Hi Guys^^
I'm quite new to all this flashing stuff and spent the last week trying to figure this out but it seems I'm missing something.
I've got a O2 xda star (niki300) phone with a 1.58.16.27 radio (i think) and spl 1.16. I wanted to install a new rom and choose the Salvy.C83 V3.3 3g 20 Keys since it seemed to be one of the newest(correct me if I'm wrong).
It says that hardspl and a 1.65 radio is needed so i downloaded hardspl1.22-nike-shipped and the official rom linked in the wiki where the 1.65 radio seems to be included.
-I connect my phone (without sim and sd)
-and run the Nike CustomRUU
-It's starts quite normal but when the progress bar is shown (at 0% to be exact) I get to hear the disconnecting and connecting sounds of windows and some moments later the setup is aborted because of connection issues.
This problem occurs everytime at the exact same moment so I guess it can't be a broken cable...
I'd be very glad if you could tell me what I'm doing wrong or at least share some ideas of what I could try with me
Thank you in advance
Merglasch said:
Hi Guys^^
I'm quite new to all this flashing stuff and spent the last week trying to figure this out but it seems I'm missing something.
I've got a O2 xda star (niki300) phone with a 1.58.16.27 radio (i think) and spl 1.16. I wanted to install a new rom and choose the Salvy.C83 V3.3 3g 20 Keys since it seemed to be one of the newest(correct me if I'm wrong).
It says that hardspl and a 1.65 radio is needed so i downloaded hardspl1.22-nike-shipped and the official rom linked in the wiki where the 1.65 radio seems to be included.
-I connect my phone (without sim and sd)
-and run the Nike CustomRUU
-It's starts quite normal but when the progress bar is shown (at 0% to be exact) I get to hear the disconnecting and connecting sounds of windows and some moments later the setup is aborted because of connection issues.
This problem occurs everytime at the exact same moment so I guess it can't be a broken cable...
I'd be very glad if you could tell me what I'm doing wrong or at least share some ideas of what I could try with me
Thank you in advance
Click to expand...
Click to collapse
you'd better try again to update the Hard SPL and use HardSPL v.1.15 ~ http://forum.xda-developers.com/showthread.php?t=355730
with hard SPL that you can flash any rom and make CID, Security Unlocker too
thanks for the answer but sadly it doesn't change a thing
I run this UpdateRomUtility from flash-uspl but it gives me the same connection error (i think it lost connection as the phone went into 4 color mode, but I could be wrong)
Or is there another way to install this?
are you sure have followed all the directions given jockyw ??
What OS are you using on your computer??
have you deactivated anti- virus program or firewall on the PC before doing the flash HardSPL ??
sorry not my intention to return to ask, but I want you to more thorough and more detailed in discussing a problem so that you succeed in overcoming
I'm using Windows 7 64 bit Professional
about the instructions, I tried two different ways:
1. Connect my switched on phone. Then run the RomupdateUtility from flash-uspl-niki. (gives the Connection issue)
2. Do the steps with the sspl first. I put the sspl in the root directory of my phone and execute it through my phone. It goes in color - mode then USB is written on the screen ->I unplug and replug my usb cable->nothing changes. Running the Romupdateutility doesn't work because it says it isn't connected.
windows firewall is switched off
will test again with antivir also deactivated
Merglasch said:
I'm using Windows 7 64 bit Professional
about the instructions, I tried two different ways:
1. Connect my switched on phone. Then run the RomupdateUtility from flash-uspl-niki. (gives the Connection issue)
2. Do the steps with the sspl first. I put the sspl in the root directory of my phone and execute it through my phone. It goes in color - mode then USB is written on the screen ->I unplug and replug my usb cable->nothing changes. Running the Romupdateutility doesn't work because it says it isn't connected.
windows firewall is switched off
will test again with antivir also deactivated
Click to expand...
Click to collapse
if your computer is running Win 7 64- bit, using WMDC 6.1 Driver for Windows Vista (64-bit) ~ http://www.microsoft.com/download/en/details.aspx?id=3182
thanks that worked^^
any advice about which rom and radio I should install?^^
Merglasch said:
thanks that worked^^
any advice about which rom and radio I should install?^^
Click to expand...
