i tried every thing and my Niki cant get in SPL. And solution?
This error isnt possible!
But at me every thing is possible.
This error could be becouse i have orginal Orange ROM?
The only way to get in i use customRUU and plug off cable when 3color screen appears...
tztztz
but the batterie out ... but the batterie in ... press green button and power on ... you are in spl!
if you do this without batterie reconnect ... you cant enter!!!
read the wiki carefully
Related
help me please my device is dead how can i backup it agian
if any one know help me the story is when i do a hard rest and make an upgare the imate tyoe in the screen that is erasing rom and the is shut down and now when i repack to update is give me this screen shot what i do
Try pressing "Power Button" + "Reset Button" + Directional Pad (the center) Button" then you will go to boot screen.. If you see "Serial" on top and "v1.06" below try docking the device on the cradle then reflash.. reply asap with the result..
i try this but no answer
what can i do please
alloooooooooooooooooo i want any answer plz
Here... Put this file "HimaClearJumpCode.exe " in the same directory as the ROM and installer and it should work this time...
Also, try to use the power supply connected to the cradle, sometimes the power provided through the USB cradle is not enough.
If it works, chances are you will get another error "Country Error". If that's the case, use the attached file "himaupgradeut_197.exe" instead, this will skip the country check.
Good Luck!
Rayan
my friend it dose not work what can i do please i want to repaire it and i can't do that and how does it work please insert some picture about the steps to understand that
and thank you again about your steps
Please describe what you see on the PDA screen when you power up?
Does it boots all the way into the Windows Mobile Today screen?
Do you only see the word "Serial" on a blank screen?
Please provide more details.
the details is
1- when i put the pda in the cradel it is give me the red light but this happen without put the battery in the pda the problem is when i put the battery in the pda it give me no light
2- i changed the battery but no answer
3- i try to put it in the cradel and recharge for 1 night and put it in the pda but now answer
4- i read abut reflashing but this is very hard and i can't see any replay abut that
5- now i want to tell you the summry when i put the pda with the battery and it full cahrge it give me now answer and the active syn did not find any thing and on the screen there is nothing not serial and not usb ver the screen is black
please tell me i'm in egypte and no one know to repaire it
what can i do
Sorry, but as far as I know, you will not be able to reflash if you can't boot or at least see the bootloader screen (blank screen with SERIAL text).
May I ask, what caused this problem in the first place?
What model do you have? Himalaya, Alpine, Wallaby, etc...
i have himalaya 1.2
is this write or not
where are you
do you know waht i must to do my friend
where are you
no one know
Can you tell me what will you see if in your screen if you press the "Power Button" + "reset Button" + Directional Pad Button (The center one)? cuz thats the best you ca do...
my friend when i connected the power my device is not work how?! because when i put the battery in the device it gives me that no power in the device ,then i changed the battery but the problem still appear when i put the device in the cradel the red light becomes work but this happend when i put it without battery now when i put the battery the device turn off the red light and not give me any thing now i want to give the device power
how can i do that and how can i fix the screen that tell me that the device is not in the cradel this screen is apper for me my frindes
and when i press that buttons nothig happen i don't know waht but now i want to give the device the power how can i do that do you have any answer about that
i have an ameo and it went dead. i can get it in the bootscreen or connect with usb. how can i get to the usb bootscreen. hard reset doesnt work then it says press action to restore factory default. but it doesnt do anything. i just want to get the rainbow screen with usb, just sop i can connect with sync or something else
please help me
Allready tried to put out your micro SD? And thenn do a reset?
Does your computer recognise your device when you plug it in?
What does the bootloader say your SPL is?
If the answer to the first question is yes then you should be able to flash one of the WM6 ROMS onto your device regardless of activesync. If your bootloader says you have Olipro's SPL then you can flash ANY ROM. Only found this out yesterday. If your device is a different spl then you'll have to install one which matches your CID.
Ameo Fix
Hold the Camera and Comm Manager button and press reset to load into Bootloader, then install ROM image
05mehmet said:
Hold the Camera and Comm Manager button and press reset to load into Bootloader, then install ROM image
Click to expand...
Click to collapse
make it and flashing sopp bei 1 %
ERROR(294): INVALID SELLER -ID
felix999
ATHE100
AOL-v1.00
ATHE100
SPL-v1.10.RP00
I have WM5.0
runing AthenaUnlocker
STEP1>>>all OK
STEP2>>>stop by 60 % and now can do nothing
only have bootloader and now corect rom...
please help???
felix999
I need to upgrade the SPL on my SPV C550 now that I have unlocked it (trying to install WM6)
Do I have to buy a mini SD card reader or can I use tools to do this from my PC.
If so which tools please and briefly how.
