PLEASE help
I've flashed my Prophet to ROM Diamond..........
Everything was fine, instalation without any problem...
But when it was done, I've made a hard reset and than it just loads bootloader and nothing alse, when I tryed to flash-back the WM5 it writes that I haven't connected PDA to PC.
PLSSSSSSSSSSSSSSSSSS
Help !
connect USB lead press and hold camera button / press reset button still holing cam button a three colour boot screen should appear now you can re flash your ROM using the normal method
thanks
thank's for reply, I've tryed this but nothing happend, but the "NVID_RUU" has solved that. ;-) THXXX
where ?
and just onw more question.. where can I down the "HARD SPL" ? I've looked around but havent foud any...
I think this tool does the spl for you
Info
http://forum.xda-developers.com/showpost.php?p=2317108&postcount=1
Download here:
http://rs636.rapidshare.com/files/209950732/Prophet_Tools_2.8.3.zip
thX
thank's now its fully working and running on wm6.1
Related
i have an ameo and it went dead. i can get it in the bootscreen or connect with usb. how can i get to the usb bootscreen. hard reset doesnt work then it says press action to restore factory default. but it doesnt do anything. i just want to get the rainbow screen with usb, just sop i can connect with sync or something else
please help me
Allready tried to put out your micro SD? And thenn do a reset?
Does your computer recognise your device when you plug it in?
What does the bootloader say your SPL is?
If the answer to the first question is yes then you should be able to flash one of the WM6 ROMS onto your device regardless of activesync. If your bootloader says you have Olipro's SPL then you can flash ANY ROM. Only found this out yesterday. If your device is a different spl then you'll have to install one which matches your CID.
Ameo Fix
Hold the Camera and Comm Manager button and press reset to load into Bootloader, then install ROM image
05mehmet said:
Hold the Camera and Comm Manager button and press reset to load into Bootloader, then install ROM image
Click to expand...
Click to collapse
make it and flashing sopp bei 1 %
ERROR(294): INVALID SELLER -ID
felix999
ATHE100
AOL-v1.00
ATHE100
SPL-v1.10.RP00
I have WM5.0
runing AthenaUnlocker
STEP1>>>all OK
STEP2>>>stop by 60 % and now can do nothing
only have bootloader and now corect rom...
please help???
felix999
Hi!
I downloaded a dumped German WM6 Rom. Now I have a big problem. I turn the device on, and the normal HTC Logo appears.
After that, the Qtek Logo appers, and that is all. After the second Logo nothing happens. What can I do?
I tried a soft reset, the same problem. (Reset Button)
I tried a hard reset, the same problem. (Camera, Comm-Manager, Reset)
I tried the same with the Camera and the Reset Button without the Comm-Manager Button. Is it possible to get a running system back? I made a Backup long time ago, so the files can be deleted.
Thank you very very much.
Enter bootloader mode, connect the usb cable and flash back to original WM5 rom.
Hi!
Damn, I used the wrong update. Thanks..
I had wm6 on it, prophet touch 4.0.0.6 and i tried now to install IX version, and after first install i made reboot and doesn't start anymore (. It's stucked in HTC Prophet Touch from beginning, and is showing in left corner ILP SPL..etc...in bootloader i can't enter (doesn't appear anymore). what should I do? It's a G4
Did you TRY to enter bootloader yourself??? I haven't quite understood your post. In case you didn't:
Press Camera + Soft Reset, then release soft reset and keep pressing camera button till bootloader appears.
yes i tried that. I've pressed camera+soft reset and holding camera..and nothing happened.
yes i tried that. I've pressed camera+soft reset and holding camera..and nothing happened.
solved. it was from my SD card. i've get it off and now is working: entering bootloader, installing ROM. thx anyway.
hey guys,, I did a foolish thing and now i'm stuck!!!
