I just bought a USED TYTN Pro. The person i bought it from put his own rom on there. What I would like to know, is if I decide to change to a different COOKED rom, do I have to follow all steps in the newbie guide? Or can I skip ahead because he already has a cooked rom in there and may have already done some steps.
I tried to do the reset and i dont get a tricolor screen, i just get
R- 1.14.01.010
G- 32.50.7018.00h
B -3.62
VarioIII said:
I just bought a USED TYTN Pro. The person i bought it from put his own rom on there. What I would like to know, is if I decide to change to a different COOKED rom, do I have to follow all steps in the newbie guide? Or can I skip ahead because he already has a cooked rom in there and may have already done some steps.
I tried to do the reset and i dont get a tricolor screen, i just get
R- 1.14.01.010
G- 32.50.7018.00h
B -3.62
Click to expand...
Click to collapse
look at the stickies, the 4th one, (hard spl), look at the FAQ to enter bootloader
Get into your Bootloader (hold down camera+power buttons while inserting stylus for approximately 3-5 seconds). It should show SPL-3.28.Hard or SPL-3.29.Hard on the second line of text on your screen. If not then you didn't flash the new HardSPL, try again.
then go back and read some more
lupe
actually got to the screen and i see
Herm200 IPL-1.04
Herm200 SPL-1.40.Olipro
You should be able to get to the Tri-Color screen. What are you doing to get to the screen? Try holding the Power & Camera buttons and press reset. Keep holding the Power/Camera buttons until you get to the bootloader (tri-color) screen.
All you need to do is make sure the device is HardSPL. If it is, then you can flash other ROMs.
Looks like you've flashed Hard SPL once. If yes, from now on, you can directly proceed with the flashing of new ROMs right after download.
Regards,
Carty..
VarioIII said:
actually got to the screen and i see
Herm200 IPL-1.04
Herm200 SPL-1.40.Olipro
Click to expand...
Click to collapse
So its Hermes, not Kaiser
VarioIII said:
actually got to the screen and i see
Herm200 IPL-1.04
Herm200 SPL-1.40.Olipro
Click to expand...
Click to collapse
Your device as Hermes(TyTN),this topic reserved for Kaiser(TyTN_II,AT&T...)
is hermes as good as kaiser, should i find myself a kaiser?
VarioIII said:
is hermes as good as kaiser, should i find myself a kaiser?
Click to expand...
Click to collapse
Let me ask you. You don't know what you have bought?
Anyway this thread should me moved....
1. Go to the Hermes section
2. Search
Not as good by far
kristoff_sz said:
Let me ask you. You don't know what you have bought?
Anyway this thread should me moved....
Click to expand...
Click to collapse
VarioIII said:
is hermes as good as kaiser, should i find myself a kaiser?
Click to expand...
Click to collapse
VarioIII,
The Kaiser is much better in form and function. You should always know what you're getting yourself into PRIOR to purchase (A newb mistake). I'm sure Mods will move this... somewhere
Monderator intervention....
First, Moved this thread to the proper Forum.
Second, the questions you ask are subjective.
Yes, the Kaiser is a newer model and has additonal features but there are users who swear by the older models. In fact there are apps the work better on the Hermes and even the Wizard than the Kaiser (gotta love video driver issues!).
I would suggest you do some research, this forum is a great place to start. You've got a lot of reading to do, don't expect to be spoon-fed here check the links in my signature so keep your self out of trouble (especially the What is XDA-Devs).
Hahaha
This is an amazing thread...
I dont know the IPL and SPL that kaiser gots!
but SPL 1.40.Olipro and
IPL 1.04
Sound s to me like a Hermes....
But tell us...
Is this your machine?
1.-
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
or this
2.-
So... #1 or #2
i got the hermes 200, just flashed with some manilla rom, works great. just 5 questions i couldnt find answers to;
1)Had a nokia n95, exported phonebook to .CSV and .TXT, how do i get that into this phone?
2)I was shown the gps receiver working, but since i flashed dont know how to get satellite aquisition
3) Anyway i can use mp3 for Text alert and Alarm?
