Help me revive my G4 8125 :( - G4

Hello to everyone. I am newb here. I need a great men to help fix my phone. I got a Cingular 8125 G4 CID-locked but sim-unlocked device. Prior to upgrading, it finely works in a Cingular Official ROM and WM5. Now I decide to put some more interesting rom - a AKU 2.3 rom (if i am not mistaken this is a Wizard Love Rom). It was upgraded successfully. Then I flashed another rom which I am not familiar with the content. Unfortunately didn't go right this time. Now I am stuck with RGB screen. I even use shelltool in RGB screen (even knowing not to work in this kind of mode). In the middle of the process, the device turns off and shelltool hang, never show progress. I pull out the usb cable from the device. Then when I turn on the unit it gives me the RGB screen showing IPL/SPL 2.25.0001 with no splash screen, OS and GSM. I tried flashing different rom which I know is safe for G4 CID-locked device but no luck at all. I can get through 96% and the device turns off automatically and return to blinking RGB screen with on and off usb connection. Did I bricked my device? Please help revive my Wizard 100. Thank you in advance.

Nopes ! your phone is not bricked,as long as it gets into Bootloaders (RGB screen) its safe.
Download official cingular stock rom and flash in Bootloaders to recover or flash wizard_love rom.After recovering,don't use shelltool,its risky and old method,now a much better method is available.Either upgrade through 'SoftSPL or HardSPL'.

Thanks for the reply I appreciate it. I did all that, download the cingular official rom from the link I got from xda forum and wizard love rom and flashed it but no luck at all. It gives me the same problem. When doing the upgrading the phone restart at 96% and reboot itself showing different error every upgrading attempt. What I only got in bootloader screen is the IPL/SPL 2.25.0001 no OS and GSM (Radio Rom). Maybe I got a corrupted file in my phone. Or just my battery. I tried wall charging but no good. Should I buy a new one or try my luck again. BTW, the error message appeared during upgrading are 274, 302 and 260. The first two seems to be serious matter. Please help me.

Probably,the battery is the culprit here,if its not fully charged or not having enough juice,it won't complete the flash,there are many comm errors due to weak battery,try to get it charged and then try.

How many hours just to have a fully charge battery using wallcharging?

Or maybe my battery needs to be replace. FYI it's 1 yr and 8 mos old now.

My Wizard was revived this time. The problem was the dead battery. I bought a new one and everthing goes fine when I flash the Official Cingualr Rom. Thanks to zabardast_1 and the gurus here in the forum.

Thanz !
It was pleasure to help you,glade you got it up and running

Related

Help! Touchscreen on way out. Need to go back to WM5!

Please help me. I recently upgraded to the Black satin rom and everything was fine. However the touchscreen on my M3100 has started to go haywire.
After being on for about 5 minutes the touchscreen doesn't work. It seems like the top right hand corner is faulty as the close button keeps being pressed again and again. I think it is probably the phone that is faulty rather than the ROM.
Anyway I need to revert back to the original Orange ROM (WM5) so I can send it back to orange. I've only had the phone about 3 weeks so its still under warranty.
I tried to load the ROM off the orange business website but it errors when trying to load the rom on. I assume I need to downgrade the bootloader thingy.
Any help much appreciated!
www.mrvanx.org
Look for "downgrade guides"
I'm in a similar boat mdavix!
I've just tried flashing an original T-Mobile WM5 ROM using MrVanx's guide but it doesn't progress beyond the bootloader page. Instead the update times-out and gives Error 260 - "Cannot connect to PDA"
Getting late (that's when Bad Mistakes Happen lol!) so will come back to it at the w/e I hope. Let us know if you have any luck!
sim
--
T-Mobile MDA Vario II / schaps 3.57a / Radio 1.41 / HardSPL
interestingly, I put black satin on my new M3100, and the screen started going. So I put it back to the latest Orange release (from the website) 2.11.61.1, but it was still screwy. Sent it back to Orange, and got a different recodnitioned phone back. They said the ROM was the issue, and the one they gave me had 2.11.61.3 on it. This version is not available for download... has anyone else seen it?
Do orange know what is happening to the screens? Is something getting burnt out? does 2.11.61.3 have a fix?
Well... I'm too scared to put WM6 back on, now, although I really want to. I at least want to wait till I can get hold of the update for 2.11.61.3, and even then, I'm not sure.
I have looked at the downgrade guide but don't really fancy the re-compiling the nbh business.
The strange thing is that if I take the battery out for a couple of minutes, then replace and boot up, the screen works for a while!
Is it worth trying a different rom?
mdavix said:
Is it worth trying a different rom?
Click to expand...
Click to collapse
No, it's a hardware problem, I assure you.
Ok, thanks vp3G.
So I still need to get back to WM5.
I'll have to give mrvanx's downgrade guide a go!
Is this still current? Is this the correct one to try?
I carried out the steps in the downgrade guide and attempted to flash the resultant rom onto my M3100. It started to update got to 1% and failed with a transfer error!
Now when I turn the phone on it just comes up with the three colour screen!
Have a broke it forever? The screen reads:
HERM100
IPL-1.01
HERM100
SPL-2.10.Olipro
Please help!
Phew! Panic over, I've managed to get the Black Satin rom back onto my phone.
I'm stuck at the screen alignment screen again but at least its got an OS on now!
I still need to load WM5 on tho. I think I'll try re-doing the downgrade guide and see if that helps.
I'm looking at duttys nbh tool and notice that the device id is HERM200. My phone is an M3100 so a HERM100. I'm going to change the value to be HERM 100 and re-compile. Hopefully that was the problem last time!

