Hi,
I tried flashing my X7500's WM 6.0 to Mitchy's latest 6.5, but I later saw that I was installing a 3.5 SPL ROM to a 1.2 SPL (image ver 2.19.453.4). After the repair wizard told me to remove the battery for 3 seconds my device doesn't show the tricolor when in bootloader, but instead the screen is scrambled. After a while the screen turns to white.
Any of you guys out there have an idea on how I can fix it?
http://forum.xda-developers.com/showthread.php?t=405814
Related
Hi,
I had a WM6 Rom, pre-release, one of the Self Made available here ... I do not remember which one of the versions ...
I wanted to put the official WM6 rom, so this morning I downloaded and I tried to install it.
The installation started with my Tytn connected, the Tytn screen switched to HERM IPL-1.00 and the Red, Green, Blue, White Stripes ... and the installation continued.
Then I received a connection error from the Program ...
Now my Tytn is stuck on the "Stripes" Screen and even removing the battery and resetting ... the Stripes screen is always there ...
Any Clue ?
Thanks !
submaru said:
Hi,
I had a WM6 Rom, pre-release, one of the Self Made available here ... I do not remember which one of the versions ...
I wanted to put the official WM6 rom, so this morning I downloaded and I tried to install it.
The installation started with my Tytn connected, the Tytn screen switched to HERM IPL-1.00 and the Red, Green, Blue, White Stripes ... and the installation continued.
Then I received a connection error from the Program ...
Now my Tytn is stuck on the "Stripes" Screen and even removing the battery and resetting ... the Stripes screen is always there ...
Any Clue ?
Thanks !
Click to expand...
Click to collapse
Ok ... Classic noobing: do a search before posting ... I am looking at the "Help post for bricking" and trying the solutions, but I have to understand why bricked ...
I love this forum ...
Recovered my Tytn: I was in this case
SPL 1.01MFG
HTC_BOOT Any
Boot OS No
No GSM? No
KITL No
Diagnostic Solution: Stuck in bootloader after flash Mtty: "set 14 0" and "task 8" if doesn't help flash OS.nb again.
With those magic command, my Tytn restarted and booted !!!
Some more informations:
I have Rom WM 6.0 Custel 2.5 Version (ROM Date 04/17/07)
Radio Version 1.43.00.00
Protocol Version: 32.76.7020.19H
I tried to flash the Official HTC WM6 Italian, and you know the result ... What's worng ? Thanks
hi everyone, can someone please tell me what i did wrong.
I have flashed a few roms before and this time every time i start the 8125 it gets stuck cingular raising the bar screen.
The phone will still do hard reset.
Ipl 2.25.0001
Spl 2.2.5.001
Gsm 02.25.11
OS 11.0.1.1
I tried to do upgrade it to the the TNT 19199 professional wizard v.2. I used the shell tool and dropped the nk.nbf file into the shell folder like i have always done before and this time its stuck at the same screen. I can't connect it to active sync or even the computer to put back the stock cingular rom back in. Can someone please tell me what im doing wrong, from what i understand the phone is not bricked yet because i can still do a hard reset but still sends me back to the main startup screen. Help please.
Stock ROM can be flashed from Bootloader mode, just put your Wizard into bootloader mode (Camera+reset), then run the stock ROM RUU.
thanks helped out perfectly
Same Problem
New to this...Could someone Please give me a walkthrough on how to do this.I can still hard reset.I reset using camera + reset...Brings up r/b/g screen.I don't know how to flash from there.Any help is greatly appreciated.
IPL 2.25.0001
SPL 2.25.001
OS is 10.0.0.10
I took it back to WM5.Seems to be OK.Gonna try using Wizard Service Tool instead of ShellTool.See what happens
You should HardSPL, then use RUU on ROMs without IPL directly.
My first attempt to upgrade to AP4 did not succeed unfortunately (SPL to 3.50 upgrade went OK though), my power light stayed green and the display wouldn't come on.
So I took the Athena into bootloader and re-flashed back to AP3.
All seemed fine, the "Tap the screen to set up your device" screen appeared, I set it up and let the customization program run.
Unfortunately after the automatic reset at the end of the customization program, the device returned to the "Tap the screen to set up your device" and the customization program started again...
