Related
Ok...I have been through all the posts about upgrading etc. I still have a problem and I'm sure that I'm overlooking something....but I can't figure it out on my own. Here is what is happening (it does the same thing with every RUU that I've used...the DST fix...upgrading to WM6....etc)
1. I run the RUU and let it go through its routine (extract files, verify info on pc, etc.)
2. I check the box that says I have read the readme and click next
3. The next screen appears and it has the following steps:
Connect to the USB cable (check)
Establish an ActiveSync Connection (check)
Disable standby and hibernation on PC (check)
Make sure batter is > 50% (check)
Then I check the box and click next
4. I pick the update and click on the update button
5. I verify that I want to upgrade my phone from ROM verion x.xx.xxx to x.xx.xxx and click next
6. The program tells me that I am finally ready to update...and if I am sure I want to proceed to click next...so I click next
7. As soon as I click next...the progress bar comes up on my pc and my phone goes into standby mode (no bootloader...just standby). The progress bar never moves.
8. After a minute or two the RUU give me the ERROR [260]: Connection
9. I reboot my device and repeat steps 1-8
10. I reboot my device and my computer and repeat steps 1 - 8.
Now if I leave my device connected to the usb and close out the RUU after it gives me the ERROR [260], and then run the RUU again...when it is first verifying the information on my pc (before it asks any questions and before it tells me to connect my device) it will throw the device into bootloader mode. If I try to keep running the RUU while the device is in bootloader mode it give me the error that my device is not connected. I have tried and tried...maybe one of ya'll can help me. Thanks in advance
Chris
Some questions:
.) Is your desktop PC running XP or Vista?
If you have a firewall running, close it.
.) If you running Vista check this guide:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=23&Itemid=27
.) What updates did you try to flash?
.) Did you install Olipros bootloader first?
gerald_s said:
Some questions:
.) Is your desktop PC running XP or Vista?
If you have a firewall running, close it.
.) If you running Vista check this guide:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=23&Itemid=27
.) What updates did you try to flash?
.) Did you install Olipros bootloader first?
Click to expand...
Click to collapse
XP
No firewall
I tried to flash the WM6 from AT&T I assume its beta
and no did not install the Olipros bootloader
Ok...I think I found out how to do this...Ya'll can tell me if I'm screwing something up.
I go through all the steps listed above until it gets to the progress screen. When it gets there I manually put the the device in bootloader mode (Power, side ok, and reset). Once I do this...the progress bar starts moving. I will let you know if this works...
Hmmmm
Its not the way it should work but if it works its ok
You should have installed Olipros HardSPL first and then try to flash an official rom. If its working then something with your download is wrong.
What ROM is on there now?
Has the phone been CID unlocked?
Oli's CustomRUU is better, you may want to unpack the ROM and put the NBH in a folder with Oli's RUU and then do the upgrade.
BTW, gerald_s is right, you should not have to do that... what you may want to do is put the phone in Bootloader mode manually (while not connected to the PC), then plug in the USB, then start the RUU. That helps some people with 260 error.
I've got the same damn issue... it's driving me crazy. I had this occur when I flashed my Hermes100 from the stock version to Custel's. After about 15 starts and reboots it took. I'm now trying to get to Vp3G's 3.60 and it continues to give me the 260 error.
I am trying to figure out how to fomat my micro, but really hoping to find a solution over cable.
Hermes 100
IPL 1.04
SPL - 2.10 Olipro
Any suggestions?
You may be trying to flash a rom that includes the radio rom. What is your device? Is it possible that your device is a new x01ht with radio 1.14 and radio bootloader 0182? If yes, then you will get this error when you try to flash a rom with this method because during the flash it will be disconnected by the radio bootloader because it is not overwriteable. If you flash using the NBH file on the microSD, it will skip past radio and radio boot and just flash the other parts of the file.
mikebraeuer said:
I've got the same damn issue... it's driving me crazy. I had this occur when I flashed my Hermes100 from the stock version to Custel's. After about 15 starts and reboots it took. I'm now trying to get to Vp3G's 3.60 and it continues to give me the 260 error.
