I updated my bootloader to SPL 2.47 and than upgraded my radio to 3.37.75 with success. After a hard reset the phone shows the splash screen with the new radio for a few seconds and then hangs up on the plain verizon screen. I can get into bootloader (I have reflashed about five times now and tried a few different radios 3.37.2 and the same issue remains) ????
Sounds like you have to add the rom now. So flash the rom image.
drewcam888 said:
Sounds like you have to add the rom now. So flash the rom image.
Click to expand...
Click to collapse
I think the same thing.
Just another observation way add the old Verizon radio. Why not 3.42.40 or 3.42.50?
Yeah I still had the stock rom installed. I expected it to function without the rom update. I am going to flash to dcd's 3.2.6. Which radio do you guys suggest for verizon?
drewcam888 said:
..Why not 3.42.40 or 3.42.50?
Click to expand...
Click to collapse
For radios. You can't upgrade to a gps radio with a non gps rom. Sounds like a good way to brick your phone. Maybe read up before you flash again.
How do you establish active sync?
Plug the phone into a computer with activesync installed on the computer.
Never mind the active sync ? had to just take out the darn sd card
Related
I have an new titan, and it has spl-1.20.olipro bootloader.. I am trying to reflash but it reboots at 11%. I can't get any roms to fully flash.. It's stuck on the HTC black screen and say's not radio..
I need help.. how can i fix this cux i can't get any roms to flash... cooked or official
use the boot loader in the guide bellow
follow this guide and start all over
it was stuck in 1.2 olpro. I cant get any rom to flash or update to 2.40... I tried to flash radio 3.27.. that went 100% but now the phone won't even turn on
do you get a charge light when you plug it in to the wall? if so make sure its not dead, ya never know.. lol
no i don't get anything.. no charge light or anything.. it dead
yeah sounds like a brickk... sorry =\
take it in and try to get another one
jmann76 said:
it was stuck in 1.2 olpro. I cant get any rom to flash or update to 2.40... I tried to flash radio 3.27.. that went 100% but now the phone won't even turn on
Click to expand...
Click to collapse
***EDIT***
Dang, I just read your post about your light not even turning on. Did you try soft resetting it? I know that sounds dumb, but had to ask. Did you try taking the battery out for a bit? Try holding the Power button and the Camera button down on the right side of the phone and push your stylus into the soft reset hole. That's the way to put it into bootloader mode. If you've got the phone plugged in even (try it without the battery too) and you still don't get anything, then I'd say try to get it replaced if you can. That's never a good feeling. I've had a couple of HTC devices now, and have been there a couple of times where you think your phone is dead, but it ends up not being that way. I hope this situation goes the same way for you.
*********************************
3.27 requires 2.40 and is also outdated.
You could try the Titan Relocker to put an older bootloader version on it, and then flash an official rom that supports GPS, which will update you to the Carrier's ROM and Radio. At that point, you can try to unlock and flash to 2.40.
Once you have 2.40 installed, you can then put on a 3.xx radio (3.39.10 is recommended right now) and flash to a custom ROM, such as DCD's newly released 3.1.6 ROM. I think it runs really well, and I flash mine to different roms way more than I'd like to admit. I think I'm going to stay with this one for a while.
Once you get the 2.40 bootloader, I'd start using the SD Card flashing method for your ROMs exclusively. It works really well, and the good thing is that you can have other stuff on the card, so you can use a small card by itself only for flashing, with folders for different ROMs and Radios, or you could use one big one, and then just change the required file every time you wanted to flash.
I haven't included links to everything because that would take a while, but you should be able to find everything I've mentioned by using the search function, or if you can't seem to find what you're looking for here, you can try ppcgeeks.com too, it's another great resource for our phones.
Good luck!
