hi guys... need help.... - 8525, TyTN, MDA Vario II, JasJam Software Upgradin

Hi guys,
i'm new here and new to the Hermes and window mobile....
so, i want to upgrade my wm6 to wm6.1 but I'm stuck here...
i want to try myself but i dont want to make a mistake....
i already read and do the hard-spl guide http://www.mrvanx.org/thg/index.php?option=com_content&task=view&id=16&Itemid=26 ( my spl already 2.10.olipro )
and read through the ROM Upgrade Guide http://www.mrvanx.org/thg/index.php?option=com_content&task=view&id=17&Itemid=26
wat should i do now? I'm totally confused.....
sorry and thx in advanced

I think I had similar problems when I started...
Make sure you have microsoft .net framework installed...
Linky...
Version 2.0 will do...

argentocruz said:
I think I had similar problems when I started...
Make sure you have microsoft .net framework installed...
Linky...
Version 2.0 will do...
Click to expand...
Click to collapse
already installed but it not fix the problem....

Use the sd card method.
1. Backup sd card - format FAT32. Copy .nbh file onto it (from rom you want). Rename .nbh file to hermimg.nbh . SPELLING IS IMPORTANT...
2. Insert sd card into Hermes and reset into bootloader - hold power, ok button above flywheel and reset with stylus. Hold ALL buttons in until you get to bootloader.
3. As long as you have Hard SPL V7 installed it should work, follow the prompts.
The sd card MUST be 2Gb or less, it must be formatted FAT32 (default is FAT) and you MUST have both a charged battery and Hard SPL V7 installed.
Cheers...

Related

How to flash gene via memory card?

How to flash gene via memory card?
if possible give the instructions please
it is very easy so no one answer ?
OR it is impossible so no one answer ?
sd card flashing
polifon said:
How to flash gene via memory card?
if possible give the instructions please
Click to expand...
Click to collapse
hi, you must place the rom on the sd card and then softrest while holding down the camera button. this will make the phone enter the bootloader and look for a rom on the sd card. i think that roms have to be specially cooked to be flashef in this way
zinzar said:
it is very easy so no one answer ?
OR it is impossible so no one answer ?
Click to expand...
Click to collapse
yes it is too easy with a search in this forum so no one bother to reply...i think....
Format SD-Card as FAT32.
rename RUU_Siged.nbh to GENEIMG.nbh, Put GENEIMG.nbh on SD-CARD (root).
Charge your device at 100%!
Insert SD-Card in Gene, press AND HOLD "Camera" button, and do soft-reset.
If you see white screen with "Reading SD content":
Release "Camera" button, wait, and when countdown (start from 10s) in left-bottom corner of screen is appear, press "Power" button. Flashing is begin, and approx. 8 minutes long. After you will see "Success. Press any key". Do soft-reset. Congratulation.
PS: not all the rom can be flash via SD card, if you failed, do it the normal way with USB RUU
rexypow said:
yes it is too easy with a search in this forum so no one bother to reply...i think....
Format SD-Card as FAT32.
rename RUU_Siged.nbh to GENEIMG.nbh, Put GENEIMG.nbh on SD-CARD (root).
Charge your device at 100%...........................
PS: not all the rom can be flash via SD card, if you failed, do it the normal way with USB RUU
Click to expand...
Click to collapse
One thing more
In normal way by flashing using PC i make this before
1.Olipro's SPL for Old Gene
2. i have now white screen so i can flash the rom otherwise the device will breakdown if i did not jump the spl
SO by sd card there is no need to jump spl or what , explain please
greate very usefull info thanks
@Zinzar: I have never used JumpSPL trick, right from the time i flashed my first ROM, i flashed the HardSPL and as mine is a New Gene the Olipro method bricked it and then i unbricked it using Orefkov's method. HardSPL is permanently applied and is never needed to apply again. After that you can flash your phone in both way, RUU and SD Card. NO special thing is needed to do. just format the sd card with Fat32, 4096 kb cluster size (the default one), put the RUU_Signed.nbh on sd card and rename it to GENEIMG.nbh, reboot the phone in bootloader mode and it will read the rom file from sd card. After that just follow the onscreen instructions.
I hope i have answered your query coz i dont really got your question.
active sync not working after rom upgrade from sd card
hi all,
i have recently upgrade rom ver 6.5 21501 using sd card method.
now my gene could not connet with my pc for active sync.
i want to use other rom like 19971wwe_fusion9.nbh by lomlom. i like it very much.
when i soft-reset with camera button pressed, there is a try colour screen but don't show there below "usb", when i connect my phone to pc using cable.
please provide me the solution...
thanks to all....
during update from SD card...... it says reading second OS from SD, and then says "SD FAT update failed !!!"....... also is there a deriver for the 64-bit version of the USB method???
How to flash rom on gene from the sd card
hi
pls see below details for the same
.HOW TO FLASH ROM ON GENE FROM THE SD CARD
1. Rename the .nbh file of your rom of choice to GENEIMG.nbh, drop into the root of your SD card.
2.Poweroff your phone
3.hold the volume down key and while continuing to hold it power on ur phone
4. The Phone will go into the bootloader mode, and will auto detect the rom image from the SD Card and ask if you want to proceed by hitting the power button. Hit the power button and the rom will install
Note : it should take about 10-15 mins (as of now i have not tried this try at ur own risk )
also make sure that ur SD card is Fat32 or format the same to Fat32 & use a smaller memory card the smaller the better
this is as per my experience using the above method on my previous phone ie gene(P3400i)
correct me if im wrong
thanks
hari
i exactly did that..... i'm using a 2GB micro SD with an adapter.... it detects, starts, but at the reading second OS stage it fails with the error...........
Also RUU fails for 64bit system (Using Win7 HP x64).... did it on a friends 32bit....
shantanuthatte said:
i exactly did that..... i'm using a 2GB micro SD with an adapter.... it detects, starts, but at the reading second OS stage it fails with the error...........
Also RUU fails for 64bit system (Using Win7 HP x64).... did it on a friends 32bit....
Click to expand...
Click to collapse
rename the ruu_signed.nbh to GENEIMG.nbh and the flash a custom rom via storage card.
rom upgrading works very fine on win7 64bit.you Just need to use the right drivers for the same.
karan999 said:
rename the ruu_signed.nbh to GENEIMG.nbh and the flash a custom rom via storage card.
rom upgrading works very fine on win7 64bit.you Just need to use the right drivers for the same.
Click to expand...
Click to collapse
yes i did rename the file, then formated using fat32, 4096 allocation size.... copy the renamed file, inserted in phone, reset + camera button.... then power befor 10secs........ the process saarts but as i said... fails when it tries to read second OS......... the driver specifies for win7, vista in the guide works only for 32bit systems....
shantanuthatte said:
yes i did rename the file, then formated using fat32, 4096 allocation size.... copy the renamed file, inserted in phone, reset + camera button.... then power befor 10secs........ the process saarts but as i said... fails when it tries to read second OS......... the driver specifies for win7, vista in the guide works only for 32bit systems....
Click to expand...
Click to collapse
hi
make sure u put the rom on the root of ur SD not inside any folder OK
thanks
hari
yes there is only one file.... GENEIMG.nbh, no folder, no other file..... I tried with three ROMs, two customs by others, third one my own but a stock 21911 ie without changing anything all fail at same stage.... I has earlier (long before) HardSLP'ed mine to Oref.........

