can someone kindly walk me thru upgrading my AT&T 8525 firmware or software. I originally received it w/ WM 5.0 later I upgraded to original Microsoft WM 6.0 . eversince, I tried flashing w/ cooked software ROM but it wont accept any flashing. I was told, I have to use a specific file to flash it, then I will accept any cooked software (ROM) . I apologize, I'm new in this matter, not even sure if I'm using the correct terminology. but bottom line I want to use other software other than the Microsoft WM 6.0. many thanks to everyone. rustyjack67
Mate, read this - http://www.mrvanx.org/guide/hermes/upgrades/hardspl
Then this - http://www.mrvanx.org/guide/hermes/upgrades/rom
Then this - http://www.mrvanx.org/guide/hermes/upgrades/radio
This should set you right.
To upgrade your SPL to Hard SPL V7 using the sd card method go to page 116, post 1160.
You can use the sd card method AFTER installing Hard SPL V7 for ROMs, just drop the steps using SSPL.exe.
Cheers...
many thanks Ultra .................
many many thanks to you Ultra....... , i will check, read and follow the guide per your referral, I will post for result , chow........... rusty
unable to run custom RUU....... help
hi there Ultra ,
is this what you mentioned? http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing
I'm still in the process of researching and learning the lingo's being used ............
by the way this is what I've found out on my 8525
HERMES
IPL-1.01
HERM100
SPL-1.40 olipro
someone from forums mentioned it's better to use an XP OS in fllashing than Vista OS. what's your opinion? I'm sorry I just want to be sure , I don't want to brick my phone. . many thanks. rusty
rustyjack67 said:
hi there Ultra ,
is this what you mentioned? http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing rusty
Click to expand...
Click to collapse
Yep, Thats fine for ROMs, but the link I gave you will take you to the thread on Hard SPL installation using the sd card method. Its sllghtly different.
rustyjack67 said:
by the way this is what I've found out on my 8525
HERMES
IPL-1.01
HERM100
SPL-1.40 olipro rusty
Click to expand...
Click to collapse
You need Hard SPL V7. You SPL needs to be 2.10 oli. The thread I gave you will allow you to download it, its on the 1st page (about the middle - just look for Hard SPL V7).
rustyjack67 said:
someone from forums mentioned it's better to use an XP OS in fllashing than Vista OS. what's your opinion? I'm sorry I just want to be sure , I don't want to brick my phone. . many thanks. rusty
Click to expand...
Click to collapse
Mate, there are dangers no matter what you use but I find the sd card method safest. Just make sure you have a charged battery, a 2Gb sd card formatted FAT32 & make no spelling mistakes - hermimg.nbh . About the only way you can stuff it up is to not have Hard SPL V7 installed and if you reset in he middle of the flash. A charged battery is a must, don't think you can charge it while it flashes, it doesn't work.
Happy flashing.... Man that sounds dirty...
Cheers...
This must the one your talking about.........
#1160 22-03-2008, 11:25 PM
XtreMe_G
Senior Member Join Date: Jan 2007
Posts: 1,131
--------------------------------------------------------------------------------
ok, lets see if i get this right.
1. download hardspl v7 from the first post.
2. extract ruu_signed.nbh and rename it to HERMIMG.nbh
3. copy it to a microsd card, make sure the card is formatted as fat32
4. download sspl-herm from here
5. extract SSPL-HERM.exe and copy it to your phone.
6. insert sd card and run sspl-herm.exe on the phone.
7. you should see the tri-color screen and then it should change to this
8. press power button to start flashing
9. reset when you get the msg that its done.
so far I've got everything needed including the hard SPL-V7, SSPL-HERM.exe, micro SD formatted to FAT32..... hopefully I get this in one shot, wish me luck, any last warning? by the way many thanks to you ULTRA, your my hero . this phone is for my " old lady, hopefully If I get it right, I might get a little extra" you know what I mean!!!!! chow ................... rusty
No problem, you go big boy...