-kmart
P.S. Don't worry too much about your phone, these titans are actually quite hard to brick. As long as you can get to the bootloader, you should have a good chance to get everything working properly again.
jmann76 said:
I have an new titan, and it has spl-1.20.olipro bootloader.. I am trying to reflash but it reboots at 11%. I can't get any roms to fully flash.. It's stuck on the HTC black screen and say's not radio..
I need help.. how can i fix this cux i can't get any roms to flash... cooked or official
Click to expand...
Click to collapse
You are fine. Though as your Titan is already unlocked and had an older third-party ROM installed, it ain't so "new" . Your problem is covered in the Wiki:
II. Install the correct bootloader
Hit Power-Camera-Reset to check what version of bootloader you have installed.
At the tri-colour bootscreen you will see the version number installed.
if it is 1.04 or 1.06 then you must unlock your phone and upgrade to 2.40. Olipro 1.20 is not necessary at all when using newer ROMs/Radios.
if it is 1.20 then you have the pre-GPS ROM bootloader and must first flash to one of the older ROMs and associated radio to boot into WM, get an ActiveSync connection and then upgrade to 2.40.
if it is 2.40 then you have the correct bootloader and are ready to move on to the Radio Upgrade in Section III.
michaelm91 said:
use the boot loader in the guide bellow
Click to expand...
Click to collapse
Guys, the info first presented in that thread is out of date and not maintained. Please let it disappear and first direct people in help to the Wiki.
jmann76 said:
...that went 100% but now the phone won't even turn on
Click to expand...
Click to collapse
Oops, I just read that too... Remove the battery or try another battery yet? Other than that...
how did things finally turn out jmann?
Hey all,
Been trying just about everything to help a buddy out, but I've been failing repeatedly.
He got a brand new phone yesterday and found the XDA Titan Wiki to install the GPS enabled ROMs. He loaded SPL 2.4, then installed DCD 3.2.0. It got stuck at the Verizon screen when it restarted...then he apparently downloaded the Radio 3.42.30 to try and install that to get out of it (maybe thinking the Radio needed to be installed for it to get through). Now he's stuck at the White Verizon screen, and it says "No Radio".
Sounds like from when I read the Wiki he was supposed to install an intermediary Rom before jumping all the way to 3.2.0.
I've suggested using the Olipro SPL 1.2 unlocker, the Titan Relocker, several different ROM's and am at a loss as to how to fix it. He's still stuck at the Verizon screen displaying "No Radio."
Any suggestions?
Thanks
I went from stock to 3.2.0 / Radio 3.42.02.. no problems.
I have not loaded 2.42.30 (I prefer to use the radio version released by HTC for this device.. 3.42.30 was released for another device and ported.. although it seems to work for everyone.)
I HAVE read that for radio 3.42.30 you need SPL 1.20 for USB Flashing.
gc14 said:
Yeah 1.20 is needed to flash these radios via USB. Just need to put 2.40 back when you're done.
Click to expand...
Click to collapse
Based on that.. I assume SD flashing is ok with 2.40.
scotcha12345 said:
... (maybe thinking the Radio needed to be installed for it to get through)....
Click to expand...
Click to collapse
Yes! This is well documented.. a common issue.
If you flash the Rom without a compatible radio.. you will get stuck on the verizon screen... I suggest flashing the ROM AFTER the radio.. since you flashed the Rom already... when you get the radio working, Reflash the ROM.
Did you flash the radio via SD Card or USB?
Did it show a progress bar while flashing?
Let us know how your attempting to flash the Radio (USB or SD) With specific steps (held buttons X, Y, and Z.. saw this message, pressed this key.. saw this on the screen) .. and someone will let you know what you might be doing wrong.
Also.. dont forget to run the carrier cab when your done.. This is worth mentioning since it's the most common issue once the device boots and you cant program the phone, or make data / voice connections.
scotcha12345 said:
Hey all,
Been trying just about everything to help a buddy out, but I've been failing repeatedly.
