Good afternoon,
I have an HTC TYTN , I have upgraded it more than twice with different ROMs without any problem.
This time, I have upgraded it with another ROM , and the process turns my phone off at 1% (and says corrupt ROM file) , vista is my OS, I never had trouble upgrading from it... except this time.
I cannot read the version of my phone anymore but the version of the new ROM . I entered my boot loader , (I have SPL-2.03) in order to flash it. I could see the upgrade process , but at 1%, my phone turns off.
what can be the problem ???.. Any help is really welcome.
Dude, theres a reason that "Flash Hard SPL V7" is plastered all over this forum....
Try reflashing your stock rom. If you recover it then FLASH HARD SPL V7...
Not all roms are able to be flashed because of your CID (Carrier ID), it won't allow an unofficial rom to be flashed. Hard SPL is a work around allowing "cooked" roms to be flashed.
Cheers...
Related
FIXED! Read below for details.
So i've been messing with my mogul for nearly 4 hours now trying to convert it to dcd's rom..and i've flashed it twice now and after it reboots from being 100% loaded it just sticks on the HTC black screen..I've read and read and searched and searched and cannot find a definite answer. Can anyone help?!
basics?
did you load the radio rom?
did you load the unlocker?
you may need to restart the phone to the boot loader and resend the rom
(press and hold camera and power and push reset button)
I did TRY and reload the radio and unlocker..now im stuck at the black htc screen where it says no radio though. bleh. i can't even get it back up and running. what do i do?
edit:
I'm at the multi color screen..ive tried running the unlocker RUU and then running dcd's ruu and it doesn't work..and the radio RUU does not run at this screen...I can't get the phone back to a working status! Argghhhh. It wont let me run the relocker unless im in activesync...but i can't be recognized in activesync unless the phone is up and functional..so..? how do i relock it to put hte stock rom on to try and unlock again?
I am kinda stuck in the same spot, but mine is is the verizon logo screen, i tryed doing the power,camera and hte reset button but its till stuck, i tryed the relocker but i need to be in active sync
any help?
what i dont get is..i flashed it with the unlocker, then the rom then the radio...isn't RUU just overwriting each one or something? it doesn't make sense to me. and all i can do is run RUU..i did the rom, then the radio and it was stuck in the bootloader so i used the exitbl and got out of it but then it just went back to going to the HTC black screen saying no radio. ..i'm gonna try and flash the rom from a sd card next..we'll see what happens..
jkrolcz said:
I am kinda stuck in the same spot, but mine is is the verizon logo screen, i tryed doing the power,camera and hte reset button but its till stuck, i tryed the relocker but i need to be in active sync
any help?
Click to expand...
Click to collapse
This just happened to me after flashing the ROM but not the RADIO yet. Flashing the Radio fixed the problem.
I've flashed the radio..then its stuck in the BL and i use the program to get me outta it then it just keeps saying i have no radio! what the hell..this sucks. i'm in the worst possible situation to have to buy a new phone
There are three parts to the "operating system" of your phone.
1. Bootloader (also called locker, unlocker, re-locker, SPL)
2. Radio
3. ROM
The three components are saved in discrete portions of the device's memory. Flashing one does not overwrite the others. All three must be compatible for the phone to operate properly. If you stop the upgrade process recommended by the ROM compiler prior to completion, your phone may not operate properly. If you flash the "leaked" 3.16 ROM package, it contains all three components.
To use the 3.16 stock OEM ROM, or a custom ROM based on the stock OEM 3.16 ROM, you must have a level 3.xx radio and a level 2.xx bootloader. The current implementations of those are the 3.27 radio and either the stock bootloader distributed with the "leaked" 3.16 ROM package, or the Olipro 2.40 unlocker.
If you are running a level 2.xx stock OEM ROM, or a custom ROM based on a stock 2.xx OEM ROM, you must have a level 1.xx bootloader and a level 1.xx radio.
