O2 Atom Problems: no service + can´t update ROM - iPAQ rw6828, XDA Atom Software Upgrading

Hi, my atom have 2 problems:
1: No service, so, cant use it as a phone, everithing is working, bluetooth, WiFi, etc, the sim is recognized by te phone, but cant find ´the network service.
So, my option is to upgrade the ROM:
Problem 2: once connected to Activesync (in Win Vista) start flashing a lot of rom´s and the phone change to "Upgrade Utility USB Connected" and the PC loose the connection, try to install another controller and the ROM soft send the message: can´t connect to the phone.
So, I cant upgrade or repair the rom.
DID ANYONE KNOWS THIS PROBLEMS?
Sorry for my english, I´m from Argentina.
THANKS

Related

I am in deep sh.., WM6 update screwed and bootloader does not work

Hi all.
I tried to update to WM6 on my Dopod 818 Pro with ProphetTouchIXbeta2. It displayed and error and after hard resetting I can only get the splash screen. So I roamed the forum the whole day downloaded a couple of other WM6 packages (I could not get the WM5 files from the WM6 upgrade guide, link is dead). So I downloaded the ROM updates from the HTC websites for the 818 Pro. I can start the 818 Pro into Bootloader, but whatever ROM file I use will tell me Update Error 260 Cannot connect!!
The Bootloader tells me the following: IPL 2.15.0001 / SPL 2.15.0001 and USB connected. Active Sync will not connect.
Sorry, I am a newbie and should have waited for the official upgrade. But I had to try
Thank you in advance for any help!
Cheers,
Markus
Hi,
i had the same trouble some time ago. The false was, that I connect my NEO on an USB Hub, take a direct connection between your PC and your XDA. Also, if it's possible, try another PC. HTH
Put your Prophet in bootloadermode: press Camm button and soft reset at the same time.
In ActiveSync on your PC: DISable connectionsetting "Allow USB connection"
Conect your Prophet to a USBport directly with a cable.
Run a NVID-RUU, perhaps the official VID-RUU doesn't recognize your device anymore.
This should do it.
i can confirm this process
Thanks guys, but the main issue is:
1. I can get into Bootloader
2. BUT ActiveSync does not make a connection with my DEvice in Bootloader and the ROMs I tried cannot connect to my device then.
I tried it on 2 machines (Vista and XP)
Cheers,
Markus
starkus said:
Thanks guys, but the main issue is:
1. I can get into Bootloader
2. BUT ActiveSync does not make a connection with my DEvice in Bootloader and the ROMs I tried cannot connect to my device then.
I tried it on 2 machines (Vista and XP)
Cheers,
Markus
Click to expand...
Click to collapse
Activesync is not supose to conect to phone in bootloder
just run the wm5
Thanks,
but if I run the WM5 by HTC its only goes to the Verify information screen and after that. it says Error [260]: Connection. The Update utility cannot connect to your PDA Phone.
And in the beginning of the process it displays a couple of steps, like check that your battery is at least 50% charged and other ssteps, of which one is, that I have to make sure that ActiveSyc is connected.
Cheers,
Markus
Solved
Ok, the issue was that only this file from HTC would do the update: RUU_Prophet_2151327_21513121_021921_DOP_ASIA_WWE_Ship.exe
Alle the others I downloaded would not work, also not the files I got from here. One was by the way full of Viruses !
Thanks for your help guys! Will try to get to WM6 again now
starkus said:
Ok, the issue was that only this file from HTC would do the update: RUU_Prophet_2151327_21513121_021921_DOP_ASIA_WWE_Ship.exe
Alle the others I downloaded would not work, also not the files I got from here. One was by the way full of Viruses !
Thanks for your help guys! Will try to get to WM6 again now
Click to expand...
Click to collapse
which one was "full of viruses" and how you checked it ?
Sorry should have mentioned it before:
It was Prophet"s_2.20.7.34_2.20.7114_02.69.21
Virus or unwanted program 'W32/Sality.L [W32/Sality.L]'
All .exes were infected in that package.
Cheers,
Markus

SPL flash failing

I'm following Mr Vanx's guide for upgrading my Jasjam from WM5 to WM6, but am having trouble with flashing the new bootloader onto the device. It's a second-hand telstra imate. I just bought it off ebay a couple of weeks ago and need to upgrade it to get it to read sdhc memory cards. I can't get it to connect to optus' (my mobile contract provider) mobile internet either, which I did via GPRS on my old phone. I'm hoping by upgrading the OS I can remove all of Telstra's code so It's not trying to connect to telstra's 3g network when I start the web browser.
When I get to the last step of the Hard-SPL installation, where the "updater will flash the new SPL and then restart your device (this will take generally less than a minute)" , the phone restarts almost immediately after clicking yes when prompted on the phone. The screen quickly goes to the bootloader screen, which says
"herm 100
IPL-SSPL by Des
Herm 100
SPL-1.09.ds"
The PC says that it can't connect to the phone and I should check the cable, which is still connected
The phone stays on the bootloader screen until I hit the soft reset, and WM5 boots like normal.
Has anyone else had this happen?
Yup,
Same problem over here. I had the problem before. But i fixed it! The only question is how did i do that? short term memory.
I'm trying to solve the problem. If its solved i will let you know.
Till then hang on
I've been trying again today. Still getting the same result, though I figured out if I just leave it when it gets to the bootloader screen, the pc I'm installing from eventually comes up with Error 260.
I'm thinking now that the XP firewall may be the issue, but I'm having trouble disabling it because it's managed by "group policies" (it's a work computer). I'm going to try either finding out which port to unblock, or starting the pc in safe mode so I can disable the firewall altogether.
I fixed the problem with the following softwaretool Hypercore. Just intergrate the Hard spl from olipro. After this the error dissapears.

