hi ,green screen with horizontal lines came up with missing gsm line on my prophet while flashing with wm6.5 21234 ,then i tried to put gsm file and it stopped at boot screen tricolor one so i returned back to nvid wm5 which flashed it till 95% and gave an error at 100% and rebooted to tricolor again where i clicked on ruug4 file in update hardspl folder and after this it made reboot to wm5 (but wifi didn't work) so i gave it hardspl in updatehardspl folder and later flashed it with wm6.5 but wifi doesn't work and 1st splash screen is ok but second splash screen never shows up (instead green horizontal lines with ipl spl gsm and os come up and later 3rd splash screen comes up) wifi is not working in wm5 or wm6.5 with comm manager or quickmenu either.
has wifi hardware got spoilt ?(is there anyway to test it or correct it)
i have flashed to wm5 to wm6.5 twice to make sure i wasn't doing anything wrong.
also i tried alot of splash screen files but second splash screen remains those horizontal green lines only.
green lines liook like this http://www.dragoncub.net/htc/mda/boot.jpg
wifi is important to work.(green lines are acceptable unless they are interlinked with wifi)
kamalneet said:
hi ,green screen with horizontal lines came up with missing gsm line on my prophet while flashing with wm6.5 21234 ,then i tried to put gsm file and it stopped at boot screen tricolor one so i returned back to nvid wm5 which flashed it till 95% and gave an error at 100% and rebooted to tricolor again where i clicked on ruug4 file in update hardspl folder and after this it made reboot to wm5 (but wifi didn't work) so i gave it hardspl in updatehardspl folder and later flashed it with wm6.5 but wifi doesn't work and 1st splash screen is ok but second splash screen never shows up (instead green horizontal lines with ipl spl gsm and os come up and later 3rd splash screen comes up) wifi is not working in wm5 or wm6.5 with comm manager or quickmenu either.
has wifi hardware got spoilt ?(is there anyway to test it or correct it)
i have flashed to wm5 to wm6.5 twice to make sure i wasn't doing anything wrong.
also i tried alot of splash screen files but second splash screen remains those horizontal green lines only.
green lines liook like this http://www.dragoncub.net/htc/mda/boot.jpg
wifi is important to work.(green lines are acceptable unless they are interlinked with wifi)
Click to expand...
Click to collapse
1. It sounds like the disk partition was being disturbed with a fault address,
2. you are lucky that your Prophet is still alive,
3. try this official rom upgrade from dopod (uploaded ) (WM5, may be useful... , it won't brick you device for at least )
dioxda2 said:
1. It sounds like the disk partition was being disturbed with a fault address,
2. you are lucky that your Prophet is still alive,
3. try this official rom upgrade from dopod (uploaded ) (WM5, may be useful... , it won't brick you device for at least )
Click to expand...
Click to collapse
thanx mine is imate jamin G4 so would it be right to put in this dopod rom and is it G4 ,i also have original imate jamin rom which usually doesn't run because i made all these wm6.5 changes.
also battery is being used very fast now unlike before.
Edit:yours gave error when i put jamin original it stuck up at 100 % i rebooted to tricolor and the clicked on ruug4 in hardspl folder and then again rebooted to wm5 for 3rd time this time. and no wifi ...then wm6.5 and no wifi .
i guess wifi hard ware and second splashscreen area got spoilt .
Edit battery is ok but wifi is not .
