Related
Just saw this on ebay...Im a fan of housing and facia. But i know %98 of TP2 owner right now dont wanna touch the Hardware section of the phone.( for customizing)
It Just nice too see that we can tweak not only whats inside but also the outside too... Im just hoping for a nice fit and high quality. Its too early to tell how good this housing is but i wanna know soon.
http://cgi.ebay.co.uk/ORIGINAL-HTC-...s_JN?hash=item4cea1e075a&_trksid=p3286.c0.m14
I also noticed that a couple days ago but they only offer red and blue right now. I'm not savy enough but I think it's a cool options
For that, did you know how to dismount the TP2 ?
Looks like not really easy to operate at first glance...
You get a screwdriver with it ... just find all the screws and replace!
wait few months... dismantling this phone will be on youtube!
I noticed those when I bought my TP2 last week... to bad they are only red and blue. I would be down for black, or maybe a nice dark green. They look nice from the photo. I don't like taking apart slider phones... PITA
The Wing wasn't so bad. I did the whole thing solo since my brother broke his screen and there weren't any dismantling guides available yet. It's easier than you think... just don't force anything and keep a sharp eye open for screws.
The only problem with swapping the case for a T-Mobile version is that you have to keep the T-Mobile keyboard. The layout is unique to T-Mobile and the HTC version (as well as other carriers) vary from model to model.
freakingwilly said:
The Wing wasn't so bad. I did the whole thing solo since my brother broke his screen and there weren't any dismantling guides available yet. It's easier than you think... just don't force anything and keep a sharp eye open for screws.
The only problem with swapping the case for a T-Mobile version is that you have to keep the T-Mobile keyboard. The layout is unique to T-Mobile and the HTC version (as well as other carriers) vary from model to model.
Click to expand...
Click to collapse
It's really easy to swap cases. I had to replace the screen on my room mates Kaiser which is a slider tilt screen device as well. Took me 40 mins tops & I had to completely disassemble it. Will probably have to again soon. He broke his screen a second time lmao. The one thing I'll note though is for T-Mobile, the whole device is different basicly. The screen does have a tappered edge & the screen cover is bigger & the battery cover is a completely different design. the Stylus doesn't go through it. So, the T-Mobile wouldn't be completely changible. As for the keyboard, that can be changed via ROM. The HTC Kaiser has a different KB Layout than the AT&T Tilt, we just install a CAB to "fix" this as the ROM's are made for the HTC version. Also, the Sprint/Verizon/AT&T(From what I read) have Headphone Jacks. You could arguably use only part of the kit, but for $80-100+, I want one completely compatible with my device.
As for Colors, there's a full silver/full black/& black & orange version available. I wish they made them available in pieces so you could mix & match parts. For example the Battery covers.
Anyone knows whether a housing is available for the european version? Mine has some ugly scratches due to close contact with the asphalt Can't find a new housing though, only bezels... I need a new grey edge around the keyboard to which the battery cover is attached aswel. Is this even possible?
Luckily, the keyboard, screen and batt cover are still intact, and the phone is still functioning properly. It is now protected by a plastic rubberized case and a screenprotector.
Help would be very welcome!
I'm thinking about giving this a try to replace the screwed up button layout that ATT provided. If I can just swap the buttons and the remap the keys with a cab file I'm thinking I can get the QWERTY keyboard back to it's original form.
Anyone else tried this?
Jon
Tried going to the link but it appears to have been "removed".....anywhere else?
This one is working for me.
http://cgi.ebay.com/HTC-TOUCH-PRO-2-T7373-OEM-RED-FULL-HOUSING-KEYBOARD-US_W0QQitemZ350292809157QQcmdZViewItemQQptZPDA_Accessories?hash=item518f1415c5
Lets focus on getting everyone behind this one thread - maybe we can get someone to confirm! Thanks! http://forum.xda-developers.com/showthread.php?t=547632&page=4
Schmurtz1968 said:
For that, did you know how to dismount the TP2 ?
Looks like not really easy to operate at first glance...
Click to expand...
Click to collapse
Dismantling HTC Touch PRO2, HTC Rhodium in pictures...