Click to collapse
You just try with Insomnia ROMs ~ http://forum.xda-developers.com/showthread.php?t=497347
Works like a charm^^
Thanks to your help I've got a much more enjoyable phone now
Thank you and
Have a nice day ^^
Related
Ok, I've been trying to update my 8525 for hours...here is my problem. First, I tried to HardSPL-v7 but I kept getting an "Error [240] File open". I think this is preventing me from doing any ROM update. When I try to run the Cingular ROM update activesync shuts down and I get a connection error, I think it is "error [260]". I have wiped or cleaned out my 8525 so that I am back to day one. I have tried both ROM updates on 2 separate computers and I get same error messages on both computers. I have searched the Wiki's but have found nothing, so please help. As you can tell, I am a virgin to ROM updates so please go gently.
I should add, my present ver. ROM AKU 2.3 (1.34.502.7018.01H) SPL 1.06 IPL 1.01. Radio is 1.16.
have you taken a look at my Safe WM5 Upgrade Guide??
If you follow this guide EXACTLY, you should be fine.
mrvanx said:
have you taken a look at my Safe WM5 Upgrade Guide??
If you follow this guide EXACTLY, you should be fine.
Click to expand...
Click to collapse
I have, I have even tried the mtty "fix" but I had problems with that as well. I get a modem connection screen but there is nothing about a USB connection.
Bit more info would be nice, which ROM are downloading, and where from??
Also what procedure are you doing to update?? EXACT info please.
mrvanx said:
have you taken a look at my Safe WM5 Upgrade Guide??
If you follow this guide EXACTLY, you should be fine.
Click to expand...
Click to collapse
Ok, I just tried it 2 more times, Hard-SPL. It flashes to the 8525 and goes into bootloader and shows the following "HERM100 IPL-SSPL by Des HERM100 SPL-1.09.ds" at this point activesync 4.5 shuts down the 8525 is stuck in bootloader (it never reboots) and after a few minutes I get "Error [260] Upated Error". Hard SPL shuts down and the 8525 is stuck in bootloader mode. At this point I have been disconnecting the USB cable and doing a soft reset, once the phone is on, I go into bootloader and the old info shows up SPL 1.06 and IPL 1.01.
Let me have a think, firstly do you have the latest versions of the .net framework installed?
I was able to finally run HardSPLv7, I had to do it on another computer. Now, I would like to update to RUU_Hermes_CINGULAR_WWE_2.15.502.3_6275_1.40.30.00_108_Ship.exe. I assume I should use the same computer that I used to successfully run HardSPL. Do I need to rebuild the rom file with RUUWrapper.exe (CustomRUU by olipro) & Dutty's Good NBH Tool, before running the RUU_Hermes_CINGULAR_WWE_2.15.502.3_6275_1.40.30.00_108_Ship.exe update?
mrvanx said:
Let me have a think, firstly do you have the latest versions of the .net framework installed?
Click to expand...
Click to collapse
I have .Net 1 thru 3.5 (pre-release) installed on the computer that I can not get to run any ROM updates.
9
compudds said:
I was able to finally run HardSPLv7, I had to do it on another computer. Now, I would like to update to RUU_Hermes_CINGULAR_WWE_2.15.502.3_6275_1.40.30.00_108_Ship.exe. I assume I should use the same computer that I used to successfully run HardSPL. Do I need to rebuild the rom file with RUUWrapper.exe (CustomRUU by olipro) & Dutty's Good NBH Tool, before running the RUU_Hermes_CINGULAR_WWE_2.15.502.3_6275_1.40.30.00_108_Ship.exe update?
Click to expand...
Click to collapse
Yes if you carry on the guide past flashing hardspl you will get the radio updated aswell.
Can i ask, what is different on the computer you used???
mrvanx said:
Yes if you carry on the guide past flashing hardspl you will get the radio updated aswell.
Can i ask, what is different on the computer you used???
Click to expand...
Click to collapse
Off hand, the major difference would be Intel (worked) vs. AMD (failed) but I doubt that is the problem, you would be flooded with questions due to so many computers that have AMD chips. The USB cable was the same as well. I'll have to think about that...
Definatly check your "failed" computer is up to date with .net and everything else, most likely a software problem.
I have this problem as well..