Related
--------------------------------------------------------------------------------
mine is a G4 device IPL 2.09 SPL 2.09.0000
i flashed several times my prophet with diferent wm6 roms but i allways downgrade to wm5, cause some issues i didn't like,
this morning i tried to upgrade to wm6 again, made the procedure
1 Hard reset
2 connect to pc and wait to activesync to come up
3 run upgrade utility and wm5 flash started
after a while the upgrading process stucked at 5% and gave an error, i don't remeber whitch it was,
but since then my prophet always turns on in bootloader mode, you can do nothing, even turn it off, the only way to turn it off is removing the battery,
when you put the battery again and press power on it starts in bootloader mode
the diference that i notice it's that now the bootloader shows
IPL 2.09 and SPL 2.09 not anymore SPL 2.09.0000
so i tried again to flash the prophet but it always give me this errors
300 when i used the wm5 spanish rom
and 274 conection problem when i use the temp pdaviet rom or the fantastic mobiz rom
when i plug the prophet to the pc the bootloader displayes USB but activesync never starts
what could be my problem i used the correct G4 roms
please somebody help me
joesa said:
--------------------------------------------------------------------------------
mine is a G4 device IPL 2.09 SPL 2.09.0000
i flashed several times my prophet with diferent wm6 roms but i allways downgrade to wm5, cause some issues i didn't like,
this morning i tried to upgrade to wm6 again, made the procedure
1 Hard reset
2 connect to pc and wait to activesync to come up
3 run upgrade utility and wm5 flash started
after a while the upgrading process stucked at 5% and gave an error, i don't remeber whitch it was,
but since then my prophet always turns on in bootloader mode, you can do nothing, even turn it off, the only way to turn it off is removing the battery,
when you put the battery again and press power on it starts in bootloader mode
the diference that i notice it's that now the bootloader shows
IPL 2.09 and SPL 2.09 not anymore SPL 2.09.0000
so i tried again to flash the prophet but it always give me this errors
300 when i used the wm5 spanish rom
and 274 conection problem when i use the temp pdaviet rom or the fantastic mobiz rom
when i plug the prophet to the pc the bootloader displayes USB but activesync never starts
what could be my problem i used the correct G4 roms
please somebody help me
Click to expand...
Click to collapse
Don't know for sure that it will help, but when you want to connect to your PC in USB mode (bootloader) you should first disable "Allow USB CONNECTION" in the conections settingpanel of Active Sync.
thanks i'll give it a try
joesa said:
--------------------------------------------------------------------------------
mine is a G4 device IPL 2.09 SPL 2.09.0000
i flashed several times my prophet with diferent wm6 roms but i allways downgrade to wm5, cause some issues i didn't like,
this morning i tried to upgrade to wm6 again, made the procedure
1 Hard reset
2 connect to pc and wait to activesync to come up
3 run upgrade utility and wm5 flash started
after a while the upgrading process stucked at 5% and gave an error, i don't remeber whitch it was,
but since then my prophet always turns on in bootloader mode, you can do nothing, even turn it off, the only way to turn it off is removing the battery,
when you put the battery again and press power on it starts in bootloader mode
the diference that i notice it's that now the bootloader shows
IPL 2.09 and SPL 2.09 not anymore SPL 2.09.0000
so i tried again to flash the prophet but it always give me this errors
300 when i used the wm5 spanish rom
and 274 conection problem when i use the temp pdaviet rom or the fantastic mobiz rom
when i plug the prophet to the pc the bootloader displayes USB but activesync never starts
what could be my problem i used the correct G4 roms
please somebody help me
Click to expand...
Click to collapse
Try to search the new ROM update utility and try to reflash using it.
pda is dead
hey friends..!!
i have a problem with my neo..
got new update of wm 6. 4..0.0.0.1 version..
phone gets switched off by itself.. sometimes..
when sms comes or i recieve a call..
i fear it has become a black brick..
plz help me out..!!
and..
one more thing..
is there any was to restore my contact.. i had a backup in wm 5..
the back up file when restored in w m 6..
contacts don t open.. then again i hjave to hard reset it..
lost my contacts and documents.. but i stii have that back up file..
plz help me out..
replies awaited..!!
dj00912 said:
hey friends..!!
i have a problem with my neo..
got new update of wm 6. 4..0.0.0.1 version..
phone gets switched off by itself.. sometimes..
when sms comes or i recieve a call..
i fear it has become a black brick..
plz help me out..!!
and..
one more thing..
is there any was to restore my contact.. i had a backup in wm 5..
the back up file when restored in w m 6..
contacts don t open.. then again i hjave to hard reset it..
lost my contacts and documents.. but i stii have that back up file..
plz help me out..
replies awaited..!!
Click to expand...
Click to collapse
For the WM6, try Gullum V6 Touch...