The above dismantling link has been in the XDA-Wiki for several months now.
So what? If someone asks a question and I can help, I sure will. Or should I be an smartass and tell it's around here, use the search... Maybe it's your thing, not mine.
i'd like to try to replace the bezel on the screen-part, it's got little wholes and even a completely crushed section.. but according to the link you'll have to disassemble the whole keyboard-part in order to do that.. isnt there an easier way to replace the bezel??
just wanted to let everyone know that I have the black/blue case from ebay china. It took 3 weeks but I finally have it.
After taking apart my g1 and 90% housing conversion from white to black. I accidentally cut one of the ribbons off and broke the phone. So im a little scared to take apart this $400 phone. Didnt mind the g1 because there dirt cheap and easy to find another one.
If you all can gather some links and any guides I will probably convert my tmo tp2 to the new housing sunday mourning. unless someone can confirm that its extremly easy to switch housing.
Just an example of the g1 dissemble.
http://www.youtube.com/watch?v=3PdhXx3g9nU
ive been modding hardware since everyone had a nextel i730. ive seen alot of crappy poorly made housings in my days. usually the first and second generation batches of housings that come out are poorly cut, or made of brittle plastics. i would advise that when looking for housings(especially for expensive devices), that you get a 3rd generation housing and look on youtube for directions.
So excited.
I am trying to covert my T-mobile touch pro 2 soon. The full housing will arrive in 2 days. I dropped my precious on the pavement.... T-mobile housing is nowhere to be found so I bit the nail. Hopefull it's going to turn out awesome
Check this one for taking apart. flickr.com/photos/[email protected]/sets/72157621828152091/
Ok, maybe I'm not a genius, but I would have thought the search function would have helped here, but alas either Im too simple or its too complicated.
I have seen DOZENS of screen protectors, ranging from $15 to $50.
What I have noticed is that MOST folks have said that the water applied ones are to be avoided (ok, applying water to your screen I can see that), then the one for $15 got such HORRIBLE reviews, starting with 4+week deivery times, Im thinking THATS not good either,.
So, for those of you who have invested in them, maybe a stickey that will help direct the rest of us to where you got youres what you paid and why you like Or dislike it.
would be GREATLY appreciated.
thanks
Yes, I agree
+1
The Skinomi one is a wet application protector but if you follow the directions you will be fine and definitely happy with it. Read up on the thread for it at the Accessories section.
You don't spray the screen; you wet the protector before application. Read up so you'll know how not to screw it up and be patient after you've applied it to allow for proper drying before you turn the gTab back on.
I'm very happy with it.
SJM,
thanks for your reply, youre the 1st one I;ve seen who HAS been happy with the wet ones.
and I guess this WOULD have been better in accessories huh?
My search probably would have turned up more eh?
well I said I wasnt a genius.....
Thanks
The skinomi one sucks IMHO. It's rubbery and hard to get the blobs out, also if you push too hard you can dent it. And it is hard to play games on, there is too much "grip" when sliding your finger around.
I am still trying to find a decent hard screen protector that matches the one I use from SGP for my IPhone. Unfortunately they aren't making one, have no plans to make one, and don't even make one big enough to cut down to size.
Hi all,
Ok, so i've had a small disaster. As you probably guessed already i've dropped my phone. I thought the story was quite amusing (or just plain unfortunate!) so i'll you tell that before I ask for some advice!!
I got myself a white Galaxy S2 on upgrade through Vodafone. Gorgeous piece of kit so I ordered myself a nice case and screen protector to keep it nice and tidy.
Unfortunately the case got 'lost in the post' and as such the phone was unprotected. So, with some foresight I ordered a plain white cheap one off eBay (£2 inc. postage) just to see me through the 3-5 days I needed before the case I wanted was resent.
However what was sent what not white at all - it was the most hideous case with a rather disgusting floral effect all over it. I was going out for a night in town and had no choice, I had to take it with me.
Unfortunately later that eve I was stood at the bar, and my phone went off. So to save any embarrassment I slid the phone out of it's hideous case, and proceeded to read the message. Then it happened. The slippery son of a ***** jumped out of my hand, bounced off my foot and hit the deck.
