Related
I need help phone stuck in bootloader and its not registering the usb syn cable being attached I think i just need to set it to boot to os. Have HARD-SPL.
ok got usb working again but ruu says it can't find device. is that because its already because its already in bootloader?.
edit- did an info 8 in mtty and got this
Block 0x3A8(936) is BAD block !!!
Block 0x3A9(937) is BAD block !!!
Block 0x3AA(938) is BAD block !!!
EDIT- finally got home and was able to reflash os with sd card and phone works now.
but what did you do to be able to flash?
everytime I try to flash it enters the BL and hangs. Then it says it cannot update. I've got a 1.09 BL
thanks
Read here:
http://forum.xda-developers.com/showthread.php?t=286755
giving more data:
which bootloader version on your device?
1.09
which rom on your device?
1.35.255.2
which RUU are u using?
HTC WWE version
which rom are u trying to flash?
2.11.255.1
Bootloader 1.09 is not compatible with new RUU version inside HTC's 2.11.255.1 ROM.
If you just run the shipped exe file (without unpacking), it will first upgrade your bootloader to 1.11 using the old RUU, then launch the new RUU and flash your rom.
BTW, i suggest you to read the hardSPL thread before attempting to upgrade
Ok, now I noticed that incompatibilty and used HArd SPL to upgrade to 1.11.
that's what it says now in threecolor bootloader.
But still when I try to upgrade it hangs on the bootloader saying HERM200 IPL-1.01 and HERM200 SPL-1.11 and USB in the white area. And in the PC it says OS information detecttion for ever!!
If I reboot it no problem, everything is working.
thanks for you help!!
ok, now that you have HardSPL-1.11 on your device, do this:
1. Use winrar to extract the contents of RUU_Hermes_QTEK_WWE_2.11.255.1_102_6275_1.38.00.10_108_Ship.exe
2. You will see a file named RUU_Inside.exe
3. Use winrar again to extract the contents of RUU_Inside.exe
4. Run the RUU you'll find here, with device in bootloader mode.
Keep in mind that this will overwrite HARD-Spl with the shipped 1.11 bootloader, if you don't want that, read the wiki:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeGuide
Well it worked!!! Thanks a lot!!!! any explanation for this? (i forgot to tell I was using vista)
But... eheheh now I found out http://forum.xda-developers.com/showthread.php?t=297849&page=2
and it happens the same.. when I run it... (after winraring the main file) it hangs on the BL! Damn!!!
Muster said:
(i forgot to tell I was using vista)
Click to expand...
Click to collapse
boh!
I know I know awfull mistake!!!
Why does this happens when I try to update? ANd why it worked the way you said it would?
Muster said:
Ok, now I noticed that incompatibilty and used HArd SPL to upgrade to 1.11.
that's what it says now in threecolor bootloader.
But still when I try to upgrade it hangs on the bootloader saying HERM200 IPL-1.01 and HERM200 SPL-1.11 and USB in the white area. And in the PC it says OS information detecttion for ever!!
If I reboot it no problem, everything is working.
thanks for you help!!
Click to expand...
Click to collapse
uhh... it should say SPL-1.11.Oli
It did not!! It says now 1.11!!
when I tried the upgrade to WM6 it used it's own bootloader 1.09 Ds and it changed again. Is it possible that 1.09 BL is definitevely not working in my TyTN?
Dear All,
Could someone please tell me how to get the SPL back to original. Im planning to sell the phone and it basically needs to be completely as it were.
Thanks a million!
Kind Regards,
Henry
rakdoll said:
Dear All,
Could someone please tell me how to get the SPL back to original. Im planning to sell the phone and it basically needs to be completely as it were.
Thanks a million!
Kind Regards,
Henry
Click to expand...
Click to collapse
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=59&Itemid=27
Thanks to Walshieau, Todd_jg and Olipro for helping me out with this.
This guide will take you through downgrading the Bootloader (SPL) on your Hermes device
This guide assumes you already have flashed ROMs and Other components and you are familiar with the process.
