Hi.
Sorry for my English. :-(
Upgrade ipl/spl to 2.61.11
http://www.romupdate.ru/index.php?option=com_remository&Itemid=27&func=fileinfo&id=383
After reboot no response anything.
How it switch in bootloader mode?
Thanks.
yappibiz said:
Hi.
Sorry for my English. :-(
Upgrade ipl/spl to 2.61.11
http://www.romupdate.ru/index.php?option=com_remository&Itemid=27&func=fileinfo&id=383
After reboot no response anything.
How it switch in bootloader mode?
Thanks.
Click to expand...
Click to collapse
What you have upgraded is Radio ROM, not IPL/SPL.
However if you have upgraded something else, maybe that is causing the problem.
You didn't explain what "no response" means. If the boot logo is shown, flash your original Qtek ROM to have everything restored to normal. If it does not power on, try to fully charge your phone (using wall charger). It that doesn't help than your may have a unrecoverable brick.
starkwong
Thanks for reply
No response = power button no active.
I up radio to 2.61.11 after reboot - brick.
CID is lock, G4.
- use your original wall charger to charge the phone fully, another miniusb wall charger will not work, does not have enough power.
- switch into bootloader mode (press and hold camera button and soft-reset, release soft-reset but hold camera a bit longer)
- in bootloader mode, install an original rom.
Good luck.
yappibiz said:
starkwong
Thanks for reply
No response = power button no active.
I up radio to 2.61.11 after reboot - brick.
CID is lock, G4.
Click to expand...
Click to collapse
Just flashing and upgrading Radio Rom doesn't Brick the phone,it doesn't include any IPL/SPL in it,unless you have flashed some rom with ipl/spl in it.Try to get the battery fully charged,hope it'll work out,otherwise,force the phone into bootloaders (tricolor screen) and flash the official stock rom from the carrier.
Related
i have an ameo and it went dead. i can get it in the bootscreen or connect with usb. how can i get to the usb bootscreen. hard reset doesnt work then it says press action to restore factory default. but it doesnt do anything. i just want to get the rainbow screen with usb, just sop i can connect with sync or something else
please help me
Allready tried to put out your micro SD? And thenn do a reset?
Does your computer recognise your device when you plug it in?
What does the bootloader say your SPL is?
If the answer to the first question is yes then you should be able to flash one of the WM6 ROMS onto your device regardless of activesync. If your bootloader says you have Olipro's SPL then you can flash ANY ROM. Only found this out yesterday. If your device is a different spl then you'll have to install one which matches your CID.
Ameo Fix
Hold the Camera and Comm Manager button and press reset to load into Bootloader, then install ROM image
05mehmet said:
Hold the Camera and Comm Manager button and press reset to load into Bootloader, then install ROM image
Click to expand...
Click to collapse
make it and flashing sopp bei 1 %
ERROR(294): INVALID SELLER -ID
felix999
ATHE100
AOL-v1.00
ATHE100
SPL-v1.10.RP00
I have WM5.0
runing AthenaUnlocker
STEP1>>>all OK
STEP2>>>stop by 60 % and now can do nothing
only have bootloader and now corect rom...
please help???
felix999
when i power on my atom,
it only flash the orange led and never work anymore,
even if i reset or push the power button,
it happens nothing.
the only way make me think it's not a brick is to replace the battery,,
keep holding reset and center button then put the battery on and off many times,
then i put the battery on and release all buttons,
it goes into the bootloader,
then i connect atom with usb cable,
my computer shows unknown device.
johnjohn1977 said:
when i power on my atom,
it only flash the orange led and never work anymore,
even if i reset or push the power button,
it happens nothing.
the only way make me think it's not a brick is to replace the battery,,
keep holding reset and center button then put the battery on and off many times,
then i put the battery on and release all buttons,
it goes into the bootloader,
then i connect atom with usb cable,
my computer shows unknown device.
Click to expand...
Click to collapse
read the wiki...
Did you Flash a new ROM?
Regards,
Carty..
Carty said:
Did you Flash a new ROM?
Regards,
Carty..
Click to expand...
Click to collapse
yes
i flash a wm6 rom without reading the attention carefully
use spritebackup
Hi there,
If you plug the carger in and the red light shows, then it's charging. If this is the case you may be able to put it into bootloader and try again, but with proper rom.
hope this helps
2234jones said:
Hi there,
If you plug the carger in and the red light shows, then it's charging. If this is the case you may be able to put it into bootloader and try again, but with proper rom.
hope this helps
Click to expand...
Click to collapse
i can't flash my device with any rom
the bootloader seems have some problem
i can't use camera+reset to change into bootloader mode
johnjohn1977 said:
i can't flash my device with any rom
the bootloader seems have some problem
i can't use camera+reset to change into bootloader mode
Click to expand...
Click to collapse
remove your battery about 1-2 minutes and plug in back, after that try to press camera + reset.
my cingular ver is G4 ,
flash rom 100% completed,after reboot can't be power on.
so sad
What ROM did u flash? Can u go into bootloader mode (hold camera button, press soft reset)? What IPL/SPL do u have and did u do SoftSPL or HardSPL before flashing the ROM?
