Related
Hi there,
I tried upgrading my HTC TyTN to the latest rom from South Africa available on this forum: RUU_HERMES_HTC_WWE_1[1].35.255.2_1.35.255.102_1.08.00.10_SHIP.
After 3% upgrading it said the progress failed and it needed to repair something. Then it told me to remove the battery for 3 secs, and put it back in. It comes back to the bootloader and stucks here.
When I try to upgrade over again, it says Vender ID error. It stays at the bootloader no matter what I do, and it keeps saying Vender ID error...
Any help please?
Thanks in advance!
Dennis
Do you have bootloader 1.04?
bootloader
It says IPL 1.01 and SPL 1.09...
its DEFINATLY a HTC TyTN yer?
HTC TyTN
Yes it is.
I think its time to ask a Hermes Guru.....anyone??
Im guessing it might involve manually flashing a ROM using the command line over USB?!?
Relax dude the guys on here will sort it.
Read here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
If you can't solve, post here:
http://forum.xda-developers.com/showthread.php?t=286755
Closing this thread.
please anyone in here help me for my x01ht
1. i flash with HER_DopodAsia_AUS_1[1].30.707.4_1.20.31.10_WWE_Ship.exe
2. when it flash until 14% , it stop
3. i plug out cable and restart phone , now phone only can go into bootloader mode
4. in bootloader mode , it show
HERM IPL-1.01
HERM SPL-1.06
5. now i flash whatever file into this phone , it will show invalid vender id
6. please teach me how to do now all master
thanks !
file i try to flash
-RUU_X01HT_1.33.761.4_1.14.00.10.exe
-RUU_Hermes_DopodAsia_AUS_1.30.707.8_1.27.30.10_WWE_SHIP.exe
-HER_DopodAsia_1237074_1060010_WWE_SHIP.exe
all not work , will show invalid vender id
check the two stickies in this forum - bricked device and free unlocker. If you can run the unlocker, it will SuperCID your phone, if you can get that far.
If not, check out the bricked device thread - lot's going on in there.
Also, have you tried putting the ROM back on that was there to start with? Inalid Vendor ID is a failed check by the phone to match Phone CID with ROM CID. If you didn't fry it out, then you whould be able to put the OLD ROM back on. If so, you have a little more work ahead of you.
no unlocker not work for me , please teach me step by step what should i do ... thanks for your help
hanyean1 said:
no unlocker not work for me , please teach me step by step what should i do ... thanks for your help
Click to expand...
Click to collapse
Shamelessly stolen from one of pof's recent posts but still applicable...
10 READ(wiki)
20 READ(Hermes->forums->stickies)
30 READ(Hermes->forums)
40 IF (Questions?) GOTO 10
50 FLASH(Hermes)
LOL
Closing this thread as he already posted here:
http://forum.xda-developers.com/showthread.php?t=286755
He Guys,
Just my luck I have bought an HTC Tytn with the original Dutch rom and sim unlocked second hand.
I wanted to put a new Dutch rom from HTC on it but I keep on getting the ERROR [244] : INVALID MODEL ID but what I don`t understand is I have used the original Dutch rom from HTC. So I checked the device information and under the tab identity it says;
Model No.: H
Platform: PocketPC
IMEI: xxxxxxxxxxxxxxxxxxx
Shouldn’t the Model No. be HERM200?
Has anyone any suggestions in how I can solve this problem so I can flash any rom I wish.
I have tried al the cid unlock programs I could find and in bootloader it says;
H
IPL-1.01
H
SPL-1.40.Olipro
Thanks in advanced.
Use RAR to unpack the Original Dutch ROM.
Take the NBH file that you get when you unpack the ROM.
Put it in a folder with CUSTOM_RUU from Olipro.
Run CUSTOM_RUU and it will load up the ROM from the NBH file, bypassing the CID check. Should work
Thanks for the reply,
I have tried what you suggested but I still get ERROR [244] : INVALID MODEL ID I have also read these posts http://forum.xda-developers.com/showthread.php?t=322231&highlight=CUSTOM_RUU+from+Olipro and http://forum.xda-developers.com/showthread.php?t=322119&highlight=CUSTOM_RUU+from+Olipro and http://forum.xda-developers.com/showthread.php?t=309707&highlight=CUSTOM_RUU+from+Olipro and tried these suggestions but every time I get the error message. The radio update process was the same for me it will go to 7% and then give the message ERROR [244] : INVALID MODEL ID.
I have also tried the HTC_Hermes_SIM_CID_Unlock_v3a and Hard-SPL-V7 but still get the error message.
I hope I’m doing something wrong if not then I hope you have a new suggestion.
Thanks in advance.
Please set your device in BOOTLOADER MODE and post here your IPL / SPL versions.
Junner2003 said:
Please set your device in BOOTLOADER MODE and post here your IPL / SPL versions.
Click to expand...
