hi, guys.
I replaced my jasjam board with a herm100 (orange) one.
I tried to install my arabizer then it always said "can not run on this device".
I replaced the rom several times with several versions but still have the same problem, I think the problem is with imei so that the arabizer detect that it is not an imate device then refused to work.
plz can anyone help me solve this trouble !?
Related
hi everyone,
i have a huge problem. my rom flash for my i-mate (qtek 2020, mdaII, XDAII) hung during flashing (from 1.66 to 1.72 official i-mate rom) during the ce upgrade step 2. now my i-mate just hangs at the blue i-mate screen and i cant connect to it through pc anymore, get error 101. is there any way to get a good rom on it again (can i connect to the ppc by another way, other software or sd-card0 so it will work again, or does it have to be epaired at at a rapaircenter?
thnx, sorry for the bad english
See the pm i send you.
I have the same problem ...
plz tell me how u solve it
Best regards
plz help, i-mate dead after failed flash, error 101
Hi,
If all that happened was it hung during upgrade you can put the device into bootloader, power+d-pad+softreset button, and attempt upgrade again, but if OS you were upgrading to is corrupt causing the hang a new rom might be the way to go, www.buzzdev.net has everything i needed, or clubimate.com
I have same problem. My q-tec100 is reseting so I can' connect it to pc for flashing again. Please tel me what is bootloader and what is d-pad button so thad i can stop it from reset and connecting for flash
hi friends i have the same prob. somebody plz help me too
Hi,
I am trying to upgrade my orange m3100 to wm6 (Blackmajic), i have successfully upgraded the bootloader and radio version but when i come to upgrade the WM6 Rom i get error 260 which says check the cable. I have tried on 2 different pc's and different cables.
Basically the phone is connected but when you get past all the tick boxes and press update active sync drops out just before it updates.
Has anyone had this problem or do they know how to solve it?
I have also tried different Roms
Thanks for your help Jason
I have just tried to re flash the spl and the same thing is happening here now :-(
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#error
Tried these still no luck. Any help would be Much appriciated!
Try to read this... http://forum.xda-developers.com/showthread.php?t=299657
I had this same, and Olipro helps me
Got it sorted now!
Thanks a lot
Dear All,
i'm so sad to announce that my GENE100 is now at the repaire shop for fixing the problen that has been caused after following the post of "orefkov" in this thread
http://forum.xda-developers.com/showthread.php?t=360357&page=4
i don't know what to say to him regarding the very bad program that he mentioned there.
after i copied his program to my GENE's momory and run it, i got to the tri-color screen and no updates can be done for three days.
i searched many threads regarding this problem and i found this:
http://forum.xda-developers.com/showthread.php?t=360357&page=9
Friend,
this is the software only for flashing the ROM and unlock the ROM. you need an OS to install there. first flash the ROM with SPL then connect it with data cable, then just run RUU tool.exe, OS will automatically installed in your D600. this is not the problem.
Hi,
I have MDA Vario II, aka Herm300, aka Tytn ... My problem is that I've got "No GSM". So I got in forum and checked how to try to Fix it threads... So I tried by putting "Hard-SPL" and also I've tried to Upgrade "Radio", but every time when I start upgrade I recieve "Error 262" at 0%, I changed several Radio's but I had always same result. Also I've tried to downgrade to Official Rom of WM5 and it stops at 13% witn "Error 262" . So my Question is:
Is it possible that I have hardware problem not radio problem .
ATM it works fine with Schap's ROM as PDA and "No Gsm" Again ...
On Bootloader I got:
IPL-1.01
SPL-1.40.Olipro
If there is another solution that may help I'm open for advice.
classic brick...
wich one is the 262 error. (why to put the error number? write the entirely error!)
Dunno if it is brick, because I cant update with most of the roms and also I get error with every radio I try to update with ... I've tried with more than 10 radio's from the archive ...
P.S. I think it is Hardware problem + I got brick and because of the hardware problem i cant reinstal rom+radio or rom to repair brick problem ...
So wich one is the error??????
error 206 207 200768 i dont know...i have this issues too and the cprog.exe seems to be incompatible ... my cable hasnt a good contact to the usb plus the rom i had i didnt downgrade to wmoriginal in a few times...
-Mobile MDA Vario II - help my screen is four colours
Hi I have the same phone a T-Mobile MDA Vario II i ran unlock program HTC_Hermes_SIM_CID_Unlock_v3a - i must have run it wrong or something cause my phone has colours on the screen red green blue white with the ipl 1.01and spl 1.40 - it used to ipl 1.4 (ithink) and spl 2.14(i think) before i tried to run the hct_herm.....v3a.
Is my phone trashed or what can i do . when i plug in the usb cable the message at bottom goes from serial to usb but thats it - the active sysnc does not see the phone. help help help any advice welcome ( short of buy a new phone) this is my new phone i only got it a day ago.
tks
my dopod 818 pro(htc prophet g4) can't power on.
i need help to find the way to repair it.
i've looking in many pda forum, they talk about rewrite/reprogram the bootloader(i can't enter into bootloader mode).
they use something about jtag programmer, could anybody tell me how to use that thing(i'm newbi).
or is there anyway else to fix my problem???
I have the same problem with my Qtek S200 G4
this Jtag Pinout for HTC prohpet G4 ~ http://img.majidonline.com/show/183593/wizardjtagpinsis8.jpg
ROM Upgradation Failed
Dear All,
I was trying to upgrade my dopod 818 pro ROM version, but unfortunatly my connect breaked in the mid of process, due to that lost everything, even my previos OS too. and now i am unable to restart my mobile.whenever i am trying to on it, its showing only DOPOD on the disply may u plzz help me to recover my old settings?? i had already done the hard resett, but Result is NILL...
aadi1 said:
Dear All,
I was trying to upgrade my dopod 818 pro ROM version, but unfortunatly my connect breaked in the mid of process, due to that lost everything, even my previos OS too. and now i am unable to restart my mobile.whenever i am trying to on it, its showing only DOPOD on the disply may u plzz help me to recover my old settings?? i had already done the hard resett, but Result is NILL...
Click to expand...
Click to collapse
try reflash with the official rom