Did u have more than 50% battery before flashing? That sounds like the problem since it won't power on
thank u ,my friend
consulted the service,only way is change the DOC(Disk on chip).
to all :be care for Flashing Rom,learn more before you do it.
PLEASE SOMEBODY HELP ME
TWO WEEK AGO MY ATOM WAS DEAD
IAM HAVE BEEN TRY TO HARD RESET ALSO MN1 BOOT LOADER ( POWER BUTTON+CAMERA BUTTON). BUT DOESN'T WORK.
SO TODAY IAM TRY TO FLASH BOOT LOADER FROM JTAG PORT, AFTER FINISH FLASH PROGRAMED MY ATOM STILL DEAD.
SOMEBODY PLEASE HELP...
Okay, firstly dont put everything in caps.. its EXTREMELY annoying. Secondly, the device turns on correct? if it does then just try flashing from either your PC through Activesync OR via a memory card with a ROM on it. Consider using a stable ROM from either a ROM Chef or the O2/MWG website.
Aegishua said:
Okay, firstly dont put everything in caps.. its EXTREMELY annoying. Secondly, the device turns on correct? if it does then just try flashing from either your PC through Activesync OR via a memory card with a ROM on it. Consider using a stable ROM from either a ROM Chef or the O2/MWG website.
Click to expand...
Click to collapse
Haii.. thank you for your respon soon.
for your information my PDA totaly malfuction. that no respon when iam press power buton+camera buttonto go to MN1 boot loader .
only red lamp on when the PDA connect with charger battery.
Hmm okay.. so that means it still charges. You should try charging it for an extended period of time and then turning the device on. If the device comes up with the Manufacturer logo then you should just soft reset it and hold down your bootloader combination and go from there. However, if it doesnt even come up with the Manufacturer logo then you should consider getting it repaired.
Hii...i was do to charge my PDA also iam test with volt meter that battery is full power 4,2 volt dc.
So i try to push power button than my PDA doesn't start till now....
Atom Brick Solution...
suga_ngr said:
Hii...i was do to charge my PDA also iam test with volt meter that battery is full power 4,2 volt dc.
So i try to push power button than my PDA doesn't start till now....
Click to expand...
Click to collapse
Have you search on wiki?
I've been through that condition, last night actually when I pressed the wrong button (Power Button) when the MN1 bootloader looked for diskimg.nb0.
My device was near to death. I couldn't find the MN1 bootloader on my device's screen when I pressed the CAMERA+RESET(stylus). It remains dead until :
-I search the solution on http://wiki.xda-developers.com/index.php?pagename=ATOM_BRICK, I could see my device running its MN1 Bootloader
and looked for the ROM (diskimg.nb0) again and continued the ROM installation process
How to get the diskimg.nb0 please read this page :
http://wiki.xda-developers.com/index.php?pagename=ATOM_SDCARD
Maybe atom pure had the same step with atom exec when we try to solve the Brick Problem.
Cheers...
TOM PURE Dead
With my experience my atom was hardware broken.
somebody please tell me where i can buy atom hardware cause iam very love my atom...
try th!s tr!ck (cb ini mas)
yesterday 09 jan 10 it's happened same to me.
my case is downgrade from h3llow0rd1 6.1 to PD4v!et 19971 by m3dk!d.
then atom hang up.. dead! no screen, cann't boot or ON.. but still can charging
This tr!ck may be this could help u..
1. charging, look red lamp is on
2. then try replace battery, then put back on. it will blink (button call and end call will blinK)
3. with stylus try reset with pressing record button
4. if your lucky then it will show you boot loader screen
Now my atom is back again using Hell0w0rd R0M ... (^_^)
suga_ngr said:
With my experience my atom was hardware broken.
somebody please tell me where i can buy atom hardware cause iam very love my atom...
Click to expand...
Click to collapse
Entering BootLoader Mode:
1.Remove Battery
2.Press Camera button and hold it while insert the battery.
3.Press Reset with stylus (keep holding camera button)
If you're lucky, you'll be directed to bootloader mode.
try to push the power & camera button together while inserting the battery and then enter the bootloader mode camera+reset button.
My Atom Life (was) dead, too
..but only for awhile
this happened when I tried to flash this Bajok ROM.
I'm not new to flashing, but that kinda make me 'a little' careless this time.
I transferred the .dio file using active sync explorer while doing other stuff with my laptop.. soon after, I see that the file transfer is done, cause the window is closed. As usual, I do the rec button + reset ritual and flashed away..
I again continued my other works and got mesmerized in it for a moment or two.
Half an hour later I realized that my atom has been showing bootscreen for quite some time..
My first failed flash! Well, I thought, this is it...
Just to make sure, I pulled out the battery, put it back again and reboot.. still the same stuckness... Then, I figured that since this was caused by ROm flashing failure, why dont check the .dio file? So I did. I pulled out the memory card, put it in a card reader and explore it.. I notice that the .dio file is only 18 megs.. whatta..? The original .dio is like 70 megs, so it must had been transferred it incomplete.
So with high hope, I retrasferred the file, this time completely.