Cheers...
I did everything right,
When it says to press the power button,
I press it, nothing happens.
I don't think im doing anything wrong, i've been trying this for 2 hours, and im very frustrated.............
You need 2Gb or less sd card.
It has to be formatted FAT32.
The .nbh file MUST be renamed hermimg.nbh and MUST be a rom for the Hermes.
As long as these 3 things are right you should have NO problems, however, if just 1 thing is wrong then you won't be able to upgrade ANYTHING...
Cheers...
Related
Hi all,
i've found an alternative approach to flash any firmware on HERMES 200.
I had a problem while i was trying to upgrade my WM5 Vodafone 1605 to WM6.
My bootloader is SPL-1.09, and i've tried in many ways to install Hard-spl v7 but here is what was keeping happening:
- I try to flash my Hermes with hardSPL v7 and each time:
- Hermes switch to bootloader mode and display
HERM200
IPL-SSPL by Des
HERM200
SPL-1.09.ds
- Activesync lose the connection
- Windows XP send popup with new USB device and ask me to install the new device (no idea of driver not found by default)
- RUUWrapper display error 260
Click to expand...
Click to collapse
Here is the solution:
- Download the firmware u wish to install on your device
- Unpack the firmware (right-click and Extract)
- copy the .nbh file into you microSD card and rename it as: HERMIMG.nbh
- put SSPL-HERM.exe into you device (you can get this app in this site too)
- now put you microSD card into you device and run SSPL-HERM.exe
- enjoy
I'm just an unexpert user that has tried many times to upgrade his device reading other posts on this forum. So pls correct me if i've said something wrong!
I wrote this post just cause i was going crazy and i wasn't able to find a solution like this around the sites
Hope this help somebody!
PS: I'm sorry for my bad english!
RUUWrapper display error 260? try to disable your firewall, flash again, and you will see it works.
regards chief
i've got the same problem with my hermes...
i don't know how to fix...when i start the flashing process the device switches in the bootloader mode and then nothing else is happening, there is no connection to the pc. i tried to switch off the firewall, i changed the cable, i changed usb port but nothing happens...
does anybody know what i shall do?
its the same fault as anvillani describes, the only thing different is that i dont get herm200 but herm300
Do you guys do ANY research before trying this???
Go to this thread - http://forum.xda-developers.com/showthread.php?t=296722
Go to page 116, post 1160 and READ it step by step, juymp ahead and this WON'T work. Just make sure you use a 2Gb or less sd card. INSTALL HARD SPL 1st.... Then you can use the sd card method (just skip the steps using sspl.exe as you should now have Hard SPL) to update your roms....
Cheers...
i really dont know what you want to say with this...
i tried the normal procedure to flash hard spl to my device and i tried the method anvillani suggested and both didn't funtion.
so my question is what i should do...
Follow the link and instructions in my previous post. It will allow you to install Hard SPL using the sd card method. You do need to be able to get to the today screen though.
After reading anvillani's post I'll add that the sd card MUST be 2Gb or less and has to be formatted FAT32. You have to name the .nbh file hermimg.nbh with NO speeling (sorry, spelling :b) errors or it won't work.
Cheers...
Hi All,
I'm new to the PDA-world and the Hermes. I'm trying to Hard SPL my Hermes, but it fails everytime.
When I run 2.10 - Hard-SPL-V7, it kills activesync and my connection is lost and I get always the message "error 260, Update error".
I have the latest framework edition and tried it on 3 pc's (1 Vista, 2 XP)...
What am I doing wrong?
Hope somebody can help me....
Kind Regards,
Micha
1). dont connect to active sync. open active sync and untick "allow usb connections".
2). put hermes into bootloader and connect to usb.