Custom ROMs are not always named using the OEM convention, so you must research the custom ROM to determine whether it is based on a level 2.xx or 3.xx stock OEM ROM.
I hope this helps all of you get your phones back up and running.
FIXXXED!
So heres the best description I can give of what was going wrong for me..Its my first time trying flash to a different rom..and well it didn't go so well. First, I used the titan unlocker, then installed the radio (not sure which one) and then some form of the newer dcd rom and i was getting stuck on the black HTC smart mobility splash screen where it said "no radio". I had to have messed around for over 5 hours today at college trying to figure it out by doing different arrangements what order i installed the radio and unlocker and rom in. I couldn't get it to connect with activesync so i couldn't use the titanunlocker.exe..all i was going off of was RUU's. Im not sure whether or not what OS I was using effected it..I was playing in Vista earlier today but had done the correct steps to install the drivers, and now this last time i did it on XP. This last time I ran the 3.27 radio RUU as found.. here ( http://forum.xda-developers.com/showthread.php?t=362563 )...Theeen I ran this form of the newer sprint ROM. (I'm pretty sure they say it comes with a included in this RUU, but i'm just stating exactly what I did) the .651 rom can be found.. HERE ( http://forum.ppcgeeks.com/showthread.php?t=16806 ) He had a error when packing or something so you have to manually rename it to .exe because it was missing a e..I did this within winrar before extracting..ran that and about 10 minutes later it booted up and i've got service. I'm not going to promise that this is 100% functional all i'm saying is im out of that horrid black HTC screen where I can now go on to try and get the correct rom i wanted. Hope this helps..may be a bit confusing and probably did things wrong but this was my first time doing it all.
I recently tried to flash my 8525 with the more stable roms out there, BLINKY 3.5, PDACorner V.11. Everytime i try and load the RUU my devices starts the process but kicks out after 1% everytime and tells me that i have a corrupt image file.
I suspect the issue is with my spl version. I have 2.04 and the installer i think needs atleast 2.11.
How do I upgrade to that from where I am now?
Thanks
Make sure that you have got a full rom download. Also flash on Hard SPL. This is found in the upgrade section. Its a must as it "supercids" your device making it possible to flash non stock roms...Please note however that if your hermes is still under warranty it will void it.....Cheers...
I'd just like to jump in and say I was having the SAME problem, even with the same ROMs and I did as mentioned above.... Upgraded Hard SPL and when given the choice of how to flash choose the one that says 2.10 and check Hard- SPL.
Thanks for all the help here, these forums are life savers.
Personally, I prefer the sd card method to using the pc... I find it safer with 100% success rate...
Cheers...
Anyone experienced this situation? Half year ago i have made Hard-SPL for my wizard because my 2 year warranty at T-Mobile finished. After i made Hard-SPL everything went good, i flashed many roms with no problem. My last rom is Slim Diamond edition which i wanted to change for new TNT now. But i cannot get to bootloader through RUU and i tried to get there manualy but my Wizard always freezes on a black screen. I have to get out the battery, wait few second, push battery back, and switch on the device. My wizard boots normaly, OS works normaly and i can do everything with no problem. But flashing is restricted area now! Anyone know what to do with this ?
Ok i find the solution by myself. It seems like that Hard-SPL do not really unlock wizard to flash any rom you want. All i had to do was to flash original ROM, from manufacturer, but the original ROMs usualy contains IPL and SPL which would brick the device if it is Hard-SPLed. So i tried to extract the original ROM, removed IPL and SPL images, and tried to flash just OS but flashing process was stuck every 43 % and i had to remove battery and start again. So this was not working too :-( So one czech ROM cooker helped to flash his ROM 1.1 CID-locked editionwhich contains only OS, splash screens and ExtROM. Maybe here presented LOVE Rom should wotk to. So all i must do before flashing new WM6.1 ROM on Hard-SPLed Wizard, is to flash original rom without IPL and SPL (it is important!!) and then i can flash everything i want. If i do not do it i cannot enter the bootloader to flash. Maybe it is normal but i did not read it before, all cookers recomends to flash original OS before flashing new one, but i thought it is just for to be sure that all will be flashed well.http://fenix.metronet.cz/johnny/download/ROM 1.1 CID-locked edition by ppctuning.org.exe
My phone is running on
OS VERSION:5.2.23569
MANILA VERSION:2.5
ROM VERSION:Cruzer 5th WWE
Radio Version:2.15.50.14
I've had enough of using the Cruzer 5th rom already and wish to update back to the normal Official HTC ROM. I've downloaded the RUU_Updates for both 1.66 and 3.14 and both have failed in updating the phone's ROM.