G4 Wizard bricked...CAN access bootloader

Hey guys...I believe my G4 device is bricked yet still recoverable.
I was flashing the htc 8125 update today to my wizard from the vanilla WM6 ROM. (Yes I want to go back to originial WM5).
I'm still quite new to this whole flashing scene, but that's besides the point.
I tried using the EXE of this ROM:
RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1.e xe
and after that didn't work I believed that maybe I should try using shelltool, which I used for the Vanilla WM6 ROM.
It went for about 35 minutes...then I decided to pull the cable. Shelltool said it completed the flash..so I hard reset the device. It didn't get past the cingular splash screen.
Only until later did I start believing that this was a G3 only ROM.
I'm still unsure whether it was g3 or g4, but my device is a G4.
I believe i can still get into bootloader(the 3 color screen I believe it is), but can't connect to the USB to flash any other ROM, or so I believe.
When I plug in the USB the device shows that it is connected, yet the computer doesn't do anything.
I have no idea, i've been searching google, searching XDA with google, maybe just not using the right words.
the device
SPL/SPL is 2.25.0001
GSM 02.25.11
OS(Believe it is displaying the OS it was supposed to be AFTER flash): 2.25.11.1
Can anyone direct me down the right path?
Flash with your original stock ROM, then SoftSPL/HardSPL and proceed with the update.

HTC 8125 Bricked or NOT? What next?

