run "pdocwrite -n 1 patchedfile.bin 0x000000 0x10000 -b 0x4000" where patchedfile.bin is obviously to be replaced with the patched file you got from step 4.
6. There is no 6. Report feedback.
Click to expand...
Click to collapse
All credit goes to itsme - he wrote all the tools and scripts which made all this possible.
Spawning script: perl startrek_cidedit.pl cid1e62995dd1db197b00b697388760b5e3.bin -i DOPOD601 -c 11111111 -o supercid1e62995.bin 2>&1
decrypting
bufend=44bdd4609845fd0931a871b4a31ddba42d4b96386f9 e9c5dff947c035432fc15
result=b2c7c4eede400853eb232eba436f394b3d75a9adf4c e9a1e452b26ea9059dc59
sha64k=8a7e3a8462b8c851ac125710d44abc05da4916f215e 331f98420db7ae5d87a5d
buffer checksum failed
why ?
Looks like the DOCID value you entered is incorrect. It should be a long stream of hex numbers.
Fantastic !!! Working Ok on SPV F600. Now, we need how to simunlock this smartphone.
Thank you very much Zone Mr.
i run pdocread in step 1 and got a dos screen that desaper in a second,and were i find the file in step 2.
Zone-MR said:
Looks like the DOCID value you entered is incorrect. It should be a long stream of hex numbers.
Click to expand...
Click to collapse
thank you Zone-MR,can u tell me how to get a long stream of hex numbers.
wlinsong said:
thank you Zone-MR,can u tell me how to get a long stream of hex numbers.
Click to expand...
Click to collapse
i know how to do,thank Zone-MR very very much
is there someone know how to flash rom use T-flash Card?
someone can't get the docid ,because you must use the old one!
I tried to do first step but when I ran pdocread.exe I get the following message :
Could not update itsutils.dll to the current version, maybe it is inuse?
try restarting your device, or restart activesync
or maybe your device is application-locked.
I've app-unlocked my device, activesync works ok, and restarting does not help. Phone is Qtek8500.
Any ideas?
Thanks
Is the script to calculate CID area for startrek available?
I think this should use the same method on Artemis or Herald, the problem is that they have G4 DOC and we'll not be able to use pdocwrite, but on those phones we're already able to place a hacked SPL in mem with psetmem.exe and jump into it's address with modified haret version. If we have the right CID area we can use the hacked SPL to flash it.
sorry for the ignorance...
I have downloaded itsutils but where is the dpocread.exe??
do I have to connect to the device with the mtty??
Maybe a bit more explanation
I've CID unlocked my Qtek 8500 and installed new ROM 3.6.251.0. Thanks Zone, great work!
Maybe it would be useful to write more detailed instructions, so here it is :
1. Application unlock your phone using regeditstg and do the following :
HKEY_LOCAL_MACHINE\Security\Policies\Policies\0000 1001 = 2 -->Change the value data from 2 to 1
HKEY_LOCAL_MACHINE\Security\Policies\Policies\0000 1005 = 16 --> Change the value data from 16 to 40
HKEY_LOCAL_MACHINE\Security\Policies\Policies\0000 1017 = 128 --> Change the value data from 128 to 144
Reboot the phone
2. Run SDA_ApplicationUnlock tool. Reboot the phone after it finishes.
3. Download itsutil.zip from http://www.xs4all.nl/~itsme/projects/xda/tools.html , version from 2005-6-28. There is even newer version, but with that version you can not use pdocread without arguments.
4. Connect the phone with activesync
5. Run Command Prompt, go to subfolder named "build" in itsutils folder, and run pdocread without arguments
6. Note the value of "uniqueid". It will be something like : "00 00 00 00 12 03 02 14 3b 07 1b b2 04 05 07 54"
7. run pdocread again with these arguments : "pdocread -n 1 0x000000 0x10000 -b 0x4000 original-bdk1.nb". This will make original-bdk1.nb file in build folder (where the pdocread is located).