It only has a couple of dings in the chrome bezel (the chrome effect rubbed off in two places to reveal black (the plating is obviously really thin)) - everything else was ok. Phew. But i'm still gutted and annoyed with myself
So, lesson learnt. I should have left the disgusting garish floral case on and it would have saved my phone. It was only 'de-sheathed' for a second and I managed to drop it, classic.
As a temporary solution, I coloured in the affected areas of the bezel with a silver permanent marker, and used some clear nail varnish over the top to stop the pen coming off. It seems to work well actually, and it looks much better than the black marks.
So, to my question - how do I change the chrome bezel for a new one?
I have read many threads, and watched many videos, and it looks to me like a nightmare job (eg as well as taking off the back and all components, you have to prise off the screen which is glued on, disconnect digitiser, etc). Can anyone confirm this, or has anyone tried it?
I can't find any videos of changing the bezel - they all seem to only go as far as taking off the back.
I've found a couple of sellers which sell the housing in white for only £20-30, so if it's an easy-ish job i'd have a stab at it. However i'm thinking I might as well just forget it ever happened and not be so precious about keeping the phone in A1 condition - it's a phone after all and it's going to encounter some scrapes now and then, even with a case on. And I plan on keeping it for 18 months anyway.
Opinions, anyone?
Cheers!
Movisman said:
Hi all,
Ok, so i've had a small disaster. As you probably guessed already i've dropped my phone. I thought the story was quite amusing (or just plain unfortunate!) so i'll you tell that before I ask for some advice!!
I got myself a white Galaxy S2 on upgrade through Vodafone. Gorgeous piece of kit so I ordered myself a nice case and screen protector to keep it nice and tidy.
Unfortunately the case got 'lost in the post' and as such the phone was unprotected. So, with some foresight I ordered a plain white cheap one off eBay (£2 inc. postage) just to see me through the 3-5 days I needed before the case I wanted was resent.
However what was sent what not white at all - it was the most hideous case with a rather disgusting floral effect all over it. I was going out for a night in town and had no choice, I had to take it with me.
Unfortunately later that eve I was stood at the bar, and my phone went off. So to save any embarrassment I slid the phone out of it's hideous case, and proceeded to read the message. Then it happened. The slippery son of a ***** jumped out of my hand, bounced off my foot and hit the deck.
It only has a couple of dings in the chrome bezel (the chrome effect rubbed off in two places to reveal black (the plating is obviously really thin)) - everything else was ok. Phew. But i'm still gutted and annoyed with myself
So, lesson learnt. I should have left the disgusting garish floral case on and it would have saved my phone. It was only 'de-sheathed' for a second and I managed to drop it, classic.
As a temporary solution, I coloured in the affected areas of the bezel with a silver permanent marker, and used some clear nail varnish over the top to stop the pen coming off. It seems to work well actually, and it looks much better than the black marks.
So, to my question - how do I change the chrome bezel for a new one?
I have read many threads, and watched many videos, and it looks to me like a nightmare job (eg as well as taking off the back and all components, you have to prise off the screen which is glued on, disconnect digitiser, etc). Can anyone confirm this, or has anyone tried it?
I can't find any videos of changing the bezel - they all seem to only go as far as taking off the back.
I've found a couple of sellers which sell the housing in white for only £20-30, so if it's an easy-ish job i'd have a stab at it. However i'm thinking I might as well just forget it ever happened and not be so precious about keeping the phone in A1 condition - it's a phone after all and it's going to encounter some scrapes now and then, even with a case on. And I plan on keeping it for 18 months anyway.
Opinions, anyone?
Cheers!
Click to expand...
Click to collapse
Sorry to hear...similar happened to my HTC Desire...however this should help...if you buy the kit off Ebay...
http://forum.xda-developers.com/showthread.php?t=1253969
0semaj0 said:
Sorry to hear...similar happened to my HTC Desire...however this should help...if you buy the kit off Ebay...
http://forum.xda-developers.com/showthread.php?t=1253969
Click to expand...
Click to collapse
Hi,
Thanks for the information - I had a look at this tutorial yesterday, and although it's very good, it looks like this person has replaced the entire led panel/digitiser/housing in one go, rather than just the housing?