AT&T 8525 windows moble 6 trying to install the hardspl v7.
v3.5 and 3.0 .net framework.
the RUUwrapper program gets to the 'verifiying info' screen then give me an erroe 240 message. 'the update utility can not open the requested file.'
any help would be great. Looking to add the touch it interface.
thanks,
Mike
Read the post Hard SPL at the top of this forum and go to page 116 ( I believe its post #1160) and use the sd card method. You don't need to use the pc at all. I generally flasah ALL os's using the sd card method as it seems to be safer then using the usb method. No "sync errors" to deal with.
Cheers...
I have the exact same problem..
When it goes to tri-color screen, the USB connection goes off and windows will pop up the search for driver dialogue box.. then afterward another dialogue box will appear saying Error [260].
I tried restarting my pc and device (even removing the battery) but still failure
Any help would be highly appreciated. Thanks.
blackphnx said:
I have the exact same problem..
When it goes to tri-color screen, the USB connection goes off and windows will pop up the search for driver dialogue box.. then afterward another dialogue box will appear saying Error [260].
I tried restarting my pc and device (even removing the battery) but still failure
Any help would be highly appreciated. Thanks.
Click to expand...
Click to collapse
I loaded it thru the sd card just as the post above suggested. It loaded the hardspl just fine. My PPC seems to run faster as well.
Thanks for the help! it is much appreciated.
blackphnx said:
I have the exact same problem..
When it goes to tri-color screen, the USB connection goes off and windows will pop up the search for driver dialogue box.. then afterward another dialogue box will appear saying Error [260].
I tried restarting my pc and device (even removing the battery) but still failure
Any help would be highly appreciated. Thanks.
Click to expand...
Click to collapse
One thing that i have learned from flashing my 8525 is to remove any USB device except the 8525. This has worked for me.
swimmy said:
One thing that i have learned from flashing my 8525 is to remove any USB device except the 8525. This has worked for me.
Click to expand...
Click to collapse
But my mouse is on USB. I might try on different computer and post back the results.
UPDATE
I tried using my friend's laptop and it installed without a problem. I think the issue is with the .NET framework. I installed the latest one before flashing and it worked fine. Hmmm.. Im not sure about this tho.
Hello.... Try the sd card method. You don't need the computer...
Sorry if I sound condescending, but, I seem to find a lot of people saying that they have sync problems. Solution, Take the pc out of the equation (except to load files onto sd card). It is SOOO much safer then using the pc, no "sync" problems, no chance of usb being disconnected, reset button being hit or , worst case scenario, power failure...
You have to either have little or no battery power or MANUALLY hit the reset button with the stylus to stop the flash...
And thats my 2 cents....
Refer to post #13 to find out how to use sd card method to flash hard spl...
Cheers...
sd card method???
how?
Ok...I have been through all the posts about upgrading etc. I still have a problem and I'm sure that I'm overlooking something....but I can't figure it out on my own. Here is what is happening (it does the same thing with every RUU that I've used...the DST fix...upgrading to WM6....etc)
1. I run the RUU and let it go through its routine (extract files, verify info on pc, etc.)
2. I check the box that says I have read the readme and click next
3. The next screen appears and it has the following steps:
Connect to the USB cable (check)
Establish an ActiveSync Connection (check)
Disable standby and hibernation on PC (check)
Make sure batter is > 50% (check)
Then I check the box and click next
4. I pick the update and click on the update button
5. I verify that I want to upgrade my phone from ROM verion x.xx.xxx to x.xx.xxx and click next
6. The program tells me that I am finally ready to update...and if I am sure I want to proceed to click next...so I click next
7. As soon as I click next...the progress bar comes up on my pc and my phone goes into standby mode (no bootloader...just standby). The progress bar never moves.
8. After a minute or two the RUU give me the ERROR [260]: Connection
9. I reboot my device and repeat steps 1-8
10. I reboot my device and my computer and repeat steps 1 - 8.
Now if I leave my device connected to the usb and close out the RUU after it gives me the ERROR [260], and then run the RUU again...when it is first verifying the information on my pc (before it asks any questions and before it tells me to connect my device) it will throw the device into bootloader mode. If I try to keep running the RUU while the device is in bootloader mode it give me the error that my device is not connected. I have tried and tried...maybe one of ya'll can help me. Thanks in advance
Chris
Some questions:
.) Is your desktop PC running XP or Vista?
