hi everybody
i have imate jamin g4
i tried to upgrade it
but it wait in three clolor screen
not open not upgrade
always resetting
when put usb or charging wait 1-2 min and start to reset (off-on)
i tried temp rom and tried lazy tools hard spl
but not change always reset
maybe died
when it start to upgrade it start to download but it not end bcs reset, reset,reset
pls help me can i recover it
in three color screen
IPL 2.13.0001
SPL 2.13.0001
right up corner RUU
flash first WM5 rom and don`t cry.
i try to flash but when i put usb cable
it start to upload
after %20 or %5 or %42 it reset and off then on
Is your batty over 50 % ?
i dont know bcs i not see anything
i put to charger but it continue to restart
Charge your batty, with the orig. charger - After 1 hour, give it a try, and go to the bootloader modus, than take your USB to the PC and flash a WM5 Rom. Read here some treads, this is not a new prob.
ok be try with orginal charger
and write here to you
hi there
i search original charger but not found it
i make it from nokia charger and try to charge
jamin not restarted )))))
it now at charge after charge be try flash it
if it run i write you
thanks for you
i am ver happy thanks you NEO130 my jamin is run
but network signal is very low can i adjust it
Maybe take another radio Rom. Search for it, in the treads. I don`t know where.
tnural said:
i am ver happy thanks you NEO130 my jamin is run
but network signal is very low can i adjust it
Click to expand...
Click to collapse
Hey mate,
Whats the version of your radio rom?
I like 02.19.21, i think its the best radio-rom for prophet i ever used.
but that can be because i have Vodafone, dont know if its also the same with your provider...
but i should say, give it an try!
here you can download all Radio-Roms.
First of all, when u start flashing (doesn't matter what rom) always use HARD-SPL!
And i can advice you an good rom(although for me in case)
The rom made by VaranusVincent
ROM Prophet Blue Manilla 2d
Have fun!!
Good help&work NEO130
dead iamte jama
can any one please help me as welll....
i was try to update my rom from dnw.exe....
i was trying to upgrade my rom to wm7
when i was upgarding bootlaod.nbo my jama hang
when i remove the battery and install it again since then it wont start
no screen not even charging light is blinking its totaly dead
can any one please help me
before upgarding i was perfectly using WM.6.5
please brother help me out from this
...Why don't try a 'basic' wm6.1 rom and try to upgrade step by step?
Try some Bikertibi rom.
bilalpai said:
can any one please help me as welll....
i was try to update my rom from dnw.exe....
i was trying to upgrade my rom to wm7
when i was upgarding bootlaod.nbo my jama hang
when i remove the battery and install it again since then it wont start
no screen not even charging light is blinking its totaly dead
can any one please help me
before upgarding i was perfectly using WM.6.5
please brother help me out from this
Click to expand...
Click to collapse
There is no WM7 for the prophet and u used a next upgrade tool not recommended really did you not know that WM7 have not came out as yet? am sorry I cant not help you u will have ether buy a next device or go back on the forum you got the files from tell them what happened and ask them for a solution but you should of stayed on windows mobile 6.5
Related
dear all friends
i have wiza200 k-jam it was work with love rom then i try to flash e it with shelltoll with RUU_Prodigy_2210206_22102109_021911_TMO_UK_WWE_Ship
and then phone hange in phone screen ibl and sple it can go to boot mode
but how can reflash it. it cant accepte update so please help me how can i revive it please tell me .
iam waiting help .
put the device in bootloader mode and flash the latest rom from your carrier quick!!!! before the battery drains out.
holding down the camera button then press the soft reset whole..
that should bring you to bootloader.. then flash!
Faria
Greetings,
Faria if in this case the battery drains totally the phone wont revive?
Thanks.
samy.3660 said:
Greetings,
Faria if in this case the battery drains totally the phone wont revive?
Thanks.
Click to expand...
Click to collapse
Yes if the battery drains and the phone has no OS it is not capable of recharging the battery as this is controlled by software not hardware, an external charger would be needed to charge the battery and then flash the phone.
i charge battry with power suplly nd phone goes into flash mode but whats tool can i flash it with the update not work i have usb cable without charger .iam waiting steps to riveve it please give me link for any tool and flash files and steps .
and very thanks for all replay
waleed2 said:
i charge battry with power suplly nd phone goes into flash mode but whats tool can i flash it with the update not work i have usb cable without charger .iam waiting steps to riveve it please give me link for any tool and flash files and steps .
and very thanks for all replay
Click to expand...