My screen is just fine, so I only need to replace the housing part.
The hardest bit looks like separating the screen from the housing from what i've read, and this is what I can't find a tutorial for, only some images on youtube suggesting to use a hairdryer to help with the proceedings!!
Thanks
Movisman said:
Hi,
Thanks for the information - I had a look at this tutorial yesterday, and although it's very good, it looks like this person has replaced the entire led panel/digitiser/housing in one go, rather than just the housing?
My screen is just fine, so I only need to replace the housing part.
The hardest bit looks like separating the screen from the housing from what i've read, and this is what I can't find a tutorial for, only some images on youtube suggesting to use a hairdryer to help with the proceedings!!
Thanks
Click to expand...
Click to collapse
Yea, the link is for the whole unit, but would give you some pointers. I am not as familar with the Samsung build, but with the HTC I know that between the LCD housing and the LCD/digitiser itself is applied through adhesive (most phones are) that is put into a temperature oven for 10 minutes to soften the adhesive. This is based on the HTC Official Service videos. I am not sure if the same will apply to Samsung phones.
But then again, as it is an expensive phone, it may be ideal for you to also get a quote from your local SSC or mobile phone repair agent to consider.
0semaj0 said:
Yea, the link is for the whole unit, but would give you some pointers. I am not as familar with the Samsung build, but with the HTC I know that between the LCD housing and the LCD/digitiser itself is applied through adhesive (most phones are) that is put into a temperature oven for 10 minutes to soften the adhesive. This is based on the HTC Official Service videos. I am not sure if the same will apply to Samsung phones.
But then again, as it is an expensive phone, it may be ideal for you to also get a quote from your local SSC or mobile phone repair agent to consider.
Click to expand...
Click to collapse
Yep, good point. I'd be interested to hear actually what the cost would be to replace the front bezel only. It's only £30 on eBay for the front and rear housing, but i'd be willing to pay more on top for an authorised repairer to carry out the job.
That tutorial is definitely one of the more detailed ones I have seen so far though. Doesn't look like many people have tackled changing the bezel only...
Thanks
Movisman said:
Yep, good point. I'd be interested to hear actually what the cost would be to replace the front bezel only. It's only £30 on eBay for the front and rear housing, but i'd be willing to pay more on top for an authorised repairer to carry out the job.
That tutorial is definitely one of the more detailed ones I have seen so far though. Doesn't look like many people have tackled changing the bezel only...
Thanks
Click to expand...
Click to collapse
Hey Movis,
What did you end up doing for your dropped phone?
I too have dropped my phone on its corner and the chrome along with the plastic is now dented.
Another one with the same problem here. I managed to create a bump on the chrome bezel.
Can I bump this post as I've also just noticed a ding in the corner of the chrome bezel was wondering if anyone had found a solution to this yet.? short of replacing the LCD/digitiser which like OPs phone are working fine. It's just cosmetic damage.
I once was in a bad mood and snapped a screen and backing/housing in half.I can't remember exactly,but I'm thinking the chrome bit may be part of the thin metal casing/housing that is glue taped onto the screen.
You separate the screen from the housing by using a hot air gun sparingly.
If you look back at a motherboard thread I was involved in,a person on here called Roger put up a great video tutorial link that may answer all your questions...
Sent from my GT-I9100
Ah cheers for the reply. Had a look at the mobo post you were involved in followed it to the link and coincidentally that's the exact video I watched last night. Very good video good detail and instructions. But its the black one he is stripping down so he makes no reference to the bezel which afaik is only used on the white ones.
Sent from my GT-I9100 using xda premium
I've not seen the chrome bit listed separately,so I guess its part of the metal top housing that the LCD is glued to.I've got a white one and its got a ding on it too.
You could email Samsung to see if you can get the part,but I think its not worth risking cracking the screen and you probably couldn't resuse / would get that stupid gluey tape stuff.
Sent from my GT-I9100
Appreciate it's been a while, but this seems to be the only post that matches what happened to me, so figured I'd update with my experience.