NOTE: By downgrading your SPL version your device is more vulnerable to being permenantly bricked if a flash goes wrong, by following this guide through YOU accept responsibility for any problems faced due to this operation. As with other downgrade guides this is NOT intended as a guide for claiming the warranty of the device having flashed components which are not authorised by the manufacturer or carrier.
The downgrade will take the following steps, since HardSPL does not allow itself to be downgraded directly, nor does SSPL allow versions lower than 1.09 to be flashed.
The first step is to dowgrade to SPLversion 1.10.oli. Firstly download this archive and extract the files to a temporary folder, connect your device up via the USB port and allow it to connect to activesync. Run "RUUWrapper.exe" which will fire up the RUU program:
Select 'Force SSPL' and continue the flashing process as usual.
Allow the flashing process to take place and your device will reboot.
Now check the SPL has been changed by entering bootloader mode, press and hold the side ok and power buttons then insert the stylus into the hole in the bottom of the device. Your SPL version should now read "1.10.oli".
The next step is to download the SPL you wish to finally downgrade to:
SPL 1.04 (includes IPL 1.00)
SPL 1.06 (includes IPL 1.01)
Again extract the contents to a temporary folder and connect your device to activesync via USB. Run "RUUWrapper" in this new folder.
Select the RED OPTION, and TICK THE BOX.
Then flash as normal.
This will flash the final SPL version onto your device.
Verify your SPL version once this has completed by allowing the device to boot into windows Mobile and entering the bootloader as before.
Last Updated ( Sunday, 17 June 2007 )
Oszi said:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=59&Itemid=27
Thanks to Walshieau, Todd_jg and Olipro for helping me out with this.
Click to expand...
Click to collapse
And *that* is the reason we helped you, so that now you help others. One day, rakdoll will help someone else. That is why we are all here. Nicely done!
how do I do this without being able to get access to the OS? now that is a challenge, but its what i need to do :O
revert back
this is what i used to flash mine back to enable original rom to be installed ,so i could take phone back for warrany reasons
Korpse said:
how do I do this without being able to get access to the OS? now that is a challenge, but its what i need to do :O
Click to expand...
Click to collapse
Shouldn't need to access OS. You should be able to do it by putting it in BL mode... THEN plug it into the usb. Then start the updater.
Its 2.30.Olipro I need to downgrade from, and you cant overwrite olipro SPL's without using SSPL by des from inside the OS, I'm trying to find another way
Korpse said:
Its 2.30.Olipro I need to downgrade from, and you cant overwrite olipro SPL's without using SSPL by des from inside the OS, I'm trying to find another way
Click to expand...
Click to collapse
2.3 is similar to 2.1.
As MrVanx's guide points out, the key is to get from 2.1 down to Oli 1.1. That will work. His guide works - guarantee it.
todd_jg said:
2.3 is similar to 2.1.
As MrVanx's guide points out, the key is to get from 2.1 down to Oli 1.1. That will work. His guide works - guarantee it.
Click to expand...
Click to collapse
Thanks for the help, but MrVanx's guide uses SSPL by des (launched from inside the OS where I can't get to) to overwrite the 2.10.Olipro to get back to 1.10.Olipro, so that method wont work for me either
Korpse said:
Thanks for the help, but MrVanx's guide uses SSPL by des (launched from inside the OS where I can't get to) to overwrite the 2.10.Olipro to get back to 1.10.Olipro, so that method wont work for me either
Click to expand...
Click to collapse
Oh interesting. A nuance I hadn't picked up on. So, when using the Force using SSPL" option in the flashing utility, you must be able to access the Phone OS? That surprises me, I thought that the RUU utility would put it on the phone even in BL mode and execute it? Hmm... strange. I guess if it is an exe, it needs the OS to run, though. Sort of makes sense. Sorry about the misdirection.
todd_jg said:
2.3 is similar to 2.1.
As MrVanx's guide points out, the key is to get from 2.1 down to Oli 1.1. That will work. His guide works - guarantee it.
Click to expand...
