Hey all,
So I've got a small issue. I've got a Verizon XV6800 with the MR1 Rom WM6.1, Valhalla GPS server, 3.42.50 Radio.
Internet connection sharing is not working at this point. I've gone through the winmodem and internet connection sharing cab installs, registry edits, etc. None seem to help.
I previously had a ATT tilt 8925 and had no issues whatsoever tethering it to my mac by just pairing the phone, selecting to "Using a direct Higher speed connection to reach your ISP". Starting Internet Sharing on the phone, selecting Bluetooth PAN & the default data connection, then selecting connect. Then selecting "Connect to network" On the mac through the my phone listed in the bluetooth connections. That simple.
Having installed the "Internet Sharing" cab onto the phone. Internet sharing appears to work, but the phone does not advertise this service, like the ATT tilt did on ATT's network.
I've also tried a few registry edits, and used all variations of modem scripts, and got all the dialup info from verizon directly (so I know it was right ) but could not get dialup to work either. Usually not detecting a carrier, other times lockups.
I truely want to get the bluetooth-PAN working again as it did on my tilt. Anyone have this working on the MAc with a XV6800 on verizon?
i did have it working before. I'm wondering if you might be more successful with a custom rom. Verizon installs software (at least previous roms, I haven't tested the MR1 rom) that reverts reg edits and keeps it working like VzW wants it to. This could be causing problems. First check after a soft-reset to make sure your reg edits still exist.
Also I'm sure you've tried this be in Leopard's bluetooth setup delete the phone and try again. You need to select the type of device as any device in order for leopard to see it. Can you connect the device to your mac? Try that first. If you get a BT connection non-internet connection and you change your settings delete the phone and try again. I forget some of the setting I used. Also Engadget had a how to article for BT pan using the xv6700 and Tiger most of the information is still useful. It's a couple years old so you might have a hard time finding it.
Hope some of that helps.
Cycomachead said:
i did have it working before. I'm wondering if you might be more successful with a custom rom. Verizon installs software (at least previous roms, I haven't tested the MR1 rom) that reverts reg edits and keeps it working like VzW wants it to. This could be causing problems. First check after a soft-reset to make sure your reg edits still exist.
Also I'm sure you've tried this be in Leopard's bluetooth setup delete the phone and try again. You need to select the type of device as any device in order for leopard to see it. Can you connect the device to your mac? Try that first. If you get a BT connection non-internet connection and you change your settings delete the phone and try again. I forget some of the setting I used. Also Engadget had a how to article for BT pan using the xv6700 and Tiger most of the information is still useful. It's a couple years old so you might have a hard time finding it.
Hope some of that helps.
Click to expand...
Click to collapse
As mentioned, I have tried a ton of different methods to try and use the data connection, from using dialup settings, to trying to get the Bluetooth Pan working. I've removed and re-paired the device from my mac, flashed roms, hacked away at the registry a ton of times. Nothing seems to give so far.
I've got one more suggestion, found here: http://forum.xda-developers.com/showpost.php?p=1794133&postcount=29
I'm going to give this a shot tomorrow and will let you know how it goes.
Eponymous069 said:
Hey all,
So I've got a small issue. I've got a Verizon XV6800 with the MR1 Rom WM6.1, Valhalla GPS server, 3.42.50 Radio.
Internet connection sharing is not working at this point. I've gone through the winmodem and internet connection sharing cab installs, registry edits, etc. None seem to help.
I previously had a ATT tilt 8925 and had no issues whatsoever tethering it to my mac by just pairing the phone, selecting to "Using a direct Higher speed connection to reach your ISP". Starting Internet Sharing on the phone, selecting Bluetooth PAN & the default data connection, then selecting connect. Then selecting "Connect to network" On the mac through the my phone listed in the bluetooth connections. That simple.
Having installed the "Internet Sharing" cab onto the phone. Internet sharing appears to work, but the phone does not advertise this service, like the ATT tilt did on ATT's network.
Click to expand...
Click to collapse
I was wondering if you be gracious enough to share the Internet sharing CAB i only need to get it to work thought the USB cable and on a windows box, and from what im getting you got that far... JUST not working on a mac...
if thats the case, i would be ever so greatful..