8. Upload this file and value of uniqueid to http://www.spv-developers.com/strtrkCID/. It will open a new page after few seconds. Go to bottom of the page and click the link "Download patched BDK1"
9. Download the file (it will be named like "supercidxxxxxxx.bin) to "build" folder
10. Run the pdocwrite from command prompt with these arguments : "pdocwrite -n 1 supercidxxxxxxx.bin 0x000000 0x10000 -b 0x4000". Replace supercidxxxxxxx.bin with the original name of downloaded file from step 9.
11. Wait 15-20 seconds and that is it. Reboot the phone and install the ROM you like
It works! I've got now 3.6.251.0_02.67.30 on my Qtek!
Thank's, damird, your guide is unreplaceble for such lamers like me
But maybe anyone can suggest me were can i find and how to install (if it possible) Russian t9 or only russian lang to input? Or maybe how to rollback to original ROM with this that lang... (1.02.261.1)
Thank's
added:
Problem's gone, Russian T9 added.
Damird!
Cheers mate
Hello, can you share with us this script to calculate CID area in StarTrek?
With this script we can SimUnlock the StarTrek very easy (at least I think...)
Thank you very much.
I'm confused here... is CID unlock not the same with SIM unlock?
my carrier is tmob but I'm getting cing 3125 at ebay so I need to SIM unlock the phone for it to work on tmob right?
wow, pof, I can't wait for it! i had bought one herald in China but wireless was disable by default. I hope I could unlock the CID and get a WWE rom to enable the wireless.
sokelut said:
I'm confused here... is CID unlock not the same with SIM unlock?
my carrier is tmob but I'm getting cing 3125 at ebay so I need to SIM unlock the phone for it to work on tmob right?
Click to expand...
Click to collapse
Correct, you still need to pay to carrier unlock the phone. Check the wiki for links to a few services that are known to work.
CID unlock? Error installing ROM
I'm getting an ERROR [294] INVALID VENDER ID
I did the CID unlock
It starts to install the rom but when it gets to 4% I get this error. How do i fix this?
Can anyone help?!
Need a little clarification
Im stuck in steps 3-11. I've downloaded itsutils and I don't know how to proceed.
Hello,
i try to flash bootloader 1.01 mfg according to http://wiki.xda-developers.com/index.php?pagename=Hermes_BootloaderMFG
It hangs after
USB> lnbs SPL-1.01.nbs 50020000
...
start NB image download
According to other threads this behavior exists if mtty can not find the file. But the file is in the same directory as mtty.
Does anybody has an idea what is wrong?
Thanks
Andreas
did you do the "Task 32" first? and if you did did you get "Level = 00"
yes, but i only one 0
USB>task 32
Level = 0
USB> lnbs SPL-1.01.nbs 50020000
i got some output at this point, but i cannot remember exactly
???
? 50020000
? 00000000
????
The last line was: start NB image download
My device is SuperCID. SPL 1.09
there's your problem then; you need SPL-1.04.
I suggest you load Hard-SPL and try again...
also, might I heartily recommend that instead you download my MFG pack and use SSPL with 1.01 rather than flash it to your device... or at least use my patched 1.01 (create an NBH)
I get that message whenever I do not type the name of the file correctly, like for example, sp1-1.01.nbs instead of spL-1.01.nbs (the latter being the correct spelling). Just my two cents..
I had 1.09 before, coz I updated with full RUU versions of roms (like 2.06.502.3 cingy or 2.05.255.1 HTC), and I had no problem to downgrade to 1.01 MFG and now to 1.01 oli... I also used mtty, device was supercid, used commands was
USB>task 32
Level = 0
USB> lnbs SPL-1.01.nbs 50020000
USB> task 8
If I remember correctly, task 8 automatically SW reset herm... maybe I am lucky one?
take a look at your mtty icon. Does it say MFC or does it look like a serial connector. If it says MFC then you have the wrong version of mtty.
my guess: it says "MFC"
Thanks for all your answers. At the moment a'm at work and cannot try your suggestions.
But i have some further questions:
>olipro: there's your problem then; you need SPL-1.04.
According to the wiki:
"This is a very special bootloader which can be flashed in any bootloader version BUT to flash it your Hermes must be SuperCID first..."
