my cingular ver is G4 ,
flash rom 100% completed,after reboot can't be power on.
so sad
What ROM did u flash? Can u go into bootloader mode (hold camera button, press soft reset)? What IPL/SPL do u have and did u do SoftSPL or HardSPL before flashing the ROM?
Did u have more than 50% battery before flashing? That sounds like the problem since it won't power on
thank u ,my friend
consulted the service,only way is change the DOC(Disk on chip).
to all :be care for Flashing Rom,learn more before you do it.
Related
Hi.
Sorry for my English. :-(
Upgrade ipl/spl to 2.61.11
http://www.romupdate.ru/index.php?option=com_remository&Itemid=27&func=fileinfo&id=383
After reboot no response anything.
How it switch in bootloader mode?
Thanks.
yappibiz said:
Hi.
Sorry for my English. :-(
Upgrade ipl/spl to 2.61.11
http://www.romupdate.ru/index.php?option=com_remository&Itemid=27&func=fileinfo&id=383
After reboot no response anything.
How it switch in bootloader mode?
Thanks.
Click to expand...
Click to collapse
What you have upgraded is Radio ROM, not IPL/SPL.
However if you have upgraded something else, maybe that is causing the problem.
You didn't explain what "no response" means. If the boot logo is shown, flash your original Qtek ROM to have everything restored to normal. If it does not power on, try to fully charge your phone (using wall charger). It that doesn't help than your may have a unrecoverable brick.
starkwong
Thanks for reply
No response = power button no active.
I up radio to 2.61.11 after reboot - brick.
CID is lock, G4.
- use your original wall charger to charge the phone fully, another miniusb wall charger will not work, does not have enough power.
- switch into bootloader mode (press and hold camera button and soft-reset, release soft-reset but hold camera a bit longer)
- in bootloader mode, install an original rom.
Good luck.
yappibiz said:
starkwong
Thanks for reply
No response = power button no active.
I up radio to 2.61.11 after reboot - brick.
CID is lock, G4.
Click to expand...
Click to collapse
Just flashing and upgrading Radio Rom doesn't Brick the phone,it doesn't include any IPL/SPL in it,unless you have flashed some rom with ipl/spl in it.Try to get the battery fully charged,hope it'll work out,otherwise,force the phone into bootloaders (tricolor screen) and flash the official stock rom from the carrier.
PLEASE help
I've flashed my Prophet to ROM Diamond..........
Everything was fine, instalation without any problem...
But when it was done, I've made a hard reset and than it just loads bootloader and nothing alse, when I tryed to flash-back the WM5 it writes that I haven't connected PDA to PC.
PLSSSSSSSSSSSSSSSSSS
Help !
connect USB lead press and hold camera button / press reset button still holing cam button a three colour boot screen should appear now you can re flash your ROM using the normal method
thanks
thank's for reply, I've tryed this but nothing happend, but the "NVID_RUU" has solved that. ;-) THXXX
where ?
and just onw more question.. where can I down the "HARD SPL" ? I've looked around but havent foud any...
I think this tool does the spl for you
Info
http://forum.xda-developers.com/showpost.php?p=2317108&postcount=1
Download here:
http://rs636.rapidshare.com/files/209950732/Prophet_Tools_2.8.3.zip
thX
thank's now its fully working and running on wm6.1
PLEASE SOMEBODY HELP ME
TWO WEEK AGO MY ATOM WAS DEAD
IAM HAVE BEEN TRY TO HARD RESET ALSO MN1 BOOT LOADER ( POWER BUTTON+CAMERA BUTTON). BUT DOESN'T WORK.
SO TODAY IAM TRY TO FLASH BOOT LOADER FROM JTAG PORT, AFTER FINISH FLASH PROGRAMED MY ATOM STILL DEAD.
SOMEBODY PLEASE HELP...
Okay, firstly dont put everything in caps.. its EXTREMELY annoying. Secondly, the device turns on correct? if it does then just try flashing from either your PC through Activesync OR via a memory card with a ROM on it. Consider using a stable ROM from either a ROM Chef or the O2/MWG website.
Aegishua said:
Okay, firstly dont put everything in caps.. its EXTREMELY annoying. Secondly, the device turns on correct? if it does then just try flashing from either your PC through Activesync OR via a memory card with a ROM on it. Consider using a stable ROM from either a ROM Chef or the O2/MWG website.
Click to expand...
Click to collapse
Haii.. thank you for your respon soon.
for your information my PDA totaly malfuction. that no respon when iam press power buton+camera buttonto go to MN1 boot loader .
only red lamp on when the PDA connect with charger battery.
Hmm okay.. so that means it still charges. You should try charging it for an extended period of time and then turning the device on. If the device comes up with the Manufacturer logo then you should just soft reset it and hold down your bootloader combination and go from there. However, if it doesnt even come up with the Manufacturer logo then you should consider getting it repaired.
Hii...i was do to charge my PDA also iam test with volt meter that battery is full power 4,2 volt dc.