Thanks
thetaz01 said:
I was wondering if you be gracious enough to share the Internet sharing CAB i only need to get it to work thought the USB cable and on a windows box, and from what im getting you got that far... JUST not working on a mac...
if thats the case, i would be ever so greatful..
Thanks
Click to expand...
Click to collapse
You can use the link from the previous post here, and just copy the dll's and exe to the Windows directory, and place teh shortcut into the Device\Windows\Start Menu\Programs\ directory.
Eponymous069 said:
You can use the link from the previous post here, and just copy the dll's and exe to the Windows directory, and place teh shortcut into the Device\Windows\Start Menu\Programs\ directory.
Click to expand...
Click to collapse
hey, ok great, i just downloaded the file, Just one question..
The file i downloaded has about a page of Reg Key changes, you didnt mention that in your "thngs to do"
Just want to see if i am to make all those changes or not.
thanks
So, your problem is in getting the internet connection to work and not connecting it to the mac, right? Does your mac recognize the phone as a modem?
If you're using MR1 I think you might need to hard reset and the soft reset right before the Verizon customizations run. You won't be able to run their apps but there won't be software to cripple the phone.
i have the same exact issue i have a new macbook pro and the bluetooth connects however the speed is slower then dial up it works perfectly however on bootcamp apple has to change the drivers
So more results.
I tried all the registry edits, (much easier with CD-Regedit so you can make the changes on your desktop) and now internet sharing does not even allow me to select a connection type, it had worked previously.
The only thing that was missing before I made the registry changes was that when I pair the phone, in the services listed, "Network Access Point" is not one of the listed services. My old phone has this service listed, and this is how I used it, where I started internet sharing on the phone, then selected the bluetooth device (phone) on the mac and selected: "Connect to Network) and it worked flawless.
Back to the drawing board. I'm going to try next to re-flash the MR1 rom and do as Cycomachead suggested and stop verizons customizations from happening.
bryanw17, what were the exact settings you used for dialup on the mac. The modem script used is probably the most important piece.
Number: #777
Username: Phonenumber (or [email protected]????)
Password: (We know this one, not sure if it's legal to post though)
Darn, I wish I could provide more help. It is indeed possible in Leopard, I had it going before I began flashing my phone - and I no longer have a data plan to test, otherwise I'd be using it a lot more!
aparently no one with a new macbook pro can get bluetooth pan to work. I have it connected however the drivers for the new macbook pro do not provide a good connection if you search the mac forums theyve been talking about it on there. I dont use a username n password however because i use the internet sharing app for the moment i am using wmwifirouter to connect online however my xv6800 doesnt charge at the same time for some reason so u can only use it till the battery dies
So some more results.
I installed ICS and all the registry edits. Then the internet Connection Sharing did not function at all. I verified the registry settings, all were fine. So no dice with me.
So back to the drawing board.
I installed a previous rom. DCD 3.2.6, and guess what? From initial flash of the phone and initial setup, no apps installed, no hacking, ICS runs and provides a network connection to my mac perfect. I also instantly notice when I pair it through bluetooth, it allows the option of "Access this device as a network port". And "Network Access point" is listed as an offered service.
I installed newer rom DCD 3.3.4, and the MR1 Rom. Neither have ICS installed initially. I can install the two files: intshare.dll and IntShrUI.exe into the windows directory without any reg edits, and then ICS works on the phone, but then pairing the phone to the Mac, and attempting to discover teh PAN service is unsuccessful. It only is discovered as a Dialup Access device, and not a "Network Access Point".
So, It appears I can get internet Sharing via Bluetooth PAN to function on the phone no matter which rom, but have not figure out how to tell the mac, or trick the mac, into thinking the "Network Access Point" service is available.
I have pulled completed registry dumps with CE-Regedit and compared the differences between the two, which there are quite a few, but not sure how to export these differences with the program so I can apply them to the other roms registry. I guess I might try a fukll backup and then restore to the new(er) rom and cross my fingers.
I'd stay with the 3.2.6 rom. and 3.42.50 Radio, with PRI 2.03, but I can only seem to make the GPS function successfully with the MR1 stock verizon rom.