3). run ruu_wrapper.exe
should update to hard spl....
dont forget to tick "allow usb connections" again or you wnot be able to sync..
error 260 is an open port error.
if you wish to flash new os would advise to use sd card method. its safer than using the computer. just make sure you have greater than 50% battery power. happy flashing
Thnx, will give it a try.
First I have to flash HardSPL before I can flash a new OS, don't I?
yep, sorry, should have said run the ruu_wrapper for hard spl. My bad...
im having the same problem. I also tried the way ultramag recommended but i also received the same ending. After time i try i get the Error 260 Update error. Im running SPL 2.04 and the HTC WM6 rom from the HTC website. Does any one know what the problem is?
ultramag69 said:
2). put hermes into bootloader and connect to usb.
Click to expand...
Click to collapse
NOOOOO, that won't work, you need the SSPL to deploy to the phone, if you're running stock HTC bootloader this won't work at all, otherwise we'd have no need for Hard-SPL
hey olipro, then how would i fix this. Im running the stock rom from the HTC website with no hacks. Im trying to load PDA Corners V9 rom. Any ideas on how to fix? thanks!
Take a peek at the guide i wrote about updating the hardspl. Theres some explanation about why we need to use SSPL and the procedures.
http://www.mrvanx.org/hermes_guide/hardspl
thats the guide i used. it still gives me the error. I even unchecked "allow connections" cause i read somewhere that that would help.
i did this two days ago on my phone, im running windows vista on my home laptop and got any number of errors and problems trying to do it via sync with the phone (even after reading the vista troubleshooter, with the drivers etc)
What i ended up using was the memory card upgrade, dump the file onto the memory card and go into bootloader with the card installed.
worked fine doing that way, maybe less risky as there is no chance of the usb cable coming out.
just make sure you have a good battery charge on the phone.
Help Help Help w bricked 8525
I got into this position trying to upgrade WM5 to WM6 from HTC site.
Process got to 20% and just stayed there.
I reconnected usb cable and got a vendor id error
Then I get the Error [260]: CONNECTION
I have read a lot of posts and have tried the sd method (although i am not 100% clear) and all i get is the screen with four colors, red, green blue and white.
I believe this is the bootloader? I have downloaded RUU_signed.nbh, renamed it to hermimg.nbh, installed on root of my SD card and held OK, soft reset and power button:
My display reads:
HERM100
IPL-1.04
HERM100
SPL-2.03
This is where my journey ends.
All post indicate that the device can be reflashed and have the OS reinstalled. I can't get there from here.
Can anyone please help?
blackdog9692 said:
I have read a lot of posts and have tried the sd method (although i am not 100% clear) and all i get is the screen with four colors, red, green blue and white.
Click to expand...
Click to collapse
How big is your SD card? Flashing only works with cards <2GB. Also, sometimes certain cards just don't work for flashing, and just swapping to a different card fixes the problem.
I assume you searched the wiki, and found the relevant pages on the Hermes (including SD Card Flashing and other things about flashing/upgrading) there?
Still Lost
My SD is 2GB and I have tried many times but i just keep getting the 4 color screen. rt now when i boot from the SD my screen goes white and displays "Loading..." and then returns to bootloader screen. When i attempt to flash the rom via PC to WM5 or WM6 i get the Error 260, i also get a vendor ID error sometimes.
How can i find the key 8525 thread that i am told has the answer to my delima? I keep picking up bits and pieces but am missing some key steps and tips.
blackdog9692 said:
My SD is 2GB and I have tried many times but i just keep getting the 4 color screen. rt now when i boot from the SD my screen goes white and displays "Loading..." and then returns to bootloader screen.
Click to expand...
Click to collapse
That sounds like the SD card is formatted incorrectly. Make sure it's formatted using fat32, nothing else will work.
Still not there from here
Thanks for your help. Before I formatted the SD FAT32, nothing would happen doing the bootloader reset. OK/ON/reset button.
After format and only the hermimg.nbh file renamed as indicated, I then get what looks like the loading process but back to the bootloader screen.