I inserted again the battery and repeated the rec button + reset ritual..
Boot loader appeared and flashed away like a charm!
Hi.
Just tryed to inst. Android in my HD2 and now it stuck with a white screen with the HTC logo.
Is it any way to fix this or do i just trach it?
I am not an expert but this happened to me once while installing SD android.
I reinstalled the original ROM from the HTC site and restored my phone to factory settings.
I tried another version of android and it worked well (since last September).
Only observation is that lately (last two month) my phone hangs a lot on both systems (droid & win) and overheats a lot and when this happens I need to wait for it to cool down (at least 20 minutes) then it accepts rebooting (I am stating this although I am not sure is it from the droid or just my HW is faulty for other reasons).
I hope this helps
I tryed a NAND install. Now I cant get conection with usb and computer
Maybe you can perform a hard reset with buttons
1. With the phone turned off, press and hold the VOLUME UP and VOLUME DOWN buttons, then press the END/POWER button shortly and release it.
2. Release the VOLUME UP and VOLUME DOWN buttons.
3. Press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset.
I hope it works
3mo said:
Maybe you can perform a hard reset with buttons
1. With the phone turned off, press and hold the VOLUME UP and VOLUME DOWN buttons, then press the END/POWER button shortly and release it.
2. Release the VOLUME UP and VOLUME DOWN buttons.
3. Press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset.
I hope it works
Click to expand...
Click to collapse
didnt work hehe still at the white htc logo screen. I migth installed the files the wrong way round?
Can you get to bootloader (3 coloured screen) by turning on the phone whilst holding vol down?
conantroutman said:
Can you get to bootloader (3 coloured screen) by turning on the phone whilst holding vol down?
Click to expand...
Click to collapse
Yes that's about the only thing i can do
Go-Fast said:
Yes that's about the only thing i can do
Click to expand...
Click to collapse
As long as you can get to bootloader its ok
I would start over from the begining.....
Does it still show that you have HSPL installed on bootloader?
If so, reflash the windows 6.5 ROM that you were using before the android flash.
Then follow the steps in this thread.
Hope that helps....
conantroutman said:
As long as you can get to bootloader its ok
I would start over from the begining.....
Does it still show that you have HSPL installed on bootloader?
If so, reflash the windows 6.5 ROM that you were using before the android flash.
Then follow the steps in this thread.
Hope that helps....
Click to expand...
Click to collapse
Thnx I'll try it later and report back
Still cant get my coputer to connect to the phone.
I get to the "red green and blue" screen, and it says
PB01100 HX-BC
SPL-2.00.HSPL 8G XE
0x85
CotullaHSPL 0x40
I'm on win7 SP1
Ok when you enter bootloader (red green blue screen) you should see "Serial" at the bottom..
When you connect to the computer it should change to "USB"
You might not see anything happen on your computer but the word at the bottom of the bootloader should change.
I might be mistaken here but Im pretty sure you need "2.08 HSPL" although your bootloader shows you have HSPL installed its not 2.08. This might be the cause of your original problem.
Once it says "USB" your ready to flash a ROM via USB as usual...
If it stays on "Serial" after a few minutes then try another USB port or computer if possible.
Enter bootloader and run the HSPL tool and choose 2.08HSPL......
Then start the process from the beggining.
Hope that helps.
conantroutman said:
Ok when you enter bootloader (red green blue screen) you should see "Serial" at the bottom..
When you connect to the computer it should change to "USB"
You might not see anything happen on your computer but the word at the bottom of the bootloader should change.
I might be mistaken here but Im pretty sure you need "2.08 HSPL" although your bootloader shows you have HSPL installed its not 2.08. This might be the cause of your original problem.
Once it says "USB" your ready to flash a ROM via USB as usual...
If it stays on "Serial" after a few minutes then try another USB port or computer if possible.
Enter bootloader and run the HSPL tool and choose 2.08HSPL......
Then start the process from the beggining.
Hope that helps.
Click to expand...
Click to collapse
Hah your a babe conantroutman lol thnx
Is this the rigth SPL ?
Not to intrude on conantroutman here but yes you have to have HSPL 2.08 and a 2.15.50.14 or 2.10.50.02 radio for MAGLDR to work. Without the HSPL 2.08 you can not flash MAGLDR and without the proper radio version MAGLDR will not even boot up.
So to answer your question yes the HSPL you have in the picture you posted is the correct HSPL.
Yep as T said, hspl is good, radio is good. Your all set.
That guide for installing android at the top of the thread is pretty damn good and will have you up and running in no time. Let us know how you get on
Sent From My Fingers To Your Face.....
thnx to both of you. I'll post here when done
Crap my call button dont work when I'm in bootloader
When your in the MAGLDR menu?
You may have to flash WM again to test the call button. Or try reflashing MAGLDR, that may help...
Sent From My Fingers To Your Face.....
I guesse it's a lost case so I just installed winmo and runing android from SD card
thnx for the help.
btw!
is there a way to get htc sense to work on a huawei u8800 or x5?
Hmmm its very weird because if your call button works in WM then it should work in MAGLDR....