I am trying to figure out how to fomat my micro, but really hoping to find a solution over cable.
Hermes 100
IPL 1.04
SPL - 2.10 Olipro
Any suggestions?
Click to expand...
Click to collapse
If you are running windows XP, just connect the card to the computer, open MY COMPUTER, right-click the removable disk that is your microSD and then click format. Default in windows xp is to format using FAT32 filesystem which is perfect.
The thing is... if you dont know how to format a drive in Windows, should you be flashing your device yourself?
Which Solution???
I've got a Softbank X01HT with:
S/N: HT639
SuperCID <--- result of checking by mtty
IPL: 1.04
SPL: 2.10Olipro
GSM: 1.47.00.10
OS: 3.54.07 WWE
I tried to flash with new Schap 3.54c but the process would not be done coz ERROR 262 or ERROR 302. Fortunately, after failure of flashing, my device is still normal running. Then I tried to flash radio 1.51.00.10 but I got the same above. Once again, I have just tried to flash splash screen and I got the same result too. It mean my device can not upgrade anything !
Anybody here show me a solution that help my device to become a normal device, I mean it will be able to flash anything ROM as it would be! Don't tell me READ and READ, I had read so much . And don't tell me use MTTY again SPL1.01MFG, I think that is a final solution
Wantoknow said:
I've got a Softbank X01HT with:
S/N: HT639
SuperCID <--- result of checking by mtty
IPL: 1.04
SPL: 2.10Olipro
GSM: 1.47.00.10
OS: 3.54.07 WWE
I tried to flash with new Schap 3.54c but the process would not be done coz ERROR 262 or ERROR 302. Fortunately, after failure of flashing, my device is still normal running. Then I tried to flash radio 1.51.00.10 but I got the same above. Once again, I have just tried to flash splash screen and I got the same result too. It mean my device can not upgrade anything !
Anybody here show me a solution that help my device to become a normal device, I mean it will be able to flash anything ROM as it would be! Don't tell me READ and READ, I had read so much . And don't tell me use MTTY again SPL1.01MFG, I think that is a final solution
Click to expand...
Click to collapse
Have you tried flashing with your microSD?
Kevbodian said:
Have you tried flashing with your microSD?
Click to expand...
Click to collapse
I forgot to tell that, I had flashed through extra memory card yet, and could be done!
But I wanna flash ROM against CustomRUU through MS Active Sync as I had used before. Can you help me
i have a problem very similar to Chris. when i check the box "yes activesync is syncronised", and then the progressbar shows up and the phone goes into standby.
i've turned standby of in powermanagement options.
my os is XP
i use active sync v4.5
and this is first time i try this.
i've read something about this bootloader, i can get there but then i cannot sync with active sync. so i kinda stuck.
have been searching the forums and this was the same problem as mine but i don't understand your solutions.
//KufrA
--Problem solved--
i did all things without activesync,
1. start phone in bootloader
2. do the install
3. wait 0% to 100%, and done.
is there a problem with active sync or why do i have to do anything with it at all?
hello
I'm having a problem with my Wizard.
I was with a rom and slowed, and began to slow in bootscreen.
I spent Wizardlove no use, no use WM5 original.
my wizard is not with the spl olip.
this spl and IPL 2.22.0001
bootloader and in turn makes sound that connects, most do not connect the hardspl nor softspl, only the ruu connects.
what do I do?
Thank you
sorry for English
Which windows is running on your pc,if its Vista,there are still problems while flashing on Vista,WinXP is recommended.