I tried interrupting the customization by soft resetting before it started executing itself, soft resetted during customization, let customization finish again (and again), but the device seems to be in an endless loop....
Any suggestions/help?
Thanks a lot in advance!
this happen because the spl and the kernel, AKA nk.exe, do not match. not sure what to do except try the new ap3 the cmonex posted **not sure if you tried that**
try the 3.0 cmonex posted and enjoy.
solved!
Thanks irus & Pawel062 (and cmonex!), that did the trick!
Probably not a bad idea to advise anybody who needs downgrading from AP4 to AP3 to use that rom. Download it from http://htc-hackers.com/uploads/ap3newspl.zip
See cmonex' thread at http://forum.xda-developers.com/showthread.php?t=386604
***great Information!***
HEY ALL,
I WAS ALSO HAVING SOME ISSUES VERY SIMILAR TO THESE WHILE TRYING TO "DOWNGRADE" TO ANY ROM FROM AP 4.0. THIS IS GREAT INFO AS I BUILD MY OWN ROMS CONSTANTLY, SO I WAS A BIT WORRIED WHEN I COULDNT SWITCH AFTER TRYING AP 4.O, BUT THANKS TO CMONEX, IRUS, & PAWEL062, WE CAN DOWNGRADE A BIT EASIER!
THANKS AGAIN!
M E G
I downloaded the http://htc-hackers.com/uploads/ap3newspl.zip
can anyone tell me the steps
note i'm stuck into the bootloader
mgozamy said:
I downloaded the http://htc-hackers.com/uploads/ap3newspl.zip
can anyone tell me the steps
note i'm stuck into the bootloader
Click to expand...
Click to collapse
just flash it with normal RUU
I have this problem of the "looping" with the customizations. My problem is that I can't get the device to a state where it is "talking" to activesync and from what I see, I need that to push this ap3spl new file.
When you say "just flash it with normal RUU" can you tell me what that means please? (sorry, noob here...) I've spent hours on the forums, wiki etc and I'm a bit lost.
I'm "trying" to get AP4 w/WM6.1 onto the device.
Purchased unlocked (new) and used on AT&T for 6 months.
Went to update the radio to 1.57 and used the unlocker first. (took out SIM/SD first of course).
Got past step one and then got a black screen on reboot...
I got AP3 to load but now I get this fun looping.. Setup device, load customizations, reboot, and start over.
Sounds like this file in this thread is my fix to at least get AP3 working but not sure how to apply. Can I do it from the bootloader?
thanks in advance for putting up with me
Oh yeah:
My current state:
ATHE100
IPL - v2.02
ATHE100 MFG
SPL -v3.50 OliNex
Eureka!
Ok, I'm not a COMPLETE noob.. (close). I'm up and running. AP3 (new spl) loaded, then loaded AP4. Woo Hoo!
No GPS
Well, I guess I'm "Almost" back up and running.
Since step three never got kicked off, it looks like my GPS rom/radio never was rewritten back to the device.
Any help on how to get just the GPS portion back?
Endless loop after flashing AP4
I have a similar problem. My Dopod U1000 was running WM6 and I upgraded to
radio version 1.58.00 no problem. After flashing AP4 I am in a cycle where my initial boot screen has black and white lines at the top and black at the bottom
Then get the Windows Mobile 6.1 screen and after automatic customizing the
PDA resets itself. I have tried to flash the AP3newspl file but it cant communicate successfully with the synced PDA. Any help?
Johnatara said:
I have a similar problem. My Dopod U1000 was running WM6 and I upgraded to
radio version 1.58.00 no problem. After flashing AP4 I am in a cycle where my initial boot screen has black and white lines at the top and black at the bottom
Then get the Windows Mobile 6.1 screen and after automatic customizing the
PDA resets itself. I have tried to flash the AP3newspl file but it cant communicate successfully with the synced PDA. Any help?
Click to expand...
Click to collapse
get into bootloader by pressing camera+reset and check your spl
you can flash a rom from here
also read this
http://forum.xda-developers.com/showthread.php?t=429013
Thanks lakeman. I reinstalled WM6 ROM from the boot loader.