Anybody want to take the two regs files compare, and see if they can find out where we can make the change to have the phone advertise the service "Network Access Point" when being paired to the mac or PC?
On one last note. I also tried the method of restoring the MR1 official rom, and then not allowing the customizations. ICS will function, but again, not advertising the service: "Network Access Point" when pairing, so it's not recognized as a valid networking method.
Where did you get those files (intshare.dll and IntShrUI.exe) to allow ICS via bluetooth?
Nevermind, I found it on PPCGeeks.
Don't know why DCD disabled the BT DUN on ICS.
I use Missing sync, and I turned on PAN then added my phone and it shoed it as a modem when I added it, but my BT connection is fairly Unrealible compared to the USB teather on Bootcamp
i was under the impression that bt pan has been whacked on macbook pro models starting from early 2008 on. anything earlier than that and it seems to work great. does anyone know why bt pan doesnt work on the newer machines and how to get it to work?
Related
OK. Like a lot of people, I was horrified to discover that my Mac could no longer use my Hermes' bluetooth connection (DUN) after I upgraded to AKU 3.3. Microsoft lovingly removed DUN and added PAN, which MacOS doesn't support yet (rumors are that 10.4.9 or 10.5.0 will).
So I suddenly was left without a way to connect to the 'net using my phone and my MacBook Pro.
Plugging it up USB didn't do anything -- the Mac had no idea what the phone was, and didn't know how to use it for anything.
Enter MarkSpace MissingSync. I installed the latest version (3.0.1) on my Mac, and plugged in my phone to sync it up. By chance, I ran an 'ifconfig -a' in a terminal window, and noticed this:
Code:
en2: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
ether 80:00:60:0f:e8:00
media: 10baseT/UTP <full-duplex> status: active
supported media: 10baseT/UTP <full-duplex>
So MissingSync is establishing a connection using a faked IP address. OK. Interesting. So I unplug the phone, and go into the all new "Internet Sharing" app on my phone, set it to USB and turned it to connect. I plug my phone back in, and MissingSync tries to start up (and fails). But the IP (en2) is still there. I turn off my Airport (wireless) connection, make sure Bluetooth is disabled (to make sure).. and do a netstat -rn, and lo and behold, my Mac has suddenly taken on my phone as a default gateway.
Code:
Destination Gateway Flags Refs Use Netif Expire
default 192.168.0.1 UGSc 9 40 en2
127 127.0.0.1 UCS 0 0 lo0
And... I'm on the 'net. I didn't have to create any connections, I didn't have to add any routes manually. Nothing. It just worked. (Yeah, I'm amazed, too).
Everything works. DNS, SlingPlayer, Entourage w/ Exchange.
I'm getting around 900/kbps down, 600/kbps up on Cingular/AT&T. Of course I live about 2 miles from Cingular HQ, so that's probably to be expected..
In MissingSync, turn *off* USB syncing, and it won't throw as many errors -- just sync via Bluetooth, but the drivers are still there, so it still comes up with an IP address and pseudo-ethernet device.
MarkSpace needs to market this. Awesome. It's not as convenient as bluetooth, but it's a lot faster, and you have the added benefit of charging your phone at the same time.
oh.. and one more thing... you can still use your phone for voice phone calls (when you're on 3G), and data. It works just like your're not plugged into it. And you can use a bluetooth headset with your phone while you're connected.
edited: make sure "use advanced usb networking" is turned OFF in the Settings>Connections page on your phone.
Wow, just tried this myself on cingular as well, 150k/sec down and 90k/sec up using EDGE. Extremely easy as well, just kinda works by itself if you have MissingSync installed. Posting using my TYTN right now actually.
I'm on the medianet unlimited plan so I connect through wap.cingular. Will I get hit for any additional data charges for tethering?
birdman666 said:
Wow, just tried this myself on cingular as well, 150k/sec down and 90k/sec up using EDGE. Extremely easy as well, just kinda works by itself if you have MissingSync installed. Posting using my TYTN right now actually.
I'm on the medianet unlimited plan so I connect through wap.cingular. Will I get hit for any additional data charges for tethering?