Hi guys I need some help. I have a Cingular HTC 8125, I was trying to upgrade the rom on it to a new WM6 and here is what happened.
I have been researching the topic for about 3 weeks.
Its a G4 Device being upgraded with VISTA w/ Moded drivers for Ative SYNC
IPL 2.25.0001
SPL 2.25.0001
I used the shell tool to install one of the roms waited about 2 hrs and finally noticed that the window was NOT RESPONDING so I had to shut down and start over. The phone got to the second screen but froze there now showing
IPL 2.25.0001
SPL 2.25.0001
GSM 02.25.11
OS 10.1.0.811
On the Cingualr Background, I can still enter the Bootloader screen but nothing else?
Nothing else happens I cant connect the phone to the PC to do anything else.
Is it bricked or not is my question and what can I do to flash OEM rom or something that will work.
I tried OEM Cingular rom but I get ERROR 260 No connection to the phone?
Any help will be greatly appreciated!
Bricked phone
You should had firstly either hardspl or soft spl the phone b4 trying to load any rom
It's not bricked as long as you can see the RGB screen (Colors red, green and blue)showing the same IPL/SPL such as yours; IPL: 2.25.0001 and SPL: 2.25.0001. AND PLEASE BE CAREFUL WITH YOUR DEVICE CAUSE ITS G4 MEANING YOU CAN NOT JUST INTALL/FLASH ROM. Make sure that the Rom you flash not contain G3 IPL and SPL which is 2.xx.001. If so, then you will bricked your device.
Desiji is right, you should install rom with softSPL or hardSPL.
Try to flash the Official Cingular Rom or Wizard Love Rom. If success, then you can install other Rom using what desiji said. Just make sure that its a G4 safe rom. And another thing, try to charge battery using wallcharger not in the device. U need enough battery to perform rom flashing.
Hope this help revive your Wizard.
esdee007
WOW !
grrrrr8,you are a quick learner
CateraMV6
Yeah ! I certainly agree with esdee007 and desiji
Thanks
Hey guys thanks, thats what I thought but I think my main problem is the VISTA I need to get a hold of XP and try all that because the Vista is having issues with connecting to the phone at the moment, I can not get it to show it as a device. It does make a beep noise when you connect/disconnect it so its doing something but Vista is just too much of a pain in the rear to deal with.
Its a good news that its not bicked so all hope is not lost.
What is the opinion on Tmobile WING!? any reviews should I get that phone instead?
BTW where do I find these G4 Safe ROMS? and how do I tell if they have the IPL/SPL in them? Do I need to hack them to tell?
And is Soft or Hard recommended?
YUP ! sure vista is still not compatible for flashing,WinXP is highly recommended and trouble free.
All official stock roms are safe to flash both the devices G3 or G4,secondly,all the latest custom build wm6 or wm6.1 are safe for both the devices,as they don't include any IPL/SPL in them.
If you plan to flash many roms,than 'HardSPL' is recommended,coz its done only once and the device remains semi_Cid unlock untill you personally remove HardSPL,but with SoftSPL,its done everytime you want to flash a new rom,choice is all yours,how you want to go about it.

Upgrading my Jasjam HREM100 Failed with Error [262]

