My wifi will not work. It use to be fine with radio 3.27 and dcd 2.3.2 but recently started acting really strange and now it cannot find any wifi signal. I loaded wififofum and no luck there either. The phone is still under warranty so I decided to load the VZW MR1 release. I have the MR1 laoded and the phone works still no WIFI - but I still have the nueSPL 2.47 loaded.
What do I need to do with this 2.47 bootloader to make sure when I warranty my phone that VZW doesn't try to deny me seeing the 2.47 bootloader?
I read the wiki but can't seem to grasp what I need to do in this case.
I think get a relocker but not sure and if that is right where do I find this relocker?
Thanks in advance
Errr I think I found what I was looking for in this link just after I posted.
http://forum.xda-developers.com/showthread.php?t=426041
Can someone confirm?
The relocker puts the stock bootloader on your phone, not the bootloader shipped with MR1. If you want the MR1 bootloader, you need to use the relocker, then flash the stock rom. After that, you need to run the MR1 update again. This will update your bootloader to 2.07 which is the MR1 bootloader.
gc14 said:
The relocker puts the stock bootloader on your phone, not the bootloader shipped with MR1. If you want the MR1 bootloader, you need to use the relocker, then flash the stock rom. After that, you need to run the MR1 update again. This will update your bootloader to 2.07 which is the MR1 bootloader.
Click to expand...
Click to collapse
Thanks GC14,
I tried running the relocker from the post I found. I used this 1Gig SD card last night to load nueSPL 2.47, it was no problem. When I follow the instructions with the relocker now I get card is not formatted to fat32, it is though, and if I select to go ahead and format I get an error that partition cannot be created. I can't get any further with the relocker I'm using.
So I get what you are saying, but I can get the relocker to work while on MR1. Not that I tried this before with a custom rom.
Thanks for the help
mc6800 said:
Thanks GC14,
I tried running the relocker from the post I found. I used this 1Gig SD card last night to load nueSPL 2.47, it was no problem. When I follow the instructions with the relocker now I get card is not formatted to fat32, it is though, and if I select to go ahead and format I get an error that partition cannot be created. I can't get any further with the relocker I'm using.
So I get what you are saying, but I can get the relocker to work while on MR1. Not that I tried this before with a custom rom.
Thanks for the help
Click to expand...
Click to collapse
Ohhh you're using nueRelocker? I'm talking about the original Titan Relocker. Flashes via USB and reverts you back to stock bootloader.
yes I just found what you are talking about.
So what would be my best approach?
I figured it out. I used the Actrve Sync Titan Relocker and then reloaded the MR1. Back in business for warranty now.
Related
Ok, I am going to get flamed I am sure... but I was trying to update to the 3.39 radio on my Tytan earlier today. I previously had the 3.35 radio and DCD's 3.12 ROM on there (using olipro2.40). I followed the directions on the forums best I could, and reflashed from 2.40 to 1.20 in the olipro. Now it is just stuck there. I cant reflash it to 2.4 or anything? Also everyone keeps talking about the RUU for the radio to flash it, but I have searched for two hours and cannot find a simple post about where I am supposed to find this program. Just a billion mentions of the RUU folder... which doesnt help me at all.
I just went ahead and reloaded the dcd 3.12 rom using olipro 1.20 and it looks to be booting, but this still doesnt help me with the radio issue... ( the SD card option will not work for me either.) Thanks for any help
Gaigebacca said:
Ok, I am going to get flamed I am sure... but I was trying to update to the 3.39 radio on my Tytan earlier today. I previously had the 3.35 radio and DCD's 3.12 ROM on there (using olipro2.40). I followed the directions on the forums best I could, and reflashed from 2.40 to 1.20 in the olipro. Now it is just stuck there. I cant reflash it to 2.4 or anything? Also everyone keeps talking about the RUU for the radio to flash it, but I have searched for two hours and cannot find a simple post about where I am supposed to find this program. Just a billion mentions of the RUU folder... which doesnt help me at all.