4)(Manila2D) V.20 Build 20921 by PhamQuang is what im using, is it the best for manilla 2d?
5) Where can i get voip sw to work with the above rom
THANKS in ADVANCE
1st, you need Hard SPL V7 on your Hermes to be safest when flashing new roms...
1. Manually enter. You could also bluetooth across if the contacts are still in the n95.
2. Pair the receiver. then go to advanced. assign a serial port ( I use 4). Next, at the bottom of the screen, pick com ports. Pick set new then highlight the GPS receiver. Assign port number you want (some ports aren't available as the Hermes uses these.). Open the GPS software you use (I use Tomtom) and select the port you are using. Violla. Good to go.
3. There are some apps available but I can't remember what they're called, do a search.
4. Don't use Manilla.
5. Don't use voip.
You need to search as these things have been answered. try a combination of keywords if you don't get a hit straight away.
Cheers...
Related
Hi to all
Its possible extract a rom from a tytn and install this rom so other tytn???
or we must use the ship version???
if it is possible how can we extract a rom and how we can convert it to flashable rom???
Thx
Short answer: It is not possible yet, you must wait for a shipped version.
Long answer: A ROM consists of 7 parts:
1. Extended ROM
2. OS Image
3. IPL (part of bootloader)
4. SPL (part of bootloader)
5. Splash screen
6. HTC Logo (normally uses the same image as the splash screen)
7. GSM radio code
You can dump the original rom, but only the things contained in the FLASH will be dumped, this does not include the IPL, SPL, splash and radio parts, so its unuseful for flashing it back.
I've updated the wiki with this answer, see here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeFAQ
Thx
For the Vv (very very) clear answer...
Please Help
Hey pof.
I was wondering if you could point me in the right direction with my problem.
I've tried to upgrade my HTC Tytn original ROM to JasJam ROM , right at the end (99%) the updating software stoped , gave me an error and restarted the computer. Now all i see on my tytn is dots with mixed colours all over the screen(not even a tri-color mode) it looks like a broken tv. Now i can't even sync it with my PC to install old ROM. Can't do anything with it now. the reason for this i guess is a ROM update that wasn't completed.
I've tried to use bootloader but it didn't give an 'USB' option. just com1 and com2.
Please help. Iam really desperate
slava888 said:
I've tried to use bootloader but it didn't give an 'USB' option. just com1 and com2.
Click to expand...
Click to collapse
Does it look like this?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
1) try SD card flashing:
http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing
2) If it doesn't work, put the unit in bootloader mode, disable activesync usb on your computer (Connection settings -> disable USB connection) and try to flash a ROM using the usual method.
Other than this... I can only tell you trying to get a repair under warranty
Hey pof. Thanks for the quick reply.
That is exactly how it looks !
Listen, somehow i've managed to get in to bootloader.
It shows on top:
HERM200
IPL-1.01
HERM200
SPL-1.04
I've tried to do the SD Rom update but it doesn't work. Just shows me the same bootloader screen with those two messages(above). Pushing the powere button doesn't do anything
The bootloader update didn't work either. when i typed in "set 14 0" it said "Write Nand Success" but when i soft reseted it , it still gave me that screen.
Any ideas what i can do? other then send it for repairs.
Thanks again.
Hope to hear from u soon.................iam freaking out here
Just tried SDCardFlashing with different ROM files.
With the original ROM it does not do anything (stays in the bootloader screen)
With JasJam (that's the one i've tried to install) it show "checking..." message on screen , but does not do anthing.............been like that for 10 minutes.
Can't believe i've screwed up so bad
At least bootloader is still "intact", the right NBH file should be the one matching your CID, assuming that you have a TyTN it should be the TyTN 1.18 rom.
If you can go into bootloader and send commands using mtty check your CID with command "info 2".
Also try to do a rom upgrade using the usual proces while the unit is connected in bootloader mode and activesync usb disabled, click on RomUpgradeUt.exe, then Next ,next, next... if it fails tell me which error you get and where.
Hey Pof.
when i try "info 2" command , it just hangs without any output. and i can no longer type in commands.