Now for the contacts problem - flash WM5 back, restore your contacts and back up them with PIM backup 2.5 (use search you will find it in the forum somewhere).After reflashing the WM6 you will be able to restore them again. The other option is to use Outlook to synchronize.
chavdar said:
For the WM6, try Gullum V6 Touch...
Now for the contacts problem - flash WM5 back, restore your contacts and back up them with PIM backup 2.5 (use search you will find it in the forum somewhere).After reflashing the WM6 you will be able to restore them again. The other option is to use Outlook to synchronize.
Click to expand...
Click to collapse
It's beter NOT to use any backup software when you migrate from WM5 to WM6 or the other way around. Sync first with your desktop ans sync back after upgrading. The standard location are not the same, so it is messy when you replace the files to their original positions.
Hi,
I had a WM6 Rom, pre-release, one of the Self Made available here ... I do not remember which one of the versions ...
I wanted to put the official WM6 rom, so this morning I downloaded and I tried to install it.
The installation started with my Tytn connected, the Tytn screen switched to HERM IPL-1.00 and the Red, Green, Blue, White Stripes ... and the installation continued.
Then I received a connection error from the Program ...
Now my Tytn is stuck on the "Stripes" Screen and even removing the battery and resetting ... the Stripes screen is always there ...
Any Clue ?
Thanks !
submaru said:
Hi,
I had a WM6 Rom, pre-release, one of the Self Made available here ... I do not remember which one of the versions ...
I wanted to put the official WM6 rom, so this morning I downloaded and I tried to install it.
The installation started with my Tytn connected, the Tytn screen switched to HERM IPL-1.00 and the Red, Green, Blue, White Stripes ... and the installation continued.
Then I received a connection error from the Program ...
Now my Tytn is stuck on the "Stripes" Screen and even removing the battery and resetting ... the Stripes screen is always there ...
Any Clue ?
Thanks !
Click to expand...
Click to collapse
Ok ... Classic noobing: do a search before posting ... I am looking at the "Help post for bricking" and trying the solutions, but I have to understand why bricked ...
I love this forum ...
Recovered my Tytn: I was in this case
SPL 1.01MFG
HTC_BOOT Any
Boot OS No
No GSM? No
KITL No
Diagnostic Solution: Stuck in bootloader after flash Mtty: "set 14 0" and "task 8" if doesn't help flash OS.nb again.
With those magic command, my Tytn restarted and booted !!!
Some more informations:
I have Rom WM 6.0 Custel 2.5 Version (ROM Date 04/17/07)
Radio Version 1.43.00.00
Protocol Version: 32.76.7020.19H
I tried to flash the Official HTC WM6 Italian, and you know the result ... What's worng ? Thanks
My first attempt to upgrade to AP4 did not succeed unfortunately (SPL to 3.50 upgrade went OK though), my power light stayed green and the display wouldn't come on.
So I took the Athena into bootloader and re-flashed back to AP3.
All seemed fine, the "Tap the screen to set up your device" screen appeared, I set it up and let the customization program run.
Unfortunately after the automatic reset at the end of the customization program, the device returned to the "Tap the screen to set up your device" and the customization program started again...
I tried interrupting the customization by soft resetting before it started executing itself, soft resetted during customization, let customization finish again (and again), but the device seems to be in an endless loop....
Any suggestions/help?
Thanks a lot in advance!
this happen because the spl and the kernel, AKA nk.exe, do not match. not sure what to do except try the new ap3 the cmonex posted **not sure if you tried that**
try the 3.0 cmonex posted and enjoy.
solved!
Thanks irus & Pawel062 (and cmonex!), that did the trick!
Probably not a bad idea to advise anybody who needs downgrading from AP4 to AP3 to use that rom. Download it from http://htc-hackers.com/uploads/ap3newspl.zip
See cmonex' thread at http://forum.xda-developers.com/showthread.php?t=386604
***great Information!***
HEY ALL,
I WAS ALSO HAVING SOME ISSUES VERY SIMILAR TO THESE WHILE TRYING TO "DOWNGRADE" TO ANY ROM FROM AP 4.0. THIS IS GREAT INFO AS I BUILD MY OWN ROMS CONSTANTLY, SO I WAS A BIT WORRIED WHEN I COULDNT SWITCH AFTER TRYING AP 4.O, BUT THANKS TO CMONEX, IRUS, & PAWEL062, WE CAN DOWNGRADE A BIT EASIER!