I just went ahead and reloaded the dcd 3.12 rom using olipro 1.20 and it looks to be booting, but this still doesnt help me with the radio issue... ( the SD card option will not work for me either.) Thanks for any help
Click to expand...
Click to collapse
RUU stands for Rom Update Utility. I have heard that flashing a radio ROM using a RUU with Olipro 2.4 is problematic. The SD card method is much better and easier. Can you get into bootloader? (power/camera/reset)
...
I have been able to get back to everything the way I had it before (as far as ROM and olipro version) and I can get into bootloader, but I dont have a compatible sd card.
Gaigebacca said:
I have been able to get back to everything the way I had it before (as far as ROM and olipro version) and I can get into bootloader, but I dont have a compatible sd card.
Click to expand...
Click to collapse
If its up and running as before I would buy/borrow a SD card and update your radio that way. Why can't you use the SD card method?
Ooops...just saw that you don't have a compatible card. The microSD card in your phone will work fine if its not SDHC.
I dont have a card reader or access to one in order to format the card and put the file in the root.
Gaigebacca said:
I dont have a card reader or access to one in order to format the card and put the file in the root.
Click to expand...
Click to collapse
Sorry I don't have another idea...I wouldn't attempt any further radio mods until you can get a SD card with the radio ROM on it. Too risky you might muck up your phone and at least now its working. If I remember correctly its the newest 3.x radios that were causing problems when being flashed with a RUU on Olipro 2.4. Perhaps one of the senior members has an idea.
I had to turn my Titan in for a replacement. Knowing about relocking breaking the usb port, I figured I'd do it anyway and just flash via the SD card. Well to my amazement I was able to relock and flash the OEM Radio and Software without and problems. Once it booted up Activesync connected and charge light came on.
Just figured I'd share since there is so much fear about relocking.
Went from 3.56 based ROM and 3.42.30 Radio back to OEM.
I had to turn my Titan in for a replacement. Knowing about relocking breaking the usb port, I figured I'd do it anyway and just flash via the SD card. Well to my amazement I was able to relock and flash the OEM Radio and Software without and problems. Once it booted up Activesync connected and charge light came on.
Just figured I'd share since there is so much fear about relocking.
Went from 3.56 based ROM and 3.42.30 Radio back to OEM.
Click to expand...
Click to collapse
I'm not sure what you mean about fear of relocking and relocking breaking the usb port.
The story on the street has always been.... DONT go from a GPS to a non-GPS radio. Something about how it will screw up the USB port.
http://forum.ppcgeeks.com/showthread.php?t=21953
Read first post
This is only a small example but I'm sure I could find more than 10 instances of this throughout threads. Including NO2Chem saying not to do it aswell.
The story on the street has always been.... DONT go from a GPS to a non-GPS radio. Something about how it will screw up the USB port.
Click to expand...
Click to collapse
I have never heard that story, nor have I ever had any problems going back and forth between GPS and non GPS radio.
While testing the new Sprint PRI way back when 3.49 came out (I'm on Verizon), and now testing the new Verizon update, I've had to go back to stock more times than I can count and have never ran into any issues.
May I ask where you found these rumors?
EDIT: Ahhh ppcgeeks...yeah don't really frequent those forums much. Not sure why n2c would say something like that because like I said, I've probably gone back and forth between GPS/Stock at least 15-20 times with no problems at all.
Read the first post in the link I gave you. Then you can do a search on downgrading issues to find more reports.
I know it can be done because I've done it on 2 different Titans now. I made the thread to help prove that it can be done so other arent so scared by the rumors as you call it.
gc14 said:
EDIT: Ahhh ppcgeeks...yeah don't really frequent those forums much. Not sure why n2c would say something like that because like I said, I've probably gone back and forth between GPS/Stock at least 15-20 times with no problems at all.
Click to expand...
Click to collapse
Exactly... I'm attempting to put the rumor to rest. Atleast as far as Verizon customers are concerned.
What SPL are you using before relocking to 1.06?
yep
Rom 2.09
Radio 1.30
yep
Rom 2.09
Radio 1.30
Click to expand...