He got a brand new phone yesterday and found the XDA Titan Wiki to install the GPS enabled ROMs. He loaded SPL 2.4, then installed DCD 3.2.0. It got stuck at the Verizon screen when it restarted...then he apparently downloaded the Radio 3.42.30 to try and install that to get out of it (maybe thinking the Radio needed to be installed for it to get through). Now he's stuck at the White Verizon screen, and it says "No Radio".
Sounds like from when I read the Wiki he was supposed to install an intermediary Rom before jumping all the way to 3.2.0.
I've suggested using the Olipro SPL 1.2 unlocker, the Titan Relocker, several different ROM's and am at a loss as to how to fix it. He's still stuck at the Verizon screen displaying "No Radio."
Any suggestions?
Thanks
Click to expand...
Click to collapse
Can you get to the bootloader by holding down camera power and pushing the reset button? If so, you can flash the radio with the SD method found in the wiki. just put the radio on the sd card in the proper format and enter bootloader and it should correct your problem.
Can I suggest something to try? (assuming you have 6800)
1. Get the sprint release. http://forum.xda-developers.com/showthread.php?t=402887
2. in bootloader, load the sprint release by usb method. when it gets to having you touch the screen, soft reset.
3. In bootloader, load the dcd 3.2.0 rom (or any other rom).
4. Hard reset.
This should give you 3.2.0 rom and 3.42.02 radio.
Responses
Hey guys,
Thanks for the responses and suggestions.
1) At the moment he doesn't have an SD card aside from the SDHC, so he couldn't do that until he purchases one. Good idea though if nothing else works
2) When pressing the camera/power/reset he's in the SPL 2.4 bootloader screen, he's going to try your suggestion of downloading Sprints and upgrading.
3) I'll ask him procedurally what else he has tried, what error he gets for recording. No doubt you were correct about uploading the Radio before the ROM
I've actually flashed my phone exactly the same way he has so that I can try to experience the same problems, and try to figure it out myself.
Bingo
Hey,
The Sprint ROM .exe was the answer. Very smart, thanks again for helping us both out. Was getting a little nervous for about 2 minutes.
useful=helper++
I did the same thing. Thank you very much...saved my butt!
BC
its alive
spreeway said:
Can I suggest something to try? (assuming you have 6800)
1. Get the sprint release. http://forum.xda-developers.com/showthread.php?t=402887
2. in bootloader, load the sprint release by usb method. when it gets to having you touch the screen, soft reset.
3. In bootloader, load the dcd 3.2.0 rom (or any other rom).
4. Hard reset.
This should give you 3.2.0 rom and 3.42.02 radio.
Click to expand...
Click to collapse
you saved my titan...thanks guy!
i was with DCD 3.2.5 and wanted to flash to new telus wm6.1 from telus... now i'm stuck with bl spl-2.07...tried to flash back with stock rom Telus_HTC_P4000_WM6_07252007 but at 1% it says not compatible...tried also uni_exitbootloader but nothing happen...whenever tried to flash with SD card...it's always keep saying "loading...", is anyone have suggestion to bring back my mogul to life?
thanks
uhh 2.07 is a relocker SPL
I think you have to downgrade to a stock firmware/SPL, then do the process properly.
Use SPL 2.40 or 2.47 before trying to flash on a GPS rom.
scrawnyb said:
uhh 2.07 is a relocker SPL
I think you have to downgrade to a stock firmware/SPL, then do the process properly.
Use SPL 2.40 or 2.47 before trying to flash on a GPS rom.
Click to expand...
Click to collapse
I would say the same. I would go ahead and unlock OliPro 2.4 (never tried 2.47) then flash Telus rom. After doing so you should be fine.
scrawnyb said:
uhh 2.07 is a relocker SPL
I think you have to downgrade to a stock firmware/SPL, then do the process properly.
Use SPL 2.40 or 2.47 before trying to flash on a GPS rom.
Click to expand...