Click to collapse
the tool you need to current revive your device is the latest official rom from your provider.....t-mobile- orange ?
link for wizard love rom
here is a link for the wizard love rom you will be able to flash your device using it get most people out of trouble the once charged can use the shell tool again
http://rapidshare.com/users/EXGZ7T you will find it a the bottom of the page
i have the love rom but i cant flash it i see this errore
so what can i do iam waiting it was love rom isdie it it before hange with shelltool
thanks to all the wizard now back to live but i have same problem it has simlock ans isee in the screen you have tried 9times please retry
so how can i slove this probem
My Wizard
I tryed to change the rom of my wizard do WM6. Now i can see the Bootscreen with T-Mobile but then nothing more comes. So i tryed to role back an older Rom vor my MDA. But i get the same error-message like the guy before.
So what can i do?
worker2000 said:
I tryed to change the rom of my wizard do WM6. Now i can see the Bootscreen with T-Mobile but then nothing more comes. So i tryed to role back an older Rom vor my MDA. But i get the same error-message like the guy before.
So what can i do?
Click to expand...
Click to collapse
I got it. Its working again. But I want Windows Mobile 6. So if someone can give me a clou how to change the rom and where I can find a ROM for G4 that would be great.
THX
I tried using the shelltool to flash the faria rom and after the hard reset which was instructed, my phone hangs at the startup screen with:
IPL 2.22.0001
SPL 2.22.0001
GSM 02.25.11
OS 2.18.0.0
My G4 is CID-locked
When i connect it to the charger, the light doesnt light up
Please help
Can you still put your device to bootloader (Tri-color screen)..??
if so then you're lucky..
I in bootloader, (Tri-color screen) and how reflash my WIZARD?
go to bootloader (Tru-color screen)
just plug you device into USB.. if you've seen the "USB" word in your device..
reflash.. just run the ruu....exe..
Who ROM choice?
Test ROM RUU_Molski[1].Biz_AKU2.3-226102_22610105_024711_WWE-30MB-CF2-G4 but my G4 still Stuck at startup
Flash with the Love Rom, it worked for me when this happened!
post your feedback after so that others having this problem will also know what to do..
--004
My device at this moment is also hanging in that cloudy startup-screen. Tanks to this topic I came to Bootloader. I had a original ROM of Qtek on my PC en now its installing...
I see the same thing when I did a ROM update last week. I see a statusbar at PC and device, they are growing. Pfiew Still my fingers crossed! Now at 95%! You will hear of me!
Device is back! Now I'll (still) try installing the ROM that I want!
Black-Rose said:
My device at this moment is also hanging in that cloudy startup-screen. Tanks to this topic I came to Bootloader. I had a original ROM of Qtek on my PC en now its installing...
I see the same thing when I did a ROM update last week. I see a statusbar at PC and device, they are growing. Pfiew Still my fingers crossed! Now at 95%! You will hear of me!
Device is back! Now I'll (still) try installing the ROM that I want!
Click to expand...
Click to collapse
yo can i have the link too where u got the orginal qtek rom i just want to make sure i got the right one
mrchezzy said:
yo can i have the link too where u got the orginal qtek rom i just want to make sure i got the right one
Click to expand...
Click to collapse
HI! I have the same problem with my Qtek9100, where can I donwload the original qtek rom?
same **** happened to me anyone kno where i could get the Love Rom from? would the button rom also? I tried the OEM rom I got an error message
You can find Wizard Love on ThePirateBay.
ANTC said:
same **** happened to me anyone kno where i could get the Love Rom from? would the button rom also? I tried the OEM rom I got an error message
Click to expand...
Click to collapse
Check here:
http://rapidshare.com/users/XP0AY2
I tried to upgrade ny Orange SPV M 600
IPL 2.10.0001
SPL 2.10.0001
with wm6_smart1_v1.3 using ROMUpdateUtility_Wizard_NoID.zip and now its not booting up it stuck up with the three color boot loader screen and i tried hard to hard reset but even after keep pressing the camera and communication button together and pressing the soft reset button with stylus for more than one minute it gave no response plz help its my friends phone and I am doomed if I cant make it up working.
If you disable the connect through USB option in ActiveSync, and then put the SPV in bootloader. Then flash it with a AKU2.2 ROM (Any will do including PV temp), then follow this: http://forum.xda-developers.com/showthread.php?t=310452.
How do i put SPV in boot loader????