Click to expand...
Click to collapse
Very doubtful, although I don't know for sure. My phone is set to use MediaNET, and uses wap.cingular. I have PDA Unlimited Connect. From all appearances on Cingular's billing page, a notebook hooking into your phone via this method just looks like ordinary phone data to Cingular.
Now... I wouldn't use this as a primary internet connection. I'd bet if you put several gigs through the phone, they're going to get suspicious.
I actually use around 4-5 gigs a month normally (just with ActiveSync polling for mail and normal use), and they've never said anything to me.. so.. who knows.
Unfortunately, it's so difficult to get info from Cingular/AT&T these days (I'm still trying to get my [email protected] to work)..
My billing cycle is up in 7 days -- I will post back here if I see any different charges on my bill.
If this works, I'm going to hump your leg.
wow, works. time to start humping. i love you. please, bear my children.
btw, definitely worth adding to the wiki.
I am assuming that disabling the connection in Internet Sharing restores Missing Sync's normal (supported sync) functionality? Great pick-up. I already have Missing Sync and my 8525 will be here on Wednesday. Thanks.
Damn, I can't afford Missing Sync
Oh well, I bought it anyway. I'd already played with version 2.5 so I knew it was starting to get good. I can make use of some of the other features, (like importing my cameraphone snaps into iPhoto) but this internet sharing feature is why I bought it. And it works just as you said:
1) Run "Internet Sharing" on the phone with 'PC Connection' set to USB.
2) Plug into the Mac.
In fact "Missing Sync for Windows Mobile" shows up as a network interface in System Preferences / Network, too.
This is actually a lot nicer that the old way I used to do it. Before AKU 3.3 and Missing Sync 3 I was getting Internet access on my iBook over Bluetooth using Internet Connect and a lot of faffing around with modem scripts. I eventually found one that worked.. .but I always had to 'dial' 3 times before it connected and it took about 2 minutes to get a connection.
Now I can just plug in and go ... and my phone doesn't need a separate power supply to keep me connected all day. ** very happy **
(Yes, they should really advertise this!)
i'd really like my hermes to work on my Linux box, since I use it as my main system over XP.. i read a few articles regarding this, and it turns out the older version of synce worked on most HTC devices.. but for some odd reason the new ones dont seem to.. someone did mention that WM5 devices weren't supported for now.. the older WM2003 does tho..
if it makes any difference, I'm on Ubuntu Linux 6.10 32bit version..
any help is appreciated..
mizuchi said:
i'd really like my hermes to work on my Linux box, since I use it as my main system over XP.. i read a few articles regarding this, and it turns out the older version of synce worked on most HTC devices.. but for some odd reason the new ones dont seem to.. someone did mention that WM5 devices weren't supported for now.. the older WM2003 does tho..
if it makes any difference, I'm on Ubuntu Linux 6.10 32bit version..
any help is appreciated..
Click to expand...
Click to collapse
I followed the (lenghty) instructions on the synce site, and it works for me with my TyTN. I have not set up contact syncing, but I can browse/copy/run stuff from my Ubuntu 6.10 installations on my TyTN.
i'll give it another shot.. thanks for the confirmation..
jmat said:
...So I unplug the phone, and go into the all new "Internet Sharing" app on my phone, set it to USB and turned it to connect. I plug my phone back in, and MissingSync tries to start up (and fails). But the IP (en2) is still there. ...
Click to expand...
Click to collapse
I don't have en2 when connecting in Share mode
MDA Compact III
What version of Missing Sync are you using? It's working for me using version 3.01
It's 3.0.0 (315) and it reports as the latest.
Well that's clearly not true I suggest you download the new version from the site (I only got this a few days ago).
Upgraded to the 3.0.1 (downloaded from the site). The client on the phone upgraded as well. Still nothing. On the sync mode there is en2 connection (with orange status) in the network preferences. When I activate the sharing mode it disappears. Checked in terminal as well.
And you're *definitely* using AKU 3.3 on the phone?
Izzard-UK said:
And you're *definitely* using AKU 3.3 on the phone?
Click to expand...