Click to collapse
what do you mean by "I think you have to downgrade to a stock firmware/SPL" ? du you have any recommendation ?
belmont said:
what do you mean by "I think you have to downgrade to a stock firmware/SPL" ? du you have any recommendation ?
Click to expand...
Click to collapse
Sorry, I read his post wrong. HEre is what I would do:
1. Download OliPro 2.40 and run it. Ignore the part that asks you to verify the Active Synch connection. Its not needed for anything but a connection confirmation.
2. After running OliPro 2.40 you should be stuck at the three color bootloader screen, Like you are now. If not hold Camera and Power and use stylus to put phone in bootloader. Make Sure it says OLIPRO 2.40 for the version on the bootloader. If not then re-run oliupro and make sure to follow the directions. Especially noting that it asks you to disconnect then reconnect the device.
3. Flash your Stock ROM back.
4. Hard Reset.
In my experience you do not have to go back to a stock ROM to flash a new carrier ROM as long as you have OliPro.
Let me ask you this: What exact steps did you take when you flashed Telus ROM image?
I was on the same setup you were, DCD 3.2.5 with Radio .50 and OliPro 2.40. I simply flashed the Telus image and all was well for me. Hell it was better than all well. This is the best ROM I have ever used. PERIOD. No, its not pretty but damn, its fast as anything I have used and the GPS is insane!
BTW: Im a Verizon user. Anyone know how to make the phone not say "Telus" when I go to the connection manager?
scrosler said:
Sorry, I read his post wrong. HEre is what I would do:
1. Download OliPro 2.40 and run it. Ignore the part that asks you to verify the Active Synch connection. Its not needed for anything but a connection confirmation.
2. After running OliPro 2.40 you should be stuck at the three color bootloader screen, Like you are now. If not hold Camera and Power and use stylus to put phone in bootloader. Make Sure it says OLIPRO 2.40 for the version on the bootloader. If not then re-run oliupro and make sure to follow the directions. Especially noting that it asks you to disconnect then reconnect the device.
3. Flash your Stock ROM back.
4. Hard Reset.
In my experience you do not have to go back to a stock ROM to flash a new carrier ROM as long as you have OliPro.
Let me ask you this: What exact steps did you take when you flashed Telus ROM image?
I was on the same setup you were, DCD 3.2.5 with Radio .50 and OliPro 2.40. I simply flashed the Telus image and all was well for me. Hell it was better than all well. This is the best ROM I have ever used. PERIOD. No, its not pretty but damn, its fast as anything I have used and the GPS is insane!
BTW: Im a Verizon user. Anyone know how to make the phone not say "Telus" when I go to the connection manager?
Click to expand...
Click to collapse
thanks for quick reply. i tried so many times to use olipro 2.40...whenever i ran it...it popup that device is not connected and asked me to try again...tried also with SD but still hung on tri-color bars
belmont said:
thanks for quick reply. i tried so many times to use olipro 2.40...whenever i ran it...it popup that device is not connected and asked me to try again...tried also with SD but still hung on tri-color bars
Click to expand...
Click to collapse
Thats interesting. I have hosed so many XV6800's and used OliPro and a stock GPS sprint ROM to get them back (Thanks alot for nothing Verizon!).
IM assuming you are still on the tricolor screen? Take out battery and place back in. Then try again. Dont wait long. Someonelse has discoverd the phone can only be connected for so long before it "drops" connection with the windows machine. Someone else's therory but I can certainly second it.
What SPL were you using with DCD 3.x before upgrading?
scrosler said:
Thats interesting. I have hosed so many XV6800's and used OliPro and a stock GPS sprint ROM to get them back (Thanks alot for nothing Verizon!).
IM assuming you are still on the tricolor screen? Take out battery and place back in. Then try again. Dont wait long. Someonelse has discoverd the phone can only be connected for so long before it "drops" connection with the windows machine. Someone else's therory but I can certainly second it.
What SPL were you using with DCD 3.x before upgrading?
Click to expand...