Click to collapse
Did you read first post?
VivaErBetis said:
Did you read first post?
Click to expand...
Click to collapse
Ups, missed the bottom - thought it is the signature already! Sorry, haven't had my coffee yet!
Well, looks like the device is CID unlocked!
How about trying to flash an entire cooked ROM?
i would suggest the following:
flash a cooked rom (any)
see if that makes any difference to your model id
then try and flash the native dutch rom
good luck
Hi Guys,
As you suggested I tried a cooked rom the Hermes_WM6_vanilla still get the same error message when I put my device manually in boot loader it shows;
H
IPL-1.01
H
SPL-1.40.Olipro
But as soon as I try an official or cooked rom it shows;
H
IPL-SSPL by des
H
SPL-1.09.ds
I’m now trying Schaps_WM6Pro_WWE_4.00_Full_Beta3.exe and choose for auto detect and it said 1.40 Olipro and in boot loader it shows;
H
IPL-1.01
H
SPL-1.40.Olipro
And after 1% I got the ERROR [244] : INVALID MODEL ID message again.
I think my options are getting slim.
Your ModelID is stored on NAND and can be edited quite trivially (mostly).
how it got corrupted I don't know, however, the important question is; can you get into the OS?
He Olipro,
The device it zelf works perfect I can go anywhere I want even in the OS.
Just lead the way.
Changing Model ID
I have a similar problem in that my Model ID got corrupted during a radio upgrade. I now get the same error (244) and am stuck on SPL2.10 and can't downgrade to fix it. Can anyone tell us how to manually change the model ID in the NAND?
Much appreciated.
Dumping NAND
Ok, I'm a relative newbie so appologies before I get flamed. Thanks Olipro for giving me a clue.
I have now got spl 2.60 on my device but am unsure how to dump the NAND. I've worked out how to dump the 3 partitions from the device to dump the OS but am still unclear which part of the device is the NAND. I've read the Wiki on the memory map but am still not too sure.
Anyone able to give me simple instructions to dump the NAND and once I've done that where abouts is the ModelID stored? Do I do this using mtty?
Thanks in advance.
http://forum.xda-developers.com/showthread.php?t=322225
NAND Dump
Thanks Drummer for pointing me in the right direction.
Ive done this bit:
BTW, if you want to do a full backup of you FULL eeprom nand at any time, connect as before and type these commands:
plink HERMES > full.nb (hit ENTER twice)
task 32 (hit ENTER once and only once from now on after every command)
password 0000000000000000 - My device password is BsaD5SeoA which I used instead.
set 1e 1
rbmc me.txt 50000000 7fff800
watch your file grow to 128 MB.
It creates a full.nb file but it stays at 1k!!
** Note I have copied the bootloader file for spl 2.60 on my Hermes and ran that so I can now use that versino instead of the 2.10 thats on my device if that makes a difference and have tried with no joy with either version. Yes I know it says to use 2.30 but I can't work out how to get that on my device due to the ModelID error.
The Model number is contained within the herm1.nb file that was posted by BusStop in that thread. No need for complete NAND reflashing, only that section. You'll see it using a Hex Editor. You should write down your WiFi MAC addess, so you can edit it before flashing the file with the corrected Model number. Now you just have to figure out how to get SPL 1.01 MFG on your device...
Thanks Drummer. I did try flashing the herm1.nb file but of course as I do not have SPL 1.01 MFG it gievs an error. I'll keep trawling through the site and see if I can work out how to get SPL 1.01 onto my device. I'm not going to let this damn device beat me.
Ok so I worked out how to get the ModelID using getdevicedata. Used nbhtool to create a vaild nbh using the ModelID I'd just got and used the spl from 2.30 and it updated that fine.
Excellent.
However did the same with the MFG1.01 and flashed it and......
I now have a dead brick, no power and no response form usb. Time to get a replacement device.
Thanks for all the help I've had. I'm sure it should have worked.
1.) Remove battery
2.) Connect Hermes to charger or USB
3.) Insert the battery while Hermes is connected to charger
4.) Red light should turn Amber
5.) Soft Reset
Thanks for the advice Drummer however:
1.) Remove battery
2.) Connect Hermes to charger or USB
3.) Insert the battery while Hermes is connected to charger
4.) Red light should turn Amber - Nope red light goes out!
Mne shows HHHHHHH
Hi all, i've upgraded my radio and after my model id changed to H.
So, reading some posts i've used NBHTOOL.
1.I've decompiled an original Italian ROM
2.i've obtained a custom nbh selecting only OS and EXTROM and changing my Model number.
3. after that i've flashed the nbh resulting into a write error at 84% and a bricked htc.
Luckily i was able to reflash roms and i processed to second experiment.