Click to collapse
I think you misunderstood me....SPL = bootloader.
What bootloader are you using before relocking?
lllboredlll said:
yep
Rom 2.09
Radio 1.30
Click to expand...
Click to collapse
I am not sure if you answered his question. Which bootloader are you running, nueSPL or other?
I have heard some concern with reverting to non-GPS stock using the no2chem tools, but obviously there is no worry with the relocker and such.
gc14 said:
I think you misunderstood me....SPL = bootloader.
What bootloader are you using before relocking?
Click to expand...
Click to collapse
Sorry I misunderstood you. I was running 2.40 before taking it back to 1.06.
It gets hard to think straight with people flying in and out of my office every 5 seconds. I'll try to read a little more throughly next time.
Sorry I misunderstood you. I was running 2.40 before taking it back to 1.06.
Click to expand...
Click to collapse
In my encounters with going back and forth, this is what I've come up with (for Verizon users):
If using SPL 2.47, steps to relock are as follows:
- Install Olipro 2.40 via USB
- Install SPL 1.06 using Titan Relocker via USB
- Flash stock rom/radio
(DO NOT EVER USE nueSPL Relocker!!!)
To get back to SPL 2.47 from stock, all you need to do is run nueSPL Unlocker and use the microsd card to go from SPL 1.06 right to SPL 2.47, then flash a 3.x.x rom/radio. Going FROM SPL 1.06 TO SPL 2.47, SPL 2.40 is not needed.
If using SPL 2.40, steps to relock are as follows:
- Install SPL 1.06 using Titan Relocker via USB
- Flash stock rom/radio
To get back to SPL 2.40 from stock, all you need to do is run Olipro 2.40 via USB, then flash a 3.x.x rom/radio.
If using SPL 1.20, steps to relock are as follows:
- Install SPL 1.06 using Titan Relocker via USB
- Flash stock rom/radio
To get back to SPL 1.20 from stock, all you need to do is run TitanUnlocker via USB, then flash a 1.x.x rom/radio.
Now all there is left to do is link this to ppcgeeks and be done with the rumor. Thank you for your input....
gc14 said:
In my encounters with going back and forth, this is what I've come up with (for Verizon users):
If using SPL 2.47, steps to relock are as follows:
- Install Olipro 2.40 via USB
- Install SPL 1.06 using Titan Relocker via USB
- Flash stock rom/radio
(DO NOT EVER USE nueSPL Relocker!!!)
To get back to SPL 2.47 from stock, all you need to do is run nueSPL Unlocker and use the microsd card to go from SPL 1.06 right to SPL 2.47, then flash a 3.x.x rom/radio. Going FROM SPL 1.06 TO SPL 2.47, SPL 2.40 is not needed.
If using SPL 2.40, steps to relock are as follows:
- Install SPL 1.06 using Titan Relocker via USB
- Flash stock rom/radio
To get back to SPL 2.40 from stock, all you need to do is run Olipro 2.40 via USB, then flash a 3.x.x rom/radio.
If using SPL 1.20, steps to relock are as follows:
- Install SPL 1.06 using Titan Relocker via USB
- Flash stock rom/radio
To get back to SPL 1.20 from stock, all you need to do is run TitanUnlocker via USB, then flash a 1.x.x rom/radio.
Click to expand...
Click to collapse
I vote to have this added to the return to stock wiki. GC will you post?
How about USCC?
Brings me back to my previous question, GC (Previous Thread); How can I back-up the current ("Stock" for USCC) OS ROM and RADIO on my new Titan? It was discussed that it [dumping current ROM and Radio and then using dump to re-flash] couldn't be done. I wanted to do a ROM dump before flashing to DCD's so that I could revert to it if needed; also, so that I could re-flash to "stock" on my old unit before sending it back to USCC... however, I don't how to accomplish this, if at all possible to do so!