Get the phone in Bootloaders and connect with pc,when small usb appears,run the RUU in the rom,only try to flash official stock rom,well you can also try to flash wizard_love rom.Hope it'll flash.Activesync doesn't work and connect in Bootloaders,so stop worrying if it doesn't connect,its not required during rom flash.hardSPL or SoftSPL also do not work in Bootloaders,it must have a working OS and connection through Activesync.Get the battery fully charged before flashing,many communication problems are due to weak battery,and take out,if any sdcard or Minisd card in the phone before flashing.
most already put the wizard love and still hangs in bootscreen
help me ;/
Download official stock rom of your carrier,get the phone in Bootloaders,Hook up the phone with pc via usb cable,check if small usb appear at the bottom of the Bootloaders ,if its there,then its establishing connection.Run the RUU in the rom,it'll start to flash,but if there's no usb present in the Bootloaders,then there's a connection problem.Either the usb cable is faulty or the mini usb port of the phone is broken.
already tried by several Ronse, original qtek, and wizard love economies do not seem to advance not always hangs at the exchange bootscreen wizard love always
EDIT ON JULY 5, 2010:
AFTER 30 TRYES on 2 days my pda has only enter bootloader mode on two times... and when I connected to my pc didnt appear "USB" on screen.
any help will be grateful. Please. Thanks.
EDIT ON JULY 2, 2010:
MY PDA DOESNT START THE BOOTLOADER
I have make HSPL 1.42 with "success" because "we hacked it " appeared on screen BUT...
that has been the las thing that I have seen on the screen. Now I cannot switch on, neither start in bootloader, and when I connect to pc and I turn on normally the pda in my pc I can see like "new hardware found... qualcomm..." (while on PDA is black screen).
I have try to left the HD2 without battery during seconds, minutes and hours before try again.
I have try to left the HD2 charging all night before try again.
I have try with other batteries (I have 3).
I have try with different with windows 7 and windows XP (for looking what happens if I connect HD2 with black screen.
ANY HELP????
MY PDA DOESNT START THE BOOTLOADER
on JULY 1 I SAID:
(Sorry for my bad english) I have been for 2 complete days trying to solve before post this new thread. Now, the explanation:
I have a Spanish Movistar company HD2.
To enter in bootloader mode I have to be a few seconds (or minutes, it depends...) without battery. When I get into bootloader mode I see:
_______________
PB81100 HX-BC
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
Serial
_______________
So I supose that it isn´t the HSPL installed.
Sometimes when I simply switch on I see HTC logo with white background (I supose that is because it has the task29 made.
When I left the device without battery few seconds (or minutes) and I get into again and I switch on I see too the HTC logo with white background.
I have try to flash some roms through microSD card and the result is allways the same: It changes the screen into a grey and I see "Loading..." but it stays like this infinitely (I have try to wait more than 20 minutes). I have try this with original Movistar Company ROM, original HTC ROM, some radios (more than 6 types), some coocked ROMS (including arthemis, BSB beast, Energy), and the result is allways the same, stays "Loading..."
I have try to flash through PC. CustomRUU Recognizes the device but when it starts to update the device doesnt change screen or sometimes looks like pixelated screen, and on the PC appears like new hardware found (qualcomm CDMA Technologies MSM) and update through pc doesnt start. I have try too when It appears like new hardware found to remove the battery and start on bootloader mode, but update neither starts.
I have try to make HSPL (2 and 3) and the result is allways the same: recognizes the device and on bootload screen apears "USB" in the white part. HSPL tells me what SPL I have ( 2.08.0000|| ) and let me choose 2.08.HSPL BUUUUT when I push continue in the device nothing happens, on the PC appears like new hardware found (qualcomm CDMA Technologies MSM) and HSPL gives me an error (sometimes one sometimes other):
__________________
CRITICAL ERROR
Flow: 00000006
Error code : 00000010
Description: Unknown
__________________
or
__________________
CRITICAL ERROR
Flow:00000002
Error code: 00000003
Description: USB Operation failed
__________________
Thanks to all for your help.
Tryed installing a radio higer then 2.6? Phone wont start without 2.7 or higer
Nakazul said:
Tryed installing a radio higer then 2.6? Phone wont start without 2.7 or higer
Click to expand...