I've tried to run RomUpgradeUt.exe
This produced ERROR[222]: DEVICE NOT RESPONDING. I get it at the end , after the updater asks me for final confirmation.
...............................
Read this thread, from post #11 until the end
http://forum.xda-developers.com/showthread.php?t=278025
Try to put USB monitor (instructions on post #11) and see if you get any output from the device... attach the USB capture here if you want, I can have a look at it.
Hey Pof.
Did everything like you said.
Here is the output.
P.S: didn't allow me to upload WinAce archived files so i upload the text file, its pretty small.
slava888 said:
Did everything like you said.
Here is the output.
Click to expand...
Click to collapse
The RUU sends "task 32 ; info 2 ; info 3" commands to bootloader, but you get no output from it, I think it's screwed because none of the three commands is answered by your device.
Normally, task 32 should return the seclevel, usually 0xFF ; info 2 should return the CID (in TyTN it is QTEK_001) and info 3 should return the block to calculate the dynamic password to be able to use wdatah command. Without wdatah you cannot flash
Do you have warranty on your device?
Yes its still under waranty , i purchased the device couple of weeks ago. Iam going to call them today.
Can you please advice me on what should i tell to HTC customer support ppl as to why this whole mess happend to my handheld?
Just wanted to tell you that i really appreciate your effort. Thank you for everything.
slava888 said:
Can you please advice me on what should i tell to HTC customer support ppl as to why this whole mess happend to my handheld?
Click to expand...
Click to collapse
HTC has not "officially" released any rom for the hermes yet, the tytn rom we have on the ftp is leaked from dangaard NL, so you cannot say you've been trying to upgrade the rom because they will tell you there are no rom upgrades available yet.
If you are not in a hurry to have your phone back you can wait until they release a ROM upgrade and then tell them the "truth"... but i don't know if they will be able to see that you flashed Imate ROM and not HTC ROM (and flashing another brand's rom voids your warranty). If they don't notice it, the repair should be under warranty and no charges for you.
If you are in hurry, just tell them you tried to flash the imate jasjam rom (downloaded from imate ftp) and phone screwed, they will charge you some money to repair / flash back the original htc rom on your device and return it to you, but you'll have to pay because this is not covered by the warranty.
I don't know how much will they charge you for this, but you can explain them by phone and ask...
Hi all
I was sick waiting for cid unlock for (t-mobile ameo – dutch),
So I used modified tools from http://forum.xda-developers.com/showthread.php?t=299154
to force writing Windows.nb ,just changed the bat file to write the new OS and it worked, my Athena now has English OS from RUU_Athena_HTC_WWE_1.25.405.2_1.38.00
the modified tool is here
http://www.aczua.com/Athena_upgrade.rar
(use @ your own risk)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
wow...
this is incredible news!!!
can someone else confirm this???
time for wm6 action on ameo!!!
do you mind giving me the link to the rom to uploaded ???
fallenczar said:
wow...
this is incredible news!!!
can someone else confirm this???
time for wm6 action on ameo!!!
do you mind giving me the link to the rom to uploaded ???
Click to expand...
Click to collapse
sorry not yet, needs the wm6 XIP but wm5 cooking can happen
can this remove the sim/network lock as well?
So then the question is: What is the best ROM out there... the AMEO, Dopod or HTC?
lawbet7eb, can i first thank you for the doing this for the ameo/dopod/advantage communities. Could you please inform me or point me to the correct link which will show me how to use this tool, thank-you.
fallenczar said:
wow...
this is incredible news!!!
can someone else confirm this???
time for wm6 action on ameo!!!
do you mind giving me the link to the rom to uploaded ???
Click to expand...
Click to collapse
Thanks for the link fallenczar. This is great news indeed. Is this now officially CID unlocked? Or just a way of forcing a flashing of another ROM?
CAN U please provide with more deatils of how did u do it !!! we all appretiate it hoop that u can say how to upgrade to english waited something like this for a long time THANKS ALOT !!!
Its NOT Cid unlocked, it uses some utilities by itsme to write directly to the NAND flash that the OS is stored in
Is it possible flashing the device fromout the bootloader screen? Or must the device be connected en synched using activesync?