THANKS AGAIN!
M E G
I downloaded the http://htc-hackers.com/uploads/ap3newspl.zip
can anyone tell me the steps
note i'm stuck into the bootloader
mgozamy said:
I downloaded the http://htc-hackers.com/uploads/ap3newspl.zip
can anyone tell me the steps
note i'm stuck into the bootloader
Click to expand...
Click to collapse
just flash it with normal RUU
I have this problem of the "looping" with the customizations. My problem is that I can't get the device to a state where it is "talking" to activesync and from what I see, I need that to push this ap3spl new file.
When you say "just flash it with normal RUU" can you tell me what that means please? (sorry, noob here...) I've spent hours on the forums, wiki etc and I'm a bit lost.
I'm "trying" to get AP4 w/WM6.1 onto the device.
Purchased unlocked (new) and used on AT&T for 6 months.
Went to update the radio to 1.57 and used the unlocker first. (took out SIM/SD first of course).
Got past step one and then got a black screen on reboot...
I got AP3 to load but now I get this fun looping.. Setup device, load customizations, reboot, and start over.
Sounds like this file in this thread is my fix to at least get AP3 working but not sure how to apply. Can I do it from the bootloader?
thanks in advance for putting up with me
Oh yeah:
My current state:
ATHE100
IPL - v2.02
ATHE100 MFG
SPL -v3.50 OliNex
Eureka!
Ok, I'm not a COMPLETE noob.. (close). I'm up and running. AP3 (new spl) loaded, then loaded AP4. Woo Hoo!
No GPS
Well, I guess I'm "Almost" back up and running.
Since step three never got kicked off, it looks like my GPS rom/radio never was rewritten back to the device.
Any help on how to get just the GPS portion back?
Endless loop after flashing AP4
I have a similar problem. My Dopod U1000 was running WM6 and I upgraded to
radio version 1.58.00 no problem. After flashing AP4 I am in a cycle where my initial boot screen has black and white lines at the top and black at the bottom
Then get the Windows Mobile 6.1 screen and after automatic customizing the
PDA resets itself. I have tried to flash the AP3newspl file but it cant communicate successfully with the synced PDA. Any help?
Johnatara said:
I have a similar problem. My Dopod U1000 was running WM6 and I upgraded to
radio version 1.58.00 no problem. After flashing AP4 I am in a cycle where my initial boot screen has black and white lines at the top and black at the bottom
Then get the Windows Mobile 6.1 screen and after automatic customizing the
PDA resets itself. I have tried to flash the AP3newspl file but it cant communicate successfully with the synced PDA. Any help?
Click to expand...
Click to collapse
get into bootloader by pressing camera+reset and check your spl
you can flash a rom from here
also read this
http://forum.xda-developers.com/showthread.php?t=429013
Thanks lakeman. I reinstalled WM6 ROM from the boot loader.
My IPL v1.00 and SPL v1.20. Olipro and Radio 1.58
I have transferred enblerapi.cab to PDA and run it each time but when I flash
AP4 ROM or AP3newspl ROM I get an endless loop and my SPL stays v1.20
I cant seem to get a flash of SPL3.5 which I suspect is the problem.
Am I missing something?
Il download non funziona.
hi guys today i start updating my the rom on my x7500 i made it to the third step where there were a progres bar untill it goes 91% where it stuck for a while and the program infome me that there was an error and i had to take the usb off romove the battery for 3 seconds and then start the device and i do it but when i turn the phone on i recive a black screen with some white lins on the top and some red letters on the bottom and after 2 seconds i turn grey and the programm dident see the htc so it closed. can i fix it now and how thanksssss
note: that i can stiil get the red green blue wite screen by pressisng the camera button and resset so i start all over again untill the progress bar get to the 5 i think and it get me a messaga tha this programme cant used for this devise
Hi and welcome to the forum,
What does it say on the bootloader screen (Reset/ camera button) and which rom are you trying to load? sounds to me youre trying to load a rom with the wrong spl.