Helpp Me In Jasjam

ok i am totally new in this row thingyy
i have downloaded this rom :OS 5.2.20273 (Build 20273.1.3.3 PV DVH) Diamond(Full) V19
my current rom is :1.20.305.3
radio version is : 1.47.00.10
protocol version : 32.80.7020.20H
extrom version : 1.20.305.104
no the question is is this rom ok for my jasjam if yes how to install it
and if no then which one is better ?? same how to install it help me plzzz
Yes its ok...
1St read this - http://forum.xda-developers.com/showthread.php?t=296722
then INSTALL HARD SPL V7.....(check out page 116, post 1160 to use the sd card method - I find it safer and have no sync problems unlike usin the pc). Just make sure you have more than 50% battery power if you use the sd card method.
Then you can install your new OS. just unrar/zip the file. sync your phone with active sync and double click on the RUU_Wrapper.exe file... Follow the prompts...
I prefer the sd card method, I find it safer. This is slightly different than installing Hard SPL using the sd card...
1). Format a 2GB or lower sd card fat32. Copy the RUU_signed.nbh onto it and rename to "hermimg.nbh".
2). Insert sd card in phone and go to bootloader (hold power button, OK button above flywheel and reset with stylus. Hold until you get to tri-colour screen).
3). It should recognise the Hermes flash file, just follow the prompts.
YOU NEED TO HAVE HARD SPL'ED YOUR PHONE TO DO THIS.
Happy Flashing & Welcome...