Click to collapse
before flashing to new telus wm6.1 rom, i had olipro 2.40 with .30 radio and dcd3.2.5 kitchen...i have tried upgrading to radio .50 with no success. but failing to update radio didn't affect anything to my phone. tried your suggestion by romoving battery and still telling me that device not connected.
belmont said:
before flashing to new telus wm6.1 rom, i had olipro 2.40 with .30 radio and dcd3.2.5 kitchen...i have tried upgrading to radio .50 with no success. but failing to update radio didn't affect anything to my phone. tried your suggestion by romoving battery and still telling me that device not connected.
Click to expand...
Click to collapse
Hmmm, maybe try a different USB port at this time. Also, try this...
Before you connect your device open device manager in Windows. Look for M/S USB sync to appear after you connect. What OS are you using? This is what it will look like in Vista.
In XP I beleive it will show up under USB at the very bottom of Device Manager.
Does the phone show up at all?
Flash a stock pre-gps rom first.....then go ahead and upgrade the hard spl to 2.4 or 2.47.....then flash away with whatever you want....
You cannot flash Hardspl to Hardspl...they have overwrite protection not signed by HTC....
..................................
I currently have a Verizon Wireless fully flashed to cricket XV6800. I decided to know about hacking the Mogul so what I try to do was Look up WMDC 6.1 and apply it to my phone. When i did this the screen stopped at 11%. I took out the battery and tried to turn it on and i get a Red, Green, and Blue color on the start up screen. The words that are on the phone are TITA100 SPL-1.20.Olipro and on the bottom it says USB when connected and Serial when not connected. I looked every where to and figure it out how to get my phone back to the same way. I downloaded so many programs like Titan Unlocker, Titan exitbl, but all these programs do is say my phone is not connected when it is connected. I hear the Sound when the connection for the USB is connected and disconnected. What can i do Will i ever get my phone back to the same state that it once was. I was wondering also that since my phone was flashed that the software will be erased. Is there any way that I can get my Cricket Service. By the way before i did all the hacking what i did was back everything up on the memory card. Is there a way I can restore that through the phone even though i cant access the menu?
I'm going crazy--Thank you for your time to read and for those who can give me some word of advice or some way that my problem can be solved.
Thank you
if u are using xv6800.. i believe u have to install bootloader 2.40 or 2.47.. maybe that might be the problem when installing wm6.1
First, your phone is not bricked.. bricked means broken.. unfixable.. a brick!
You also need to let us know what you software you want to run... DCD 3.2.6?? WMDC 6.1 is Windows Mobile Device Center.. it's not a rom?? So I dont know what you tried to flash.
You need to read the instructions!! Sounds like You upgraded your rom (or tried to) with a non compatible bootloader.. if you dont want to bust your $200 - $500 phone perminently.. you should read the directions twice.. (I read them 4 times, then asked questions before the first time I flashed mine)
When you plug in the device and hear the usb sound.. check device manager.. make sure you see a usb device.. Your OS shoul have installed drivers... Then try the info below.
scrosler said:
1. Download OliPro 2.40 and run it. Ignore the part that asks you to verify the Active Synch connection. Its not needed for anything but a connection confirmation.
2. After running OliPro 2.40 you should be stuck at the three color bootloader screen, Like you are now. If not hold Camera and Power and use stylus to put phone in bootloader. Make Sure it says OLIPRO 2.40 for the version on the bootloader. If not then re-run oliupro and make sure to follow the directions. Especially noting that it asks you to disconnect then reconnect the device.
Click to expand...
Click to collapse
After that you can Flash a Radio, then a rom (I recommend the SD method)
And the versions in my signature.
You can get the SPL 2.40 here:
http://www.lifesnotsogood.com/dcd1182/titan/spl/
You should also read this WIKI
http://wiki.xda-developers.com/index.php?pagename=TitanProblems
If you cant flash SPL 2.40 you will need to flash back to a ROM compatible with SPL 1.20
Read here: http://forum.xda-developers.com/showthread.php?t=392133
I'd try to grab one of thoise older Roms and flash using SD card method.