If anyone can guide me through this, I could upload the USCC "Stock" (for lack of a better word, since USCC has no actual "Stock" Roms) ROM and RADIO and make it available to other unfortunate USCC customers. I agree w/Serfboreds, and also vote to have this thread added to the "Return to Stock" Wiki.
Thanks, Guys!!
gc14 said:
I have never heard that story, nor have I ever had any problems going back and forth between GPS and non GPS radio.
While testing the new Sprint PRI way back when 3.49 came out (I'm on Verizon), and now testing the new Verizon update, I've had to go back to stock more times than I can count and have never ran into any issues.
May I ask where you found these rumors?
EDIT: Ahhh ppcgeeks...yeah don't really frequent those forums much. Not sure why n2c would say something like that because like I said, I've probably gone back and forth between GPS/Stock at least 15-20 times with no problems at all.
Click to expand...
Click to collapse
I think the issue lies with Sprint customers..... I personally have reflashed to stock at least 15-20 times.... from a GPS ROM and back.....
That is a very nice summary of steps for re-locking from various spl's and definately needs to be entered into the !iki.... If GC doesn't have time I'll do it when I get done here at the dentist.... booooooo....
I think the real issue was going from bootloader nueSPL 2.47 to a stock GPS rom caused problems. But because verizon customers dont have a stock gps rom to flash back to we go to a non-gps (1.XX) radio which does not cause the problem.
No2chem originally made the advice not to go back to a stock assuming stock included 2.XX or 3.XX radios. Once he was alerted to the fact that going back to stock 1.XX (i.e with verizon) did not cause a problem he modified his warning advice.
Once again, the warning is only valid for bootloader nueSPL 2.47
GC, does going from nueSPL 2.47 to olipro SPL 2.40 prior to relocking negate problems for everyone? I ask that question because I have refrained from moveing to 2.47 for fear of problems in the future. As far as I can see the benefits of 2.47 are marginal at best. But if I have a sure fire escape mechanism I might upgrade my bootloader at some stage
GC, does going from nueSPL 2.47 to olipro SPL 2.40 prior to relocking negate problems for everyone? I ask that question because I have refrained from moveing to 2.47 for fear of problems in the future. As far as I can see the benefits of 2.47 are marginal at best. But if I have a sure fire escape mechanism I might upgrade my bootloader at some stage
Click to expand...
Click to collapse
Yes, it negates the problems.
gc14 said:
Yes, it negates the problems.
Click to expand...
Click to collapse
Thanks dude. And I agree with Serfboreds that you should add this advice to your wiki. Very easy to understand and maps out all (most) of the possible relock escape routes.
Once again gc you are a font of wisdom.
ugh.... i can't keep up with all the misinformation anymore. If it works for you verizon users in your personal experience though good for you. I know for a fact it can cause problems. I'm starting to narrow it down to the original 3.35 leaked rom with GPS radio from sprint, but have no firm proof it's that narrow scope yet . Still have myself a brick from the GPS to pre-gps and I didn't use nueSPL Relocker thats for sure =P
For more info on the problem and others that experienced this "rumor" first hand go to ppcgeeks and search for "download mode"
I accidentally flashed the titan using olipro 1.2, and the new unlocker, and I cannot get past the verizon boot screen. This is a fresh new 6800. when I start it it says:
p DCAAXAM-4350
R 3.42.30
D 2.17
The bootloader screen says Tita100 spl-120.olipro
the only way I can flash is via the sd card. I cannot connect via activesync.
how do I fix it?
this is a warranty replacement, so I need to get this to work before I restore my old 6800 to factory settings, and return it to verizon
thanks
whiteblazer01 said:
I accidentally flashed the titan using olipro 1.2, and the new unlocker, and I cannot get past the verizon boot screen. This is a fresh new 6800. when I start it it says:
p DCAAXAM-4350
R 3.42.30
D 2.17
The bootloader screen says Tita100 spl-120.olipro
the only way I can flash is via the sd card. I cannot connect via activesync.
how do I fix it?
this is a warranty replacement, so I need to get this to work before I restore my old 6800 to factory settings, and return it to verizon
thanks
Click to expand...