As above, dropped and dented the bezel, screen was perfectly intact, but the dent was so severe, it actually lifted a corner of my screen up. I have intentions to sell on so I wanted to fix this and pass on.
I followed this disassembly , apart from the bit about not worrying about damaging the screen as you prise it away. The housing I ordered off ebay came with a little kit, so I warmed the screen with hairdryer for a couple of minutes, then slowly prised it away, from top to bottom, inserting the tool right down the middle as the video mentions there is a large adhesive right down the middle.
Following the vid all the way to the removal of all components, this is where I ditched my current bezel/housing and reassembled into the newly ordered one. Judging by the assembly, there is no way that a bezel could be replaced without replacing the housing, it's one whole unit, and I very much doubt the build would be that drastically different for the white SGS2.
Some things to note:
Be very careful removing the vibrate motor, the connector and natural pivot point is the weakest part (new module ordered from ebay
If you are transplanting the screen like me, have some adhesive pads in your kit as most tutorials are for new screens, and as can be seen on the vid, these come with pads intact, ready to apply
Try do it in daylight
Hope that helps anyone in a similar situation.
vyks10 said:
Appreciate it's been a while, but this seems to be the only post that matches what happened to me, so figured I'd update with my experience.
As above, dropped and dented the bezel, screen was perfectly intact, but the dent was so severe, it actually lifted a corner of my screen up. I have intentions to sell on so I wanted to fix this and pass on.
I followed this disassembly , apart from the bit about not worrying about damaging the screen as you prise it away. The housing I ordered off ebay came with a little kit, so I warmed the screen with hairdryer for a couple of minutes, then slowly prised it away, from top to bottom, inserting the tool right down the middle as the video mentions there is a large adhesive right down the middle.
Following the vid all the way to the removal of all components, this is where I ditched my current bezel/housing and reassembled into the newly ordered one. Judging by the assembly, there is no way that a bezel could be replaced without replacing the housing, it's one whole unit, and I very much doubt the build would be that drastically different for the white SGS2.
Some things to note:
Be very careful removing the vibrate motor, the connector and natural pivot point is the weakest part (new module ordered from ebay
If you are transplanting the screen like me, have some adhesive pads in your kit as most tutorials are for new screens, and as can be seen on the vid, these come with pads intact, ready to apply
Try do it in daylight
Hope that helps anyone in a similar situation.
Click to expand...
Click to collapse
Hi, will the heat actually damage the screen? I saw some posts mentioning about putting it into the oven and such. It sounded very intense but if it works without damaging the screen, i might give it a try. Facing the same situation as yours. Scratches and dents all over my front chrome bezel.
Dear there
anyone have any idea where i can find digitizer for this phone and what about its price anyone can help !!!!!
ebay?
I actually just bought one myself (have bought another one a while back as well)... They will run you anywhere from around 35 for a crappy one which is the first one i bought (i wouldnt recommend it). And 45$ for an OEM one from amazon (just hope you don't get a used one like some people say they have gotten) I do warn you that replacing it can be a hassle. I would not attempt it unless you are very careful and have a nice, clean, organized work station and a nice youtube video to watch. Make sure you keep the screws and parts grouped together by where they go.... if you drop one it will be hard to find.
http://www.amazon.com/Original-Genuine-Touchscreen-Digitizer-Motorola/dp/B0053EYGEO/ref=pd_cp_cps_0
A note... the crappy one worked, but the sensor parts werent tinted like on the OEM one... was kind of annoying. Also it should come with the tools and adhesive needed...
Yep. Kid got a hold of it before case arrived. Yes its my fault. Should have kept better eye on him. There are only two bids on YouTube. Neither one is great. I see on eBay they have LCD and digitizer and housing. From vids it looks easy. But would like to hear from anyone who has done it. Thanks
So sorry for the breakage. Here is a video that seems pretty good, https://www.youtube.com/watch?v=qm6NwBvo6T0. The process doesn't seem to hard, to me. Good luck.
kimtyson said:
So sorry for the breakage. Here is a video that seems pretty good, https://www.youtube.com/watch?v=qm6NwBvo6T0. The process doesn't seem to hard, to me. Good luck.
Click to expand...