Q1: This is an AT&T 8525, it was perfectly fine before failure from WM5 to WM6 (process froze at 20%), what is the RUU file that I need to put on SD??
Q2: After "Loading ..." I try the WM5 PC upgrade of ROM via USB cable, I get the load process to appear to work but it gets to 1% and the phone reboots and the PC reports error [294]: Invalid vendor ID. If I do this again I will get the Error [260]. Ive repeated the process several times.
Is this the normal course to take or should the "SD Method" (with the WM5 or WM6 RUU.. file) complete the process to a working OS?
Q3: Is my situation hopeless? ATT will take my out of warrantee 8525 and reflash for $129. Reading the threads it seems that like me this can be done by me, this is my desire.
Q4: I still am confused by some basic terms and assumed steps. I dont understand "Hard SPL" or OLI's IPLs/SPLs and when and when to use them.
The newbe guide has been off line. I will look again. Is there a single place to read about "radio PDAs and the 8525 and understand the software build and custom options?
Sy for the long post. But still want to fix if possible or I will be force to mail in for ATT repair.
Thank you all.
blackdog9692 said:
Q4: I still am confused by some basic terms and assumed steps. I dont understand "Hard SPL" or OLI's IPLs/SPLs and when and when to use them.
Click to expand...
Click to collapse
Oh boy, you haven't installed HardSPL? You are walking a bit of a line there mate...
HardSPL is a custom boot loader that makes bricking your phone when flashing much harder to do, and helps large amounts in the recovery process if you phone does brick.
Does the phone boot at this point? If so, do not try flashing the phone again. Go get a copy of HardSPL and install it, then try flashing from the SD.
I still wonder why people didn't read before bricking...
Anyway, you should start reading now and wiki is your friend. Your SPL is 2.03, so look at the bottom of the page (there is only one solution till now, so good luck with that):
Code:
1. Boot OS using KITL+PB
2. Do no disconnect your HERMES till the end of the step 6
3. Download SSPL on HERMES by wifi from ie explorer
4. Launch SSPL then flash Hard-SPL from your computer
5. Put your hermes in bootloader mode
6. Flash any radio in NBH format from your computer
Still researching and working this bricked 8525
Thanks for coming to my aide. I believe that I have Hard SPL'd my device. I downloaded Olipro's Hard SPL v7. extracted the RUU_ file and renamed to hermimg.nbh.
I then put it on an SD card and held the keys and reset. The device displayed a white screen and "Loading..." appeared. Afterward the 8525 returned to the stipped boat loader screen and that is where I am now.
Some of the help i receive and read on wiki threads has me confused with what to do next and how "exactly" to do it.
It does seem that I am not alone and people have fixed their phones and the process to do this is on the forum. I'm just still missing something.
Help me further if u can.
Thank you.
blackdog9692 said:
Thanks for coming to my aide. I believe that I have Hard SPL'd my device. I downloaded Olipro's Hard SPL v7. extracted the RUU_ file and renamed to hermimg.nbh.
Click to expand...
Click to collapse
FYI: bad form to PM someone and post the same thing here. Keep it in the thread so others can be helped as well.
As I replied in the PM, if I'm understanding your post correctly, the phone boots to the tri-colour screen?
What text is showing on the screen? This will tell if HardSPL is on the phone or not.
jdc said:
What text is showing on the screen? This will tell if HardSPL is on the phone or not.
Click to expand...
Click to collapse
We already know that the phone is without HardSPL, according:
My display reads:
HERM100
IPL-1.04
HERM100
SPL-2.03
This is where my journey ends.
Click to expand...
Click to collapse
There is small chance (read my previous post) to unbrick device with SPL2.03 so better try to get this back from where you take it.
And please, change topic, because this brick isn't HardSPL fault at all.