Click to collapse
Can you not put the phone in bootloader mode (power+camera+reset) and connect via USB? Even though activesync doesn't see it, it's still possible for RUU updater to connect. I had a similar problem before. Try doing this and putting Hard_SPL 2.4 on it.
Look at section II on this wiki... it says if you have 1.20 olipro... flash to an older rom and radio... WIKI
Snippit.... " if it is 1.20 then you have the pre-GPS ROM bootloader and must first flash to one of the older ROMs and associated radio to boot into WM, get an ActiveSync connection and then upgrade to 2.40. "
nitro66215 said:
if it is 1.20 then you have the pre-GPS ROM bootloader and must first flash to one of the older ROMs and associated radio to boot into WM, get an ActiveSync connection and then upgrade to 2.40. "
Click to expand...
Click to collapse
Hes right, you need to load an old pre-GPS rom on your phone, then upgrade. I've had this happen myself.
Yes, this is what I saw too, however, all the roms I found on this page http://wiki.xda-developers.com/index.php?pagename=TitanOtherHome for the olipro 1.20 take me to an internal server error on fileshex.com. I can't find any rom file that I can actually download. Does anyone have a link to one or can you upload it? I suppose it doesn't matter which one it is, since I'm going to upgrade from there.
I just cooked an old 1.6.7 rom for you...wow did it bring back old memories.
Download 1.6.7 rom here: http://www.cinconet.org/titan/dcd 1.6.7 Rom.zip
Download 1.30.60 radio here: http://www.cinconet.org/titan/Titan Radio 1.30.60.zip
Put radio .nbh on the root of the card with a card reader. Force phone into bootloader and flash radio first. When it completes, remove the microsd card and replace the radio .nbh with the rom .nbh with the card reader. Insert the card again, force bootloader, and flash the rom. Remove the card and soft reset.
WOOOOOOOOT!!! it worked! Thanks gc14 for the files and awesome instructions!
Check your current bootloader
1. Hard reset your phone by holding down both softkeys, hitting reset, and pressing R (just for good measure)
2.
Hit POWER-CAMERA-RESET to check what version of bootloader you have installed.
* At the tri-colour bootscreen you will see the version number installed.
* if it is 1.04 or 1.06 then your Titan is locked and has the correct bootloader to flash to the stock ROM of your choice --> skip to step III
* if it is 1.20, 2.40, or 2.47 then your phone is unlocked with a third party bootloader and must relock your phone.
---------------------------------------------------------------------------
I have a Sprint HTC Mogul and have been shuffling through all the threads and still confused, sort of...
I am at the Tri-color screen and none of those version number matches mine.
on my tri-color screen it displays:
Tita100
SPL-2.06.0000
CPLD-9
i searched the board and found but it didnt give me a clear answer.
http://forum.xda-developers.com/showthread.php?t=284404
So far i have downloaded
Sprint Cab
dcd_titan_3.2.5.exe
Titan_Radio_ROM_3.42.40.exe
[OliPro MFG 2.40] (Hard SPL)
I'm hoping someone can help me figure this out, whether or not i need to downgrade/upgrade.
And Also was wondering what type of neat things i can do with the roms/kitchen im a total noob at this but trying to make sense of all of this.
Other Phone info:
rom Version 3.35.651.2
radio ver. 3.35.04
I'm *PRETTY SURE* that's just an updated version of the relocker SPL.
You should be able to flash back to a stock (non-GPS if I remember right) ROM from there.
I think what *MAY* have happened was the process got interrupted when you were unlocking?
so I *BELIEVE* your best bet is to return to stock, and unlock using SPL 2.40, then flashing on the new ROM/Radio
If I'm wrong, I'm sorry; It's early in the morning and I'm not quite awake enough to comprehend everything yet.
scrawnyb said:
flash back to a stock (non-GPS if I remember right) ROM from there.
so I *BELIEVE* your best bet is to return to stock, and unlock using SPL 2.40, then flashing on the new ROM/Radio
If I'm wrong, I'm sorry; It's early in the morning and I'm not quite awake enough to comprehend everything yet.