Cheers
John
john72821 said:
I need to upgrade the SPL on my SPV C550 now that I have unlocked it (trying to install WM6)
Do I have to buy a mini SD card reader or can I use tools to do this from my PC.
If so which tools please and briefly how.
Cheers
John
Click to expand...
Click to collapse
Although a search would solve your problem here is a mini how to:
- you need to have ParchedRUU (this includes these files: EnterBootLoader.exe, Patched_RUU.exe, ROMUpdateUtility.exe, RUUGetInfo.exe and finaly your_bootloader_name.nbf) all in the same directory. The files are availabe on the net just google it.
- establish an activesync connection with USB, to do so have the phone in standby mode (no bootloader mode)
- when connected in activesync (green icon on taskbar) run the Patched_RUU.exe
- make sure you tick the boxes and the next button and that phone battery is greater than 50%
- in the final screen hit the update button, if the .nbf is in the same directory as the Patched_RUU it will load it automatically
- wait for 3 minutes, during this time you phone will enter bootloader mode, and a red bar will show the progress on the phone and the computer
you are all done
- mike
Cheers mate that did the job.
Next I guess I get into boot loader mode and then use mmty.exe?
Any clues please on how to get into boot loader mode.
john72821 said:
Cheers mate that did the job.
Next I guess I get into boot loader mode and then use mmty.exe?
Any clues please on how to get into boot loader mode.
Click to expand...
Click to collapse
again search m8!
anw here it goes:
- go to active sync -> settngs -> disable USB connections
- switch off your phone, and while holding the camera button connect it to the USB, on the screen it will appear "Need UI upgrade? (0)" or something like that.. bottom line is press 0
- then phone enters bootloader mode. if on the lower bar i think it is the green bar it says hurricane and on the right UI then it is all good, if it says something like XIP or something then you have to switch it off and do the proccess from the begining with the camera button REMEMBER TO PRESS THE 0
- fire up the mtty.exe, remember put mtty.exe AND the bin in the C:\ directory. The only thing you need to change in the startup screen of mtty is the connection port change from com1 or something to usb and press ok
- press enter so the Cmd> shows on the blank terminal
- write without quotes "l c:\name_of_your_rom.bin" and hit enter. l is a small L short for load
- hopefully it will do the update, wait for ~10 mins and it will say that it is all done... depending on your rom you may have to change language and so...
hope this helped
- mike
Sorry to carry on a bit but I get this when I do what you suggested.
Cmd>l C:\wm6.bin
clean up the image temp buffer at 0x8C080000 Length 0x01C40000
MTTYDownloadImageNot allow operation!
Error : DownloadImage return error (code = 0xFFFFFFFF)
Ive Googled this and im sure ive unlocked my phone - but is that the same as unlocking the super CID?
i dont remember man, are we allowed to post links to other sites? anw follow this guy's tutorial it is allmost the same
http://karhoe.byethost33.com/content/view/35/1/
- mike
help..
need to flash phone from boot loader mode..no standby mode..how do i do that???
HELP!!!!!!!!!!!
Just follow my guide in the signature, but use huricane ROM instead, you need to get into the bootloader and enable AS USB mode, then run the RUU
i hv made a mistake while upgrading my spv c550(HTC Hurricane) to wm6.
i have flashed the wrong spl SPL 1.01.0109 on my fone. that spl was of htc typhoon.
now my phone is not booting up.
when i press the power button the fone gives the white disply and nothing else happens.
i cannot even get into bootloader.
the charging function works when the fone is turned off.
when i turn on the fone it dos nothing not even chaging.
is there any way to get my old fone back...
help plz
i shall be very thankfull to you.
DEAD SPV
i hv made a mistake while upgrading my spv c550(HTC Hurricane) to wm6.
i have flashed the wrong spl SPL 1.01.0109 on my fone. that spl was of htc typhoon.
now my phone is not booting up.
when i press the power button the fone gives the white disply and nothing else happens.
i cannot even get into bootloader.
the charging function works when the fone is turned off.
when i turn on the fone it dos nothing not even chaging.
is there any way to get my old fone back...
help plz
i shall be very thankfull to you.
Where I can find the latest SPL for C550?
PLEASE help
I've flashed my Prophet to ROM Diamond..........
Everything was fine, instalation without any problem...
But when it was done, I've made a hard reset and than it just loads bootloader and nothing alse, when I tryed to flash-back the WM5 it writes that I haven't connected PDA to PC.
PLSSSSSSSSSSSSSSSSSS
Help !
connect USB lead press and hold camera button / press reset button still holing cam button a three colour boot screen should appear now you can re flash your ROM using the normal method
thanks
thank's for reply, I've tryed this but nothing happend, but the "NVID_RUU" has solved that. ;-) THXXX
where ?
and just onw more question.. where can I down the "HARD SPL" ? I've looked around but havent foud any...