Click to collapse
I'm sure it's 3.x but may not be 3.3. How do I check this?
So, can it use bluetooth to link up my Hermes (AKU 3.3) and connect to the internet from my macbook thru the Hermes??
bowen.chau said:
So, can it use bluetooth to link up my Hermes (AKU 3.3) and connect to the internet from my macbook thru the Hermes??
Click to expand...
Click to collapse
I don't believe so, I've only tried using the "USB" setting. Besides, the phone gets power through the USB cable and more bandwidth. There is no advantage to using Bluetooth except not needing a cable!
I have a TomTom Go 910 and an M3100 running WM6.
I have been using the hands-free BT connection with no problem.
However, I recently tried to set up a data connection to access TomTom Plus services through the phone over BT, and the setup routine fails every time. (I have no problem connecting to the internet over WAP from the phone in general).
Of course, TomTom support refuse to help, telling me that the phone is not supported for the 910. According to them I should not even be able to use the hands-free feature...
Before I go spending hours trying different ROMs and BT stacks etc., does anyone out there have the same setup (even with a 710 or 510) and got it to work? (No point wasting time if they are simply not compatible and no one has actually got it to work).
Thanks for your help
My very basic guess is that you need to use the Internet Connection Sharing program on windows mobile, as just paring the devices won't do anything.
So I guess I fire ICS up and and choose Bluetooth PAN and then try to see if TomTom sees it.?
I'll try tonight and report back.
Thanks for the suggestion.
Let us know how it goes. But isn't WM6 lacking either PAN or DUN that's required to establish the connection?
No luck using ICS
Percz said:
My very basic guess is that you need to use the Internet Connection Sharing program on windows mobile, as just paring the devices won't do anything.
Click to expand...
Click to collapse
Well, I tried it... no luck. TomTom still insists on going through a DUN setup routine (entering access point, GPRS dial-up number, etc.) and promptly fails both with automatic and manual setup. It does not detect the PAN already running with ICS connected.
I wonder if DUN can be ported back to WM6 with CABs from WM5?
Any other ideas?
I thought I saw a .cab file here somewhere that would allow you to bridge the 3G/EDGE connection to the WiFi connection so I can share my 3G over WiFi to laptop or whatever.
Anyone seen this? I cant remember the name, thought it was something like WMBridge or something.
Thanks
G
GuardianZX9 said:
I thought I saw a .cab file here somewhere that would allow you to bridge the 3G/EDGE connection to the WiFi connection so I can share my 3G over WiFi to laptop or whatever.
Anyone seen this? I cant remember the name, thought it was something like WMBridge or something.
Thanks
G
Click to expand...
Click to collapse
internet connection sharing will allow you to share your 3G over bluetooth or USB to your laptop !!
and now that I think about it you can almost certainly go through the arduous and difficult task of getting activesync to connect over an adhoc wifi connection, once that is done you will be able to use the phone as a 3G modem for your laptop.
ice_coffee said:
and now that I think about it you can almost certainly go through the arduous and difficult task of getting activesync to connect over an adhoc wifi connection, once that is done you will be able to use the phone as a 3G modem for your laptop.
Click to expand...
Click to collapse
u can do it tht way but its hard, and requires a registry hack, which to be fair doesnt work all that well, disconns after a couple of mins at best, bluetooth is the way to go if u want wireless connecton, although i use the lead for security, u can use the 3g conn as a modem, but then if u like us use tmob wb and walk then u cnt use ur data package.
hope this helps
Peter
The app is called wmWifiRouter. Looks like they just came out with a new version the 10th. Forget bluetooth, its not secured at all, and only lets you share with one device. With wmwifirouter you can share with many. See the link below.
http://forum.xda-developers.com/showthread.php?t=341398
excellent that is exactly what I was looking for, I will play with it today and see if I can get it to work.
Thanks
G
Should be a simple matter of copying the exe to your device and running it. It takes care of all the registry settings, starting up Internet Sharing, keeping the connection alive, and with the latest version you can even put the unit to sleep and your connection will stay alive. About the only thing it doesn't do is set up a peer-to-peer profile with a fixed IP address, but the thread above walks you through that. Make sure you set the profile to use WPA encryption (NOT WEP or 'open') and set a password.
techntrek said:
The app is called wmWifiRouter. Looks like they just came out with a new version the 10th. Forget bluetooth, its not secured at all, and only lets you share with one device. With wmwifirouter you can share with many. See the link below.
http://forum.xda-developers.com/showthread.php?t=341398
Click to expand...