...can be flashed in any bootloader... what does this mean? i thougt i can flash it from 1.09. sinmae was able to do it. (or did i miss something)
>crazyut: wrong file name
i checked this several times. i typed the right name, but i do not now whats the working directory of mtty. i put the nb-file in the same directory as mtty and startet mtty from a dos-prompt. so this should be ok.
>Sleuth255: wrong version of mtty
i tried to investigate this yesterday. somebody said he has version 1.11a. i have version 0.01. it says MFS. so this should be the problem. but this is the version from the wiki:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
http://wiki.xda-developers.com/uploads/mtty.exe
where can i get the right version? (at google i found mttty (3 t))
Thank
Andreas
Use the mtty.exe included in this pack, mtty and nbs file in the same dir.
Needed tools:
PuTTY ver.6 or above
Plink
Active Sync 4.5
any Hex editor
MTTY1.exe ver 1.11a
Windows PC
SPL 2.30 Olipro
SPL 1.01 MFG pack
SPL 1.10 Oli w/custom RUU
SPL 1.04 w/custom RUU
DUTTY'S Good .NB Tool
Win Rar
Hermes with working wlan
There are steps for the user with the device with the working wlan eeprom, and steps for the user with the device with the corrupted or missing wlan eeprom. Basically what you will be doing is cloning the MAC of a device with a working wlan, editing it, and flashing it to your device with the non-working wlan.
Steps for Working Wlan Device:
You need to get SPL Oli 2.30 (found on the XDA DEV FTP Site in the HERMES/HardSPL folder) on the working device. You can do this by following the downgrading bootloader page at:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=59&Itemid=27
Assuming you have HardSPL v7 on your device (as most of you have been doing upgrades and downgrades), follow the steps to downgrade to Oli 1.10 then to SPL 1.04, (read and execute carefully)
then use DUTTY'S Good .NB Tool...
http://forum.xda-developers.com/showthread.php?t=296311
...to convert the SPL Oli 2.30 .nb file contained in the .rar you downloaded (use WinRar to extact) to an .nbh file (RUU_signed) THEN flash SPL 2.30 (you can use the same custom RRUwrapper you used to flash to 1.04 by putting it in the same folder, but move the RUU_signed.nbh of 1.04 to another folder first, then put it back when your finished)
Download PuTTY and Plink and copy them into your C:\Windows\Temp folder
http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html
Put your device in bootloader mode and disable USB connections in Active Sync
Connect to the PC and open PuTTY
Click SERIAL, and make the speed 115200, and type \\.\WCEUSBSH001 (all CAPS) in the space for SERIAL LINE (overwrite what is there) or connect with MTTY first...
http://forum.xda-developers.com/download.php?id=9864
... and copy and paste the address into PuTTY then close MTTY. Type HERMES into the space named SAVED SESSIONS and hit SAVE. Hit OPEN. Press ENTER to get a CMD prompt...you will see a green cursor. Type Task 32 and it will return Level=0. Ok, close PuTTY as you have verified that it's working.
Sometimes your device will be seen as \\.\WCEUSBSH002 or \\.\WCEUSBSH003, just use which ever it connects to.
Now the next bit is tricky because you you will do it "blind" as in this mode, Plink does not have local echo so you won't see what you're typing.
Go to START/RUN/CMD
This opens a DOS window. Change directories to C:\Temp and type the following:
plink HERMES > herm1.nb (hit ENTER TWICE) (you will see the new file herm1.nb written in your Temp folder) (notice the spaces before and after the > sign)
Now type the following and hit ENTER (once) after each command:
task 32
password 0000000000000000 (that's 16 zeros)
set 1e 1
rbmc me.txt 500a0000 40000
that will copy the wlan section of the eeprom nand to the file called herm1.nb. You can right click on the file, select properties, and see that it grows to 256k-257k.
When it's done creating the file (to 256k or 257k, you'll see it doesn't get any bigger), press CTRL C in DOS to close plink and it saves the file at 257k size.