I think this tool does the spl for you
Info
http://forum.xda-developers.com/showpost.php?p=2317108&postcount=1
Download here:
http://rs636.rapidshare.com/files/209950732/Prophet_Tools_2.8.3.zip
thX
thank's now its fully working and running on wm6.1
Dear All
I have upgrade the atom with the atom rom WM6.5 21500. The rom was successfully upgraded but i don't like it. And when i tried to downgrade it to WM6.1, it didn't work. I have tried to enter bootloader but i can't, when the atom restart, they will not boot and restarting again and again. .
Please help in this matter..
thanks.
Qiky said:
Dear All
I have upgrade the atom with the atom rom WM6.5 21500. The rom was successfully upgraded but i don't like it. And when i tried to downgrade it to WM6.1, it didn't work. I have tried to enter bootloader but i can't, when the atom restart, they will not boot and restarting again and again. .
Please help in this matter..
thanks.
Click to expand...
Click to collapse
1. If your atom can goes into windows u can downgrade to 6.1 or 6.5 from my signature by using RUU from PDA viet.
2. If your atom can't goes into windows as well as boot loader, First you have to take out the battery for one or two minutes then put it back then try to enter boot loader again, if still not try the Second step by taking out the battery again then press and hold Reset + Camera button for one or two minutes then put battery back (keep pressing that button till u can see boot loader).
just want to add dolphin post
ur device is bricked, if and only if, ur device won't start normally... even if u press soft-reset, hard-reset, or even bootloader mode buttons. Before panicking, do da following:
Brick Test:
1. Make sure ur device has ample battery charge. If u're not sure plug it in with da wall charger for at least 10min
2. Remove ur battery for at least 1 minute
3. Replace ur battery while observing da LED lights
4. If da LED blinks once upon battery insertion, u might have hope yet
Da only way to upgrade on a semi-brick device, is to upgrade through bootloader mode. No bootloader mode, No upgrade possible - period.
Entering Bootloader Mode on Semi-Brick Atom:
1. Remove battery for for at least 1 minute
2. Press CAMERA+RESET(stylus) simultaneously
3. Insert battery while still holding da buttons
4. Release da buttons at da same time(u should see bootloader screen)
Note: Failure to hold the buttons at da same time during battery insertion will cause it not to work.
GOOD LUCK
dolphinxda said:
1. If your atom can goes into windows u can downgrade to 6.1 or 6.5 from my signature by using RUU from PDA viet.
2. If your atom can't goes into windows as well as boot loader, First you have to take out the battery for one or two minutes then put it back then try to enter boot loader again, if still not try the Second step by taking out the battery again then press and hold Reset + Camera button for one or two minutes then put battery back (keep pressing that button till u can see boot loader).
Click to expand...
Click to collapse
i follow all your step by step sugestion but it seems not working and i still cannot run into bootloader or switch to another O.S.
is there any other solutions you can give??
your help is very apprecciated.
knoxbrotherhood said:
ur device is bricked, if and only if, ur device won't start normally... even if u press soft-reset, hard-reset, or even bootloader mode buttons. Before panicking, do da following:
Brick Test:
1. Make sure ur device has ample battery charge. If u're not sure plug it in with da wall charger for at least 10min
2. Remove ur battery for at least 1 minute
3. Replace ur battery while observing da LED lights
4. If da LED blinks once upon battery insertion, u might have hope yet
Da only way to upgrade on a semi-brick device, is to upgrade through bootloader mode. No bootloader mode, No upgrade possible - period.
Entering Bootloader Mode on Semi-Brick Atom:
1. Remove battery for for at least 1 minute
2. Press CAMERA+RESET(stylus) simultaneously
3. Insert battery while still holding da buttons
4. Release da buttons at da same time(u should see bootloader screen)
Note: Failure to hold the buttons at da same time during battery insertion will cause it not to work.
GOOD LUCK
Click to expand...
Click to collapse
i follow all your step by step sugestion but it seems not working and i still cannot run into bootloader or switch to another O.S.
is there any other solutions you can give??
your help is very apprecciated.
dolphinxda said:
1. If your atom can goes into windows u can downgrade to 6.1 or 6.5 from my signature by using RUU from PDA viet.
2. If your atom can't goes into windows as well as boot loader, First you have to take out the battery for one or two minutes then put it back then try to enter boot loader again, if still not try the Second step by taking out the battery again then press and hold Reset + Camera button for one or two minutes then put battery back (keep pressing that button till u can see boot loader).
Click to expand...
Click to collapse
i follow all your step by step sugestion but it seems not working and i still cannot run into bootloader or switch to another O.S.
is there any other solutions you can give??
your help is very apprecciated.