hello
my p3401 is dead after use spl and hard spl please help me
or my cheff kill me
Read this and follow.
http://forum.xda-developers.com/showthread.php?t=472169
how to revive
Please do not connect my p3401 so the blue light is lit and not in the hot sync signal nen t nen to hard reset and it could revive
(ps: led is orange AND BLUE)
Related
please plesae help my spv m3100 flashed wrong
now my phone stop on boot screen and i want to reflash it but it stop on 1 %
my ipl is 1.04
and my spl is 2.03
now what is the solution for me
dvdaio said:
please plesae help my spv m3100 flashed wrong
now my phone stop on boot screen and i want to reflash it but it stop on 1 %
my ipl is 1.04
and my spl is 2.03
now what is the solution for me
Click to expand...
Click to collapse
Try a couple things...
1. Hard Reset
2. Flash a ROM starting at the botloader screen on the phone (put in bootloader, THEN plug into USB)
3. Use mtty, try the task 28 command.
Your solution like everyone else that has bricked there phone on this forum is to start reading. Start with the WiKi and then the 100 page thread on unbricking phones. I'm sure you have a few long hours ahead of you but there is hope at the end of the tunnel
Austinsync speaks truth in abundance! Your first stop should be the excellent unbricking table that dear old Pof compiled, this is in the WIKI and if you are lucky you won't have to go much farther than that...
Hi
My Tytn is stuck at the bootscreen ( Welcome to WM6). I'm usint TNT 2.0 Rom.
my green up right light is flashing and my wifi up left light is flashing to.
i'm using spl 2.10
Pls help me and let me know ( if possible ) what to do
Thank you in advance
Have a look in here.
WB
http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
Hard Reset.
Hello everyone.
I try to do this in english but its not so goog.
I have a T-Mobile MDA Vario II.By flashing the rom from WM5 to WM6 the flashing tool displace at 66 % that usb is not available. then ich have the tri coloured screen.i tried with mtty.exe to reset it to the old os.but now my phone only show the t mobile boot screen and freeze.can anyone help me to unbrick it ??
try reading the wiki:
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
hi everybady, i have Vista and herm200, that's brick i try everythink whire here and the herm200 is still brick, pls give me the right way to unbrick with vista. ipl-1.01 spl-1.09, red green blue white-serial/usb, the program mtty is not working ( only com1 and com2 displayed )
thank's
re
it's alive, thank's for help
how did you fix it ?'
how did u fix ur herm i also have thesame problem
Hi,
I wanted to downgrade my SPL3.5 and was preparing the device. I opened the battery slot, took out the battery, SIM and SD and put back the battery.
Since then the Athena won't turn on anymore.
What I did wrong: I did all of this with the USB cable connected.
I tried softreset, hardreset and nothing.
With Athena connected to Power, led will flash red when I reset. If i remove battery and connect to USB, red led will be permanently on.
Any ideas.
EDIT1:
Can it be that the battery is somehow corrupted? Unfortunatly I don't have another. Can one like reset the battery? Or do some tests on it, decharge it, etc?
Thanks,
vma
PS: The reason I did SPL1.2 > SPL3.5, tried AP40, tried WM6.5 and want to go back is that I am in bed at home with the flue (probably H1N1). And now I am totally pissed off, because my Athena won't work... arggghhhhh
It's alive again...
http://forum.xda-developers.com/showpost.php?p=1804252&postcount=9
Ufff!!!
Cheers,
vma
Help, i have a problems. Dead athena!!!
PDA is not flash, hangs up on 1%, then error device id
Athe 100
IPL v.2.02
Athe 100
my SPL 1.10.0000
Serge94 said:
Help, i have a problems. Dead athena!!!
PDA is not flash, hangs up on 1%, then error device id
Athe 100
IPL v.2.02
Athe 100
my SPL 1.10.0000
Click to expand...
Click to collapse
Serge your phone is not unlocked!
you need to flash back to the orignal rom frst then do the unlocker before flashing another rom
read the beginners guide