AKU2.2 ROM where do i find this the link(rapidshare) which is given in thread u told is not working and plz tell me if I will have to download a new rom after that or this wm 6.0 by smart1 will work
Hold the Camera button, and insert the stylus into the larger of two holes on the edge of the SPV with the power connector.
http://wiki.xda-developers.com/index.php?pagename=Prophet_Hardreset_bootloader
ya i tried this by reading the thread u mentioned but it puts me back on the same three color screen however I have been able to hard reset and after I press send it said formating FAT something like this
You must enter the bootloader (three colour screen), Then set ActiveSync to not connect through USB (ActiveSync->Settings->connection Settings), Plug the phone into your computer through USB, Then run any of the RUU's from any Part One of here: http://forum.xda-developers.com/showthread.php?t=308755.
Using the AKU2.2 ROM Update Utility, you should get a basic WM5 ROM. You MUST flash an AKU2.2 ROM before you flash a WM6 (AKU3.5) ROM.
Right now i am downloading this original roam from this link
ftp://ftp.xda-developers.com/Uploads/Prophet/Prophet-roms/Original-Shipped-ROMs/OrangeUK/
will this do????
Can I directly install AKU 2.20 after downloading or will I have to do anything more like putting some file in boot loader which u just said???
I dont want WM 6 anymore plz just advice in steps what I should do to get my phone up and running..............
Put the phone in bootloader, change the active sync settings, and then run the upgrade program!
Good Luck!
ok i am trying let see what happens hoping for the best................
though I am scared!!!!!!!!!!
absharaslam said:
ok i am trying let see what happens hoping for the best................
though I am scared!!!!!!!!!!
Click to expand...
Click to collapse
It will do no harm, and there is a high chance it will work.
The RUU is fairly self explanatory-Double click on it and do what it says. The battery charge level is not a problem, so long as there is some charge.
Thanks a lot dude it worked I am relieved now
Thanks again boss
Salute!!!!!!!!!!!!!!!!!!
Glad to hear it
If you now feel experienced enough to upgrade properly, read this thread very carefully http://forum.xda-developers.com/showthread.php?t=310452 (or at least the first post) and then this post: http://forum.xda-developers.com/showthread.php?t=308755
atleast for now i dont have courage.............
This phone belongs to my bro and currently he is out on vacation and when he will come back i thought it will be a surprise that his phone become so good anyways no risk anymore..........
may be next time on my phone only
Well atleast he shouldn't notice the change.
Finally I have been able to upgrade to WM 6.0 using PDAViet Rom 4.0.0.0.5 and its working like charm. I checked everything including IR Bluetooth WIFI all are working fine no problem at all.
Battery consumption rate is a bit high but not alarmingly high.
Thanks Boss without your advice it would not have been possible at all
absharaslam said:
Finally I have been able to upgrade to WM 6.0 using PDAViet Rom 4.0.0.0.5 and its working like charm. I checked everything including IR Bluetooth WIFI all are working fine no problem at all.
Battery consumption rate is a bit high but not alarmingly high.
Thanks Boss without your advice it would not have been possible at all
Click to expand...
Click to collapse
No problem. Glad to make a difference
Hi Guyz
I'm trying to upgrade my friends O2 ATOM to any new software .
the problem is that when it reaches RADIO UPDATE
it stays on 0%
PDA Screen says ( UPDATE RADIO STACK ,,,, PLEASE WAIT ... )
IF I REMOVE THE USB CONNECTION , THE ATOM STICKS ON WINDOWS SCREEN , AND SOMETIMES ON SCREEN ALIGNMENT .
i tried three different roms ad got the same result , even thru BOOTLOADER screen, it is very imbarresing , as i promised him a better performance device , now it is not booting .
hhhheeeellllppppp
pleaseeee
he is looking at me and only flames are showing from his eyes
just keep flashing the device, it fails sometimes on the first flash at the radio section, simply disconnect it and then reflash it for the 2nd time.
How long you've wait the process?
I've upgrade my atom more then 10 times and when in Radio Updates it's also not showing the progress as what you've seen.
But it doesn't mean the process is stopping. Just wait and the process will finished. (Usually in it shows the progress in your PDA screen)
Don't unplug your usb cable before it finished.
unfortunatly i had to unplug the ATOM
now it gives only one massege
UPDATE UTILITY
did i brick it ?
for me, I'd take out battery a while and then connect USB and try to flash with wm5 rom like "Xda-Atom-ENG-20060105" (you can found on this forum under "Collection of All O2 XDA ATOM ROM AKU *** (WM5(2*->3*) & WM6 (0.3*->0.7*))" post).