Click to collapse
I recently replaced the LCD screen on a OnePlus One, other than the size, it was almost identical to the Mate2. couple parts in different spots but it had enough of those #%(@!)% rice grain size screws that I put them on a magnet, to make sure I didn't lose them.
Yes. That is one of the vids I was talking about. The other one was actually for a mate. Not mate 2. The thing I don't understand on this video is he never actually gets to the part of the screen replacement. So, I am presuming that with this phone as long as I purchase the LCD+digitizer+frame. Then it will just be a matter of putting all the parts including board back in to it. On eBay there are choices. You can purchase just the glass or glass and digitizer or those plus what they call the frame. While on my phone. Only the outside glass is broken. I am going to buy the kit that has all three. I would give just replacing the glass a shot if I could find a video or tutorial. I have looked everywhere. Nothing. The closest thing I could find is the vid on youtube of the guy changing just the glass on his mate. Unfortunately, he never says a word in that vid. I guess it's just to show it can be done. I'm really stressed by all this. I would prefer to just change the glass if only I could find some info. I presume it is like a Samsung where glass is glued with local to digitizer. I have fixed those type on a s3 and note 2. Was not that hard. Just be sure to heat properly and don't scratch digitizer. With no idea of how it is done on this phone. I guess I will get the kit and hope for the best as of course. It has to come from China. Waiting....Thanks for the info and I will do my best to make a vid so others can learn from my mistakes? Lol or hopefully success.
Have a hair dryer or a heat gun handy just in case. On the OnePlus, the screen is "glued" somewhat, to the plastic frame. It is a LOT easier to separate if you heat is up a
bit. Just heat one side, then you the (as I like to call it) guitar pick tool to start to pry it up, then to a little more at a time, so you don't overheat the broken screen.
After you get the screen off, make sure you scrape around the edges of the frame, to ensure you remove any sticky residue. You don't need to heat up the new screen. Once you press it down, it will stick quite well.
If it were me I would get the entire kit and be done with it. There is too much that can go wrong with the hairdryer and peeling the old, broken screen from the digitizer. With the kit, it's just all screws and dismantling then put it back together. Much easier.
I hope that is right about the kit. The thing that scares me is what will the quality of the parts be like? I know my digitizer is fine. So I'm going to try the kit first. If it fails due to bad parts. Then I will still have the option of just doing the glass. The cheapest I saw for the glass was 18.00 bucks. The kit with shipping was 58.00....Not really a huge difference. Again its the quality of the parts that scares me. Of course the vid on youtube makes it look easy. But I'm sure he is doing it on a phone that has been torn down a few times. Its always easier then. As I said. I intend to video all this. If nothing else. There will at least be more info available to poor suckers like me..lol. Will see in a couple weeks if the Chinese ship time holds true...
I'd bet the quality is the same as OEM.
Sent from my MT2L03 using XDA Free mobile app
One other thing. Just wanted to ask. You say the one plus is about the same? Are you saying that because there similar in how their made? Or do you know something about where their made. Thanks for the info on the glass. I have done it on Sammy phones. Has to be similar. Kit is already coming. So I'll go that route first try. Wish your repair had been on a ham2. Then I would feel better. I guess I get to go first. Lol
kimtyson said:
I'd bet the quality is the same as OEM.
Sent from my MT2L03 using XDA Free mobile app
Click to expand...
Click to collapse
The one I ordered for the OPO looked identical, except the routing for the lcd screen connector was just a little different, but in no way caused a problem.
I wanted to update you guys on how the repair of my screen is going. I have some info to share and trust me. It is important if you ever need to DIY on this phone. Most are aware of the video on youtube. Ive watched it several times and I always got the feeeling it looked to easy. Well, my screen and dig assy came in today. I was going through the process of tearing it down and everything was going well. Untill i got to the part where you remove the power button cable. The one that runs along the side of the phone. I SHOULD HAVE KNOWEN. In his vid. He makes it look like this cable will come off with gentle pressue. BULL****. It wont. It is glued Tight and you will just winde up tearing it. I am so pissed. I wish he would have just said to buy the cable with the kit. Its 10 bucks on ebay of course. So, now I have a torn down phone waiting for the cable. I was making a video of the repair. When the cable comes in. I will finish it and upload to youtube. The other thing he makes look easy is the removal of battery. Again, its not and you could damage it too. But I managed not to. Anyway i am really upset right now so sorry for cussing. I want to find that dude and shake his hand and smack him at same time...