If you have a firewall running, close it.
.) If you running Vista check this guide:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=23&Itemid=27
.) What updates did you try to flash?
.) Did you install Olipros bootloader first?
gerald_s said:
Some questions:
.) Is your desktop PC running XP or Vista?
If you have a firewall running, close it.
.) If you running Vista check this guide:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=23&Itemid=27
.) What updates did you try to flash?
.) Did you install Olipros bootloader first?
Click to expand...
Click to collapse
XP
No firewall
I tried to flash the WM6 from AT&T I assume its beta
and no did not install the Olipros bootloader
Ok...I think I found out how to do this...Ya'll can tell me if I'm screwing something up.
I go through all the steps listed above until it gets to the progress screen. When it gets there I manually put the the device in bootloader mode (Power, side ok, and reset). Once I do this...the progress bar starts moving. I will let you know if this works...
Hmmmm
Its not the way it should work but if it works its ok
You should have installed Olipros HardSPL first and then try to flash an official rom. If its working then something with your download is wrong.
What ROM is on there now?
Has the phone been CID unlocked?
Oli's CustomRUU is better, you may want to unpack the ROM and put the NBH in a folder with Oli's RUU and then do the upgrade.
BTW, gerald_s is right, you should not have to do that... what you may want to do is put the phone in Bootloader mode manually (while not connected to the PC), then plug in the USB, then start the RUU. That helps some people with 260 error.
I've got the same damn issue... it's driving me crazy. I had this occur when I flashed my Hermes100 from the stock version to Custel's. After about 15 starts and reboots it took. I'm now trying to get to Vp3G's 3.60 and it continues to give me the 260 error.
I am trying to figure out how to fomat my micro, but really hoping to find a solution over cable.
Hermes 100
IPL 1.04
SPL - 2.10 Olipro
Any suggestions?
You may be trying to flash a rom that includes the radio rom. What is your device? Is it possible that your device is a new x01ht with radio 1.14 and radio bootloader 0182? If yes, then you will get this error when you try to flash a rom with this method because during the flash it will be disconnected by the radio bootloader because it is not overwriteable. If you flash using the NBH file on the microSD, it will skip past radio and radio boot and just flash the other parts of the file.
mikebraeuer said:
I've got the same damn issue... it's driving me crazy. I had this occur when I flashed my Hermes100 from the stock version to Custel's. After about 15 starts and reboots it took. I'm now trying to get to Vp3G's 3.60 and it continues to give me the 260 error.
I am trying to figure out how to fomat my micro, but really hoping to find a solution over cable.
Hermes 100
IPL 1.04
SPL - 2.10 Olipro
Any suggestions?
Click to expand...
Click to collapse
If you are running windows XP, just connect the card to the computer, open MY COMPUTER, right-click the removable disk that is your microSD and then click format. Default in windows xp is to format using FAT32 filesystem which is perfect.
The thing is... if you dont know how to format a drive in Windows, should you be flashing your device yourself?
Which Solution???
I've got a Softbank X01HT with:
S/N: HT639
SuperCID <--- result of checking by mtty
IPL: 1.04
SPL: 2.10Olipro
GSM: 1.47.00.10
OS: 3.54.07 WWE
I tried to flash with new Schap 3.54c but the process would not be done coz ERROR 262 or ERROR 302. Fortunately, after failure of flashing, my device is still normal running. Then I tried to flash radio 1.51.00.10 but I got the same above. Once again, I have just tried to flash splash screen and I got the same result too. It mean my device can not upgrade anything !
Anybody here show me a solution that help my device to become a normal device, I mean it will be able to flash anything ROM as it would be! Don't tell me READ and READ, I had read so much . And don't tell me use MTTY again SPL1.01MFG, I think that is a final solution
Wantoknow said:
I've got a Softbank X01HT with:
S/N: HT639
SuperCID <--- result of checking by mtty
IPL: 1.04
SPL: 2.10Olipro
GSM: 1.47.00.10
OS: 3.54.07 WWE
I tried to flash with new Schap 3.54c but the process would not be done coz ERROR 262 or ERROR 302. Fortunately, after failure of flashing, my device is still normal running. Then I tried to flash radio 1.51.00.10 but I got the same above. Once again, I have just tried to flash splash screen and I got the same result too. It mean my device can not upgrade anything !