Open the file in a Hex Editor, and remove all the non usable Hex Data (basically the commands you typed) between offsets 00000000-00000140 up thru the Hex equivalent of the word HTCS. Delete the data so that you actually delete the word HTCS. Then at the end of the file, offset (00040000), delete from the very end of the file (right to left) thru the word HTCE. You delete the Hex equivalent of the word HTCE. You can leave the D+ ] there as we're only going to write 40000 bytes. Now the now MAC address is at ROW 0001F850 with two bytes at row 0001F860. The MAC reads backwards. Save it as herm1.nb (but not in the same folder as the original).
Now, since you've basically cloned another's MAC address (already allocated to another device), it's necessary that you change your MAC address ASAP. Instructions on how to do that below:
In the edited herm1.nb file, go to the MAC Address at offset 0001F850 and change the 2nd, 3rd and 4th bytes from the right... (it's your MAC address in reverse), to ANY numbers you like, keeping the same format. This 6 byte sequence is your NEW MAC ADDRESS. The last 3 numbers of the MAC (which appear in opposite order) can be "invented".
You now have the eeprom flash file to be transfered to the non working device...
Steps for Non-working Wlan Device:
Using the methods on MrVanx's downgrading SPL page...
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=59&Itemid=27
...downgrade again to SPL 1.04, then flash SPL 1.01 MFG. When flashing and using SPL 1.01 MFG, some users suggest you only use the version of MTTY that comes with the MFG Pack.
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootloaderMFG
Read the full instructions before flashing.
Ok, now that you have verified that you have SPL 1.01 MFG on the device, put in bootloader mode, disable USB connections in Active Sync. Connect the device and open MTTY. Make sure you have copied your herm1.nb file into the same folder as MTTY.
Connect to the device (\\.\WCEUSBSH001)
and hit ENTER to get a CMD prompt
Now type the following:
task 32
password 0000000000000000
set 1e 1
lnb herm1.nb 500a0000 40000
Hitting ENTER after each command.
When it's done, close MTTY and reboot your device and verify that your Wlan is now working...
Then I recommend flashing HardSPL v7 or SPL 2.30 to your device right away (because you know you won't leave your device alone and we don't want you bricking your Hermes, do we?)
BTW, if you want to do a full backup of you FULL eeprom nand at any time, connect as before and type these commands:
plink HERMES > full.nb (hit ENTER twice)
task 32 (hit ENTER once and only once from now on after every command)
password 0000000000000000
set 1e 1
rbmc me.txt 50000000 7fff800
watch your file grow to 128 MB.
If you ever need to flash the entire eeprom nand, just edit it as above so you take out the commands you typed (HTCS-HTCE) and you're good to go...
Thanks go out to Pof and Olipro for doing the initial research on this issue. And also to members Laikos and Panzer who helped tremendously.
Tested on Cingular 8525 Wm6 VP3G modified AT&T rom, and Orange m3100 WM6 cooked rom based on Dopod 3.54.707.3 rom.
*NOTE* Olipro just posted later in this thread
"just to point out guys;
to flash 2.30.Olipro, just convert it into an NBH then run SSPL on your phone and go ahead with the flash, same goes for loading any other SPL, just load SSPL first (or use Custom RUU with the NBH and select force SSPL) the downgrading is unnecessary"
another member (dan1967) suggested that one only have to use SPL 2.60 Oli Hard SPL v9 Developer Edition to do this procedure and one can avoid the upgrading and downgrading of bootloaders...
Member alakentu has translated this method into Spanish. The thread is here:
http://forum.xda-developers.com/showthread.php?t=364751
***DISCLAIMER.....TRY AT YOUR OWN RISK, WE ARE NOT RESPONSIBLE FOR ANY MALFUNCTIONS OR OTHER ISSUES THAT MAY OCCUR.***
For those of you who used my guide to fixing your dead Wlan on Hermes, please feel free to make a donation via paypal if you feel I've helped you in some way. Any amount will be very much appreciated, and I could really use the cash, hee hee, thanks in advance. Just click the PayPal Logo below to donate.
cool !! I try this if i found a phone with no dead wlan
nice.........
It's possible to just hand code the WLAN EEPROM Value to your dead WLAN EEPROM too. Download your dead EEPROM and Edit the location mentioned by drummer.
Warning: It took about 30 mins to hand code the WLAN EEPROM DATA.