The problem is that once my cpu has detected the phone.
The phone will then reset and get's stuck on the screen which has a few colors.(The one we use to check our HD2's flash version like HSPL). Then the loader on the screen of my CPU will be stuck at 0%. And guess what...before you know it...the entire operation will cancel and it will say that its not able to update my ROM. What on earth? Please help me. I'm only not able to update back to the official rom software. Apart from that,the other cooked roms which have been made available for download from the other users can be used to update my rom.
I need help. Please help me. Thank You! i look forward to your solutions!!!
You can use other roms and if you look/use the search option your answeres are here somewhere
could be a stuck radio rom, there have been several examples where the radio prevents spl and radio (and hence stock roms) from flashing.
try your CORRECT stock rom from sd card flash, if that fails its either
1 - not actually your correct stock rom or
2 - you are flash stuck. no clue how you would solve that.
LekHD2 said:
Then the loader on the screen of my CPU will be stuck at 0%. And guess what...before you know it...the entire operation will cancel and it will say that its not able to update my ROM.
Click to expand...
Click to collapse
I had the same problem like u 2day. All I did was instaling SPL-3.03.HSPL
At first I had two options like SPL-3.03 or SPL-3.03.HSPL to instal, that first one was making the problem that you writing of, but after I instaled SPL-3.03.HSPL I can instal other roms.
LekHD2 said:
My phone is running on
OS VERSION:5.2.23569
MANILA VERSION:2.5
ROM VERSION:Cruzer 5th WWE
Radio Version:2.15.50.14
I've had enough of using the Cruzer 5th rom already and wish to update back to the normal Official HTC ROM. I've downloaded the RUU_Updates for both 1.66 and 3.14 and both have failed in updating the phone's ROM.
The problem is that once my cpu has detected the phone.
The phone will then reset and get's stuck on the screen which has a few colors.(The one we use to check our HD2's flash version like HSPL). Then the loader on the screen of my CPU will be stuck at 0%.
Click to expand...
Click to collapse
I know you said you downloaded the two ROM's from the HTC website. I don't know if you have a TMOUS HD2 then I suggest downloading the official upstream ROM from the T-Mobile website it is the 3.14 ROM.
I think what has happen to you is you had a bad flash and if you flash the 1.66 ROM first then you changed your SPL and now you don't have the correct split to flash the flash the 3.14 ROM. I recomemd you download and use HSPL 4 to change your SPL to SPL 3.03.0000 then try to flash the update ROM. Or you could flash it via your SD card that should force the changing of your SPL with out you doin yourself. JUst my thoughts on the situation.
This is my first thread so I hope Im not double posting with my question. I am trying to get my HD2 back to stock, I have downloaded the official t-mobile rom from htc. Whenever I try to flash ROM from sd card or any radio it gets stuck at 96% or 99%. I have tried hspl 2.08 and if I do 2.08.0000 nothing will flash at all. I am at my wits end because I have tried every suggestion and have searched high and low through the threads. Any help is appreciated.
Hey! If you installed some other roms (wm, wp or android) you need program task 29!
It will clean your flash memory. After that you need to know what was the original spl on your phone (like 2.08.0000 or 3.05.0000) SPL, not HSPL! Flash your stock SPL! reboot, enter in bootloader again and connect phone in to pc, flash your stock rom while you in bootloader through pc! It works for me 100% Enjoy)