Then from within Windows Mobile (on your device) Upgrade bootloader to 2.47 (Available from the same link as 2.40 above)
Then flash the radio and rom version I have in my signature.
And dont forget to install carrier cab.
I can't seem to connect my xv6800 to the computer so I can run that program.
I plug it in and the sound comes up and I run the program but it says that it can't copy to device.
loc37 said:
I plug it in and the sound comes up and I run the program but it says that it can't copy to device.
Click to expand...
Click to collapse
Then you need to get a Rom and radio compatible with SPL 1.20.. You'll need a SD card thats Equal to or less than 2GB (NON SDHC)
Check the compatibility here: http://forum.xda-developers.com/showthread.php?t=392133
Read the instructions for flashing this here:
http://wiki.xda-developers.com/index.php?pagename=TITAN_GettingStarted
Check the Flashing with a SD card section.
Process is the same for the radio and the rom.
I cant seem to find an available rom that you need though.. I'll post back when i do.
Unless someone else has a trick for you...
You can also try a another machine that may recognize your phone.
What did you actually try to flash your phone with, and how did you do it.. this is important to help you.
Download DCD 1.6.10 and flash it to your device with the SD card method (Instructions and links in my previous Post) I couldnt find the rom, but I downloaded the kitchen and cooked a rom that should work for you.
Download it from my webserver here:
http://x51.nx-1.com/TITAN/Roms/
Remember you need a proper SD card for this.. if you don't have one, you'll need to buy one.
After flashing this rom.. Assuming your radio is compatible... You should boot into the OS (forget making calls or getting data connection) Just download SPL 2.47 and execute it on your device.. once the SPL is upgraded, Flash the newest Radio, flash the newest rom, run the carrier cab, install aplications..
Let me know if you run into trouble.
okay so what I did was cook up a ROM and then added the Radio 3.37 from alltel on it. I restated the phone and waited the windows mobile 6.1 load screen did not change I moved my keyboard and the sound functioned. I did a restart a hard reset everything I believe it is something with the rom. Any suggestions?
Thanks
loc37 said:
okay so what I did was cook up a ROM and then added the Radio 3.37 from alltel on it. I restated the phone and waited the windows mobile 6.1 load screen did not change I moved my keyboard and the sound functioned. I did a restart a hard reset everything I believe it is something with the rom. Any suggestions?
Thanks
Click to expand...
Click to collapse
Hello loc...try here>>>>http://www.jrstreet.com/flash/burgertime.htm it's a tutorial made by burgertime from howard forums in the cricket section and it's a vid so you can just got through the steps if you get confused..i'm with cricket as well...try here for mms settings that will get your pic/vid messaging working if you have the software installed>>> http://forum.ppcgeeks.com/showthread.php?t=25859 and here is a rom for cricket if you dont wanna try and cook your own just yet>>> http://forum.ppcgeeks.com/showthread.php?t=18836 i love the new dcd 326 which is what i use but in order for me to get my pic/vid messaging working i had to include an oem version of arcsoft when i cooked my rom and vetvito's rom includes everything that you would neeed so you only need to put in the correct seetings plus you need the correct bootloader(olipro 2.40 or nuespl 2.47) and a radio 3.35 or higher...thanks guys and i hope everyone enjoys the weekend and loc i hope that you get it working...by the way loc there is a cricket forum http://howardforums.com/forumdisplay.php?f=336 and a sub forum for pda's that are flashed to cricket
im1badazchick said:
Hello loc...try here>>>>http://www.jrstreet.com/flash/burgertime.htm it's a tutorial made by burgertime from howard forums in the cricket section and it's a vid so you can just got through the steps if you get confused..i'm with cricket as well...try here for mms settings that will get your pic/vid messaging working if you have the software installed>>> http://forum.ppcgeeks.com/showthread.php?t=25859 and here is a rom for cricket if you dont wanna try and cook your own just yet>>> http://forum.ppcgeeks.com/showthread.php?t=18836 i love the new dcd 326 which is what i use but in order for me to get my pic/vid messaging working i had to include an oem version of arcsoft when i cooked my rom and vetvito's rom includes everything that you would neeed so you only need to put in the correct seetings plus you need the correct bootloader(olipro 2.40 or nuespl 2.47) and a radio 3.35 or higher...thanks guys and i hope everyone enjoys the weekend and loc i hope that you get it working...by the way loc there is a cricket forum http://howardforums.com/forumdisplay.php?f=336 and a sub forum for pda's that are flashed to cricket
Click to expand...