Click to collapse
telling "some radios (more than 6)" I mean that I have try with more than 6 types of radios, but yes, I have try with radios from 2.04 to 2.08.
Thanks Nakazul
but first you need to hspl. you cant flash any of those roms or radios without hspl
enter bootloader (three coloured screen)
connect to USB, wait for 'serial' to become 'USB' - if pc tries to say it is a qualcomm, change USb ports. Use one around teh back of the PC, not one in the front casing.
run hspl ( 2 or 3, doesnt matter which) pick an spl that ends with .hspl, so
2.08.0000 - No, stock, it wont work
2.08.hspl - yes, now you can flash.
now run task 29 (use the shadrac repack)
enter bootloader again, confirm that your spl says 2.08.hspl
flash your rom over USB. Do not use sd card (using sd card is probably how you got spl 2.08.0000 on a non tmous phone)
samsamuel said:
but first you need to hspl. you cant flash any of those roms or radios without hspl
enter bootloader (three coloured screen)
connect to USB, wait for 'serial' to become 'USB' - if pc tries to say it is a qualcomm, change USb ports. Use one around teh back of the PC, not one in the front casing.
run hspl ( 2 or 3, doesnt matter which) pick an spl that ends with .hspl, so
2.08.0000 - No, stock, it wont work
2.08.hspl - yes, now you can flash.
now run task 29 (use the shadrac repack)
enter bootloader again, confirm that your spl says 2.08.hspl
flash your rom over USB. Do not use sd card (using sd card is probably how you got spl 2.08.0000 on a non tmous phone)
Click to expand...
Click to collapse
First, thanks.
I connect to USB, "serial" become to "USB" like allways (qualdcomm hardware never appears when conected with bootloader without start the HSPL or CustomRUU). I start HSPL 2 and I choose "2.08.hspl" like allways. I push continue and PC tells me "new hardware, qualcomm...." (allways on that momment, when push "continue" after choose "2.08.hspl") I change the USB cable to another port and automatically HSPL gives me an error and I only can acept and the HSPL software closes. I have try to change USB port before push "acept" but nothing. Allways appears "new hardware, qualcomm..." con PC while PDA stays with bootloader screen apearing like connected through USB.
Hope you understand all, I really dont know how to explain better.
strange. Is it the stock usb cable?
I think you should try a different pc.
samsamuel said:
strange. Is it the stock usb cable?
I think you should try a different pc.
Click to expand...
Click to collapse
I have try on 2 pc-s. One cpu with windows 7, the other with windows XP.
I have another HTC HD2 (this of Vodafone) and the cable works perfectly. (The died HD2 isnt mine of a friend.)
PD: Shouldn´t it be able to load correctly the stock rom through microSD?
Thanks!
sorry, i dont know what to suggest next. I'll sleep on it and let you know if anything occurs to me.
Thoughts for now, , your original stock rom is probably failing because i 'think' stock spl 2.x will not allow itself to be downgraded to 1.x A few people got stuck before hspl2 arrived.
How about trying a goldcard, with the tmous 2.13 stock rom? that would change the spl to 2.10.0000 and you could try with hspl3, , it could be that the spl is messed up (you shouldn't have been flashing with sd card, it messes with the spl/hspl, even when the flash fails, hspl will still be removed)
have you allowed the qualcomm dirbvers to install when in bootloader mode?
when in bootloader the AMSS is taking over connection so its the snapdraon drivers that your pc is trying to install, which are the ocrrect ones.
Allow your computer to install them, and try it again
g.lewarne said:
have you allowed the qualcomm dirbvers to install when in bootloader mode?
when in bootloader the AMSS is taking over connection so its the snapdraon drivers that your pc is trying to install, which are the ocrrect ones.
Allow your computer to install them, and try it again
Click to expand...
Click to collapse
When I tried to install that driver I make click on continue but doesnt find drivers...
NEWS!!!!!! (bad news...)
I have downgrade into HSPL 1.42 with "we hacked it" on screen, but now cant start the bootloader mode!!!! I have been trying to be without battery during minutes and during hours!!