So i try to push power button than my PDA doesn't start till now....
Atom Brick Solution...
suga_ngr said:
Hii...i was do to charge my PDA also iam test with volt meter that battery is full power 4,2 volt dc.
So i try to push power button than my PDA doesn't start till now....
Click to expand...
Click to collapse
Have you search on wiki?
I've been through that condition, last night actually when I pressed the wrong button (Power Button) when the MN1 bootloader looked for diskimg.nb0.
My device was near to death. I couldn't find the MN1 bootloader on my device's screen when I pressed the CAMERA+RESET(stylus). It remains dead until :
-I search the solution on http://wiki.xda-developers.com/index.php?pagename=ATOM_BRICK, I could see my device running its MN1 Bootloader
and looked for the ROM (diskimg.nb0) again and continued the ROM installation process
How to get the diskimg.nb0 please read this page :
http://wiki.xda-developers.com/index.php?pagename=ATOM_SDCARD
Maybe atom pure had the same step with atom exec when we try to solve the Brick Problem.
Cheers...
TOM PURE Dead
With my experience my atom was hardware broken.
somebody please tell me where i can buy atom hardware cause iam very love my atom...
try th!s tr!ck (cb ini mas)
yesterday 09 jan 10 it's happened same to me.
my case is downgrade from h3llow0rd1 6.1 to PD4v!et 19971 by m3dk!d.
then atom hang up.. dead! no screen, cann't boot or ON.. but still can charging
This tr!ck may be this could help u..
1. charging, look red lamp is on
2. then try replace battery, then put back on. it will blink (button call and end call will blinK)
3. with stylus try reset with pressing record button
4. if your lucky then it will show you boot loader screen
Now my atom is back again using Hell0w0rd R0M ... (^_^)
suga_ngr said:
With my experience my atom was hardware broken.
somebody please tell me where i can buy atom hardware cause iam very love my atom...
Click to expand...
Click to collapse
Entering BootLoader Mode:
1.Remove Battery
2.Press Camera button and hold it while insert the battery.
3.Press Reset with stylus (keep holding camera button)
If you're lucky, you'll be directed to bootloader mode.
try to push the power & camera button together while inserting the battery and then enter the bootloader mode camera+reset button.
My Atom Life (was) dead, too
..but only for awhile
this happened when I tried to flash this Bajok ROM.
I'm not new to flashing, but that kinda make me 'a little' careless this time.
I transferred the .dio file using active sync explorer while doing other stuff with my laptop.. soon after, I see that the file transfer is done, cause the window is closed. As usual, I do the rec button + reset ritual and flashed away..
I again continued my other works and got mesmerized in it for a moment or two.
Half an hour later I realized that my atom has been showing bootscreen for quite some time..
My first failed flash! Well, I thought, this is it...
Just to make sure, I pulled out the battery, put it back again and reboot.. still the same stuckness... Then, I figured that since this was caused by ROm flashing failure, why dont check the .dio file? So I did. I pulled out the memory card, put it in a card reader and explore it.. I notice that the .dio file is only 18 megs.. whatta..? The original .dio is like 70 megs, so it must had been transferred it incomplete.
So with high hope, I retrasferred the file, this time completely.
I inserted again the battery and repeated the rec button + reset ritual..
Boot loader appeared and flashed away like a charm!
Dear All
I have upgrade the atom with the atom rom WM6.5 21500. The rom was successfully upgraded but i don't like it. And when i tried to downgrade it to WM6.1, it didn't work. I have tried to enter bootloader but i can't, when the atom restart, they will not boot and restarting again and again. .
Please help in this matter..
thanks.
Qiky said:
Dear All
I have upgrade the atom with the atom rom WM6.5 21500. The rom was successfully upgraded but i don't like it. And when i tried to downgrade it to WM6.1, it didn't work. I have tried to enter bootloader but i can't, when the atom restart, they will not boot and restarting again and again. .
Please help in this matter..
thanks.
Click to expand...
Click to collapse
1. If your atom can goes into windows u can downgrade to 6.1 or 6.5 from my signature by using RUU from PDA viet.
2. If your atom can't goes into windows as well as boot loader, First you have to take out the battery for one or two minutes then put it back then try to enter boot loader again, if still not try the Second step by taking out the battery again then press and hold Reset + Camera button for one or two minutes then put battery back (keep pressing that button till u can see boot loader).
just want to add dolphin post
ur device is bricked, if and only if, ur device won't start normally... even if u press soft-reset, hard-reset, or even bootloader mode buttons. Before panicking, do da following:
Brick Test:
1. Make sure ur device has ample battery charge. If u're not sure plug it in with da wall charger for at least 10min
2. Remove ur battery for at least 1 minute
3. Replace ur battery while observing da LED lights
4. If da LED blinks once upon battery insertion, u might have hope yet
Da only way to upgrade on a semi-brick device, is to upgrade through bootloader mode. No bootloader mode, No upgrade possible - period.