Anybody here show me a solution that help my device to become a normal device, I mean it will be able to flash anything ROM as it would be! Don't tell me READ and READ, I had read so much . And don't tell me use MTTY again SPL1.01MFG, I think that is a final solution
Click to expand...
Click to collapse
Have you tried flashing with your microSD?
Kevbodian said:
Have you tried flashing with your microSD?
Click to expand...
Click to collapse
I forgot to tell that, I had flashed through extra memory card yet, and could be done!
But I wanna flash ROM against CustomRUU through MS Active Sync as I had used before. Can you help me
i have a problem very similar to Chris. when i check the box "yes activesync is syncronised", and then the progressbar shows up and the phone goes into standby.
i've turned standby of in powermanagement options.
my os is XP
i use active sync v4.5
and this is first time i try this.
i've read something about this bootloader, i can get there but then i cannot sync with active sync. so i kinda stuck.
have been searching the forums and this was the same problem as mine but i don't understand your solutions.
//KufrA
--Problem solved--
i did all things without activesync,
1. start phone in bootloader
2. do the install
3. wait 0% to 100%, and done.
is there a problem with active sync or why do i have to do anything with it at all?
Help please!
I have an T-Mobile Ameo (also known Athena X7500) and i tried the Olipro Unlocker, but the installation didnt finish, at 59% stopped. After that i turn off the device, then turn on, but my device still have a 4 colour screen,red, green, blue and white, it doesnt boot the Windows Mobile, just have the installation screen...
please help
Use olipro's tool again and then flash your final ROM
i tried it many times, but since than my Athena X7500 was dead, the Olipros unlocker doesnt work. The program said: "The Update Utility cannot connect your PDA phone"
In bootloader (coloured screen), does it say anything? if so what? when you try to flash a rom or use unlocker do you get a code? is your memory card out of the slot?
I took a photo my bootloader (coloured) screen:
http://kepfeltoltes.pirateclub.hu/pics/20090106317.jpg My device doesnt say anything.
When i used the unlocker, i didnt got any code. And my memory card was in the slot.
I also took a photo what the Olipro's said now, if i try to continous the flashing:
http://kepfeltoltes.pirateclub.hu/pics/20090106319.jpg
Have you tried flashing your carrier's original Rom?
i will try it, but i dont know where can i find my original rom...
and my second biggest trouble: in this mode, i cant charge my batteries. If i dont find an solution this problem soon, i think, my device will be a BIG trouble. Grrr, i hate olipros program...
Thanks a lot, my athena is live again, i flash my original rom!!!
But the Olipros Unlockert isnt working, the installation go to 100%, the program said that the flashing is succesfull, but my SPL is still 1.1, and i cant flash any roms..
I can understand why. Any ideas?
The other thread was closed, you shouldn't double post.
Read the links I mentioned.
as in olis first post
"Please note: you must have .net Framework 2.0 installed with the services packs, if you don't it then it probably won't run till you download it.
SPECIAL INFO ABOUT STEP 2: When you run this step, first your device will be flashed; this is NOT the end of Step 2, you must then configure your device and set it up fully so you can access the menus etc (there will be a prompt to ask you to do this after the flash anyway). then you will be able to continue. please make sure to read ALL dialogs fully"
leave out the sim and sd card.
Some others have reported better luck with the shipped WM6 rom if they had trouble unlocking.
I installed the NET Framework 2.0 SP2 in my device and i put out my sim and sd card. And when i flashing the Olipros Unlocker, it went to 100%, but my SPL is still 1.1
I dont understand.
VorosAdam said:
I installed the NET Framework 2.0 SP2 in my device and i put out my sim and sd card. And when i flashing the Olipros Unlocker, it went to 100%, but my SPL is still 1.1
I dont understand.
Click to expand...
Click to collapse
the net framework should be on your computer.
what OS is on your computer ?
May be better if you use winXP
did you install an oficial wm6 rom ?
Read the later pages in the unlocker thread
My computer also have the NET Framework 2.0 SP2. And when the flashing didn't work, i also installed the NET Framework 3.5 SP1, but, when i flashing a ROM in my decive, it also went to 100%, but the SPL is still 1.1.