I did the HardSPL thing(apparently wrong!!)
and then i started using RUU flashig the new rom
so now from my SPL on the boot screen i get that the hardSPL didn’t function, and its stuck in boot loader with old SPL
and now that i've flashed the new rom, i cant hardSPL again,,,,
I'm so stuck,
i guess i can flash AKU 2.2 and then hardSPL again,
does it gonna work?
is there anyyyything i can do?
plzzzzzzz
IPL 2.20.0001
SPL 2.20.0001
thom_yorke said:
hey guys,, I did a foolish thing and now i'm stuck!!!
I did the HardSPL thing(apparently wrong!!)
and then i started using RUU flashig the new rom
so now from my SPL on the boot screen i get that the hardSPL didn’t function, and its stuck in boot loader with old SPL
and now that i've flashed the new rom, i cant hardSPL again,,,,
I'm so stuck,
i guess i can flash AKU 2.2 and then hardSPL again,
does it gonna work?
is there anyyyything i can do?
plzzzzzzz
IPL 2.20.0001
SPL 2.20.0001
Click to expand...
Click to collapse
try the ................................
ok, let me know about this ( i've found at WIKI )
Prophet Hard Reset Procedures
How to make a PROPER Hard Reset?
Method 1:
1. Press Camm & Comm button simultaniously. Keep them pressed.
2. Punch the little hole at the bottom with the stylus for a second or two.
3. Release the stylus (keep the buttons pressed!)
4. A white text-message appears on a black screen, telling you to press the send button
5. press the green button(the one you press to make a call).
6. Now, release the Camm & Comm buttons
7. The message on the screen tells you some more about formatting.
8. Release every button, you are done!
Done.... I had done untill number 3.
But a strange at number 4 and 5 !
I stand push Cam and Comm button while pressing green button, but nothing happen !!
Did I do wrong thing ? When I release Cam and Comm THEN I press green button, there is a massage that format FAILED !!!
plz give me a hint for this one ...
cheers,
ermen
ermenzegna said:
ok, let me know about this ( i've found at WIKI )
Prophet Hard Reset Procedures
How to make a PROPER Hard Reset?
Method 1:
1. Press Camm & Comm button simultaniously. Keep them pressed.
2. Punch the little hole at the bottom with the stylus for a second or two.
3. Release the stylus (keep the buttons pressed!)
4. A white text-message appears on a black screen, telling you to press the send button
5. press the green button(the one you press to make a call).
6. Now, release the Camm & Comm buttons
7. The message on the screen tells you some more about formatting.
8. Release every button, you are done!
Done.... I had done untill number 3.
But a strange at number 4 and 5 !
I stand push Cam and Comm button while pressing green button, but nothing happen !!
Did I do wrong thing ? When I release Cam and Comm THEN I press green button, there is a massage that format FAILED !!!
plz give me a hint for this one ...
cheers,
ermen
Click to expand...
Click to collapse
4.1 release all buttons now,
( cancel step 6.)
OK???
dioxda2 said:
4.1 release all buttons now,
( cancel step 6.)
OK???
Click to expand...
Click to collapse
YES !!! I got message FAILED !.
ermenzegna said:
YES !!! I got message FAILED !.
Click to expand...
Click to collapse
what failed??????
1. insert stylus into the little hole (or press power button if your pda turned off) then release
2. immediately press both camera + comm buttons at the same time, wait..
3. on the black screen when you see that question (are u sure u want to format bla bla.. yes or no..), release your fingers.
4. press green button used for dialing..
i understand that you reached up to the format phase, but format is failed.
the image on your pda's rom is corrupted or it coudn't be successfully flashed, so i think you must flash again.
before trying to flash wm6.1, remember to hardSPL your device..
good luck!
thom_yorke said:
hey guys,, I did a foolish thing and now i'm stuck!!!
I did the HardSPL thing(apparently wrong!!)
and then i started using RUU flashig the new rom
so now from my SPL on the boot screen i get that the hardSPL didn’t function, and its stuck in boot loader with old SPL
and now that i've flashed the new rom, i cant hardSPL again,,,,
I'm so stuck,
i guess i can flash AKU 2.2 and then hardSPL again,
does it gonna work?
is there anyyyything i can do?
plzzzzzzz
IPL 2.20.0001
SPL 2.20.0001
Click to expand...