Dear Members,
I tried to upgrade my JasJam with "838Pro_HK_ENG_WM6_Upgrade_20070712"
Which worked with other JasJams (Many of my friends has it working).
On upgrading, it stucked on 11% saying Error [262]
I went through recovery, and it said remove the USB cable, remove the Battry, Return it, start the phone, connect the USB, and its recovered.
After that Its again stucked in 100% and the same senario is happening.
Please tell me is there any possibility to restore my phone working.
Its stuck now, and only the (Three color screen) is on the screen.
Hard reset, soft reset is not functioning, and the phone refused to show anything except the three color screen.
I searched the forum, but found no relative article, I am searching since two days your forum and I know that no other forums can help me in this as I was always getting my help from yours.
Thanks for your time.
HERM100
IPL-1.04
HERM100
SPL-1. 40. 0lopro
If you're using XP then untick "Allow USB Connection" in activesync.
Reset to bootloader on your Hermes, Hold power, OK button above flywheel and reset with stylus.You will get the same screen you have now but it won't be a f*&%ed up version of bootloader. Connect to PC by USB and Install Hard SPL V7, found here - http://forum.xda-developers.com/showthread.php?t=296722
After this, use the sd card method to install the ROM.
1. Format a 2Gb or less sd card FAT32. ?CFopy the .nbh file of the rom you want to it and rename to hermimg.nbh .
2. Insert into phone and reset to bootloader.
3 If you did everything right then follow the prompts...
Cheers...
Again problem!
Dear ultramag69,
Thank you for your fast reply.
I did (untick) that option in the ActiveSync.
And also did reset to the device by holding the Power + Ok (under the flywheel) with Stylus reset.
After that I downloaded "Hard SPL V7" and tried to update.
First of all, in the "Hard SPL V7" there was only the last option active, and there was down a checkbox also active, but when choosing the last option, checkbox bocomes like everything else disabled.
However, I got the erro 286
I felt like the Device disconnected from USB and reconnected again (Windows gave me the sound when you remove some USB device and you re-connect it again) :-|
I don't know what to do with this dead device now !
Thank you very very much for your time and help
Don't quote me on this as I suspect you need Hard SPL V7 but, as yo've tried things out and you're about to quit anyway, Try using the sd card to update the Stock rom, the rom that came on your Hermes, or updated version. It might let you do it if the CID matches.
I don't believe SPL 1.40 allowed you to flash ANY rom but it may let you re-install the stock rom BUT it must be the original carrier software it came with. If you had Telstra rom on it when you got it, it must be a telstra rom you flash. Make sure its for the right country too as some carriers are all over the world.
Cheers...
Hello ultramag69,
Thanks alot for your reply.
Having my i-mate dead, is really interesting.
I am trying to recover it up, Mine came with (HTC) logo when booting, and I did flushed it with Dopod.
But recently, the network stopped, and I asked some experts, they said it need new OS (They ment to re-flush the ROM).
I tried with the same Dopod that was successful before, and its now stucked on 11%.
I even downloaded the Telstra but the same, it stucked on 13%.
This is my entire story, and still I am trying to get it up.
Thanks alot for your helping. nice of you.
And for all who read my post, if they had such experience before, please help.
Hello ultramag69,
Thanks alot for your reply.
Having my i-mate dead, is really interesting.
I am trying to recover it up, Mine came with (HTC) logo when booting, and I did flushed it with Dopod.
But recently, the network stopped, and I asked some experts, they said it need new OS (They ment to re-flush the ROM).
I tried with the same Dopod that was successful before, and its now stucked on 11%.
I even downloaded the Telstra but the same, it stucked on 13%.
This is my entire story, and still I am trying to get it up.
Thanks alot for your helping. nice of you.
And for all who read my post, if they had such experience before, please help.
If you can, try to find the original SHIPPED STOCK ROM. It may be your Hermes won't be recoverable as the flash stopped in the radio rom part. Most people use a cooked rom as this has the radio rom part out.
I personally use the sd card method to flash my roms so there are no sync errors or accidents with my PC. But you need Hard SPL V7 installed to get that to work with any but the shipped rom.
DON'T try flashing anything but the shipped rom or you will loose all chances of recovering your Hermes.
The only other suggestion would be to flash the SHIPPED RADIO ROM, but you need to know what radio it was before you flashed it with the dopod rom.
Unfortunately the radio rom is the Achilles heel of our phone series. Any problems during flashing of that means we pretty much end up with a brick 99% of the time. Most people are stuck and the rest seem to have limited success reflashing the radio. AVERY small percentage get it working with no trouble, but its a REALLY small amount of people.
Good luck, Make sure you flash with the SHIPPED STOCK ROM to improve your chances of success.
Cheers...
Ultramag69, Thanks alot for your consideration.
Flusching using SD card didn't success with SPL V7.
I formatted my MicroSD card, 2GB with Fat32 FS.
After that I copied the file that came with the zip archive (RUU_signed.nbh) and renamed as required: (herming.nbh).
And I put it in my i-mate, and holded the (Power + OK under flyweel) then restarted using the stylus, It showed me the tri-color screen, then it shows (Loading...) with Gray background screen (Which is normally the flusching screen) but it returned to the tri-color screen.
Any suggestions to get this SPL V7 installed successfully ?
I tried with all my (.nbh) files that I have downloaded from all sources, but its the same screen.
I think something is really wrong with me i-mate, should I take it to some Hard-ware service center ? and what can be damaged and need to be replaced in such cases ?
I am very excited in getting it working again.
Thanks alot.
Cheers...
I had bricked my Hermes a couple o' times, because of a rom I cooked half-way ( LOL ). Each time I had to flash back to the stock rom as suggested. Don't lose hope, cuz there's some people who will tell you just to accept it as bricked. You could also take the sucker apart and use jtags to flash. Most types of bricks can be solved when it comes to the Hermes. There's a thread somewhere that polled the different types of bricks, and except for radio bricks, most can be solved. If you unbrick it try 6.5 .... !!! My rom is cooked all the way now
Arwany, did you run the SSPL.exe file in the sd card instructions for Hard SPL found on page 116, post 1160 of the Hard SPL thread? You need a version of Soft SPL (SSPL) to flash using the sd card as the CID must be bypassed. The reason we Hard SPL our Hermes is because its safer. Its worthwhile flashing the SPL using unsafe SSPL (even if you use the pc you have Soft SPL installed) as its a short flash, flashing a rom (especially stock roms with the radio rom inside) is a riskier and longer flash.
Cheers...
I had the same problem.. All you have to do is establish a connection with Actisync, then run the Updater. There will be 3 colors on your Screen, sont worry, just wait 10-15 min and your should be done with the setup.
Want to help
Arwany said:
Ultramag69, Thanks alot for your consideration.
Flusching using SD card........ with the zip archive (RUU_signed.nbh) and renamed as required: (herming.nbh).
And I put it in my i-mate..........
Click to expand...
Click to collapse
Hi,Just to tell You that I've noticed a little spelling mistake.You've written "herming.nbh" But it should be "Hermimg.nbh".
Not the 1st person to make that mistake, and probably won't be the last.....
Hi All,
Yeah, that worked out for me, I could successfully flush my JasJam with that.
Thanks for your reply.
I am still facing problem when trying to flush with other OS, its always stuck on the GSM line.
I am using the SD flush method.
Any suggestions ?
THank s alot for your help!
If you have the no GSM problem the only way to, maybe, fix is to flash the original SHIPPED STOCK ROM, or the original radio rom. Flashing anything else may result in a permanent brick...
If it doesn't succeed then, sorry, its not repairable. Can be used as a PDA but not as a phone ever again.
Cheers...
Thansks Ultramag69, for all the helps, It solved my main problem.
You also Ekonkar, your comments was so helpful.
I will try to do some hardware repairing in some Mobile shop, they may get it up again !
To fix it will cost more than to get a new device... They'll tell you they can't fix it or it needs a new mainboard. Will still cost you for this nugget of info. My advice, buy a Hermes off ebay, either working or not. If its not, make sure its screen related problem cos you have the parts to fix... Unless your screen has gone bung too...
Cheers...
I gave it to the repairing guy, he replaced the GSM item and its up and running now for only 20$.
Prost :-D
Sweet, You should post where and what country so others in the same situation might be able to get their Hermes up & running.