And then upgrade to wm6 rom by ... jiggs, homer285 & udayrulz .....
hi konanda
will this resolve the problem?
yeah, I have done alot of time to solve this problem on other xda atom also .... if you want, I'l upload this wm5 rom on mediafire ....
thanx
i tried this way 2 , but again it sticks on 0% , with a massege saying , UPDATE DADIO STACK PLEASE WAIT ...
any suggestions?
shall i go to SD card way ?
Just keep flashing the device.. take a bit longer time and then will complete the updating ....
abuawab said:
thanx
i tried this way 2 , but again it sticks on 0% , with a massege saying , UPDATE DADIO STACK PLEASE WAIT ...
any suggestions?
shall i go to SD card way ?
Click to expand...
Click to collapse
Allow the projected 30 mins for the update, if you plan to update via SD Card be sure to read, ALOT! good luck, oh you could have a little read in the Atom Wiki too.
could be your cable or connection?
ATOM ROM update problem
I had the same problem & tried different ways explained in this thread.
No success.
I tried with old original ROM and all new ROMs as well, it stucked on updating RADIO BURN message on computer and ATOM displays Updating RADIO STACK.
I tried removing battery and kept for some times and tried back but same result. Please anyone can help me
i had this problem also. i was unable to reflash my atom. It stuck at the same screen as what the previous user described. At first, the touch screen failed and there isnt any GSM, as in under wireless manager, "phone" isnt there.. E.g There should be Wifi, Phone and Bluetooth in wireless manager.. But sometimes after some soft reset with the taking out of battery, the gsm comes back together with the touchscreen. But this occurred quite frequently until i decided to re-flash it.
Im using the official rom of Xda-Atom-ENG-20060426-MOT0822.. Is there any way to solve this problem?
Thanks in advance.
max20041988 said:
i had this problem also. i was unable to reflash my atom. It stuck at the same screen as what the previous user described. At first, the touch screen failed and there isnt any GSM, as in under wireless manager, "phone" isnt there.. E.g There should be Wifi, Phone and Bluetooth in wireless manager.. But sometimes after some soft reset with the taking out of battery, the gsm comes back together with the touchscreen. But this occurred quite frequently until i decided to re-flash it.
Im using the official rom of Xda-Atom-ENG-20060426-MOT0822.. Is there any way to solve this problem?
Thanks in advance.
Click to expand...
Click to collapse
try to update to any WM6 or if you still want the WM5, there are a lot of ROM
's available. I had this tradgic experience aswell with o2 default ROM. Im contented with the WM6 although no a2dp support yet =)
abuawab said:
thanx
i tried this way 2 , but again it sticks on 0% , with a massege saying , UPDATE DADIO STACK PLEASE WAIT ...
any suggestions?
shall i go to SD card way ?
Click to expand...
Click to collapse
i'll agree with the others, better change USB cable as well =) It could be faulty you can use cable from canon digicam/motorola phones et. al.
I would suggest reflashing the ROM with cooked ROM's available here like WM6 or WM5 if you still want to stick with it. o2 default ROM gives me a headache before. No1 rule before upgrading ROM...... Read the WIKI hehehehe
Hey guys I had the same problem, I went through the procedure as here http://forum.xda-developers.com/showthread.php?t=358442
Hope u can also flash 'OS+EBoot' part of it and then after ur Atom Exec restarts u can go in bootloader and flash the original WM5 from O2 ‘Xda-AtomExec-ENG-20060614_R060428N_EX0028.exe’.
i tray to insltal new wm 6 and whail instaling error apire and naw phone dont whana start and dont whana conect whim my pc plss some1 helm me if can
i tray whit any reset dont worck eather
Plz give us more information about the problem then we can help what do you see on the screen when you try to turn on the phone? when u tryed upgrading your PDA the first time was the charge more then 50% if less it will give a error message.
Read the Upgrade Guide again and look for the Recovery Steps follow that and your problem will be Fixed it worked for me if you cant find the files you need NO_Vendor WM 5 Rom let me know al upload and post the link here for you ok
somehow i menage to turn on bootloader and then the phone was stack there i try to install wm 5 when go to 100% noting happens on the phone after hard reset
then i tray whit wm6 same there go fine on my pc till finish message appear and on the phone go till 100 % and i done hard reset and noting
then comes real problem my phone stop to charge my battery
he is now dead
on pins where should stand battery he show 0 voltage
and i come to dead end
if some1 now where to search for answers pls give me the link ty for your help in advance