Please help me fix the camera of my Cingular 8125 G4 device. After I flashed a new rom using soft SPL method, which I think G4 safe rom, the camera is not working. When I press the camera button, I only see the spinning circle with different colors and the screen lights up a little bit than the normal brightness and stuck it there. And after a few seconds, the phone hangs up. Need to soft reset in order to put back the device in a functional state. I don't know why this happened as I followed all the necessary steps in using softSPL upgrade method. Maybe there is something wrong in the device registry. Does anyone has the same camera problem. Please share the tricks, tweaks or anything just to bring back the camera function again.
BTW, I reflashed back the official cingular stock rom but no luck at all its the same.
I see that you are using the TNT ROM, so I would to and flash UP to the newest version and see if that fixes your problem, it sounds like the camera software and drivers are not getting installed for some reason.
I reflashed the tnt rom but no good. Tried also to go back to the original cingular stock rom but still not working. Even in the windows\camera cannot make it. But when tried not to use the device for a some hour in standby mode, the camera works for a while then it hangs up. And go back to non-functional state.
Sir, what you think is the problem? I suspect its the software installed in the device based on what the camera behave. Or definitely the hardware itself and need to replace. Bad for me because I am living in the Philippines and as far I knew there is no service available in our country.
Thanks in advance whatever help you can give. Have a nice day.
Try using the wizard service tool to increase your page pool to 6mb.
Camera work again after....
My dead camera work again after I flashed rom cooked by Cracing. This rom is awesome. Its compatible with Wizard. Thanks to Cracing.
Related
Hi everybody:
I installed the udk syrius 7 rom Polaris, when activate my camera
it doesn`t show imagen, it`s black andy show the news
text:
Unable to capture photo. Unable to get frame data from
camera device.
Can you help me??
Thanks a lot ¡¡¡¡
Same here!
Same here!
I tried several roms and I still have the same issue.
Tried downgrading the radio, didn´t work either...
Could it be the SPL?
I have had the same problem. I have resolved with a new one flash of ROM
SPL is OK !
Just go back to a original rom (incl radio) and after that try again.
If that doesn't work just try a other radio rom.
Most of the roms have different radio requirements
Some need 1.58****
Other need 1.59****
Normaly the rom maker gives that info.
Sometimes the camera malfunctioning is a software issue.
As i experienced it is a hardware issue when you still have the troubles when you go back to original rom and radio rom. Although there are tons of users which get the camera to work after installing some package etc, my defect was loose connections on PCB/CPU or something similar. Thats why the problem starts slow, sometimes it works, somethings it doesn't and in the end it doesn't work at all.
The only thing you can do then... is return it for warranty.
Hello there,
I start this thread because i need some help from you guys.
Hopefully by this way a quicker answer or solution....
posted already my problems in here:
http://forum.xda-developers.com/showthread.php?t=497347&page=122
http://forum.xda-developers.com/showthread.php?t=501147&page=21
And now here again...
when i flash this rom v3.3.1_3g_16_keys or the Insomnia 3G, i get problems with my dialer, When i press the phone button or try to dial a number i get a crash screen? it is not working. what to do?
I flashed to Radio 1.71.09.01 and also with this radio the 3G version roms are not working, the dialer part, still the blur sreen when i press the send button or try to dial a number!
The Insomnia - 2G are running without any problem at all? or the current one, is running smooth on my Niki 100 >>> Clean Black 6.5.2
Why i cant run the 3G roms? video dialer not supported in my country? or what - please any comments!
Sorry double posted after editing
Finally someone who is dealing with the same problems as I had.
I had the same problems with my other Nike, I could flash the original rom's or a 2g version but not the 3g version.
The problem wasn't 3g but only the dialer.
Randomelements suggest me to see if I had some bad blocks by using mtty, I didn't try that option because I sold my Niki, and now, after a short period of using an Iphone (that I didn't like at all) i finally have a Nike which is not having that issue.
I know it drives you mad because nobody has having that problem, the only thing I did was searching for a dialercab and I always installed it after I flashed a 3g rom.
I know this is not a real solution but I'm very curious if you can fix this issue.
(or maybe you get your hands on my old Nike )
Goodluck
did you always hard-resetted after flashing a new rom?
Hard...
twolf said:
did you always hard-resetted after flashing a new rom?
Click to expand...
Click to collapse
I always use the customRUU with hard / soft reset option build in when i flash and i do a hard reset...
Good this possibly make any sense if do or not reset hard....
i have the same problem. i think it is insomnia 3.x problem.
in my case after hard reset i flashed new rom - ok,
i set up all settings, install xt9 - rom stuck. ok, hardreset.
set up again, is ok, but after 1 day it can't boot. ok
hardreset, flash again, hardreset, no set up, using clean rom,
next day can't boot up.
flash new radio, newest, older, the same problem.
fail.
flash NIKI Clean Black - works perfect - fast and smooth.
Are you guys flashing back to an original rom?