Regards
Vince
Can anyone modify the files to flash radio..I know that if we flash POF's 1.16 Radio of Hermes, it makes the device Super CID..
Tried, but doesn't work...pls others post the results
OK..could flash..one needs to first hard Reset yr PPC, then install cert,rapi cabs, then swith off for 10 sec and reboot, then async run the batch file..works..great discovery..
hdubli said:
OK..could flash..one needs to first hard Reset yr PPC, then install cert,rapi cabs, then swith off for 10 sec and reboot, then async run the batch file..works..great discovery..
Click to expand...
Click to collapse
what do you mean by great discovery?..do you manage to flash the radio?
you cant flash radio like this.
Can someone add the procedure to the wiki and does it mean that now i can flash my english ameo with a unbranded htc athena rom ?
Take it easy friends...it needs to be safe for all to use..
Guys I'm all for progress and this going in the right direction, but it is NOT properly CID unlocked. Be very careful peeps before someone bricks their device!
This is why we have set up the Athena project, to avoid this and get some pro's to help us.
I hope everyone agrees that Midget_1990 should be on board as he is experienced with ROM cooking and the likes for the VGA 3G Universal and is the only xda developer who has showed an active interest in our forum.
if you read the link from arti upgrade you will get the picture,
it could be risky to force OS with this procedure as we all know that there is a problem with athena cutting connection, read this:-
http://forum.xda-developers.com/showthread.php?t=298259
if athena cuts and upgrade was not complete, u can reflash with original rom.
another thing, this upgrades only the OS, not radio, ipl spl...etc, AND IT WILL NOT MAKE ATHENA CID-UNLOCKED
i believe we all should join The Athena Project @ http://forum.xda-developers.com/showthread.php?t=311651
there is nothing like SuperCID Athena
I heard from somebody that there was a way to CID unlock an Ameo with the old original radio ROM from T-Mobile. You had to flash back to an early Radio, then you could remove CID lock (or the early radio didnt have a CID lock in it). Then you could flash a normal Athena Radio back into it. He was vague about it but promised to email me the full procedure. He never did.
Is this worth looking into?
thanks to lawbet..now i have a full english version rom...
i first attempt was stucked..but then tried again using hdubli instruction...i`m happy right now untill we get cid unlock...
cheers..
Hi, I think wm6 or 6.1 roms have some common problems in all roms which can be discussed here.
I begin first :
I used to change rom by jumpspl and I didn't want hardspl ( i was spl 2.20)
but for the last cloudyfa rom i saw everywhere to use hardspl so i thought there will be problems if i don't do that
but after i hardspled my device to g3.4pda.... and used the new rom ,my device stays about 20 seconds on the spl showing page after each soft reset .
i remember this page went so quickly before that i couldn't read all of the numbers (ipl,spl,os,radio) in it
so the sof reset process takes a lot more time now.
i wanna ask if it is because of the new rom or the new cracked hardspl ?
and if it is the hardspl how can i change it back ?
To change back the HardSPL process, you will need to use an operator ROM such as the Orange WM5 ROM (it's available on the FTP, I'll find a link when I can).
You shouldn't need to HardSPL to flash a ROM, it is just more reliable that JumpSPL or SoftSPL in that once you've done it, it won't revert very easily.
oh my god . that's almost a bad news
i remember having a nvid rom which was used for the previous upgrade way.
i will use it when i wanna do my next rom upgrade.
so you think the spl is the reason for my 20s start up delay ?
by the way thank you as always for your kind answers.
i remember having a nvid rom which was used for the previous upgrade way.
Click to expand...
Click to collapse
I think the ROM can not be NVID as I don't think it'll reflash the SPL. I would recommend a vendor ROM as it will work (I have tried it).
so you think the spl is the reason for my 20s start up delay ?
Click to expand...
Click to collapse
I've only just noticed that delay, but probably something to do with the SPL.
ok so I will use one of the original jamin roms I have.
once again thanks and pardon me for another question :
since I am using roms above wm5 like 6 and 6.1 the batterystatus program wont do the cpuscaler thing which i used perfectly before.