I cannot star PDA on bootloader mode with or without USB cable conected and with or without SD inside. BUUUT If I turn on the HD2 normally in my PC I can see "new hardware...qualcomm...". What can I do whith this?
Thanks to all for your help!
byAGM said:
When I tried to install that driver I make click on continue but doesnt find drivers...
NEWS!!!!!! (bad news...)
I have downgrade into HSPL 1.42 with "we hacked it" on screen, but now cant start the bootloader mode!!!! I have been trying to be without battery during minutes and during hours!!
Thanks to all for your help!
Click to expand...
Click to collapse
"cant start the bootloader mode" Why not?
Can you just do a reset by poking the reset button (button near battery) while holding volume down? That won't bring up the bootloader??
zkid2010 said:
"cant start the bootloader mode" Why not?
Can you just do a reset by poking the reset button (button near battery) while holding volume down? That won't bring up the bootloader??
Click to expand...
Click to collapse
I dont know why but... I´m during few minutes (I have try during hours too) without battery, I put the battery inside the PDA and I push power button while holding volume down (like allways I have done to enter bootload) and nothing happens. I try again with reset button and nothing.
On both ways the HD2 makes a short vibration but doesnt bring up the bootloader.
When I connect to PC and I turn on the pda normally, pushing the power button (whithout hold the volume down button) I can see on PC like "new hardware found... qualcomm....", but the PDA screen its black. (I have try to connect other HD2 and works perfectly on the same PC with the same cable).
Thanks to all.
FYNALLY AFTER "WE HACKED IT " TO HSPL 1.42 I CANNOT START THE PDA NEITHER THE BOOTLOADER.
I have try lefting the HD2 without battery for a seconds, minutes and more than 8 hours... I have try too with the reset button. Nothing happens, I only can ear the little vibration that allways make. Nothing more...
May be to exist any solution with that 3 pins that are between SIM and microSD card? any connection with them? I dont know...
Will be this the first died HD2?... hope that no... but...
ANY HELP??
THANKS.
I have been 2 days trying to turn on the pda on bootloader mode. I have been lefting without battery during hours before trying to turn on but I has turn on (on bootloader mode) only 2 times and fail when connect to pc.
.
Somebody knows why I cannot start my pda on bootloader (remember it hasn´t any rom inside) in except of 2 times by 30 tryes?
Thanks and sorry for my bad english.
HELP PLEASE, DEAD HD2, NO BOOTLOADER.
is it possible that the battery isnt charged now? my telstra hd2 is stuck on the white htc screen constantly and i know the battery died on it and thought the same as you..i took the battery out for about a halfhour then plug it in and left it for a day and i was back in business with a charge. may be worth trying mate
the-wrangler said:
is it possible that the battery isnt charged now? my telstra hd2 is stuck on the white htc screen constantly and i know the battery died on it and thought the same as you..i took the battery out for about a halfhour then plug it in and left it for a day and i was back in business with a charge. may be worth trying mate
Click to expand...
Click to collapse
I have one cradle for charging batteries and 3 batteries.
The 3 times that the PDA has enter to bootloader has been without being the battery at 100% (between 50% and 60%).
Thanks for your help, the wrangler.
byAGM said:
I have one cradle for charging batteries and 3 batteries.
The 3 times that the PDA has enter to bootloader has been without being the battery at 100% (between 50% and 60%).
Thanks for your help, the wrangler.
Click to expand...
Click to collapse
no prob mate, wish i couldve helped you. ill keep wrackin my brain and see if i think of anything that may help you
Hi All,
I've successully insttaled mmty and tried some commands. all the formating and info commands.
After 2-3 mins. later I got this error message.
errmsg_file.log :Flash NAND DM internal transfer failed: dmov_transfer() errmsg_file.log :bad-block check - error DM transfer failedDMOV dev 0 chan 7 transfer: invalid channel state: 20
I turned off the phone and removed the battery waited for 2 mins. and rum MTTy again.
the same commands worked.
but after 2-3 mins I run another silly command like info 1,2,3... same error messaged apperad on MTTY again.
by the way ;
there is a similar thread here :
http://ip208-100-42-21.static.xda-developers.com/showthread.php?t=718611&page=3
Hi, sorry for capitalized title...