Click to collapse
I finally got around to trying this and have had no luck. I followed the directions as best as I could tell. Anyone verify if this works on the Athena? I used to have the method set up manually but hadn't set it up again since updating to AP3.0. This would be much handier... if works!
wgary said:
I finally got around to trying this and have had no luck. I followed the directions as best as I could tell. Anyone verify if this works on the Athena? I used to have the method set up manually but hadn't set it up again since updating to AP3.0. This would be much handier... if works!
Click to expand...
Click to collapse
Powell,
Why not build this into AP 4.0 ROM?
eaglesteve said:
Powell,
Why not build this into AP 4.0 ROM?
Click to expand...
Click to collapse
i was trying for 3.0 actually but couldnt get it to work at time bc of confusing instructions. i will though in 4.0 100%
I verify that it works with the Athena and it works great. Let me know if your having trouble. I've been using it everyday now with no problems.
Pawel062 said:
i was trying for 3.0 actually but couldnt get it to work at time bc of confusing instructions. i will though in 4.0 100%
Click to expand...
Click to collapse
The directions are confusing because the newer method was grafted onto the same thread as the older method. So it's hard to tell what's what. I put about an hour into this but made no progress. The exe file doesn't appear to do anything on the Athena...
MWillis561 said:
I verify that it works with the Athena and it works great. Let me know if your having trouble. I've been using it everyday now with no problems.
Click to expand...
Click to collapse
Sorry, just saw your response as I wrote mine. Here is what I did:
1. set up an ad hoc network on my Athena. IP address 192.168.0.1 (another place saide 192.168.0.7--tried both)
2. Set up on my client (MacBook Pro). A connection was established.
3. Ran the exe file -- nothing happened. One comment said to deactivate the network before running. I did this in various degrees with no success.
4. Also opened up the Internet Sharing applet and tried to connect manually -- "USB cable is not connected."
Clearly I'm missing something here. It would be very handy to have this capability. Can you clarify??
Not sure why you are having a problem - I unzipped the zip, transfered the exe to the athena and it ran on the first try after first setting up the ad-hoc wifi connection (settings, connections, wi-fi, network adapters tab, IEEE..., use specific IP address in the 192.168.x.x range; then go to the other tab and set up an ad-hoc connection).
I had an even worse experience. Everytime I ran the exe, my Athena locked up, needing a complete reset each time.
I gave up in the end .
I have got other methods to work using Mortscipts, but it does seem like something that would be well worth someones time sorting out for the good of us all.
Have you tried the latest version of wmWifiRouter? The developer released a new version of it earlier this month. Its on version 0.8 now.
Is it possible to use ICS with wifi connection instead of cellular connection? Would be useful for a makeshift wireless adapter if your regular NIC or wireless NIC fails.
It seems that even if I have a wifi connection already going and then I launch ICS and connect, it still tries to dial out and use the cellular connection. You would think if it can share cellular data it could share wifi data just as easily but maybe im missing something.
Back in the early days of WiFi internet sharing the private interface was changed to WiFi with a manual registry edit. It might be possible to change the public interface to USB instead of defaulting too the cellular radio. It would probably take a fair amount of troubleshooting, but I'd think it would be possible. I think the entries were at HKLM\Comm\ConnectionSharing. Might be a starting point...
Search for WMWifiRouter
WiFiRouter
WiFiRouter works by making your ppc into a virtual access point. Then you can share the internet through it.
Last time I looked however, the author had withdrawn the program from circulation at version 0.91. There must be some problems with it because the author indicated that he would release a new version once he ironed out some bugs. If it is not back in distribution yet, you might be still able to find it on a torrent site. If not, PM me and I will send you the cab. Some of the cab collections at ppcgeeks ftp have it inside too. One good collection to check is Alex's.
I have used it and it works.