I asked and tried a lot but could not get it to work. even tried to use XCPUScalar2007_v3-03 but it wanted a lot of testingand ...
I saw that you wrote @286 in signature , what do you use ?
if it's batterystatus can you give me your settings files
I was using Battery status (I use the 1.05 beta version, not sure if that helps) and it works flawlessly.
ok can you show me your setting for the two pages for overclocking or at least your xml setting file ?
another thing :
in the new cloudyfa rom the the bluetooth sound of the caller is much louder and i think that even the quality of the BT stereo music is higher,
but the volume of the caller sound from the device itself is significantly lower than before.
i remember that the previous builds had some tweak for the volume during the call, but in this one its not mentioned...
is this the reason ?
I've just flashed a ROM, so I will have to set up Battery status first and then I shall post screen shots.
I would suggest speaking to Cloudyfa, or putting a post in the ROM thread as it will probably get fixed faster.
useful info..
i'm really interested with the overclock..
i'll be watchin this thread..
Finally got around to it! Here are the screenshots. This is using BatteryStatus 1.05beta.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
great..
i'll try this soon i get back home
l3v5y said:
Finally got around to it! Here are the screenshots. This is using BatteryStatus 1.05beta.
Click to expand...
Click to collapse
thanks and I did all the settings on your pic.
but it stays like this:
i remember when it worked, there was another figure for cpu load near clock : 195/40
I think you need to enable the task manager feature, although I can look at that in more detail later...
Newbeeeeee Stuck with sound problem after upgrade
Hi,
I am newbee on this ROM upgrade issue. I tried to follow the upgrade guide as much as i could but after installing 3 or 4 WM6.1 ROM packages i fail to rectify one problem. That is the sound issue. Now even the midi tones set for the Ringing come with cutting. With increasing the volume it increases but this was not happening when i had the original WM5 installed. I fail to understand what step i am missing or there is some codec problem which i am failing to understand.
My steps are:-
(1) Hard SPL the device when connected with PC.
(2) Run the ROM_UpdateUtility_G4..... and wait
(3) Once the device shows 100% and PC gives success i remove the device its battery for 3sec and then softy reset it.
am i missing some important step
Sorry
Try this!
naumanx said:
Hi,
I am newbee on this ROM upgrade issue. I tried to follow the upgrade guide as much as i could but after installing 3 or 4 WM6.1 ROM packages i fail to rectify one problem. That is the sound issue. Now even the midi tones set for the Ringing come with cutting. With increasing the volume it increases but this was not happening when i had the original WM5 installed. I fail to understand what step i am missing or there is some codec problem which i am failing to understand.
My steps are:-
(1) Hard SPL the device when connected with PC.
(2) Run the ROM_UpdateUtility_G4..... and wait
(3) Once the device shows 100% and PC gives success i remove the device its battery for 3sec and then softy reset it.
am i missing some important step
Sorry
Click to expand...
Click to collapse
I think you should try to hard reset your device after flashing the ROM instead of just a soft reset.
Check out the WIKI page for prophet for how to hard reset your device!
http://wiki.xda-developers.com/index.php?pagename=HTC_Prophet
Good luck!
// Ohamn
Good pardon but my Englishman is a villain like that that a translator uses .. I promise to study mas, good update my spl/ipl to 3.xx to install one wm6 work edition, but when my htc cingular finishes 8125 murio it(he,she) does not enter in bootloader does not answer please I ask you for help they have said to me that for the SD it is possible to install but I prefer consulting with the experts..
Probably the topic already was but my Englishman is a villain like that that I ask for the corresponding excuses.
Chile Becomes present. Urgent course of English...
I got cingular 8125 IPL/SPL problem
Please someone help me! My Cingular 8125 has died after an updat Wm6.1 to WM6.5, I was trying to install. All I got now is this screen. What should I have to do? (Sou brasileiro, estava tentando atualizar o wm6.1 p/ o wm6.5 e aconteceu isto, queria saber qual proggram devo instalar p/ reativar a comunicaçao c/ o Activesync?)