Click to collapse
Hi,
I'm trying to downgrade to the original SPL (I'm trying to get hold of 2.03 but can't seem to find it), so am using 1.06. I've been able to downgrade to Oli1.10 from Oli2.10, but it won't go back to 1.06 from there, after the RUU says successfully completed the SPL is still the same.
Any ideas?
Cheers
downgrade phone for rogers warranty
Hi Guys,
I need to downgrade my phone as well for warranty purposes. Unfortunately Mrvanx's guide is offline at present. Can any one of you give little further detail about what I need to get back to orginal rom/radio/spl and bootloader. Or in shor to be able to send it back for warranty. I do have a new Rogers phone if that can be of any help.
It is from Rogers and currently my boot loader screen says following:
HERM200
IPL-1.04
HERM200
SPL-2.10.Olipro
Under Device Information:
ROM version: FARIA.R-32
ROM date: 11/06/07
Radio version 1.54.07.00
Protocol Version 32.86u.7020.23H
ExtROM version: BIGSTORAGE
My replacement Rogers Phone has following:
HERM200
IPL-1.01
HERM200
SPL-1.11
Under Device Information:
ROM version: 1.34.631.14
ROM date: 04/17/07
Radio version 1.42.00.00
Protocol Version 32.75.7020.18H
Can anyone please tell me if it is even possible to do this downgrade.
Thanks
B.
why dont you just brick the phone if you are worried about them complaining over the boot loader version. If you cant access the phone i doubt they will be able (or even be bothered) to
Could you please let me know what you did? Did you downgrade To the original Rogers Radio and SPL ? Do you by any chance have all the original Rogers files (WM5, SPL, Radio,...)?
I am with Rogers too and just unlocked SIM (not CID) and installed WM6 (official HTC)
I am wondering how I could lock SIM again if I need to return the phone for Rogers warranty? or unlocking SIM does NOT void the Rogers warranty?
Thanks
Downgrade to SPL 1.11
Hi is anyone able to figure out how to downgrade from SPL 2.10 Olipro to SPL 1.11? I have tried Mr Vanx guide but at the end of the process, I get Error 260. Not sure if I am doing anything wrong.
Do I have to downgrade to SPL1.10 Olipro, before I downgrade to SPL 1.11?
Thanks
I am having some issues downgrading back to an original SPL. I've searched throughout the site and have found a lot of conflicting advice, although this thread seems to be the most relevant.
I started out the process with SPL: 2.10.Olipro
I downgraded to 1.10.oli.
This process was successful in that the bootloader screen now says that the SPL version is 1.10.oli.
Now, when I try to flash the OEM version of SPL, the phone asks the following question:
You would like to run jumpspl.exe
If I say yes, the screen goes gray and says load... but I end up with a 260 error.
I have tried turning off the usb connection in the active sync and starting from the bootloader as mentioned here, but that just ends up giving me a 264 error.
Any suggestions would be appreciated.
Cheers,
~Hat
* edit *
Post #5 from here fixed the issue.
Oszi said:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=59&Itemid=27
Thanks to Walshieau, Todd_jg and Olipro for helping me out with this.
This guide will take you through downgrading the Bootloader (SPL) on your Hermes device
<snip>
The downgrade will take the following steps, since HardSPL does not allow itself to be downgraded directly, nor does SSPL allow versions lower than 1.09 to be flashed.
The first step is to dowgrade to SPLversion 1.10.oli. Firstly download this archive and extract the files to a temporary folder, connect your device up via the USB port and allow it to connect to activesync. Run "RUUWrapper.exe" which will fire up the RUU program:
Select 'Force SSPL' and continue the flashing process as usual.
Allow the flashing process to take place and your device will reboot.
Now check the SPL has been changed by entering bootloader mode, press and hold the side ok and power buttons then insert the stylus into the hole in the bottom of the device. Your SPL version should now read "1.10.oli".
The next step is to download the SPL you wish to finally downgrade to:
SPL 1.04 (includes IPL 1.00)
SPL 1.06 (includes IPL 1.01)
Again extract the contents to a temporary folder and connect your device to activesync via USB. Run "RUUWrapper" in this new folder.
Select the RED OPTION, and TICK THE BOX.
Then flash as normal.