pckarma112 said:
I wanted to update you guys on how the repair of my screen is going. I have some info to share and trust me. It is important if you ever need to DIY on this phone. Most are aware of the video on youtube. Ive watched it several times and I always got the feeeling it looked to easy. Well, my screen and dig assy came in today. I was going through the process of tearing it down and everything was going well. Untill i got to the part where you remove the power button cable. The one that runs along the side of the phone. I SHOULD HAVE KNOWEN. In his vid. He makes it look like this cable will come off with gentle pressue. BULL****. It wont. It is glued Tight and you will just winde up tearing it. I am so pissed. I wish he would have just said to buy the cable with the kit. Its 10 bucks on ebay of course. So, now I have a torn down phone waiting for the cable. I was making a video of the repair. When the cable comes in. I will finish it and upload to youtube. The other thing he makes look easy is the removal of battery. Again, its not and you could damage it too. But I managed not to. Anyway i am really upset right now so sorry for cussing. I want to find that dude and shake his hand and smack him at same time...
Click to expand...
Click to collapse
I have worked on several phones. None are easy really. Most all companies use some type of adhesives. Alot glue the batteries in as well. Dunno if you tried it but heat seems to help with the glue. Seen a guy do it with a hair dryer. Worked for me as well with a screen replacement. Never took one of these apart so I have no idea if they use heat activated glue or not. Good luck!
Well Thanks for reply. I too have fixed a few. As long as I have something to guide me. Im Cool. Vid or written indtructions. Yes all phones use some sort of glue. With this one on the cable. Heat would not have helped. You would just melt the cable. I was expecting some adhesive. But not like this. This was not meant to be reused. Period. Thats my point. I wish he would just have said buy the cable. No way it is coming off in one pc. The speaker is also glued down extremely tight. I think I got it. Its still in one pc. Interesting enough. There also on ebay.
I really just want people to know about the power cable. If you have to replace screen on this phone. Get one. Your gona need it. Now it may be middle of july by the time I get the cable. I went ahead and tore everything else out of phone. Tomorrow I will put all back into new assy. But i wont know if it worked till cable gets here. I forgot to record taking out the other pcs. I was just to stressed. But I do have some good vid for most of it. Gripe is now over. il be back when cable gets in...
pckarma112 said:
Well Thanks for reply. I too have fixed a few. As long as I have something to guide me. Im Cool. Vid or written indtructions. Yes all phones use some sort of glue. With this one on the cable. Heat would not have helped. You would just melt the cable. I was expecting some adhesive. But not like this. This was not meant to be reused. Period. Thats my point. I wish he would just have said buy the cable. No way it is coming off in one pc. The speaker is also glued down extremely tight. I think I got it. Its still in one pc. Interesting enough. There also on ebay.
I really just want people to know about the power cable. If you have to replace screen on this phone. Get one. Your gona need it. Now it may be middle of july by the time I get the cable. I went ahead and tore everything else out of phone. Tomorrow I will put all back into new assy. But i wont know if it worked till cable gets here. I forgot to record taking out the other pcs. I was just to stressed. But I do have some good vid for most of it. Gripe is now over. il be back when cable gets in...
Click to expand...
Click to collapse
With any luck you may save someone else a headache!
pckarma112, so sorry for your frustration. Thanks for sharing your experience.
I was going to suggest the the same thing as Moody. Heat from a hair dryer usually helps soften the glue but isn't enough to destroy anything (usually).
Just so we are all understanding, can you show a pic or provide a link of what you purchased? Was it just a screen or an assembly?
Again, sorry for your issues. Hang in there.