-------------------------------------------------------------------
VZW XV6800 Stock 1.30 radio dcd 1.7.0 customized rom. freedom mini keychain gps
Edit/Delete Message
wmwifirouter is not what he's looking for. That is still using your phones internet. He wants to see how he could use the phone as a Network card, using the wifi connection, as oppossed to the sprintpcs connection.
I too would be very interested in this happening, if anyone knows of a way please tell.
ok, but why ??
Why would you actually want to do this anyway ??? I will look into it but it makes no sense when a USB WiFi dongle is $30 or so and does not run your phone down to use it, why would you want to use your phone as a very expensive USB WiFi card ??? Maybe I am missing some golden benefit ????
I dont get it either, but he did say in an emergency if your wifi went out.
Thank you for the responses.
Yes, it would be useful if your wireless nic went out (or regular nic for that matter) just to have something to use for the moment. Or maybe you brought your computer to a friends house and hes out of ports or you dont want to run 50ft cable to his kitchen table
But the titan has wireless, it has internet sharing, why doesnt the wireless show up in the list of available networks? I'm not saying its an all important feature but it would be yet another cool thing your phone could do.
i looking to use my mogul as a wifi access point (sharing Spint Vision thru wifi)
i tryed the procedure to mod the registry to enable it but i cant get it to work.
anyone know the exact procedure for the mogul
btw i also checked out WMWifiRouter...looks like it's no longer free
I also wanna know
Look the idea is simple. So where is the phone ICS telling it to use the celluar line and not allowing the option of the wifi?
Pls any one contact me. Its a cool feature for a phone
Fr3nZy said:
i looking to use my mogul as a wifi access point (sharing Spint Vision thru wifi)
i tryed the procedure to mod the registry to enable it but i cant get it to work.
anyone know the exact procedure for the mogul
btw i also checked out WMWifiRouter...looks like it's no longer free
Click to expand...
Click to collapse
I bought software called Walking Hotspot, which essentially turns my Mogul/Titan into something like a Mifi, sharing my cellular data with my laptop. Otherwise known as tethering.
I only use it for emergencies because I am not sure if Sprint can tell that I am tethering. I believe if Sprint detects unauthorized tethering they will charge 4 cents per kilobyte of data .. which is very harsh!
-----------------------
Jav Atar
I feel like I need to 1st explain that although I don't post here often I'm not an absolute noob. I load a new ROM about every 30 days and used Tierman before advancing to Sashimi. Ever since the 6.5 roms dropped I've been unable to see my Titan from ANY laptop/desktop. I'm looking for others with the same issue and/or if this is a known issue that has been resolved.
Tried RyanMogul6800 2.2 Heavy
Tried JUSTPCTECH 6.5 Rom
Tried an un-named 6.5 Rom prior to the 21501 release
Same issue on all of these roms, SSID/PPC not visible
Device is a 6800 Alltel branded on the Alltel network
WMWifirouter version is 1.35
Tried deleting the wifi listing on the pc's/laptops
Tried re-installing WmWifirouter
Tried rebooting everything
Tried changing hardware switch to control ringer on/off instead of wifi
Tried manually powering on wifi via Comm Manager
I know wmwifirouter started out testing here so I hope they see this post but I will be accessing my paid support with wmwifirouter to submit a support ticket.
Has anyone else experienced this?
What did you do to fix it?
Try going into settings, connections, Wireless LAN, change power mode to best performance. Then go into settings, connections, wifi and if any connections are in there delete them. Make sure no connections are attempting to connect. Now turn on wifi switch and go back into wifi settings. Pick to see ad hoc only and create new. Make a name and make it an ad hoc connection, pick open connection no security protection. Finish. Now using wifi on a laptop/desktop refresh the wifi and you should now see your connection. Quick tip when using WmWifirouter. Make sure nothing is connected to your PPC's adhoc connection. Have the wifi switch enabled BEFORE turning on WMwifirouter, Once its connected you can then use a desktop or laptop and connect to the PPC, and dont turn the WIFI OFF until you have quit WMwifirouter. I use the network plugin to access shared folders on my PC to transfer music etc.. Also make sure the wifi on the PC is not set up to share its own connection. That will interfere with the networking with the wifi on the PPC. Let me know if you get wi-fi working.