My niki was stuck in a loop not too long back, would not boot up properly, thought it had given up the ghost, it is a company phone so was going back to original t-mob rom. But this cured my problem, phone now works fine with any rom.
Try it, get an original rom, flash back, then try anything.
SteveCac said:
Are you guys flashing back to an original rom?
My niki was stuck in a loop not too long back, would not boot up properly, thought it had given up the ghost, it is a company phone so was going back to original t-mob rom. But this cured my problem, phone now works fine with any rom.
Try it, get an original rom, flash back, then try anything.
Click to expand...
Click to collapse
http://forum.xda-developers.com/showpost.php?p=4799532&postcount=1218
http://forum.xda-developers.com/showpost.php?p=3521491&postcount=2
But i still have the problem with the strange behaviour of the dialler, When i press the phone button or try to dial a number i get a crash screen?
A blur image - and nothing is working in the dialler screen.
I did all what could help, reinstall the original rom, flash SPLL / Hard / radio etc.. but without suc6..
I have installed this one: cleanblack 6.5.2 - animelover and this is working fine, no dialer problems at all.....
Maybe the video dialler in the 3G is the problem for me, i will try this weekend the 2G - 230XXX version..
The 2G versions are working... and i try a few others also no problem, but i didn't like them....
My current is the best for me right now, clean and quick, i love the Clean Black rom 6.5.2 and animelover is building a new version...
Hoi Stranger,
Ok I'm trying to help you, because I had the same issue, I read something in the thread but I need to know if your problem only excist with the Insomnia-rom because I don't think it is a problem whith the Insomnia-rom.
My phone had the same issue with almost all the 3g rom except the original, that's the reason I couldn't bring the phone back for repair.
I tried several rom's wm6.1 and wm6.5 from randomelements, salvyC, Insomnia, Davideuck etc etc and all the 3g roms gave me a scrambled screen on the dialer, the solution I offered you to add a 3g dialer after flashing was working for me, I found the 3g dialer in the 4shared folder from NemanjaLo.
As I told you before, that is not a real solution, I thought the 3g version from Gullum didn't gave me a scrambled screen, but I'm not sure about that.
If you do have the same problems as I wrote above, I think you have to try the mtty procedure as randomelements suggested me.
You can find that here http://forum.xda-developers.com/showthread.php?t=390606 but plse be carefull otherwise your phone ends as a doorstop and I don't think it is worth it.
Rataplan
WOUW
Hi Rataplan,
Thx for your effort to help me in a way to get a 3G on my NIKI100.
This procedure is maybe to tricky for me! i will investigate...
FYI > with 3G roms from Salvy or Insomnia i have a scrambled screen on the dialer.
Tried the Insomnia 2G version and this rom is fine but to slow and i try a few others..
Finally i flash this one > the animelover - Clean Black 6.5.2 and I'm very happy with it. i will go with this one....
BTW > When i started with my niki100 at the beginning, i flashed with the sspl-1.16-nike.exe procedure the HardSpl 1.22 file and i never never, flashed this one >>hardspl-1.15mfg-nike.nbh, make this any sense? could this be the reason?
Thnx all.
When i start with my niki100, i flashed with the sspl-1.16-nike.exe procedure the HardSpl 1.22 file and i never never, flashed this one >>hardspl-1.15mfg-nike.nbh, make this any sense? could this be the reason?
Click to expand...
Click to collapse
You're right it is to tricky to use mtty that is the reason I didn't go for it to.
About flashing I don't think it make any sense because I start with hardspl-1.15mfg-nike.nbh and I had the same problem.
The only thing I know is that my Nike came from KPN but I don't know that is the problem.
I'm glad you found a rom that don't give you the problem.
Regards Rataplan
Maybe there is a change...
Rataplan said:
You're right it is to tricky to use mtty that is the reason I didn't go for it to.
About flashing I don't think it make any sense because I start with hardspl-1.15mfg-nike.nbh and I had the same problem.
The only thing I know is that my Nike came from KPN but I don't know that is the problem.
I'm glad you found a rom that don't give you the problem.
Regards Rataplan
Click to expand...
Click to collapse
That is funny, mine came from HI / KPN that could be the similarity, so we have a point, that might be all KPN / HI phones are fixed some how?
MTTY - Low Level Format would help?
Hi guys new to this site. I have seen lots of your threads, looks great.
I have a problem with htc hd2,
The phone is stuck on the screen lock, it's happened for the first time a week ago,
without a reason - my friend doesn't install any application or change something on the phone.
I did soft and hard rest and i change the rom to Energy.Leo.21916.Sense2.5 and it's the same annoying issue,
I have to mention that the Touchscreen respond without a problem - in SMS, menu and etc...
hope u could help me as fast as you can -
Thanks!
crunch2 said:
Hi guys new to this site. I have seen lots of your threads, looks great.
I have a problem with htc hd2,
The phone is stuck on the screen lock, it's happened for the first time a week ago,
without a reason - my friend doesn't install any application or change something on the phone.