Would it be possible for someone to extract the eeprom file from a working wlan device, "zero-out" the MAC address portion, or replace with 'FF' or some other 'dummy' value, and post this here, so those of us without access to a working device can use to flash our damaged devices?
By "blanking-out" the MAC address in the attached file, you dont risk having your MAC address used by everybody, so there is no "legal" risk, and help us without a working device to fix ours...
Thanks for the solution guys and hopefully you can post the file here for us to use.
Good work !!
Thank you very much for this solution !!!! Great job!
But as said chrisvor, could you post an extract of a working Eeprom for thoose who don't have one please...
Thank you !
drummer,
first of all is to say thanks to you all who put in their time and effort in resolving this problem
so my question is... can you post the file of working wlan bit for us, without that i can't solve this problem... =(
Thanks!!!
Thank you so much for this!!!!
I will try to reviving my X01HT WiFi later!
Great Job!!!!
Someone has repaired his hermes ??
nicoebra said:
Someone has repaired his hermes ??
Click to expand...
Click to collapse
I did. And so did Laikos. Actually, he fixed his about 20 minutes before I did, he is a better editor than I am. Why do you think we did the research? We both had devices with non-working wlans, and now they're working again.
...and no, we're not posting, or sending anyone the file. You have to find a friend that will help you, as your trust in each other will safeguard against any possible mis-use of this technique.
laikos said:
It's possible to just hand code the WLAN EEPROM Value to your dead WLAN EEPROM too. Download your dead EEPROM and Edit the location mentioned by drummer.
Warning: It took about 30 mins to hand code the WLAN EEPROM DATA.
Click to expand...
Click to collapse
I don't believe that this is a good idea, as you don't know what else (from EEPROMcode) is corrupted!!
The MAC address is the only visible part to us...
pop20032004 said:
I don't believe that this is a good idea, as you don't know what else (from EEPROMcode) is corrupted!!
The MAC address is the only visible part to us...
Click to expand...
Click to collapse
How did you come to that conclusion?
All Laikos was suggesting, is you could type in the data, rather than replace the data by "cloning" it from another's device. Once you know the offsets, which you do if you read this technique, it's quite easy, although time consuming. So far, each file we have examined have had the identical wlan signatures, and identical first three numbers of the MAC address. That suggests that HTC was assigned a set of MAC addresses by OUI for their use.
BTW, using SPL 2.30 oli, you can change your backup CID, and model number (Hermes 100, 200, 300, or whatever you want to change it to like "Hermes 911").
Help
I believe that would be better than someone give the instructions detailed for those that they do not have other device to the hand to extract the EEPROM, extract your corrupt EEPROM and edit it.
In my case, live in Mexico city and these devices are extremely rare of seeing by here.
As soon as if someone can help me to obtain the file of a EEPROM will be I thanked what is.
Open the file in a Hex Editor, and remove all the non usable Hex Data (basically the commands you typed) between offsets 00000000-00000140 up thru the Hex equivalent of the word HTCS. Delete the data so that you actually delete the word HTCS. Then at the end of the file, offset (00040000), delete from the very end of the file (right to left) thru the word HTCE. You delete the Hex equivalent of the word HTCE. You can leave the D+ ] there as we're only going to write 40000 bytes. Now the now MAC address is at ROW 0001F850 with two bytes at row 0001F860. The MAC reads backwards. Save it as herm1.nb (but not in the same folder as the original).
i can't edit file " herm1.nb"
you can guide again or help me to edit my file.
Hello,
Is it normal that my file herm1.nb is rained large that 30Mo at the time of that creation, thank you.
-------------
Edit:I excuse myself I have to make an error the first handling, I succeeded in having the file herm1.nb has 256 Ko (262 ' 439 bytes).
If I do not modify the mac address that you it will occur on the other apparatus, thank you
drummer10630 said:
...and no, we're not posting, or sending anyone the file. You have to find a friend that will help you, as your trust in each other will safeguard against any possible mis-use of this technique.
Click to expand...
Click to collapse
@drummer10630: I do appreciate all your and Laikos efforts to solve this problem and to let the whole community know the method so everybody can fix their devices... however, the reason I asked if anybody could post the file was not a sign of "laziness", rather it is due to the lack of friends who have a TyTN or who want to void their warranty by flashing a non-official bootloader in order to "do me the favor" of extracting their eeprom data.