Click to expand...
Click to collapse
You are right on the money.......
that should be the stock bootloader for a stock gps rom.
if you want a custom rom you will need to unlock using 2.40 or 2.47.
kitchens just allow you to cook in apps that you want instead of installing them later. the problem is the install is permanent and they cannot be removed.
i prefer to flash a clean rom and install my apps later.
im pretty sure 2.06 is the temporary bootloader used by no2chem's nueSPL to ram with 2.47. if your bootloader shows 2.06 you will need to flash nueSPL again as it did not flash correctly. 2.07 is nueSPL Relocker.
i had not heard of anyone getting "stuck" in 2.06 and the op didn't mention he had tried flashing 2.47 or relocking.
i think you are correct though as i just checked and i am @ 2.07 (relocked).
lafester said:
i had not heard of anyone getting "stuck" in 2.06 and the op didn't mention he had tried flashing 2.47 or relocking.
i think you are correct though as i just checked and i am @ 2.07 (relocked).
Click to expand...
Click to collapse
it happened to me, although i didnt get stuck. it was flashed on a card that isnt flashing compatible (telus). i only noticed because it didnt reset itself like it said it should have. returned the card, got a San Disk, and reflashed nueSPL. this time it soft reset itself, and displayed the correct bootloader, 2.47.
I got stuck in 2.06 last night... earlier in the day I dropped my mogul in water and somehow cracked the screen at the same time. After drying everything out for 12 hours the phone came on with barely anything on the screen, I got the phone into bootloader (it was at 2.47) flashed a stock sprint rom, I immediately ran the nueSPL relocker (had to use my mobler to see the screen), after the relocker ran I was stuck in a 2.06 bootloader for some time, eventually I got out of the bootloader (not quite sure how... I flashed the stock sprint rom a few more times and mash some buttons) eventually I was able to run the relocker again and get my phone back to 2.07... a little bit of trouble but it was worth it now that I know I should have absolutely no problems getting a new (probably refurb) phone through TEP
scrawnyb said:
I'm *PRETTY SURE* that's just an updated version of the relocker SPL.
You should be able to flash back to a stock (non-GPS if I remember right) ROM from there.
I think what *MAY* have happened was the process got interrupted when you were unlocking?
so I *BELIEVE* your best bet is to return to stock, and unlock using SPL 2.40, then flashing on the new ROM/Radio
If I'm wrong, I'm sorry; It's early in the morning and I'm not quite awake enough to comprehend everything yet.
Click to expand...
Click to collapse
My phone is stock, i hadnt done anything to it yet. Im just unsure what to do because 2.06 was not shown at the step-by-step instructions.
so let me see if i understand what i need what to do....
flash the current rom, stock 2.06, with [OliPro MFG 2.40] (Hard SPL)
then run dcd_titan_3.2.5.exe and Titan_Radio_ROM_3.42.40.exe
then Sprint Cab??
Thanks for the replys
Ok so I just got my new device and I tried to update the bootloader from 1.04 to 2.47 with the new SPL with the .exe file form here. It restarted to flash and it froze. What do I do? I can't boot it to the OS and I can't update the bootloader. Please Hlep ASAP. I am stuck with SPL-104 and windows 6
Thanks.
if you can't get out of bootloader you may have to flash a stock non gps rom.
I am jsut flashing the bootloader. It had the original stock ROM on it.
lafester said:
if you can't get out of bootloader you may have to flash a stock non gps rom.
Click to expand...
Click to collapse
lafe is right.....flash a stock non-gps rom.......when you tried flashing the Nuespl 2.47 you did do it via SD card correct?
yes I did. I flashed it on a Non GPS stock VZW ROM
JukEboXAuDiO said:
yes I did. I flashed it on a Non GPS stock VZW ROM
Click to expand...
Click to collapse
try flashing another stock non gps rom and then try to upgrade the BL again....this time try Olipro 2.4.....somehow the BL didnt flash correctly the only way out is to flash the stock non-gps rom and the proceed...