HTC HERMES200 *TYTN* ROMM UPGRADEEE!!! help

Hello everyone i'm a noob.
i'm tryin to get information about installing a clean version of windows mobile 6.
This PDA was actually traded, so i'm not really familiar when it comes to upgrading or doing a clean installation.
Basically i'm trying to install with the leastt amount of programs included so I can have free space to run my htc faster.
Can someone give me any sort of advice how to flash this phone with a new rom that takes up less space.
THANK YOU For ur time!!!
OK, 1st thing to do is Hard SPL yourr Phone. Get Hard SPL V7 from here - http://forum.xda-developers.com/showthread.php?t=296722
THIS IS A MUST.... It helps if the flash goes bad (but does void any warranty)...
2nd thing to do is go to the wm06 forum and read about the cooked OSes available. These are ALWAYS faster than the carrier roms as the carriers always load up their roms with their own 3rd party apps... If you do want to use a carrier rom but don't want all the bloat they load it with reset before the "customisation" begins after setting up the phone after flashing.
I also prefer to use the sd card method when flashing as I believe its safer than using the pc BUT you need to Hard SPL 1st. To use sd card method to Hard SPL go to post 1160 on page 116 of the above link. Sd card method for oses is slightly different so read that post carefully.
To flash os with sd card (make sure you have >50% battery) -
1). format sd card fat32 and copy the .nbh file of the rom you want to it. Rename to "hermimg.nbh".
2). Put Hermes into bootloader (tri-colour screen) - hold Power, OK button above flywheel and reset with stylus until bootloader comes up.
3). If you formated the sd car fat32 and renamed the flash file properly the Hermes will recognise it and say to hit power button to start flash - hit power button. Wait until it says flash complete then reset with stylus.
Easy as 1, 2 and 3.
Cheers...
thanks alott m8!!!!!!!!
oops another problem they say in that thread i need .NET freamework 2.0.... how do i knw if i have it already??
cuz its 24 megabytes and i cant fit it inside the device memory.
any suggestions would be appreciated...
oh shoot...i didn't format the SD Card instead i just checked if it was fat 32 and it wass
so i ran the exe file SSPL and now its stuck at the tricolour screen so i might just soft reset it

PLEase Help i can't flash Anything

dear all
no gsm,no radio,no imei
i can't flash any rom include Original rom of dopod 838pro asia
my device is dopod 838 pro
i got
HERM100
ipl 1.01
spl 1.40
but i can't flash anything
i read carefully from wiki but it doesn't give me a solution...
i always get 0% stuck and connection error message
maybe last solution Flashing via JTAG...
but i have a problem i don't understand what are JTAG for???
anybody can help me To explain or give me instruction what is JTAG??
thanks...
sorry for my english because i;m indonesian
To Install Hard SPL V7.
Untick "Allow all usb connections" in Activesync on pc.
Go to bootloader on Hermes. Connect Hermes to pc.
Download Hard SPL V7 from here -http://forum.xda-developers.com/showthread.php?t=296722
Run RUU_Wrapper.exe of Hard SPL V7.
To try to recover the Radio ROM.
Find SHIPPED Stock ROM. Download.
Use sd card method to flash to Hermes.
SD Card Method.
1. Format 2Gb or less sd card FAT32.
2. Copy .nbh file to it & rename to hermimg.nbh.
3. Insert sd card into Hermes, reset to bootloader and follow instructions.
Flashing stock rom may take up to 30 minutes. DON'T INTERRUPT THE FLASH.....
Cheers...
ultramag69 said:
To Install Hard SPL V7.
Untick "Allow all usb connections" in Activesync on pc.
Go to bootloader on Hermes. Connect Hermes to pc.
Download Hard SPL V7 from here -http://forum.xda-developers.com/showthread.php?t=296722
Run RUU_Wrapper.exe of Hard SPL V7.
To try to recover the Radio ROM.
Find SHIPPED Stock ROM. Download.
Use sd card method to flash to Hermes.
SD Card Method.
1. Format 2Gb or less sd card FAT32.
2. Copy .nbh file to it & rename to hermimg.nbh.
3. Insert sd card into Hermes, reset to bootloader and follow instructions.
Flashing stock rom may take up to 30 minutes. DON'T INTERRUPT THE FLASH.....
Cheers...
Click to expand...
Click to collapse
Thanks a lot
i was try flashing from sd but what i got?
progress bar still no working??
it this Normal??
or something wrong with my device???
i try flash via activesync and bootloader "HER_DopodAsia_AUS_1.30.707.4_1.20.31.10_WWE_Ship"
with modified RUU but it still 1% progress bar show
what wrong with my device??
i really hope u can fix and help me to unbrick my devices...
ultramag69 said:
To Install Hard SPL V7.
Untick "Allow all usb connections" in Activesync on pc.
Go to bootloader on Hermes. Connect Hermes to pc.
Download Hard SPL V7 from here -http://forum.xda-developers.com/showthread.php?t=296722
Run RUU_Wrapper.exe of Hard SPL V7.
To try to recover the Radio ROM.
Find SHIPPED Stock ROM. Download.
Use sd card method to flash to Hermes.
SD Card Method.
1. Format 2Gb or less sd card FAT32.
2. Copy .nbh file to it & rename to hermimg.nbh.
3. Insert sd card into Hermes, reset to bootloader and follow instructions.
Flashing stock rom may take up to 30 minutes. DON'T INTERRUPT THE FLASH.....
Cheers...
Click to expand...
Click to collapse
thanks
i've follow that instruction flash via SD but on my hermes screen progress bar still stuck...it is normal??all ok but at radio and os still nothing...
i try to put HER_DopodAsia_AUS_1.30.707.4_1.20.31.10_WWE_Ship at formatted Fat32 sd card and i renamed it .nbh to herming.nbh
please help me for a solution
thanks