IPL 2.25.0001
SPL 2.25.0001
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Download and install this "ROM"
Hi - i am in great trouble for long time... can you help !!!
MY rgb screen says IPL: 1.05 and SPL 3.08 (no more info on RGB Screen, only also USB when conn.) then when booting it shortly shows "Windows 6.1 SNN edition windows mobile" and then it cont. to next screen that freeze with this" IPL 1.05, SPL 3.08, GSM 02.25.11, OS 1.5.4.2, and text "Some Things Last Forever" and "From Button With Love"
it all started because i tried many things to upgrade from wm5 to wm6 and now im stucked with phone - can anyone figure out or is it bricked now - best regards, Peter
ps i will donate if help to work again - i am in Europe, Denmark but phone is from California.
Is the phone from Cingular or T-mobile?
You can try a hard reset by pressing and holding the CommManager key and the Voice dial key while doing a soft reset.
or
Download one of the listed ROMs.
Turn the phone off, press and hold the camera key, now insert the USB data cable, you must continue to press and hold the camera key until you see the boot loader screen.
On the boot loader screen you will see IPL SPL and on the bottom of the screen USB.
Now flash the ROM.
Cingular ROM
LINK ONE
LINK TWO
T-Mobile ROM
LINK ONE
LINK TWO
AFTER FLASH IPL/SPL MY DEVICE IS BOOT IPL 3.08.1, SPL 2.18.0001 AND AFTER RESTART IS DEAD.
HOW TO FLASH BACK IPL/SPL TO 2.18.0001?
PLEASE HELP!
my device T-Mobile MDA(US)
If the phone doesn’t boot at all, I don’t know how or if it can be fixed.
-MyHTC- said:
You can try a hard reset by pressing and holding the CommManager key and the Voice dial key while doing a soft reset.
or
Download one of the listed ROMs.
Turn the phone off, press and hold the camera key, now insert the USB data cable, you must continue to press and hold the camera key until you see the boot loader screen.
On the boot loader screen you will see IPL SPL and on the bottom of the screen USB.
Now flash the ROM.
Cingular ROM
LINK ONE
LINK TWO
T-Mobile ROM
LINK ONE
LINK TWO
Click to expand...
Click to collapse
Thanks MyHTC !
Do you think you can upload "Cingular ROM" also on www.4shared.com...because on rapidshare it seems that I have problem downloading ... (I am at the office now...and it looks like there are others that are downloading with the same IP)
Cingular 8125 bootloader screen
Hi HTC.... i am working on your given methods as my Cingular Phone is also stuck on green screen showing IPL/SPL/GSM/and OS
i am trying to connect it with computer so i can flash its ROM but my Wizard Service Tool say that device is not connected... can you help me for this....?
I love my this phone my lots of information is in it... important data will be lost if i couldn't solve it... please help me....
Regards
Sorry but if your phone can’t boot to window you won’t be able to recover your data.
-MyHTC- said:
Turn the phone off, press and hold the camera key, now insert the USB data cable, you must continue to press and hold the camera key until you see the boot loader screen.
On the boot loader screen you will see IPL SPL and on the bottom of the screen USB.
Now flash the ROM.
Click to expand...
Click to collapse
The instructions above will help you flash your phone but they won’t help you recover data.
zkako said:
Good pardon but my Englishman is a villain like that that a translator uses .. I promise to study mas, good update my spl/ipl to 3.xx to install one wm6 work edition, but when my htc cingular finishes 8125 murio it(he,she) does not enter in bootloader does not answer please I ask you for help they have said to me that for the SD it is possible to install but I prefer consulting with the experts..
Probably the topic already was but my Englishman is a villain like that that I ask for the corresponding excuses.
Chile Becomes present. Urgent course of English...
Click to expand...
Click to collapse
The translation is very bad. I would suggest that anyone posting questions through a translator should also include the question in their native language. That way, if the translation is bad, perhaps someone can offer an improved version.
In this case, I think the problem is either that there are eels in your hovercraft, or perhaps you have a G4 and bricked it by loading G3's IPL/SPL.
I don't know how to solve the first problem, but the second cannot be solved with the normal tools at hand. Good pardon.