I use a 32-bit Windows XP in my computer.
My T-Mobile Ameo (Athena) is a second hand device, it was used when i bought. But the first user said me, that the original OS was the Windows Mobile 5 in my Athena, but he update from Windows Mobile 5 to Windows Mobile 6.0. He said that he update with an official T-Mobile way.
Ok all good so far
Did you use the unlocker from this thread?
http://forum.xda-developers.com/showthread.php?t=315831
The other thought i had was that you should try a different computer and usb cable
oh, thank you so mutch, i tried an another computer, and it flashed the SPL from 1.1 to 1.2!
thanks again
my htc advantaage x7500
hello myfrnd please help me as my phone is dead after i used ur rom upgrade 3.5, i was already using michy cooked version of window mobile 6.1 im new in this field and during upgrade process after going 92% it just stuck and and showing 3 color screen it has a msg of IPL 1.2 OLIPRO pls help me i will donate u if u could solve my problem
thanks
sheizi said:
hello myfrnd please help me as my phone is dead after i used ur rom upgrade 3.5, i was already using michy cooked version of window mobile 6.1 im new in this field and during upgrade process after going 92% it just stuck and and showing 3 color screen it has a msg of IPL 1.2 OLIPRO pls help me i will donate u if u could solve my problem
thanks
Click to expand...
Click to collapse
I saw someone with the same problem as you here awhile back and he was able to fix it. So keep your post alive or read the sticky post under the Upgrade section. I believe that was where I read it.
dead X7500
Hey Im also a sufferer of a dead X7500......this all happened wen I was trying to flash my ROM which was using a SPL !.20 OLIPRO
wen I try to re flash the device , it starts a stops at 1% and follows an error msg !
plzzzzzzzzzzzz help me out to solve this prob !
regards!
VorosAdam said:
i will try it, but i dont know where can i find my original rom...
and my second biggest trouble: in this mode, i cant charge my batteries. If i dont find an solution this problem soon, i think, my device will be a BIG trouble. Grrr, i hate olipros program...
Click to expand...
Click to collapse
I have the same problem would be kind and tell me how you solved the problem.
[email protected]
I need some expert help please! I have a Hermes (Orange SPV M3100) that I want to flash with a custom ROM but I am having a problem with ActiveSync losing the USB connection at the point that the device enters the bootloader screen. I am also unable to flash using the SD card method. I have flashed a Nike without any problems and I'm usually good with technical stuff so I think there must be something extra I need to do that I have missed. I hope that somebody can spare the time to help me solve the problem. Here are the details:-
I am trying to follow Mr Vanxs guide to flashing the ROM in windows Vista so that I can upgrade it from WM5 to WM6 and apply a custom ROM to load a new TouchFlo style OS. The first step in this process is to flash HardSPL using this guide but my problem with the USB connection won't let me do that. I have unlocked the device using Hermes Unlocker 3a so it is (or should be) SIM and CID unlocked and be SuperCID with HardSPL-1.40 (so maybe I can miss the Mr Vanxs HardSPL step?).
So, when I run the RUUWrapper.exe, choosing the Force option and accepting the messages I eventually get a prompt on the device. At this stage ActiveSync is connected. I click Yes on the device and it enters the bootloader screen which shows 'USB' on the tri-color screen but ActiveSync immediately drops the USB connection. The update then waits for a while then fails with Error 260. I have to do a soft reset to get the device out of the bootloader screen. When the device reboots the Activesync connection comes back to life.
I thought that I maybe don't need to HardSPL first so I tried just going straight to the ROM upgrade but I get the same problem.
Also, I tried following this link to flash using the SD card instead of USB but when I get to step 6 I don't see a confirm message - just the usual bootloader screen (it doesn't help that the screen shot doesn't appear on the link so I'm not even sure if I'm getting the correct screen). Any ideas?
I realise that an answer to this probably already exists somewhere on the forum but I have spent hours trawling through posts and I can't find it so I hope somebody has come across this before and can help me out.
Thanks guys!
Don't worry I solved it by rebooting my PC, skipping the HardSPL and flashing with an official ROM (HTC_TyTN_WWE_3.54.255.3_6275_1.48.00.10_108). I can now apply custom ROMs.