I searched and tested for weeks for a solution in this helpful and very professional forum... but I still haven't found a trick for my problem:
I have a NIKI100 - 20key that ActiveSync doesn't recognize (usb port still charge in Windows environment but no data transmission seems to work).
I tried many PCs with many OS, and now I can say that THIS IS NOT A SOFTWARE PROBLEM (or not?).
So i tried SD flashing, and it works only with signed ROM, so I can't flash WM 6.5
Because of USB issue, I can't flash HardSPL.
MTTY doesn't find the NIKI on COM or USB port.
The question is:
Is there a way to flash HardSPL via SD or is there a signed ROM with WM 6.5??
THANKS A LOT IN ADVANCE!!!
ROM: 2.16.831.3
Radio: 1.65.29.22
NIKI100
SPL-1.22.0000
CPLD-4
Marshalll said:
Hi, sorry for capitalized title...
I searched and tested for weeks for a solution in this helpful and very professional forum... but I still haven't found a trick for my problem:
I have a NIKI100 - 20key that ActiveSync doesn't recognize (usb port still charge in Windows environment but no data transmission seems to work).
I tried many PCs with many OS, and now I can say that THIS IS NOT A SOFTWARE PROBLEM (or not?).
So i tried SD flashing, and it works only with signed ROM, so I can't flash WM 6.5
Because of USB issue, I can't flash HardSPL.
MTTY doesn't find the NIKI on COM or USB port.
The question is:
Is there a way to flash HardSPL via SD or is there a signed ROM with WM 6.5??
THANKS A LOT IN ADVANCE!!!
ROM: 2.16.831.3
Radio: 1.65.29.22
NIKI100
SPL-1.22.0000
CPLD-4
Click to expand...
Click to collapse
Can you tell me what happens when you connect your device with your computer, when it is already in bootloadermode.
You can turn the phone in bootloadermode to turn your device off and press then on/off button and camera button on the same time, and keep them pressed until bootloader appears.
If I'm correct you will see Serial in the white block, just let me know what you see in the white block when you connect the phone with the computer, if I'm correct Serial will change in Usb, if not just let me know.
Greetz,
Tnx for reply...
I see USB when I connect the cable, Serial when I disconnect the cable.
I'm searching for a SD-card-method for flashing HardSPL: is this a good idea or I'm just wondering ?
Marshalll said:
Tnx for reply...
I see USB when I connect the cable, Serial when I disconnect the cable.
I'm searching for a SD-card-method for flashing HardSPL: is this a good idea or I'm just wondering ?
Click to expand...
Click to collapse
Ok, can you tell me if you're device has a simlock ?
Greetz,
Hi.
No simlock.
Tnx.
Marshalll said:
Hi.
No simlock.
Tnx.
Click to expand...
Click to collapse
Ok thanks, I'll do some searching and see if we can fix it.
Regards,
Ok, if I where in your situation I should try it this way, just be aware that I can not test it because I don't have such a problem, and you can brick your device if it went wrong.
1. Copy sspl-1.16-nike.exe to your sd-card
2. Copy sspl-1.16-nike.exe from your sd-card to your device
3. Turn phone off and remove sim and sd-card
4. Turn phone on and connect device to your computer
5. Run sspl-1.16-nike.exe on your phone
6. Wait until usb appears in your device
7. Unplug and replug the usb cable
8. Now flash the HardSPL 1.22
If you can run the HardSPL you should be able to flash a wm 6.5 rom.
Rataplan said:
Ok, if I where in your situation I should try it this way, just be aware that I can not test it because I don't have such a problem, and you can brick your device if it went wrong.
