My xp doesent recognize usb connection in bootloader, (but Activesync works.. so no cable problems ) 1.16.JUMP och 1.16.0000 have same issue.. (my other htc works in bootloder)
This means I cant upgrade any roms with RUU.. can I upgrade rom by SD card ?
or any other sugestions ?
regards Magnus
You can update through SD card, just use the search button on the forum. Anyway... tried to unplug and replug the usb from the phone after entering bootloader? tried entering the bootloader and then connecting the phone to the pc?
Thank you for your reply!
I have tried every sugestion you menentioned and even more without any luck. also on diffrent xp..
When I tried to upgrade from SD I followed this:
SD 2 gb formated in Nike
renamed nbh file to "NIKEIMG.nbh" File is 110 mb
copied "NIKEIMG.nbh" to root on SD through a cardreader
pressed camera power and soft-reset hardware buttons
at bootloader screen says "loading...."
It hangs here!!
Should I use any special som image or ?
some threads says its possible to upgrade with SD some not..
downloaded the service manual and followed SD upgrade procedure.
I formated SD i PC this time, and bootloader was able to read image.
(http://mikechannon.net/PDF Manuals/HTC Niki Service Manual.pdf)
upgraded (fullimage) with SD to bootloader 1.22 but still Unkown USB device in BootLoader mode.
Related
i tried to install the latest At&t ROM and i got an error asked me to try and recover it but when i try to recover it it still give me an error message and now my phone is stuck on the bootloader screen it says IPL-1.00 SPL-1.40.Olipro can someone please help me get this out of bootloader mode...i tried reseting it or tried other ROM's but nothing will work....TIA
i can't even get my pc to recongnize that my 8525 is connected to the USB port....
EDIT: I got my PC to see my 8525 by unchecking the USB connections in ActiveSync....
I think this is a crosspost from the HardSPL receovery thread, so I will just answer it here.
Manually put phone in bootloader mode.
Plug into USB
Run RUU to start ROM install
Manaually select your SPL version
Ignore warning in red letters on next screen
Flash away.
(Do not mix up the first two steps - put in bootloader, THEN plug into USB)
If this does not not work, use SD Card flashing method.
I'm sorry for the typical question and thread!I did everything but without result,
for this reason i've decided to make a post
so as i said on title i'm stuck on boot screen,to let you understand
the screen with 4 colors,red,green,blue,white.Now here the point,it seems that i can't resume my phone
from that screen!I've tried as is written here "format a microSD card with FAT32
extract the .NBH file from the rom image you like
rename the .NBH to HERMIMG.NBH and copy it to your microSD card
put microSD card in phone and start it in bootloader (hold Ok button on left side and POWER button at same time and stick with stylus in RESET on bottom)
confirm flashing on screen" but it was useless,nothing happend,when i push the left button ok
and at the same time power and soft reset,the screen change color become gray and appear a write "Loading...."and some numbers above 00068002
to return invain at the beginning screen.I don't know what i wrong and if is there another way to resume it,obviously my activesync don't work.
Here others informations if it can be useful for someone about my boot screen
Red stripe there's written: HERM200 I PL-1.01
HERM200 SPL-1.11
White stripe: Serial
does anyone had my same problem???
Please help me i really need my phone because my work
Thanks a lot
Try flashing from the computer - just start with the phone in Bootloader mode, select force using SSPL and flash whatever ROM you like. Give it a try.
Thanks for the answer!But i've already tried that way without success,maybe bcause there's not connection with the activesync,could be possible?In fact when i try appear an error wich says
ERROR [260] : UPDATE ERROR
THE UPDATE Utility cannot connect to your PDA Phone.Please check that your USB cradle/cable is connected properly between the PC and your PDA Phone.
Check the following:
1.The PDA Phone is connected to the USB cradle/cable.
2.The USB cradle/cable is connected to the PC.
Now how can i fix this problem????
Thanks for ur collaboration!!!
Pleaaaaaaaaaaase HEEEEEEEEEEEEELLLLLLLLLLLLLLLLPPPPPPPPPPPPPPPPPPP
I have exactly the same problem !!!
Damn!We gotta find a solution!Hey if you can fix our problem please let me know!And naturally the same for me.Let's keep in touch!
White stripe: Serial
Click to expand...
Click to collapse
This should switch to USB once you plug it in...
Give us a little more info now please:
* what file are you trying to flash
* what RUU are you using
* have you tried connecting with mtty (if you get in, try task 28)
* have you trried hard reset
Just to be clear on my previous post...
1. Put phone in BL mode
2. NOW plug phone into computer (that order is important)
*Phone should now say USB*
3. Launch CustomRUU (should not be a retail RUU)
4. Flash
Dear todd_jg,
first of all thanks to be interesting about my problem,
second yes my phone switch to serial in usb mode,
-regarding the RUU i don't have any idea about it!
-Can u post the right RUU that i should use please?
-Never tryed mtty
-Yes i've tried with hard reset but without result,it send me back to the boot screen
-I did exactly as you said but it was invain!
Use the RUU file from THIS THREAD
Get the nbh file
Drop it into a folder with the RUU
Launch the RUU
Whichever nbh is ok???
tetsuokaneda said:
Whichever nbh is ok???
Click to expand...
Click to collapse
Yes, but if you continue to have problems, you may wish to try a different one or at least post a link where you found it...
I got it!I'm trying right now!I'll let u know immediately!Thanx
Fu.. nothing to do....
here what it said
ERROR [260] : UPDATE ERROR
THE UPDATE Utility cannot connect to your PDA Phone.Please check that your USB cradle/cable is connected properly between the PC and your PDA Phone.