My IPL v1.00 and SPL v1.20. Olipro and Radio 1.58
I have transferred enblerapi.cab to PDA and run it each time but when I flash
AP4 ROM or AP3newspl ROM I get an endless loop and my SPL stays v1.20
I cant seem to get a flash of SPL3.5 which I suspect is the problem.
Am I missing something?
Il download non funziona.
Hi,
i have a friends I-Mate JAMin (or HTC Prophet)
its a G4, now...it was running WM5, so i put HardSPL on it, went to flash a WM6.1 rom and now all it does is sit at the tri coloured screen, it seems like the HardSPL has done nothing, because the SPL is still the old numbers (the originals, it hasnt changed to 2.G4.4PDA, or whatever its suppose to show)....
I need help ASAP, i cant go back to my friend and tell him his phone is stuffed..
PLZ HELP, ANYONE....PLZ
hi,
did u try this
http://forum.xda-developers.com/showthread.php?t=353547
yep, tried that.
i actually cannot boot into a OS on the phone,
when it turns on it goes straight to the Tri-Coloured screen, i need some desperate help with this,
i have put HardSPL on there but the SPL version on the tri-coloured screen numbers have not updated to a new version,
i installed an update to the IPL version, so that has gone up to 2.20 or something like that.
the SPL number is currently 2.13.0001
i cannot get past the tri-coloured screen.
PLZ PLZ PLZ PLZ PLZ help, is the phone stuffed?
how do i fix it?
Dont Worry
If your scree show RUU and you see USB in the left corner when connecting USB - then dont worry.
Just fksh it with a NVID wm5 Prophet ROM that is available in this forum and tou will have your device back.. you can then try to upgrade it to WM6 etc
hi guys today i start updating my the rom on my x7500 i made it to the third step where there were a progres bar untill it goes 91% where it stuck for a while and the program infome me that there was an error and i had to take the usb off romove the battery for 3 seconds and then start the device and i do it but when i turn the phone on i recive a black screen with some white lins on the top and some red letters on the bottom and after 2 seconds i turn grey and the programm dident see the htc so it closed. can i fix it now and how thanksssss
note: that i can stiil get the red green blue wite screen by pressisng the camera button and resset so i start all over again untill the progress bar get to the 5 i think and it get me a messaga tha this programme cant used for this devise
Hi and welcome to the forum,
What does it say on the bootloader screen (Reset/ camera button) and which rom are you trying to load? sounds to me youre trying to load a rom with the wrong spl.
Regards
Jay
hi my friend and thanks for the response in the boot loader screen it says
IPL-V1.00
SPL-V1.20.OLIPRO
and i've try to to put the 13th of this list http://forum.xda-developers.com/showthread.php?t=397518 which is this one http://forum.xda-developers.com/showthread.php?t=411371
Hi,
Now im not sure still what rom it is you are trying to use, it would be better if you just gave me the name on the download link. So go through the start of downloading it again and copy the name of the link. I think you are trying to flash a SPL 3.5 rom onto an SPL 1.20 Athena (yours!). any how, do that and let me know. If you think you are going to use 6.5 roms that are around now then you will need to first flash with the AP 4.0 rom first, however you need to have a working rom on your athena first. so i would recomend you flash with AP 3.0 OR go back to a stock rom and start again. AP 4.0 swaps your SPL to 3.5, but it will swap back to SPL 1.2 if you want to.
Jay
thanks again my friend the broblem solved by following the steps on this link (the second post) http://forum.xda-developers.com/showthread.php?t=387454&highlight=mtty&page=4 but the broblem came becuse in the ist of roms says windows mobile 6.1 and spl 3.5 and spl 1.2 and inside the lin is says wm 6.5 and spl only 3.5 now i manage to put one but i will try to upgrate to spl 3.5 in order to get the rom i want one more time thanks responderman for the respone
Not a problem, glad you are sorted out now. Just be very careful if you upgrade to SPL 3.5, read the guide in full and follow it to the letter.
Regards
Jay
does someone knows how to update from spl 1.20 olipro to spl 3.5 on order to put an other rom for spl 3.5
follow instructions here
http://forum.xda-developers.com/showthread.php?t=429013