This will flash the final SPL version onto your device.
Verify your SPL version once this has completed by allowing the device to boot into windows Mobile and entering the bootloader as before.
Last Updated ( Sunday, 17 June 2007 )
Click to expand...
Click to collapse
Okay, Im back to 1.10oli, but how do I know if I need to go back to SPL 1.04 (includes IPL 1.00) or SPL 1.06 (includes IPL 1.01)?
OK people, please tell me you have looked at the updated guide right??
http://www.mrvanx.org/thg/index.php?option=com_content&task=view&id=19&Itemid=27
Yes, but the choices are,
1.04
1.06
1.09
1.11
2.03
and I don't know how to tell which one is stock for my phone. I assume I need 1.04 since my bootloader says IPL-1.00 but I'm not sure because I know that used to say IPL-1.04, and since it appears that that can change for some reason, I want to make sure I get this right so I can get this waranteed. Im going to sell it on ebay and get the new HTC Fuze as soon as AT&T releases it.
I'm running vp3G latest ROM and wanted to install a radio. I thought I could install the latest 1.54 but when I do it locks up at 0% and then gives me the 262 error message. The wiki says I should have bootloader 1.04 or HARDSPL. I thought I did. Can someone help me out as to what radio will work and what are the steps to upgrading?
Thank You
Read my specs. I have the same rom you do. should work
1.54.07.00 works
1.54.07.00 works well with vp3g's roms
If you can't be past error 262, here's an option:
Copy "SSPL-HERM.exe" to your miniSD then run it from the phone.
Your phone will reboot into the BL (tri-color screen)
Connect your phone via USB to your computer
When AS finally pops up, click cancel
Run RUUWrapper.exe and force SSPL
That should do it.
MontyV77 said:
I'm running vp3G latest ROM and wanted to install a radio. I thought I could install the latest 1.54 but when I do it locks up at 0% and then gives me the 262 error message. The wiki says I should have bootloader 1.04 or HARDSPL. I thought I did. Can someone help me out as to what radio will work and what are the steps to upgrading?
Thank You
Click to expand...
Click to collapse
1.48.00.00
i installed the wrong rom on the wrong hard spl. i had the hard spl a 1.30 installed and dcd 3.2.0. now the screen is stuck at the loading screen that says htc smart mobility. and no radio at the bottom. please help and the phone wont sync.
Good luck on that.. You installed a bootloader for a different model -- likely the TyTn or Trinity. What phone do you have? What instructions did you follow?
If you do have a Titan, then possibly via the SD Card you can change the bootloader to the new 2.47 (I haven't played with it yet but another may provide a solution). You are likely out of luck in flashing to any of the other Titan bootloaders as you must be able to boot into the OS, but with you error of installing an inappropriate bootloader you are out of luck there.
no it was a bootloader 1.30 for the titan
Your information is incoherent.
What rom/bootloader did you have prior to updating?
What rom/bootloader did you try to upgrade to?
You need a minimum SPL of 2.40 to install DCD 3.2.0
I use 2.47 from no2chem and it works great. http://forum.ppcgeeks.com/showthread.php?t=30561
Are you able to boot up the device? If so copy the SPL 2.47 to the card then to the PDA and run it from there.
If not, put the PDA into Bootloader mode and try to install Olipro 2.40
http://www.lifesnotsogood.com/dcd1182/titan/spl/titan_SPL_2.40-olipro.exe
Failing that you can try to flash back to an official ROM if you have one.
You need to soft reset your phone while holding the Camera and power buttons. This will force your phone in to the bootloader. You should then be able to reflash to lower ROM. Then you need to search for Olipro or whatever the 2.40 bootloader is. Your best bet after that is to flash the official Sprint 3.35 Radio and Rom then flash to DCD's.
**Edited**
Sorry Hamilton didn't realize you gave a link to the 2.40 bootloader.
If he is sure that it is "bootloader 1.30 for the titan" then I know of NO such bootloader. He has likely installed the wrong bootloader (for another device) and therefore no amount of flashing to an OS ROM will help him boot into the OS. Unless via an SD card for 2.47, beastmode216 is stuck with a borked device.