Click to collapse
Okay what i have done now is loaded my own personal ROM and then added 3.42.02 Radio to it. The only problem with that is that it keeps restarting and restarting its really weird. Is there any way that i can fix that?
Thank you
loc37 said:
Okay what i have done now is loaded my own personal ROM and then added 3.42.02 Radio to it. The only problem with that is that it keeps restarting and restarting its really weird. Is there any way that i can fix that?
Thank you
Click to expand...
Click to collapse
do you have one of the correct bootloaders? because just flashing to a custom rom and adding a new radio doesn't give you the bootloader that you need so you have to have that too...you can check it by holding down the power button, the camera button and inserting your stylus into the soft reset hole at the bottom of the phone and to get back out of it just do a soft reset but it needs to be be either 2.40 or 2.47 not 1.20 or anything else
im1badazchick said:
do you have one of the correct bootloaders? because just flashing to a custom rom and adding a new radio doesn't give you the bootloader that you need so you have to have that too...you can check it by holding down the power button, the camera button and inserting your stylus into the soft reset hole at the bottom of the phone and to get back out of it just do a soft reset but it needs to be be either 2.40 or 2.47 not 1.20 or anything else
Click to expand...
Click to collapse
When I turn off my phone it says 1.20. What can i do to change it? What software should i Download?
Thank You very Much
loc37 said:
When I turn off my phone it says 1.20. What can i do to change it? What software should i Download?
Thank You very Much
Click to expand...
Click to collapse
......flash a stock pre-gps rom and then upgrade the bootloader to 2.47........then flash whatever you like....
flyers2114 said:
......flash a stock pre-gps rom and then upgrade the bootloader to 2.47........then flash whatever you like....
Click to expand...
Click to collapse
Okay I solved that problem but now when I click on the settings option on the menu my phone freezes. What can be the cause of that? Did I cook the ROM wrong?
Thanks
loc37 said:
Okay I solved that problem but now when I click on the settings option on the menu my phone freezes. What can be the cause of that? Did I cook the ROM wrong?
Thanks
Click to expand...
Click to collapse
Usually that means you have the wrong build of MSVC installed use build 19209...
loc37 said:
Okay I solved that problem but now when I click on the settings option on the menu my phone freezes. What can be the cause of that? Did I cook the ROM wrong?
Thanks
Click to expand...
Click to collapse
if you now have the correct bootloader and radio...try flashing with a pre-cooked rom like dcd 326 or the rom from the links that i gave you...the popular one was the black pill and there is one that's specifically for cricket
do I just google that build number or is there a specific program I should download?
Thanks
loc37 said:
do I just google that build number or is there a specific program I should download?
Thanks
Click to expand...
Click to collapse
LOL..no if you lookk about five post up you will see DCD 326 and as for the other from vetvito it was in one of the links that i first posted for you
loc37 said:
When I turn off my phone it says 1.20. What can i do to change it? What software should i Download?
Thank You very Much
Click to expand...
Click to collapse
Did you read any of my posts...
Hrm.. could have sworn I addressed this already.
x51 said:
You can get the SPL 2.40 here:
http://www.lifesnotsogood.com/dcd1182/titan/spl/
Click to expand...