I did soft and hard rest and i change the rom to Energy.Leo.21916.Sense2.5 and it's the same annoying issue,
I have to mention that the Touchscreen respond without a problem - in SMS, menu and etc...
hope u could help me as fast as you can -
Thanks!
Click to expand...
Click to collapse
Hello!
I had the same issue with Stock ROMs. Since I am using cooked ROM all my annoying not reasonable problems disappeared. Do not hesitate to flash more than one ROM to test them, also new RADIO is recommended.
Do not forget to use task29 before you flash a new ROM, and after flashing to make a hard reset. They can make miracles
also try the Energy 23699 or 29017 ROMs after task 29 & hard reset straight after new ROM has booted. Flash a recommended radio as suggested in first Energy post & see if it cures the problem.
I assume once unlock your screen functions normally ? if not & a full reflash with task29 & HardReset doesn't fix it you probably got touch screen hardware issue.
Hi all,
first from all, take my apologies for my english.
Now back to topic, I have a serious problem with my leo (T8585). It was started to freeze from a few weeks, after I changed ROM, but allways i was able to restet it. And now it froze for good. The screen is black and any buttons are not lighting. At the begining when i have removed battery and put it back, i could feel vibration at start but the screen didn't turn on. After several attemps I was able to run the device. And then, when i have tried downgrade radio from 2.15.50.14 to 2.14.50.04, it has showed me a error at the begin of process (0% of progress). I restarted device, but now I don't feel even vibration at start.
What can I do with this? Any ideas? Please, help me
Niko666 said:
Hi all,
first from all, take my apologies for my english.
Now back to topic, I have a serious problem with my leo (T8585). It was started to freeze from a few weeks, after I changed ROM, but allways i was able to restet it. And now it froze for good. The screen is black and any buttons are not lighting. At the begining when i have removed battery and put it back, i could feel vibration at start but the screen didn't turn on. After several attemps I was able to run the device. And then, when i have tried downgrade radio from 2.15.50.14 to 2.14.50.04, it has showed me a error at the begin of process (0% of progress). I restarted device, but now I don't feel even vibration at start.
What can I do with this? Any ideas? Please, help me
Click to expand...
Click to collapse
What ROM did you flash? Maybe it is caused by a bug in the ROM..
Try another different ROM.
I test almost all ROM here, and Radio 2.15 is the best radio so far.
BTW, you need HSPL to flash a Radio or if you dont have HSPL installed, you have to flash the full stock rom.
Cheers
Hey Guys,
I use a stable 10.1.3 CM since a year on my S2. Lately the camera started to quit qorking: "can't connect to camera".
About this time the torch (LED app) app did the same thing: "unfortunately torch has stopped".
What I did: do a full data/cache/dalvik cache erase: factory reset.
The camera/torch still malfunctioning.
Then flashed the last nightly CM: cm11-20140429, but still no luck.
Then reflashed the old stable version, maybe if it'll work, but noooo.
Do you have any suggestion to resolve this issue? My phone is 2 years old, never had a problem with it. Until now.
Shall I flash something via Odin?
Is there a "deeper" way to rewrite the camera/LED firmware/code/whatever?
(I was wondering if flashing these 2 CM versions the appropiate firmware's aren't rewritten)
Thanks in advance for the replies!
you can try more ROMs. However, there is a possibility that its a hardware issue.
The camera stopped working on my galaxy S1 after a factory reset.
I never did get it working again, and I tried about 4 different camera firmwares, flashing back to stock, and replaced the camera module too. Nothing worked.
knuckles1978 said:
The camera stopped working on my galaxy S1 after a factory reset.
I never did get it working again, and I tried about 4 different camera firmwares, flashing back to stock, and replaced the camera module too. Nothing worked.
Click to expand...
Click to collapse
Sorry to hear that.
I'm wondering now to replace the camera module as well.
I quickly tried this 3 ROM: aosb_kk_1.3.6_i9100, omni-4.4.4-20140728-i9100-NIGHTLY, Slim-i9100-4.4.2.build.5-OFFICIAL-4068, but with the same disappointig result: no camera, no LED.
If I first start LED/torch isntead of camera, the LED sometimes flashes:
I switch on, but nothing happens. Then switch it off: after a few sec delay the button will show the "off" state, and during this process the LED flashes for 1 sec.
I will try to revert to stock with odin, maybe...
The camera module is very easy to change. All you have to do is unplug it and plug a new one in.
You might be luckier than me.
knuckles1978 said:
The camera module is very easy to change. All you have to do is unplug it and plug a new one in.
You might be luckier than me.
Click to expand...
Click to collapse
Yes, but what if the same thing will appear? Ie. I'll change the camera module, but won't work.
Isn't there an easier way to check if surely the camera moduled is dead?
Btw I downgraded it to stock ROM via Odin, but camera still dead, so it is probably not a software error. :crying:
There's no way of telling if your camera module is broken without putting a new one in.
It didn't fix it for me though. And believe me when I say I spent a lot of time trying to figure it out.
Ok then.
Thank you very much for the support!