G4 Bricked? Tri-Color boot screen visible

Hi. I have searched the forums, but haven't found the answer I have been looking for, so sorry if this is a repeat.
I am working under Windows 7, installed VMWare and XP Pro on it, and easily installed Hard-SPL and Cracings 6.5. When I went to upgrade the Radio, I was sure to download one without SPL and IPL. I tried to upgrade, but it hung at 2% for at least 5 hours. (I knew it was bad in 2 minutes actually, but decided to wait). Now it will turn on, but to the tri-color boot screen. Tried hard reset (although I didn't really expect it to work). Is there anything that I can do? It shows when I connect it to usb, both on the phone and on the computer.
It is FAR out from under warranty, so thats out, but if there is anything I could try, I would be much obliged for pointers. Thanks a lot!
-Jotek
You need to make the update with RUU 2.5.2
( http://forum.xda-developers.com/showthread.php?t=314952 ).
Try it, if even that does not work (for me it works only with wizard_love ROM
( http://forum.xda-developers.com/show...293480&page=21 loca's post), but not with other cooked ROM's) then you can try WST wizard service tool
( http://forum.xda-developers.com/showthread.php?t=329170 ) to unpack the nbf and load only the OS ROM.
Thanks for the info.
I will try it later this weekend when i get time! (moving to new apt.... sigh... can't feed the addiction)
-jotek
If Tri Colour Screen WST needs to boot into WM OS surely???
How can you use WST if only on bootloader. Please explain as I have similar issues...
Dilbert
I had exactly the same experience as you: Hard-SPL followed by Cracing and then the tri-color screen. This thread helped me revive my G4.
http://forum.xda-developers.com/showthread.php?t=442126
Hey I am having the same problem but with my G3 att 8125. I flashed to 2.26 which I always do before installing any rom then installed X2A Haseebs Iphone Killer and it stalled at 57% for over an hour so I unplugged it and hard-reset it. I have installed this rom about twice and it works fine. Now my phone starts up and goes straight to the Tri-colored bootscreen. When I plug the phone in it displays that it is connected via USB but the computer doesnt recognize it. IPL 2.26, SPL 2.26 as displayed on the screen. PLEASE HELP!
Hi all, I've got the exact same problem as Quadzilla has - any help would be much appreciated!

Categories

Resources