Hello Everybody,
My mobile at&t 8525 alias HTC 8525 is stuck in windows operator logo.It would not boot further. It happened while I tried to upgrade it from Windows 5.0 to Windows 6.0.First I got a tri-colour screen,but in a hurry I tried to backgrade to windows 5.0 again.
Other problem the mobile cannot be synced. I have installed Microsoft Active sync 4.5. Even then it could not be synced.
I tried to read all the posts ,but could not understand anything.
So please help me in getting my mobile repaired
Don't worie.
I had somewhat the same issue with a bad ROM flash.
Just disconnect the USB and boot to the bootloader screen (the tricolour screen) and you should be able to reflash the phone again.
Problem in syncing the mobile
I am not able to sync the mobile to the laptop.I have installed Microsoft Active sync 4.5. Even then it is not syncing.So how could I run the hermes upgrade if the mobile is not helping.
Please help
In Activesync on PC - Untick "Allow USB Connections".
Put the Hermes into bootloader (tri-colour screen) and connect by usb. Run the RUU_Wrapper.exe file you want. Follow onscreen instructions.
You need to have installed Hard SPL V7 for this to work...
did not work
Hello Boss
I tried to follow the procedure you suggested me. but it did not work. I tried with Hard SPl 7.0.
Please give me some suggestion
you dont need an active sync connection to flash it. Enter bootloader(tri colour screen) as you were told in the previous posts and Just click on the boxes that you do have a connection(even though you dont) and then flash the rom.
@ultramag69 i hve never had to untick allow usb connections and i have cocked up loads of rom flashes, saying that i have never had a problem flashing in vista either so maybe i am lucky
If you still cant flash doing it this way, then maybe you should try flashing from sd card instead, just make sure the battery is fully charged. Full instructions of how to do this are found in the hermes wiki, which i advise you to read anyway.
Oh and good luck anyway, you should be able to recover the phone from this ,so i wouldnt fret too much
Guess he isnt hardspl'ed... then his batt is death... must to flash a shipped rom.
correct me if im wrong.
Problem with upgrade At&T 8525 mobile
Hi!
I'm having problems with my Cingular 8525, after I made the upgrade to WM6.1 (FARIA-R32-XDA2_WM6.1.rar) for WM 6.5 (FCWs_stock_like_6.5_v3.rar), and slowed my device does not work anymore. He died.
I need help please. How resurrect it?
Excuse my English.
english is not the problem here cause we need more info... device info SPL IPL hardSPL? you go from 6.5 to 6.1?
Do you try to flash first the Stripped?
Does your batt has charge enough to boot?
There are many many things to say so... start to tell us all your history!
Hi
I tried to Hard spl with Hard Splv7. But I got a error. I even tried the Sd Card method.Its says loading and I get the tricolour mode. If I press the Power button its not showing the status of upgradation.
Where can I get a shipped rom. Actually my Spl is 1.11.
Hi
I tried to Hard spl with Hard Splv7. But I got a error. I even tried the Sd Card method.Its says loading and I get the tricolour mode. If I press the Power button its not showing the status of upgradation.
Where can I get a shipped rom. Actually my Spl is 1.11.
check the wiki pages for your device in the upper bar of this web forums
there are many official roms.
I also am currently using an 8525 (Herm100). It was received from an Ebay deal with WM5. I flashed it with the ATT OEM WM6pro (aka shipped wm6). Once it hit the three color boot screen, it sat on that for a couple of minutes then started cooking. Once it showed a progress bar, it took about 3 minutes to cook the WM6 over the WM5. It also showed a popup that stated going back to WM5 was not an option.
I would suggest running the installer again and going down to 7-11 for a refreshment. You may not have let it percolate long enough to set itself up for the actual ROM overwriting.
gorkalraghavendra said:
Hello Everybody,
My mobile at&t 8525 alias HTC 8525 is stuck in windows operator logo.It would not boot further. It happened while I tried to upgrade it from Windows 5.0 to Windows 6.0.First I got a tri-colour screen,but in a hurry I tried to backgrade to windows 5.0 again.
Other problem the mobile cannot be synced. I have installed Microsoft Active sync 4.5. Even then it could not be synced.
I tried to read all the posts ,but could not understand anything.
So please help me in getting my mobile repaired
Click to expand...
Click to collapse