Hi
Thank you for this post!
Even dough have been 3 and a half years since you posted this, I use it, and maybe I wouldn't say more than 10x. But as II have seen it is posted in the same day as mybday and your avatar is one of the photos I like to use with my HaX nick. So, thanks -MyHTC!
:good:
1. Possibility to choose one from several NBH files. Files should be placed in one folder with utility.
2. Possibility to choose the way (option) of flashing
3. Possibility to get NBH file info (Modification date, Model ID, CID, Version, Lang, Chunk size)
Regular RUU (Task 28)
Hard Reset is performed straight after flashing automatically (good for NBH containing OS section)
Custom RUU (Task 00)
to install only radio roms without performing hard-reset.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Custom ROMs can be flashed if HSPL is installed to device (no idea when it will be ready or published)
Utility was tested with official Titan roms - thanks to AndrewSh and Feropont
ATTENTION! Unskilled interference to your phone's OS can totally crash your device.
If you understand what are you going to do - go ahead.
No warranty.... use on your own risk.
thanks alot barin.
Thank you buddy, good job
Excellent and very convenient tool - thank you very much my friend.
For those who will use it with official nbh - remember that process is "freezing" at 5% - re-flashing spl - so don't worry - just wait with patience. It will continue faster after spl update.
Also remind - how to get to bootloader mode - switch the device off, press and hold Volume Up and Down simultaneously and turn the device on. Then connect USB cable.
Titan Advanced RUU and nbh file should be placed in one folder on your PC.
Thank you, good job
Thank you , good job
Thank you so much!!!!
hi, sorry for the question but with this tool, does it mean that i can flash a taiwan ROM on my european htc titan ? or is it still restricted to the only ROMs from europe ?
xtrememanix, this tool is just Update utility - flasher. You should wait for HSPL to flash another region to your device.
Man... seem that HSPL for HTC Gen2 is coming!!!! LOL.
nhathoa said:
Man... seem that HSPL for HTC Gen2 is coming!!!! LOL.
Click to expand...
Click to collapse
No info, dude, if it's coming or not.
Actually Titan Advanced RUU has no connection to HSPL discussions ans speculations. It's the same situation as with OsBuilder - current public version supports WMSTORE (second gen devices rom structure) but there's no way to flash custom second gen roms.
nice tool..thx4that....yeah thats right..building a rom is not the problem...the bootloader is it..hmm...someone here can contact cotulla or other people from the dft team 4 some news?..
Sent from my OMNIA7 using Board Express
So with task28, when it finish flashing ROM to my Titan, and just wait to config into WP7? Don't need hard reset anytime by myself?
Little confusing
My ways of flashing ROM:
Using RUU to flash
After finish. Turn off device and Hard reset it.
With Task28 i dont have to Hardreset anymore, right?
-=Barin=- said:
Regular RUU (Task 28)
Hard Reset is performed straight after flashing automatically
Click to expand...
Click to collapse
GinCifer, if you have a desperate wish to perform one more hard reset manually - go ahead. But it's not necessary.
AndrewSh said:
GinCifer, if you have a desperate wish to perform one more hard reset manually - go ahead. But it's not necessary.
Click to expand...
Click to collapse
Thanks for confirming me
I'm kind of confusing with task29 in WinMo device a little
any chance for a version of this for the HTC Radar?
sh4d0w86, I will point Barin on your request today....
AndrewSh said:
sh4d0w86, I will point Barin on your request today....
Click to expand...
Click to collapse
thanks, AndrewSh. I am willing to test with my HTC Radar.
sh4d0w86 said:
thanks, AndrewSh. I am willing to test with my HTC Radar.
Click to expand...
Click to collapse
Barin offered you to try this Titan flasher with your Radar - it will work.
AndrewSh said:
Barin offered you to try this Titan flasher with your Radar - it will work.
Click to expand...
Click to collapse
tried it. it stopped at 5% on phone, 6% on PC. must be my Radar... tried using a Radar RUU with same luck. my Radar won't boot out of the Bootloader. had ordered a y-cable, was going to try Goldcard method.