1. Copy sspl-1.16-nike.exe to your sd-card
2. Copy sspl-1.16-nike.exe from your sd-card to your device
3. Turn phone off and remove sim and sd-card
4. Turn phone on and connect device to your computer
5. Run sspl-1.16-nike.exe on your phone
6. Wait until usb appears in your device
7. Unplug and replug the usb cable
8. Now flash the HardSPL 1.22
If you can run the HardSPL you should be able to flash a wm 6.5 rom.
Click to expand...
Click to collapse
All right from 1. to 7. but when I run flashin it shows error code 260 (unable to connect).
Is there a way to run SPL "JUMP" and then flash HardSPL via SD card? I think it's the only way to flash HardSPL
Rataplan is the expert one on this area,
but wath is your operating system? Seven or XP?
Because i just was able to hardspl on XP, all other things I was able to do on Seven.
Marshalll said:
All right from 1. to 7. but when I run flashin it shows error code 260 (unable to connect).
Is there a way to run SPL "JUMP" and then flash HardSPL via SD card? I think it's the only way to flash HardSPL
Click to expand...
Click to collapse
Did you try to run the HardSPL 1.22 from the bootloader ?
Let me explain a little bit better, did you connect your device with your computer when your device is in bootloadermode and then run the HardSPL 1.22
If this fails, you can rename your nbh-file, hardspl-1.22-nike-shipped.nbh into nikeimg.nbh, copy nikeimg.nbh into the root of your sd-card and turn your device on while pressing the on/off button and the camerabutton on the same time and follow the instructions on the screen.
Succes,
Rataplan said:
Did you try to run the HardSPL 1.22 from the bootloader ?
Let me explain a little bit better, did you connect your device with your computer when your device is in bootloadermode and then run the HardSPL 1.22
If this fails, you can rename your nbh-file, hardspl-1.22-nike-shipped.nbh into nikeimg.nbh, copy nikeimg.nbh into the root of your sd-card and turn your device on while pressing the on/off button and the camerabutton on the same time and follow the instructions on the screen.
Succes,
Click to expand...
Click to collapse
Yes, I tried all of this method...The PC can't recognize the niki in bootloader mode.
When I put HardSPL on a tested sd-card (renamed NIKEIMG.nbh), I'm stuck in white screen with "Loading...".
I found some method for flashing HardSPL via sd-card (for Kaiser: http://forum.xda-developers.com/showthread.php?t=433835):
is there a SSPL Jump for Niki that run from sd (as with Kaiser sd-method)?
BTW, I think this is the right way... I'm trying and searching!
For Openview:
I tried with many PCs with XP Pro and 7. The niki usb port seems to be broken (only charges, but no data connection).
Nothing seems to work. If anyone has somethig for flash SSPL and HardSPL from SD, please post!!!
Any other ideas???
I think we tried everything but unfortunally the answer is that it isn't possible to flash the hardspl via sd, the only person you can ask is cmonex, she is the only one who can set this straight.
Here is her User cp but she is a very busy lady.
If you fix it, plse post it in this thread it can help others.
Goodluck buddy
Ok I'll try to contact mrs. cmonex. Of course, I'll post any solution (hope to find one... ).
Tnx for all!
SOLVED!
I solved the issue!! It was only a hardware problem with HTC ExtUSB port!!!
I cleared the pin and resoldered the port on motherboard. Then I flashed HardSPL via standard method and now I can flash anything form sd-card!!
Thanks to all.
Mr. Rataplan, now we can close this post!
Thanks!!
Great Marshalll, I'll ask Electroz to close this thread.
Hi Guys^^
I'm quite new to all this flashing stuff and spent the last week trying to figure this out but it seems I'm missing something.
I've got a O2 xda star (niki300) phone with a 1.58.16.27 radio (i think) and spl 1.16. I wanted to install a new rom and choose the Salvy.C83 V3.3 3g 20 Keys since it seemed to be one of the newest(correct me if I'm wrong).
It says that hardspl and a 1.65 radio is needed so i downloaded hardspl1.22-nike-shipped and the official rom linked in the wiki where the 1.65 radio seems to be included.