Procedure (Sorry, I just don't want a brick)

Okay, so today I purchased a Hermes. While it'll take a while for it to arrive, I want to be prepared. And I certainly don't want a brick. So I'm pretty paranoid. That's why I'm asking, is the following procedure correct? (It's basically what I found here)
Download HardSPL
Download the ROM
If I have HardSPL (which I doubt), skip step 4
Install HardSPL
Sync and connect (with USB-cable) using WMDC*
When sync is finished, run RUUWrapper.exe
Follow the instructions (accept, next, accept, next, update)
Flash
Sync and connect (with USB-cable) using WMDC*
When sync is finished, run RUUWrapper.exe, the one shipped with the ROM
Click AutoDetect
Follow the instructions (accept, next, accept, next, update)
"Enjoy my updated device"
Download and install the .cab-files provided by Torben here. (Or should I change the registry?)
*I've read that there are some problems when syncing with Vista (which I, against my will, is stuck with), is this still present when using WMDC instead of ActiveSync?
Thank you for taking time helping a confused noob!
Mate, if you have a problem with using the PC, use the SD card method (must have Hard SPL V& installed - SPL - 2.10oli). To install Hard SPL using the Sd card method, go to page 116, post 1160 on the Hard SPL thread. It has links and the method to install hard SPL using the sd card method.
For ROM's use this method -
1. Format sd card (2Gb or less) FAT32.
2. Copy .nbh file of the rom you want onto sd card and rename to hermimg.nbh .Insert back into Hermes.
3 Put Hermes into bootloader - hold power, OK button above flywheel and reset with stylus, hold ALL buttons in until you get to tri-colour screen. If you have done everything right, follow the prompts.
Cheers...
But then I would have to buy an extra memorycard for the outragous prices of $7. But, I suppose I'll have to... Thanks for your reply!
Horrors......
Okay, I read the post. Very good! Just to make sure, I should not copy the RUUWrapper bundled with HardSPL? I add SSPL_HERM.exe and HERMIMG.nbh to the root of the newly formatted (FAT32) SD-card (not SDHC), run SPPL_HERM.exe from the phone, press the powerbutton when instructed to (to flash) and then reset the device somehow, once it's done. After that, follow the instructions here (phone connected to charger since it takes 30 min) and then all be fine?
(Yepp, I'm a pretty paranoid creature)
I just thought I'd reply to this message because I'm about to flash a custom Rom to a new iMate Jasjam and that my user id is errily similar to yours
I've used a 2GB Micro SD card to flash my last ROM upgrade (thanks to CRCinAU) and it worked a treat.
Cheers!
Oggy.
On my device (MDA Vario II) it stops at the bootloader screen (tricolor), and nothing happens.... but my device is not bricked, if i call softreset everything works, but i need hard spl to use an unlocker .... (which is also not working right now)
Did you run sspl.exe from the phone first?
You need to run this as it puts Soft SPL on so you can flash Hard SPL BUT you need to run it from the Hermes and not the sd card.
To get out of bootloader just reset with stylus.]
Also check that the sd card (2Gb or less) is formatted FAT32, comes formatted FAT by default.
Make sure you have renamed .nbh file to hermimg.nbh. Spelling matters...
Cheers...
jep done as instructed, still the same problem
What happens if it's not formatted FAT by default? If I can format a card as FAT32 but wasn't FAT originally, would it possibly brick it? (Not doing it (hopefully), just curious)
okay got it, cards broken, i think, used a new one
Doesn't matter if it was originally FAT32, most sd cards come formatted FAT by default, it has to be FAT32 or the flash WON"T work...

Categories

Resources