So, beastmode216, I'll ask again, where did you get such instructions and where did you source your bootloader 1.30?
What is one of the earlier bootloaders? I was thinking my Mogul orginally had something like 1.30 or 1.40.
thanks guys but the problem is solved. just make the phone go in to the bootloader
Verizon stock bootloader is 1.30 if I remember correctly. It has been several months since I have seen a stock bootloader
calash said:
Verizon stock bootloader is 1.30 if I remember correctly. It has been several months since I have seen a stock bootloader
Click to expand...
Click to collapse
My mistake, as pointed out by gc14 the stock bootloader is 1.04.
Ahh, ok, my fault as I thought that he had also installed a bootloader under the name of 1.30.. That could've been an unlocker for a TyTn or another device.
Correct, OEM bootloader should be 1.30.60.
Click to expand...
Click to collapse
This is incorrect. The stock bootloader is 1.04. The stock radio is 1.30.60.
SPL 1.30 does NOT exist for the Titan.
Stickies exist for a reason...to read them as they contain valid, useful information. http://forum.xda-developers.com/showthread.php?t=392133
I accidentally flashed the titan using olipro 1.2, and the new unlocker, and I cannot get past the verizon boot screen. This is a fresh new 6800. when I start it it says:
p DCAAXAM-4350
R 3.42.30
D 2.17
The bootloader screen says Tita100 spl-120.olipro
the only way I can flash is via the sd card. I cannot connect via activesync.
how do I fix it?
this is a warranty replacement, so I need to get this to work before I restore my old 6800 to factory settings, and return it to verizon
thanks
whiteblazer01 said:
I accidentally flashed the titan using olipro 1.2, and the new unlocker, and I cannot get past the verizon boot screen. This is a fresh new 6800. when I start it it says:
p DCAAXAM-4350
R 3.42.30
D 2.17
The bootloader screen says Tita100 spl-120.olipro
the only way I can flash is via the sd card. I cannot connect via activesync.
how do I fix it?
this is a warranty replacement, so I need to get this to work before I restore my old 6800 to factory settings, and return it to verizon
thanks
Click to expand...
Click to collapse
Can you not put the phone in bootloader mode (power+camera+reset) and connect via USB? Even though activesync doesn't see it, it's still possible for RUU updater to connect. I had a similar problem before. Try doing this and putting Hard_SPL 2.4 on it.
Look at section II on this wiki... it says if you have 1.20 olipro... flash to an older rom and radio... WIKI
Snippit.... " if it is 1.20 then you have the pre-GPS ROM bootloader and must first flash to one of the older ROMs and associated radio to boot into WM, get an ActiveSync connection and then upgrade to 2.40. "
nitro66215 said:
if it is 1.20 then you have the pre-GPS ROM bootloader and must first flash to one of the older ROMs and associated radio to boot into WM, get an ActiveSync connection and then upgrade to 2.40. "
Click to expand...
Click to collapse
Hes right, you need to load an old pre-GPS rom on your phone, then upgrade. I've had this happen myself.
Yes, this is what I saw too, however, all the roms I found on this page http://wiki.xda-developers.com/index.php?pagename=TitanOtherHome for the olipro 1.20 take me to an internal server error on fileshex.com. I can't find any rom file that I can actually download. Does anyone have a link to one or can you upload it? I suppose it doesn't matter which one it is, since I'm going to upgrade from there.
I just cooked an old 1.6.7 rom for you...wow did it bring back old memories.
Download 1.6.7 rom here: http://www.cinconet.org/titan/dcd 1.6.7 Rom.zip
Download 1.30.60 radio here: http://www.cinconet.org/titan/Titan Radio 1.30.60.zip
Put radio .nbh on the root of the card with a card reader. Force phone into bootloader and flash radio first. When it completes, remove the microsd card and replace the radio .nbh with the rom .nbh with the card reader. Insert the card again, force bootloader, and flash the rom. Remove the card and soft reset.
WOOOOOOOOT!!! it worked! Thanks gc14 for the files and awesome instructions!