-I connect my phone (without sim and sd)
-and run the Nike CustomRUU
-It's starts quite normal but when the progress bar is shown (at 0% to be exact) I get to hear the disconnecting and connecting sounds of windows and some moments later the setup is aborted because of connection issues.
This problem occurs everytime at the exact same moment so I guess it can't be a broken cable...
I'd be very glad if you could tell me what I'm doing wrong or at least share some ideas of what I could try with me
Thank you in advance
Merglasch said:
Hi Guys^^
I'm quite new to all this flashing stuff and spent the last week trying to figure this out but it seems I'm missing something.
I've got a O2 xda star (niki300) phone with a 1.58.16.27 radio (i think) and spl 1.16. I wanted to install a new rom and choose the Salvy.C83 V3.3 3g 20 Keys since it seemed to be one of the newest(correct me if I'm wrong).
It says that hardspl and a 1.65 radio is needed so i downloaded hardspl1.22-nike-shipped and the official rom linked in the wiki where the 1.65 radio seems to be included.
-I connect my phone (without sim and sd)
-and run the Nike CustomRUU
-It's starts quite normal but when the progress bar is shown (at 0% to be exact) I get to hear the disconnecting and connecting sounds of windows and some moments later the setup is aborted because of connection issues.
This problem occurs everytime at the exact same moment so I guess it can't be a broken cable...
I'd be very glad if you could tell me what I'm doing wrong or at least share some ideas of what I could try with me
Thank you in advance
Click to expand...
Click to collapse
you'd better try again to update the Hard SPL and use HardSPL v.1.15 ~ http://forum.xda-developers.com/showthread.php?t=355730
with hard SPL that you can flash any rom and make CID, Security Unlocker too
thanks for the answer but sadly it doesn't change a thing
I run this UpdateRomUtility from flash-uspl but it gives me the same connection error (i think it lost connection as the phone went into 4 color mode, but I could be wrong)
Or is there another way to install this?
are you sure have followed all the directions given jockyw ??
What OS are you using on your computer??
have you deactivated anti- virus program or firewall on the PC before doing the flash HardSPL ??
sorry not my intention to return to ask, but I want you to more thorough and more detailed in discussing a problem so that you succeed in overcoming
I'm using Windows 7 64 bit Professional
about the instructions, I tried two different ways:
1. Connect my switched on phone. Then run the RomupdateUtility from flash-uspl-niki. (gives the Connection issue)
2. Do the steps with the sspl first. I put the sspl in the root directory of my phone and execute it through my phone. It goes in color - mode then USB is written on the screen ->I unplug and replug my usb cable->nothing changes. Running the Romupdateutility doesn't work because it says it isn't connected.
windows firewall is switched off
will test again with antivir also deactivated
Merglasch said:
I'm using Windows 7 64 bit Professional
about the instructions, I tried two different ways:
1. Connect my switched on phone. Then run the RomupdateUtility from flash-uspl-niki. (gives the Connection issue)
2. Do the steps with the sspl first. I put the sspl in the root directory of my phone and execute it through my phone. It goes in color - mode then USB is written on the screen ->I unplug and replug my usb cable->nothing changes. Running the Romupdateutility doesn't work because it says it isn't connected.
windows firewall is switched off
will test again with antivir also deactivated
Click to expand...
Click to collapse
if your computer is running Win 7 64- bit, using WMDC 6.1 Driver for Windows Vista (64-bit) ~ http://www.microsoft.com/download/en/details.aspx?id=3182
thanks that worked^^
any advice about which rom and radio I should install?^^
Merglasch said:
thanks that worked^^
any advice about which rom and radio I should install?^^
Click to expand...
Click to collapse
You just try with Insomnia ROMs ~ http://forum.xda-developers.com/showthread.php?t=497347
Works like a charm^^
Thanks to your help I've got a much more enjoyable phone now
Thank you and
Have a nice day ^^