I've made a custom rom with only the os, and it WORKED!
so my questions are:
1. can i use my htc even if my external rom isn't flashed (it cames from an old Schaps 4.0 succesful flash)
2. It is safe to proceed installing bootloader SPL using the nbhtool like i did with the os?
In that case i will be able to fix the model id problem by flashinh spl 1.01 and using the wireless fixing method you posted..
Thanks in advance for your reply!
Hi
From my understanding the Ext rom is mainly used for carriers to install there specific addons and customizations so it shouldn't be a problem.
As you can see I did flash spl 2.30 using this method and it worked fine ti was only when something whent wrong flashing 1.01 that my problem happened but I think that may be that I used an nbs file instead of an nb file from what I've read since.
Good luck.
Edit: Just noticed someone on this thread has managed it by going straight ot 2.60 http://forum.xda-developers.com/showthread.php?t=322225
Please read this post first http://forum.xda-developers.com/showthread.php?t=339961 I`m hoping someone can give me instructions in how i can do this so I can change or upgrade my rom.
Thanks in advanced
http://forum.xda-developers.com/showthread.php?t=322225
Download the herm1.nb file in that thread and flash it to your device using the instructrutions on page one.
http://forum.xda-developers.com/attachment.php?attachmentid=46888&d=1186868649. It uses Hermes 200.
If you want to edit it to a different Device ID, use a HEX Editor and edit bytes 4008-400D.
Hi Drummer 10630,
I have red the thread and I have to start by downgrading my spl and that’s just the problem I cannot downgrade or upgrade to anything because I keep on getting the error message Invalid model Id.
Now I’m trying my best to understand what it all says in the thread but what’s easy for you guys is Chinese to me and I’m from Holland.
So could you explain to me in lames terms which action I should take first to get my model id name changed back into HERM200 in nand.
I’m sorry if I’m a pain in the ash………e but I can’t do this without your help.
It's all in the thread. Read Mr Vanx's downgrading SPL pages...then flash the nand.
Hey Drummer10630,
Like I said I cannot downgrade I have red the thread several times and the Mr Vanx's downgrading SPL pages, tried the hard spl v7 but still get the error message invalid model id.
As you can read in this thread http://forum.xda-developers.com/showthread.php?t=339961 if I go to boot loader using the OK and Power button I get
H
IPL-1.01
H
SPL-1.40.Olipro
But if I use the spl wrapper I get
H
IPL-SSPL by des
H
SPL-1.09.ds
Does this make any difference?
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeGuide
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
ERROR ?242 : INVALID LANGUAGE ERROR ?244 : INVALID MODEL ID ERROR ?294 : INVALID VENDER ID ERROR ?296 : UPGRADE ONLY
One of these error messages will appear when you use the wrong RUU to do the upgrade. RUU will check if the Model ID and Language ID are compatible with the device. Make sure you use the appropriate RUU tool to upgrade.
Hey Drummer10630,
I followed the instructions but it starts with installing HARD SPL which wont work because of the MODEL ID error so I skipped that and tried the rest and everything went fine I change the MODEL ID to H which is what it says on my device put the RUU_SIGNED.NBH file in the HTC rom folder and fired it up and guess what MODEL ID error.
I think what I need to do is to change my MODEL ID in nand like Olipro says.
Olipro said:
Your ModelID is stored on NAND and can be edited quite trivially (mostly).
how it got corrupted I don't know, however, the important question is; can you get into the OS?
Click to expand...
Click to collapse
device id
Hove the imei is related to the device id ?
There is relations ?
I mind part of the imei is the device id ?
Regards
i have ATHENA 100 in T-MOBILE Ameo........ i update lot of rom's on my ameo with success . my phone status is: IPL-v1.00 SPL-v1.20. Olipro.
my bad luck i try to update with that rom (Athena_SPL3.5_WM6.1_WWE_R6.1-Michy) after 92% rom got error & phone restart. after that my Ameo hang on startup. i put my phone into usb mode by pressing CAMERA key + POWER & try to upgrade with lot of diffrent roms but i got ERROR[244] INVALID MODEL ID (pic attached below) plz help me how can i update my phone in working condition??>......................
kanwalgee said:
i have ATHENA 100 in T-MOBILE Ameo........ i update lot of rom's on my ameo with success . my phone status is: IPL-v1.00 SPL-v1.20. Olipro.
my bad luck i try to update with that rom (Athena_SPL3.5_WM6.1_WWE_R6.1-Michy) after 92% rom got error & phone restart. after that my Ameo hang on startup. i put my phone into usb mode by pressing CAMERA key + POWER & try to upgrade with lot of diffrent roms but i got ERROR[244] INVALID MODEL ID (pic attached below) plz help me how can i update my phone in working condition??>......................
Click to expand...
Click to collapse
Plenty of people have done this before !
There is a sticky thread in this forum above your post
http://forum.xda-developers.com/showthread.php?t=405814
Whoops Sorry Jay, I didn't realise that kanwalgee had double posted
same answer anyway.