Parts
Yes I can. That is if I can post links. So Il try. This is the link for the power cable: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItemVersion&item=291410104104&view=all&tid=1181571120019 This I just ordered yesterday. The deleivery is anywhere from middle of July to second week of August. Im keeping my fingers crossed that I got a good vender and will get a good one. They say they have already shipped it and gave me a tracking number. But the number is not showing up yet. Ive seen this before with china stuff. I will give it a couple days and check again.>... The next one is for the screen kit: http://www.ebay.com/itm/141653108269?_trksid=p2060353.m2749.l2649&ssPageName=STRK:MEBIDX:IT > Cant say enough good things about this vendor and kit. It looks and feels outstanding and I recieved it in two weeks from china. That is pretty darn good. Now, the only thing is since I have no power cable. I do not know for sure if I got a good one. But, like I said. It feels like a quality part. The last item is a phone repair kit that really helped with this job. The metal and plastic spudger really helped with battery and other small parts like camera and vibrator. For the price I suggest you get one. Here it is: http://www.ebay.com/itm/111501320079?_trksid=p2060353.m2749.l2649&ssPageName=STRK:MEBIDX:IT
As for the screw driver. Dont do what i did. I bought a cheapo 1.69$ one. It was crap. Lucky for me. I had one from a previous kit I bought and it worked fine. Hopefully these links will show up for you guys. If not I will try with a different browser.
Just so its clear. I do have a hair dryer that I keep for samsung screens. I thought about trying it on the cable. But I have worked on these kind before. There is a really fine line between warming the glue and melting the cable. This sucker had enough glue to hold the hoover damn together. Ive seen it before and Im pretty sure you would melt cable before the glue would give away. Thanks you guys for advise and just letting me vent. I do hope that anyone who attemps a repair can learn from my mistakes....lol. Thanks again.
I've been taking stuff apart and SOMETIMES successfully getting it back together for over 40 years, sometimes with the odd screw leftover, but hey, where do our extra screws come from eh?
I replaced the screen on the OnePlus for a friend a couple months ago and WOW, they need to make these screws JUST a LITTLE smaller, don't you think? I find that keeping a small magnet on hand comes in handy to keep track of those tiny a** screws.
pckarma112- Nice job on the post of Parts. Only problem is the first link failed. Said it was too old. Again, thanks for sharing and letting us learn from your mistakes.
Thanks for the *cough* compliments. The link is bad because seller is sold out. However, you can try this one:http://www.ebay.com/itm/111501320079?_trksid=p2060353.m2749.l2649&ssPageName=STRK:MEBIDX:IT......If that does not work then there is this:http://www.ebay.com/itm/Black-LCD-D...412?pt=LH_DefaultDomain_0&hash=item3f3f160554 This is same only black. Again, these people really treated me well. Im sure there will be new auctions when he restocks. There are also plenty of others. Price varies a little. Im really delighted that you find small screws to be a pita. Thats just awsome. lol Keeping a piece of tape on the table really helps. Just drop them on to the tape and I promise you will never lose another one. I would really like for this thread to be helpful to anyone that gets unlucky. So, I am trying to be ernest about it all. That includes honesty with no hidden attitude. When I say thanks. I really mean it.
By the time and god willing the power cable arrives. I will hit the big 60. This will not be the last phone I ever repair( I hope). But it sure has been one of the most interesting. Thanks again guys and may your screws never be loose.
Thanks
p51d007 said:
I've been taking stuff apart and SOMETIMES successfully getting it back together for over 40 years, sometimes with the odd screw leftover, but hey, where do our extra screws come from eh?
I replaced the screen on the OnePlus for a friend a couple months ago and WOW, they need to make these screws JUST a LITTLE smaller, don't you think? I find that keeping a small magnet on hand comes in handy to keep track of those tiny a** screws.
Click to expand...
Click to collapse
Thank you. You gave me a good laugh and it was much needed today. In fact. Its needed everyday in this world. The kit of screw drivers that I own are indeed magnetized. Thank God. Seriously though. If you think these are small. Try repairing a watch. Now your talking micro. I have worked on about a dozen or so with my brother. He is a master clocksman. Makes good money still and when ever he needs help. I get to learn from him and make a little too. So, Im blessed. I also lost track of where a couple screws will go on this phone. But, got it figured out. It is nice to know that none of us are perfect. Thanks again bro.