Thanks and I'm trying that now..only thing is I've been using WMWifirouter cince before it was 1.0 and it always worked fine. While i'm trying your suggestion is their anything different with 6.5 that would have me manually connecting.
I'm used to setting up wmwifirouter in the office and letting 2 otherppl access it and just GO! This happens on Vista, XP, and Windows 7 (I'm an MSDN subscriber). Anyhow trying your suggestions and let me know about 6.5 if you goet a sec.
Thanks
Tried it and my network showed up for a sec but when I tried connecting it timed out and then never showed up again. USB to 3G works fine and I tried ur suggestion on Vista & XP. Still pokin away. Hope sumthin works out!
Just a side note. My wifi IP on the 6800 is always all 0's 0.0.0.0 Shouldn't it be 192.16.3.1 and DHCP is enabled BTW
I'm experiencing a similar problem and have tried several 6.5 builds, including my own from the ppckitchen. WIFI will work for some time and then stop. It will work again for a short time after rebooting but then will stop once more.
So after JustPCTechs (I prefer Ryans Rom) rom i am back on RyanMogul's heavy & it's still not working. I like many people looked at others with this issue like it's something they are doing wrong but I am an EVERY DAY user of wmwifirouter. I cancelled my itnernet at the house simply because Alltel's unlimited was so fast. I even had the kid's Xbox 360 running through it.
So I'm still stuck with no wifi for wmwifirouter. Even after Ryan's suggestions. I know other people have this problem. I just wish you guys would speak up so we can collect data on this issue and resolve it for real.
No disrespect to the very talented individuals whom have assisted me so far. You and your work are greatly appreciated.
I'm also verifying the problem exists. Also I cannot connect my home pc's internet through the USB cable to the phone anymore. I have verified this same problem with all 3 of the 6.5 roms I've tested. I tried ryan's suggestion but to no avail. Looks great though!!
For the issue of the PPC not being able to use your PC's internet through USB cable you may want to try going into settings/connections/connection settings/select network. Make the top drop down menu My work network and the bottom drop down menu make your Carrier ex:Cricket, MetroPCS, etc.. That way should use your WAP when unplugged and use the PC's home connection when plugged in. That would then be normal operation.
SOLVED:
So I was poking around in the 6800 and I never use wifi because Alltel is SOOO fast. I saw a saved network connection ON THE 6800 to wmwifirouter. I thought it was odd since I asked wmwifirouter to dynamically create the network each time instead of storing it.
After doing that I was able to consistently see the 6800 from any device.
So Comm Manager / wireless Lan/ delete wmwifirouter
I've had the usb issue a long time ago and it is not the same.
RyanMogul6800 said:
Then go into settings, connections, wifi and if any connections are in there delete them. Make sure no connections are attempting to connect.
Click to expand...
Click to collapse
If you notice i already said to delete existing wi-fi connections. So my first responses were your solution. you just overlooked it.. take care glad your sorted out.
I guess I did and let me make this real clear for anyone reading this later on. Wmwifirouter creates a wifi connection ON YOUR PPC DEVICE - TO YOUR PC DEVICE.
So when people tell you to delete all wifi connections and you delete the one on your laptop/desktop don't forget (like i did) to delete it on the ppc as well. I never knew thats how wmwifirouter worked. Learn somethin new every day. Thanks to all that helped.
ebonygirl said:
I guess I did and let me make this real clear for anyone reading this later on. Wmwifirouter creates a wifi connection ON YOUR PPC DEVICE - TO YOUR PC DEVICE.
So when people tell you to delete all wifi connections and you delete the one on your laptop/desktop don't forget (like i did) to delete it on the ppc as well. I never knew thats how wmwifirouter worked. Learn somethin new every day. Thanks to all that helped.
Click to expand...
Click to collapse
In my instructions it is telling you to delete the connections off of the PPC.. Any connection on your PC would not automatically connect unless u had a matching ad hoc connection on ur PPC. I provided the fix and u overlooked/misunderstood it. I am glad you got ur wifi back up and running.