I am using OliPro 2.4 from the DCD ROM thread. Is that the wrong one? Its stuck ont he loading screen
JukEboXAuDiO said:
I am using OliPro 2.4 from the DCD ROM thread. Is that the wrong one? Its stuck ont he loading screen
Click to expand...
Click to collapse
No....but above you posted 2.47.....you could try Nuespl 2.47 it is the latest and greatest...go over to PPCgeeks and grab it off my sig over there....it runs fom the SDcard....also what have you tried to get it back?.....if you have not already try a hard reset first.....
Here I will save you some time
http://forum.ppcgeeks.com/showthread.php?t=30561&highlight=hardspl+2.47
yes I have tried hard reset. It keeps going to hte bootloader. Ok i used Olipro 2.40 using hte cmd prompt and did what it told me to. When it restarted it got stuck on the updating page. Now its just stuck onthe loading page.
JukEboXAuDiO said:
yes I have tried hard reset. It keeps going to hte bootloader. Ok i used Olipro 2.40 using hte cmd prompt and did what it told me to. When it restarted it got stuck on the updating page. Now its just stuck onthe loading page.
Click to expand...
Click to collapse
Can you enter BL?
Yes. It loads to bootloader 1.04 and then goes to update from the SD Card and its stuck on the loading screen
JukEboXAuDiO said:
Yes. It loads to bootloader 1.04 and then goes to update from the SD Card and its stuck on the loading screen
Click to expand...
Click to collapse
ok let me make sure I understand.....you are in BL? which are trying to Un-lock with Olipro 2.4 or nuespl 2.47?
I am truing to unlock Olipro 2.4
I am a little confused also. Its been awhile since I flashed olipro 2.4... Aren't you supposed to pull usb at some point during the install?
you have to follow ALL of the instructions for the flash to work.
Nuespl 2.47 is much easier to use. I would still recommend reflashing the stock rom so you can put nuespl on your sd (providing it is 2gb or less).
if you are in bootloader you can just run the ruu and it will flash.
JukEboXAuDiO said:
I am truing to unlock Olipro 2.4
Click to expand...
Click to collapse
and you are trying to un-lock with Olipro 2.4 via sd.....if that is so then that is the problem....
flyers2114 said:
and you are trying to un-lock with Olipro 2.4 via sd.....if that is so then that is the problem....
Click to expand...
Click to collapse
Its stuck on the loading screen.
Can someone tell me where I can get the dman nbh file so I can re flash it back to what it should be so I can start over? All I have is a damn phone with no OS and bootloader 1.04.
JukEboXAuDiO said:
Can someone tell me where I can get the dman nbh file so I can re flash it back to what it should be so I can start over? All I have is a damn phone with no OS and bootloader 1.04.
Click to expand...
Click to collapse
1.04 is verizon's stock bootloader. Do these steps with an SD card. You can try using Verizon's stock OS/Radio... but it never works for me the first time.
1) Download the Sprint latest Rom Update. Right click the EXE file and extract the files.
2) Copy and rename Ruu_signed.nbh to TITAIMG.nbh on the storage card.
3) Put the card into the phone...Power+Camera+Reset. This will get into bootloader, and load the image.
When complete.... soft-reset.
DO NOT LET CUSTOMIZATIONS RUN!!!
When you get to the WM 6.1 screen and it asks for you to touch screen... DO NOTHING!!!
Remove SD card.
Connect your USB cable... get activesync to see it... Just tell it to cancel the syncronization.... Then run Olipro's Titan Unlocker 2.4.
When it's done getting 2.4 on it.... Copy the radio rom you want IE 3.42.50 to the SD card and flash away. Then the same for the new OS.
Thank you so much dude. I am gonna get this thing moving today. Thanks again!
JukEboXAuDiO said:
Thank you so much dude. I am gonna get this thing moving today. Thanks again!
Click to expand...
Click to collapse
No problem. It does get tricky, but once you get the hang of the concepts.... flashing back and forth is easy.