Click to collapse
x51 said:
Then from within Windows Mobile (on your device) Upgrade bootloader to 2.47 (Available from the same link as 2.40 above)
Then flash the radio and rom version I have in my signature.
Click to expand...
Click to collapse
I included links, and all the information you would need.. (Like the Rom/Radio/SPL compatibility list) yet you didn't read it.
I spent time finding those links, downloading a rom.. cooking it for you, and uploading it to my webserver so you can download it.
x51 said:
Download DCD 1.6.10 and flash it to your device with the SD card method (Instructions and links in my previous Post) I couldnt find the rom, but I downloaded the kitchen and cooked a rom that should work for you.
Download it from my webserver here:
http://x51.nx-1.com/TITAN/Roms/
Remember you need a proper SD card for this.. if you don't have one, you'll need to buy one.
After flashing this rom.. Assuming your radio is compatible... You should boot into the OS (forget making calls or getting data connection) Just download SPL 2.47 and execute it on your device.. once the SPL is upgraded, Flash the newest Radio, flash the newest rom, run the carrier cab, install aplications..
Let me know if you run into trouble.
Click to expand...
Click to collapse
I also explained that once you boot into windows with that rom, you need to upgrade your bootloader to 2.47 (with instructions) and then your radio, and then rom.
The path was simple..
Flash dcd 1.6.10 (compatible with SPL 1.20) so the phone will boot
Upgrade SPL (bootloader to 2.47)
Flash new radio (3.47.50)
Flash new Rom (3.2.6)
Run carrier cab.
If you are still asking about where to get the (SPL) bootloader.. I guess I cant help you....
I've recently upgraded to the new official TMOUS ROM and now wanted to install OzROM_5.20_24635 instead since it's TMOUS friendly. But to do so, I need to install a 2.07-2.12 radio and have not been able to do so - the process is stuck at 0%. What do I do?
What's worse, now the phone won't turn back on. It buzzes numerous times at the "stick together" screen and won't budge from it. I've already kinda dealt with it via a hard reset once, but all that does is get me back to the problem above. And just now it won't even let me hard-reset it - same buzzing and stuck at one screen...
highlanderfil said:
I've recently upgraded to the new official TMOUS ROM and now wanted to install OzROM_5.20_24635 instead since it's TMOUS friendly. But to do so, I need to install a 2.07-2.12 radio and have not been able to do so - the process is stuck at 0%. What do I do?
What's worse, now the phone won't turn back on. It buzzes numerous times at the "stick together" screen and won't budge from it. I've already kinda dealt with it via a hard reset once, but all that does is get me back to the problem above. And just now it won't even let me hard-reset it - same buzzing and stuck at one screen...
Click to expand...
Click to collapse
Way do you will change the radio? I mean radio 2.15.50.14 is working well!?
Secondly, I hope you didn't flash a x.XX.51.xx Radio!
No, it's a .50. I need to downgrade because that's what the instructions say.
you can't run a different radio on 3.14 roms because there is no hspl to allow you to flash just radios. the info regarding the required radio (as with much of the info here, its a continual work in progress and it would be impossible to keep up to date.) is from before the later radios were released. the radio you have will work.,
Problem is now my phone won't boot. Buzzes six times upon startup and nothing...
yea, dunno what to suggest forthat except if its under warranty swap it.
highlanderfil said:
Problem is now my phone won't boot. Buzzes six times upon startup and nothing...
Click to expand...
Click to collapse
Do you have hspl installed? You need that to flash unofficial roms. I think if you had it before and you flashed an official rom, you may have to hspl it again.
Sent from my HTC HD2 using XDA App
zarathustrax said:
Do you have hspl installed? You need that to flash unofficial roms. I think if you had it before and you flashed an official rom, you may have to hspl it again.
Sent from my HTC HD2 using XDA App
Click to expand...
Click to collapse
It's possible I don't...will look into that, thanks!