Edit: oh dear, it's even not your topic ...good game, I'm off
Hello,
I would like to upgrate Rom with this one: Schaps_WM6Pro_Hermes_4.31_WWE_Full.exe
I installed Hard-SPL and now I have 2.10.olipro SPL version displayed in the bootloader (before I had 1.4).
Actually, in my Hermes300 I have installed :
WM6.0
ROM: 2.54.258.2
ROM date: 07/06/07 (DD/MM/YY)
RADIO: 1.47.00.10
Protocol: 32.80.7020.20H
ExtROM: 3.54.258.102
I don't know if it is the original ROM upgrade from HTC website, because I'm not the firt owner of the phone.
Anyway, If I try to upgrade it by using autodetect mode an error occurs:"Error, Unknown version! You should pick safe SSPL".
Why? What Do I have to do to have Upgrade? Maybe, is there still some kinda of "brand"? Which option should I have to select?
I want to use the most safe upgrading procedure to avoid brick.
P.s. I'm using Windows Xp.
Thanks!!
Pick safe SSPL..... Follow the instructions after OR use the sd card method.
Format sd card fat32 then copy the .nbh file onto it. Rename it to "Hermimg.nbh". Put it in phone and reset to bootloader. Hold down power button, ok button above flywheel and reset with stylus. Hold all buttons in until you get to tri-colour screen. It should recognize the flash image so then follow the prompts.
Find this safer than pc flash.
Cheers......
Thank you very much I will do it!
But I'd like to understand why autodetect mode doesn't work! Do u hava any ideas? Cannot I choose SPL-2.02./2.10/2.30 New Bootloader and is it HARD-SPL choices? I'm a newbie in upgrading and I only understand that to avoi brick I should use HARD-SPL. If I use Force safe SSPL or SD card method can I have a brick?
How about if autodetect doesn't work because I have installed original ROM upgrade from HTC? It is possible?
Thanks.
No flashing method is a guarantee of success. Hard SPL isn't either, it just makes it easier or even possible to fix your phone. If you interrupt a flash you will brick your phone but with Hard SPL its possible to fix. Except if you interrupt the radio rom portion of the flash. I think its OK to say that if you stuff up this part of the flash you won't be able to fix easily, if at all.
Most, if not all, cooked roms DON'T have a radio rom inside. ALL stock roms do.
This is why I said its safer with sd card method. You would have to physically reset the hermes in the middle of a flash to stuff it. With the pc, usb cables can be unplugged, reset buttons can be pushed and blackouts/brownouts do occur. Thats if Activesync doesn't throw a hissy fit and disconnect while trying to update....
>HARD-SPL just makes it easier or even possible to fix your phone.
Ok, and by using SD CARD procedure is it the same?
I mean...now with HARD-SPL installed on hermes can I use every upgrading procedure to fix my phone (if possible)? Or to take advantage from that do I have to use a particular procedure?
Before writing here I read a post where another guy had my same problem and some people answered him to choose SPL-2.02./2.10/2.30 New Bootloader and is it HARD-SPL. But u think is better by SD CARD.... .
Thanks, and I'm sorry for many questions!
Does Schaps_WM6Pro_Hermes_4.31_WWE_Full.exe have a radio rom inside? I can upgrade only Rom without RADIO? If yes...how?
Thank you very much!
No, Schaps_WM6Pro_Hermes_4.31_WWE_Full doesn't have a radio rom. Look at the list of apps and tweaks included. It will tell you what radio version it has if it has the radio portion included...( this is for ANY cooked rom. The chefs work hard to make these and are rightly proud of their work.)
Here are the instructions for sd card flash again if you missed the first time
1). Format sd card fat32 then copy the .nbh file onto it. Rename it to "Hermimg.nbh".
2). Put it in phone and reset to bootloader - Hold down power button, ok button above flywheel and reset with stylus. Hold all buttons in until you get to tri-colour screen. It should recognize the flash image so then follow the prompts.
Its that easy when you have Hard SPL on your phone...