I think that the problem is the connection between the Cpu and the Pda.
tetsuokaneda said:
Fu.. nothing to do....
here what it said
ERROR [260] : UPDATE ERROR
THE UPDATE Utility cannot connect to your PDA Phone.Please check that your USB cradle/cable is connected properly between the PC and your PDA Phone.
I think that the problem is the connection between the Cpu and the Pda.
Click to expand...
Click to collapse
Alright - lets try a task 28 with mtty
You will need to find mtty first (should be a link in the wiki or use search).
The tricky part is getting mtty to see the USB connection... I get it by doing the following
1. With the phone in BL mode and mtty closed, plug it in to the USB
2. Using ActiveSync, manuallyt tell it to check for connected devices (this will get it to start polling the ports)
3. While ActiveSync is still polling the ports, open mtty
4. Where it says connect using... or port... or something like that, you should find USB001 or something like that - something with USB in the name. If you don't see it - try steps 1-3 a few times.
Once you have seen the port, you can connect to the phone. The wiki has some instructions for getting to the USB prompt in mtty. Once you are there you want to issue the task 28. See if that helps.
Here is the link to the wiki - a link to mtty is there and some directions. Good luck.
Ok here what i obtained with mtty
Cmd>task 28
Storage format start
Write Nand Success
dwBlockToWrite = 14
Can't find OS in flash!!!
Storage format success
and now?
tetsuokaneda said:
Ok here what i obtained with mtty
Cmd>task 28
Storage format start
Write Nand Success
dwBlockToWrite = 14
Can't find OS in flash!!!
Storage format success
and now?
Click to expand...
Click to collapse
Well... let's see...
SD Card - No
PC - different BLs and RUUs - No
mtty - No
Manual BL mode - No
Almost stumped here... last resort: KITL + PLatform Builder
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
OR...
Flash an OS.nb file with mtty (READ THESE DIRECTIONS CAREFULLY)
Daaaamn i think will be a long night
I hope if is gonna work
Thanks todd_jg
i'll keep u posted
first i was trying to upgrade system from O2
something goes wrong and ERROR showed
and i could only my xda in bootloader on
then i was trying to upgrade rom bootloader by mitty
i`ve done this steps :
you will lose all data on your device, and your sd-card, so make a backup first*
make sure there is no sd-card in your device.
boot your device into bootloader mode
by holding down the big action/navigator button together with the power button, and hard-resetting with the pen at the same time
now the display should say 'serial' and the bootloader version.
insert a blank sd-card
put your device in it's cradle
start mtty.exe
select 'usb' as the port in the mtty program.
type the followint command into the mtty window
d2s 60000000 00300000
this will write your radio rom to the sd-card
the last step takes very long and my pc hang up
so i treied to do the same once again but mtty showed me "usb port could not open"
and i dont know what to do know???
plz help me
sory my english isn`t good enough
regards
have you tried just putting the pda in the cradle without using mtty?
if it change status to usb serial you can run the flashtool again
Rudegar said:
have you tried just putting the pda in the cradle without using mtty?
if it change status to usb serial you can run the flashtool again
Click to expand...
Click to collapse
i have same problem...
Yes my xda-II change status from SERIAL to USB.
but in PC my xda-II detected as UNKNOWN DEVICE,
so i can't run FLASHTOOL.
i just hope if flashing to be run from sd-card
mine did that once so i rebooted and or changed usb port
Rudegar said:
mine did that once so i rebooted and or changed usb port
Click to expand...
Click to collapse
I did it, and tried to about 3 PC's winXP SP2,
and still detected as Unknown Device, i think its connector problem or hardware error
Hi! I tryed te fash my niki 200 with original rom! The flash is stopes to 42% and now i have boot mode with this message "Upgrade ROM code error! Please try again". I can not conect again to usb because i received message :"usb device not recognized". Mtty can not conect because i received the same message! There is another metod de make this device?
Have you flashed HardSPL?
Put your device into bootloader (hold b oth Camera and Power button while performing a Softreset via Stylus) and now you can theoretically flash your Provider ROM!
After that your device will work again!
I have not flashed hardspl! If i put the Niki in boot mode, show only "serial" on the screen with usb cable pluged and PC says "usb device not recocnized"!
Flashing in bootloader mode doesn't requires an ActiveSync connection so ignore it and start the ROM Upgrade! It's working, believe me! I've flashed my Niki with this method hundred of times!
I tryed to flash my niki in bootmood, but not working "error 260:conection"! My computer not recocnized my device (with or without activesync)!!!In bootmode on screen show "serial" and when i pluged the cable nothing happend (must see on screen:USB)! This is my problem!!! The computer does not alocate to my device a com port(USB). The same problem with MTTY (no USB poet detected). You understand me?
Maybe your USB drivers screwed up.
Trie with an other PC, this helped me one time.
I tryed on other computer with Xp and other with Vista! The same problem! Not recocnized!!!!!!!!!!!!!!!!!
bugytech said:
I tryed on other computer with Xp and other with Vista! The same problem! Not recocnized!!!!!!!!!!!!!!!!!
Click to expand...
Click to collapse
I've got the same issue. Did you resolve this? I would like to find a solution
I reboot holding the volume key down and it gets to the multi colored screen but there are no options on it. I'm trying to load a stock rom off the SD card. I also tried loading it through USB but it just hangs at 0% until I get error 262 update error. I have searched for answers but didn't find anything.
tmobile comes with 16gb card as stock, and there are loads of reports of 16gb cards not working for flashing. try a 2gb card for best results.
did you rename your rom to leoimg.nbh?
DN41
oh as for error 262, is that usb timeout? if so, boot into bootloader, connect usb, and then run customruu as administrator