If any of you guys have extracted the eeprom and you have edited it to include your MAC address, could you please edit a COPY of this file, put "FF" in all the bytes of the MAC address (which is the only thing that "ties" this file to your purchased device and hence yourself), and post it here for us "tytn-friend-less" people to use?
Many thanks for EVERYBODY's efforts in solving this
Thanks and kudos go to Pof and Oli ofcourse, due to whom none of this would be ever possible !!
Chris
I have tried to get the code from a working Vario II using Des' SSPL, to avoid all the flashing of a working device, but got
Code:
USB>task 32
Level = 0
USB>password 0000000000000000
HTCSPass1.
CMËHTCEUSB>set 1e 1
USB>rbmc me.txt 500a0000 40000
GetExtRomData+(): *pszPathName=me.txt, dwStartAddress=500A0000, dwLength=40000
USB>c=40000
... and no dump.
Is there a workaround?
jrp said:
I have tried to get the code from a working Vario II using Des' SSPL, to avoid all the flashing of a working device, but got
Code:
USB>task 32
Level = 0
USB>password 0000000000000000
HTCSPass1.
CMËHTCEUSB>set 1e 1
USB>rbmc me.txt 500a0000 40000
GetExtRomData+(): *pszPathName=me.txt, dwStartAddress=500A0000, dwLength=40000
USB>c=40000
... and no dump.
Is there a workaround?
Click to expand...
Click to collapse
According to the #1 post, you HAVE TO follow the instructions, i.e. downgrading to SPL 1.04, 1.01 MFG, Olipro 2.30, in order to save the eprom from the working device.... no shortcut I'm afraid
I removed the lines 00000000-00000140
But I do not have information with the line 0001F850 and 0001F860 is this normal? , thank you.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Quick question.... Could I dump the WLAN eeprom from a Wizard? Dont think so, but I thought I'd ask since I have a wizard lying around too....
I can't flash SPL 1.04 over mtty.
Code:
USB>
USB>task 32
Level = 0
USB>lnb SPL-1.04.nb 50020000
Command error !!!
USB>
What is the problem?
igord said:
I can't flash SPL 1.04 over mtty.
Code:
USB>
USB>task 32
Level = 0
USB>lnb SPL-1.04.nb 50020000
Command error !!!
USB>
What is the problem?
Click to expand...
Click to collapse
PLEASE tell me why you are trying to do this outdated DANGEROUS operation??
Download duttys nbh tool, pack the .nb file into an RUU and do it using safe SSPL........messing with mtty can be a risky business.
Hi.
my phone mtty conection is not working...
When the mtty is open the only thing i see is: CLIENTCLIENTCLIENT
So, untill i get this thing working i can't try any more updates to bring alive my RADIO!!!
can anyone help me to configure the phone, or the MTTY?
THANXS!
cauboi25 said:
Hi.
my phone mtty conection is not working...
When the mtty is open the only thing i see is: CLIENTCLIENTCLIENT
So, untill i get this thing working i can't try any more updates to bring alive my RADIO!!!
can anyone help me to configure the phone, or the MTTY?
THANXS!
Click to expand...
Click to collapse
Did you disable Active Sync USB?
Yes, many times i check and unchek the "Allow USB..."
Which SPL do you have?
hi, my phone is:
At&t 8525
IPL 1.04
SPL 2.30
Radio (unknown, i don't remember but i gues it will be the orginal 1.54)
ROM 2.15.502.3 (04/09/07)
Thank you for reading!
You can't use MTTY with SPL 2.30, you need SPL 1.04, SPL 1.06 (no rtask command), but the best SPL to use with MTTY is 1.04.
igord said:
I can't flash SPL 1.04 over mtty.
Code:
USB>
USB>task 32
Level = 0
USB>lnb SPL-1.04.nb 50020000
Command error !!!
USB>
What is the problem?
Click to expand...
Click to collapse
you should flash SPL With RUU;MTTY command work with SPl. so the MTTY commands different form different SPL
Version.