Cheera...
It worked very well. Thank u very much!
Sow if you don't have Hard Spl on your phone the SD flash method won't work? I have a spv m700 and coun't manage to install hard-spl.
Go to the last few pages of the Hard SPL thread - its a sticky - You'll find out how to install Hard SPL using the sd card method. Don't have to worry about sync errors with the PC then...
Cheers...
I have got Hard-SPL 2.60. Which one should I pick in the SPL Meny? I'm kinda noobish when it comes to this ...
I hope someone can help me , i ve tried a lot of roms, and i cant upgrade it, i also tried the sd flash , but it got stuck on the boot screen , could someone please help me, what should i do?
Phone is a MDA Vario 2 (Herm300), though i had ran the SIM & CID unlocker succesfully a few months ago and have been using an o2 sim since.
I thought i'd upgrade to WM6 (installed it fine over a year ago) so picked the o2 one from the list on here. The upgrade went fine, it completed and i clicked Finish when i was prompted. The device first got stuck on the Windows Mobile screen then froze up when it actually goes past on to the today screen. The o2 customisation stuff starts to install but as before it freezes after 2 minutes or so, after soft reset it bypasses that and boots to Today screen. I'm also getting the No GSM message on the o2 splash screen prior to the freezing up. When it does boot up to Today screen all functions are working for about 2 minutes then it dies.
So now it wont connect to activesync and nor will it respond to any SD card install. Bit cheesed off, had my head in the Wiki almost all day trying things out but with no joy and something that was straight forward over a year ago has turned into a nightmare and my brain now aches.
Is there any way i could get back to the default tmobile rom? All i'll do then is run the SIM & CID unlocker again and leave it at that. I only wanted WM6 for the HTML emails.
You didn't flash Hard SPL V7, did you?
You can try installing the stock rom back again but if you can't get it to run you're in for a world of time consuming reading....
You MUST Install Hard SPL V7 if you recover your Hermes as it makes it easier to recover if something like this happens...
ultramag69 said:
You didn't flash Hard SPL V7, did you?
You can try installing the stock rom back again but if you can't get it to run you're in for a world of time consuming reading....
You MUST Install Hard SPL V7 if you recover your Hermes as it makes it easier to recover if something like this happens...
Click to expand...
Click to collapse
The device was CID & SIM unlocked first. The bootloader shows IPL - 1.04 and SPL - 1.40.Olipro
How can i install v7 if activesync wont connect?
use the sd card method explained in the readme that comes with hardspl
skeeve666 said:
use the sd card method explained in the readme that comes with hardspl
Click to expand...
Click to collapse
Yeah, remembered that one. I'm doing that now as i speak, just formatted the 2gb card to FAT32. I'll be back with the results shortly
Imanaged to install the Hard SPL on my device via SD card. Fortunately now and again my device boots to today screen, but only for about 2 minutes before the whole thing freezes up and has to be reset.
So during this time i copied the SSPL-HERM.exe to the phone from my SD card, deleted it once copied and took the battery out. Then when i powered device up into Bootloader i just followed the instructions, pressing the power button then the install was complete. Took about 5 seconds.
So now my device is Hard SPL-2.10.Olipro.
Am i right in thinking that now my device is prepared to be flashed? I still get the No GSM warning at the o2 splash screen and the device still crashes after 2 minutes, thats if it got that far after it gets stuck on the Windows Mobile screen.
I'm thinking now i might be better off reverting back to the default tmobile branded WM5 that was already installed.
Try installing that 1st. It may fix things.
If it does, do the search for how to fix bad blocks as it sounds like this may be a problem too.
As you now have Hard SPL V7 installed, after you check for bad blocks, you can then use the sd card method to flash whatever rom you please. I believe its safer than using the PC simply because the only things that will interrupt the flash are flat batteries, manual reset and taking the sd card out during flash.
Good luck...
ultramag69 said:
Try installing that 1st. It may fix things.