upgraded wm6 rom is not connect internet via bluetooth and usb

hai
i i upgraded my atom executive but unfortunatley (n.touch,and absusla new rom wm6.1 is not able to connect net via bluetooth and usb says "failure of modem" i tried 100 times kindly look after this problem solve as early as possible i like your n touch and new rom wm6.1 but again installed official rom

Tytn as a modem: big problem with Schap's 3.54..Help needed!!

Hi all!
I'm new on the forum but it is quite a long time I read it. I'm italian.
I followed the guides to Hrd Spl and I upgraded my vodafone 1605 to WM6 using the Schap's rom 3.54 ITA and everythying is working fine. I have only one problem: when I had the original WM5 vodafone rom I was able to connect to internet using my Tytn as a modem as follows: programs>wireless modem>start.
Now, with the new rom I'm not able to connect to internet using the tytn as a modem but just by itself. When I connect my Dash using the USB cable, select the Internet Sharing option under Settings, it creates this "Windows mobile Internet sharing device" but this not allows mr to surf with my Laptop.
What can I do to solve this problem? I have tio downgrade again to WM5 or there is a possibility to solve this problem? Please let me know! Thank you so much
Have you tried...
After flashing your phone were you able to browse the web using the phones internet browser. If not then you are probably missing the data connection settings for your phone, once they are in place then the phone as modem/internet sharing option should work again. If you don't have those settings for your cellular carrier then you could always flash their rom back to the phone, lookup the settings, and then flash Schaps ROM again and input the network settings.
Good luck,
Sam

USB loses connection.....cannot upgrade.

Hello, i'm trying to upgrade my device but facing a weird problem. The WMDC works fine and i can sync my device. When i run the RUU, it analyzes the rom and put the device in bootloader mode....
as soon as the device enters the bootloader, the usb loses the connection and says "cannot recognize the device" or "drivers not found" etc....and the RUU gives the error of "cannot connect to the device. make sure...."
I have tried this with the AthenaUnlocker as well as the AthenaWrapper. I'm currently on SPL 1.1 and want to upgrade to 1.2
Please help!
I have the same problem!
I want to install HSPL on my device. I cannot install this via SD Card so i tried it with USB. But after the bootloader the connenction was lost. Many times...
Can somebody tell me how to fix this problem?
Thanks
Edet: My device is a HTC HD2
This might not fit your problem, but ...
... try to connect your device to a PC/laptop with USB 1.1 - with my Ameo I have many "connection loss" problems with USB 2.0 speed, which occure only on heavy (data) load on syncing.
Disabling USB2.0 is possible on some machines within the BIOS.
If you got no PC/laptop with USB1.1 you can disable the USB 2.0 related driver in the Windows Device Manager (it works for me, in general). Therefor open the device manager and select the "View" menu -> devices by connection (or similar). Now search for the Athena entry attached to the listed USB hardware. Disable the "most-upper" USB controller the Athena is attached to.
OK, the last description might be confusing, but try.
Good luck (as this solution fits to your problem, as I am not sure)
What worked for me
junooni said:
Hello, i'm trying to upgrade my device but facing a weird problem. The WMDC works fine and i can sync my device. When i run the RUU, it analyzes the rom and put the device in bootloader mode....
as soon as the device enters the bootloader, the usb loses the connection and says "cannot recognize the device" or "drivers not found" etc....and the RUU gives the error of "cannot connect to the device. make sure...."
I have tried this with the AthenaUnlocker as well as the AthenaWrapper. I'm currently on SPL 1.1 and want to upgrade to 1.2
Please help!
Click to expand...
Click to collapse
I just spent the weekend trying to unlock my Athena and was having the exact same problem... USB would disconnect, errors 202, 267 . I finally was able to flash the Olipro bootloader, but had a hard time unlocking the radio. My device showed no radio under its properties, so I could not tell what radio version I had. Pressing "phone" would not bring the dialup screen. After so much sweat, I had to put it apart, only to find that the radio board connection to the motherboard was improperly seated, thus was having a bad connection. Once the connection was properly seated, the phone booted up to the emergency call screen, notified that there was no SIM card detected and when I looked in the device properties, the radio version was listed!. I then proceeded to unlock and flash the radio and this time the connection was not lost, the process completed without a glitch.
Hope that helps...

Categories

Resources