Entering Bootloader Mode on Semi-Brick Atom:
1. Remove battery for for at least 1 minute
2. Press CAMERA+RESET(stylus) simultaneously
3. Insert battery while still holding da buttons
4. Release da buttons at da same time(u should see bootloader screen)
Note: Failure to hold the buttons at da same time during battery insertion will cause it not to work.
GOOD LUCK
dolphinxda said:
1. If your atom can goes into windows u can downgrade to 6.1 or 6.5 from my signature by using RUU from PDA viet.
2. If your atom can't goes into windows as well as boot loader, First you have to take out the battery for one or two minutes then put it back then try to enter boot loader again, if still not try the Second step by taking out the battery again then press and hold Reset + Camera button for one or two minutes then put battery back (keep pressing that button till u can see boot loader).
Click to expand...
Click to collapse
i follow all your step by step sugestion but it seems not working and i still cannot run into bootloader or switch to another O.S.
is there any other solutions you can give??
your help is very apprecciated.
knoxbrotherhood said:
ur device is bricked, if and only if, ur device won't start normally... even if u press soft-reset, hard-reset, or even bootloader mode buttons. Before panicking, do da following:
Brick Test:
1. Make sure ur device has ample battery charge. If u're not sure plug it in with da wall charger for at least 10min
2. Remove ur battery for at least 1 minute
3. Replace ur battery while observing da LED lights
4. If da LED blinks once upon battery insertion, u might have hope yet
Da only way to upgrade on a semi-brick device, is to upgrade through bootloader mode. No bootloader mode, No upgrade possible - period.
Entering Bootloader Mode on Semi-Brick Atom:
1. Remove battery for for at least 1 minute
2. Press CAMERA+RESET(stylus) simultaneously
3. Insert battery while still holding da buttons
4. Release da buttons at da same time(u should see bootloader screen)
Note: Failure to hold the buttons at da same time during battery insertion will cause it not to work.
GOOD LUCK
Click to expand...
Click to collapse
i follow all your step by step sugestion but it seems not working and i still cannot run into bootloader or switch to another O.S.
is there any other solutions you can give??
your help is very apprecciated.
dolphinxda said:
1. If your atom can goes into windows u can downgrade to 6.1 or 6.5 from my signature by using RUU from PDA viet.
2. If your atom can't goes into windows as well as boot loader, First you have to take out the battery for one or two minutes then put it back then try to enter boot loader again, if still not try the Second step by taking out the battery again then press and hold Reset + Camera button for one or two minutes then put battery back (keep pressing that button till u can see boot loader).
Click to expand...
Click to collapse
i follow all your step by step sugestion but it seems not working and i still cannot run into bootloader or switch to another O.S.
is there any other solutions you can give??
your help is very apprecciated.
Hi, firs sry for may bad english.
I download Proformance Rom (Proformance Rom { Long Battery Life + OC 1.15 Ghz + many more) from here.
And after i do everything like autor say, mobiles phone normali starts...after i reset phone, i can turn on phone.
When i press power button, there is vibratin for 1/2 sec, and notting happend...
Pls help me... THNX
EDIT:
i have locked BL
Do you did this before flash rom?
NOTE Since this Rom is using a custom kernel so it is only for UB if want to install on LB devices then just remove "boot.img" file from the zip file
Click to expand...
Click to collapse
Anyway I don't think is bricked when it vibrate. Try use flastool and flash stock rom.
First I set up where I deleted the boot.img, and everything is working OK, and then I went again to set rom, but I obviously marked with this boot.img
Now I can not turn on a cell phone, there is vibration, and when I go to a key combination power + volume down / up turns green or blue button for 3 seconds and that's it.
I think it just made the problem this boot.img
Can you please explain in more detail what should I do? thanks
ArterBO said:
First I set up where I deleted the boot.img, and everything is working OK, and then I went again to set rom, but I obviously marked with this boot.img
Now I can not turn on a cell phone, there is vibration, and when I go to a key combination power + volume down / up turns green or blue button for 3 seconds and that's it.
I think it just made the problem this boot.img
Can you please explain in more detail what should I do? thanks
Click to expand...
Click to collapse
the rom you are trying to use need unlocked bootloader ..... its a soft brick which u are facing , use flashtool to flash a stock ftf and dun keep on trying to turn on ur phone now , u'll just drain the battery which will make the process more complicated ....
To sum up :-
1) the error is fixable.
2)download official firmware ftf
3)flash it using flashtool
4)next time unlock bootloader before trying to flash a rom which uses custom kernel
Hello,
thank you all for your help.
I solved the problem on my way, so I unlocked the bootloader, and a cell phone power on without any errors.
Thank you all again.
Greeting from Croatia
ArterBO said:
Hello,
thank you all for your help.
I solved the problem on my way, so I unlocked the bootloader, and a cell phone power on without any errors.
Thank you all again.
Greeting from Croatia
Click to expand...
Click to collapse
its better to press thanks button to say thanks in xda