Click to collapse
There is this thing called the "wiki" that contains the answer to your problem. It's link includes the words "stuck in bootloader". Take a look, and you should be fine!
dioxda2 said:
try the Lazy_Tool................................... http://forum.xda-developers.com/showthread.php?t=353547
Click to expand...
Click to collapse
Your lazy tool needs an active sync connection! It's use here is wholly inappropriate.
l3v5y said:
Your lazy tool needs an active sync connection! It's use here is wholly inappropriate.
Click to expand...
Click to collapse
My intention is to help. Even not helpful, not harmful at all......
Dear All:
I bricked my device unfortunately. I am trying to go to bootloader mode but it's not working. I pressed down simultaneously the botton right below the volume down botton and the opposite botton. While both bottons pressed, I powered on the device.
However unfortunatley, it's not working. Please advise the propoer bootloader sequence for HTC Startrek / imate smartflip.
Note I can not use jumpSPL simply because the device is brick and not booting
Samer.
samery said:
Dear All:
I bricked my device unfortunately. I am trying to go to bootloader mode but it's not working. I pressed down simultaneously the botton right below the volume down botton and the opposite botton. While both bottons pressed, I powered on the device.
However unfortunatley, it's not working. Please advise the propoer bootloader sequence for HTC Startrek / imate smartflip.
Note I can not use jumpSPL simply because the device is brick and not booting
Samer.
Click to expand...
Click to collapse
Don't power it on, while pressing both buttons, hold it, and connect your device to your pc. It will turn itself on in bootloader mode. After that install an official rom...
Pampooh said:
Don't power it on, while pressing both buttons, hold it, and connect your device to your pc. It will turn itself on in bootloader mode. After that install an official rom...
Click to expand...
Click to collapse
Thank you, it worked like a charm, however unfortunatley there is no luck.
Let me start by saying that I am trying to install your ROM, so I am delighted that you have personally answered me.
It went to bootloader mode, then after checking the image it returned saying Invalid Certificate.
Then I launched RomUpdateUtility from my laptop to try to install the ROM, it starts writing the ROM, then at 4%, the mobile restarts, and the upgrade utility displays Image Corrupted.
I tried to bring a different (WM6.1 SLIM found somewhere here in this forum) and copied the file to the memory, but received the same "invalid certificate" error.
May I ask you to please suggest a resolution for this problem? thanking you.
Sincerely yours.
Samer.
Hamdullilah it works.
I figured that if the rom is having a certificate error with the device then I should be able to return to the original rom.
so I went to ftp.clubimate.com and downloaded the original rom and install it, so it did successfully.
then I restarted the upgrade process only this time I did NOT do the same mistake again (not restarting after SDA Unlock) and i got my mobile running now like a sharm on Pampooh rom.
Thanks Pampooh, you are a saver.
Have a great day.
Samer.
Congratulations. Although I would suggest that you use the ROSE release since it uses less memory and is a bit faster than the NEO release. If you do decide to use the ROSE rom, try out PointUI Home2, it looks great. I have the download link in my 1.05b ROSE thread. Good day to you too.
true, but I used a WM6.1 slim version for a long time so it's time to change. The Neo interface is amazing and i dont really care about size, If needed, I could always use the external micro SD for storage.
I think NEO rom is fabulous, you should try it
ı want to load WM 6.1 V2 Pro to my smartflip. but when it is %52 the error occurred. than the phone is closed. when ı was open it the htc picture comes and the phone dosnt open . ı cant load it again because the phone dosnt connect to pc whit usb. please help me what ı must do?
which keys ı must press for bootlooder? please help me.
lanu42 said:
ı want to load WM 6.1 V2 Pro to my smartflip. but when it is %52 the error occurred. than the phone is closed. when ı was open it the htc picture comes and the phone dosnt open . ı cant load it again because the phone dosnt connect to pc whit usb. please help me what ı must do?
which keys ı must press for bootlooder? please help me.
Click to expand...
Click to collapse
volume down botton and the opposite botton. Hold it, and connect your device to your pc. It will turn itself on in bootloader mode. After that install an official rom...