If it does, do the search for how to fix bad blocks as it sounds like this may be a problem too.
As you now have Hard SPL V7 installed, after you check for bad blocks, you can then use the sd card method to flash whatever rom you please. I believe its safer than using the PC simply because the only things that will interrupt the flash are flat batteries, manual reset and taking the sd card out during flash.
Good luck...
Click to expand...
Click to collapse
I followed the instructions for flashing with sd card using the tmobile WM6 rom, which told me to extract the nbh file from within the rom and rename it loading it to the sd card before restarting the device to bootloader.
I did this and it said it was completed after what must've been only 5 seconds. Something must have been wrong with that. Especially as it still boots an o2 splash screen.
What am i doing wrong here? I'm sure i have followed every guide to the word so i'm a bit lost.
Once i've downloaded the rom i want, what do i put on the SD card in order to flash from it?
3 things...
1 MUST be 2Gb card or less.
2. MUST be formatted FAT32 - comes default format FAT.
3. Spelling has to be correct. Must be hermimg.nbh, no mistakes allowed.
Check these things, never failed for me as I don't use the P\C to flash since I found out how to do this...
Cheers...
3 steps.
1. Format sd card FAT32 and copy .nbh file onto it, rename to hermimg.nbh.
2. Insert card into Hermes and reset to bootloader.
3. If everything is right, follow directions.
Easy...
I've done it! Yay
**** knows where i'd be without you guys. BIG BIG thankyou to all who posted useful information for me to read in the forums.
It took a while but eventually the v3a unlocker got there. Booted the phone up and it now seems to works fine, it hasn't frozen up either.
Hi Guys
I need your help right now...
It's my first time I'm trying to flash my MDA VARIO II form WM 5 to WM 6.
I found this ROM here in the Board:
http://forum.xda-developers.com/showthread.php?t=359917&highlight=Shamanix_WM6_Ultimate_v2_FINAL
I also installed HardSPL 7 Using this guide:
http://www.mrvanx.org/thg/index.php?option=com_content&task=view&id=16&Itemid=26
And now I want to install the new ROM Using this Guide and the File above:
http://www.mrvanx.org/thg/index.php?option=com_content&task=view&id=17&Itemid=26
But when I click Autodetect it says: Error! Unknown Version.
Sorry for asking so stupid questions but i am a bit confused right now and I really don't want to crash my phone, this would be a mess....
Can Anybody Help me?
And is there Anything else to look after? I read something about CID unlock in the wiki, is this done by installing HardSPL?
ty so far
DasEtwas
First i would suggest reading the wiki pages as you may find something that could help, also it may not be detecting it as you do need to press accept or yes to run something on your hermes. although if it doesnt detect it you can see what spl you are running (press ok, power and reset button together) from there you can select what version you have on your devise it will also check whether hard-spl worked.
Hope this helps and good luck
Hard SPL is installed and I read the wiki, but I don't get behind the CID^^
The question is: Is this ROM Above comaptible to my MDA Vario? And anyway what is this CID?
Ty so far
DasEtwas
If you downloaded it from the Hermes section then yes...
As you have Hard SPL V7(?) (check if SPL is 2.10 oli), try the sd card method...
1. Format sd card FAT32. Copy .nbh file to it and rename to hermimg.nbh .
2. Insert sd card into Hermes and reset to bootloader, Scotty93 told you how.
3. Follow the prompts...
Easy...
Yes I installed Hard SPL V7 and in the bootloader it says SPL 2.10 olipro.
I will try the method now *Wish me good luck*
ty so far
DasEtwas
Edit:
Hm i don't have an Adapter for the Micro SD Card, is it possible to copy the nbh File onto the Card using Active Sync, while it's in the Phone?
Edit: Hm n1 one I tried to formate my SD Card (Yeah I found the Adapter) but windows had an Error and now it hangs up everytime I try to access the card....