Regards
Jay
hi my friend and thanks for the response in the boot loader screen it says
IPL-V1.00
SPL-V1.20.OLIPRO
and i've try to to put the 13th of this list http://forum.xda-developers.com/showthread.php?t=397518 which is this one http://forum.xda-developers.com/showthread.php?t=411371
Hi,
Now im not sure still what rom it is you are trying to use, it would be better if you just gave me the name on the download link. So go through the start of downloading it again and copy the name of the link. I think you are trying to flash a SPL 3.5 rom onto an SPL 1.20 Athena (yours!). any how, do that and let me know. If you think you are going to use 6.5 roms that are around now then you will need to first flash with the AP 4.0 rom first, however you need to have a working rom on your athena first. so i would recomend you flash with AP 3.0 OR go back to a stock rom and start again. AP 4.0 swaps your SPL to 3.5, but it will swap back to SPL 1.2 if you want to.
Jay
thanks again my friend the broblem solved by following the steps on this link (the second post) http://forum.xda-developers.com/showthread.php?t=387454&highlight=mtty&page=4 but the broblem came becuse in the ist of roms says windows mobile 6.1 and spl 3.5 and spl 1.2 and inside the lin is says wm 6.5 and spl only 3.5 now i manage to put one but i will try to upgrate to spl 3.5 in order to get the rom i want one more time thanks responderman for the respone
Not a problem, glad you are sorted out now. Just be very careful if you upgrade to SPL 3.5, read the guide in full and follow it to the letter.
Regards
Jay
does someone knows how to update from spl 1.20 olipro to spl 3.5 on order to put an other rom for spl 3.5
follow instructions here
http://forum.xda-developers.com/showthread.php?t=429013
Hi everyone.
I tried to upgrade my i-mate Jamin to WM 6.5 using this file.
I think I did everything right (I checked the G4 and HardSPL in the beginning of installation and I'm sure my MB is G4).
Everything was going perfect and the installation advanced without any problems, but at the end my Jamin was stuck in the three color screen, showing only the following words:
IPL: 2.13.001
SPL: 2.13.001
I tried to hold the Comm Manager and Soft Reset buttons as this topic recommends, but the phone gets back to the 3 color screen again, and no success...
I tried to pull out and reinsert the battery, also no success...
Please help me, this is my friend's phone! I AM SO NERVOUS and I may kill somebody!
Is there anything I can do to get rid of the 3 color screen?
mahi58 said:
Hi everyone.
I tried to upgrade my i-mate Jamin to WM 6.5 using this file.
I think I did everything right (I checked the G4 and HardSPL in the beginning of installation and I'm sure my MB is G4).
Everything was going perfect and the installation advanced without any problems, but at the end my Jamin was stuck in the three color screen, showing only the following words:
IPL: 2.13.001
SPL: 2.13.001
I tried to hold the Comm Manager and Soft Reset buttons as this topic recommends, but the phone gets back to the 3 color screen again, and no success...
I tried to pull out and reinsert the battery, also no success...
Please help me, this is my friend's phone! I AM SO NERVOUS and I may kill somebody!
Is there anything I can do to get rid of the 3 color screen?
Click to expand...
Click to collapse
Please don't panic! If you see when connect the phone to the computer and USB message on the bottom of prophet screen update is posible. So try to put original WM5 on the phone. Read dioxda2 post for more. For sure you don't hardspl your phone before flashing....
Thanks
bikertibi said:
Please don't panic! If you see when connect the phone to the computer and USB message on the bottom of prophet screen update is posible. So try to put original WM5 on the phone. Read dioxda2 post for more. For sure you don't hardspl your phone before flashing....
Click to expand...
Click to collapse
Thank you very much, my problem solved using the WM5 flashing process.
I thought it's impossible to get the phone connected to PC because activesync wasn't establishing a connection to the phone, but obviously I was wrong.
After flashing WM5, I performed a HSPL on the phone, and then used the file again, and the phone was upgraded to WM 6.5 with no problem.
I previously had downloaded your 6.5 ROM from a crappy forum, which was only including a download link and some useless info, and since I was a newbie myself D), I didn't even know that I should have performed a HSPL before upgrading the OS.