Help please!
I have an T-Mobile Ameo (also known Athena X7500) and i tried the Olipro Unlocker, but the installation didnt finish, at 59% stopped. After that i turn off the device, then turn on, but my device still have a 4 colour screen,red, green, blue and white, it doesnt boot the Windows Mobile, just have the installation screen...
please help
Use olipro's tool again and then flash your final ROM
i tried it many times, but since than my Athena X7500 was dead, the Olipros unlocker doesnt work. The program said: "The Update Utility cannot connect your PDA phone"
In bootloader (coloured screen), does it say anything? if so what? when you try to flash a rom or use unlocker do you get a code? is your memory card out of the slot?
I took a photo my bootloader (coloured) screen:
http://kepfeltoltes.pirateclub.hu/pics/20090106317.jpg My device doesnt say anything.
When i used the unlocker, i didnt got any code. And my memory card was in the slot.
I also took a photo what the Olipro's said now, if i try to continous the flashing:
http://kepfeltoltes.pirateclub.hu/pics/20090106319.jpg
Have you tried flashing your carrier's original Rom?
i will try it, but i dont know where can i find my original rom...
and my second biggest trouble: in this mode, i cant charge my batteries. If i dont find an solution this problem soon, i think, my device will be a BIG trouble. Grrr, i hate olipros program...
Thanks a lot, my athena is live again, i flash my original rom!!!
But the Olipros Unlockert isnt working, the installation go to 100%, the program said that the flashing is succesfull, but my SPL is still 1.1, and i cant flash any roms..
I can understand why. Any ideas?
The other thread was closed, you shouldn't double post.
Read the links I mentioned.
as in olis first post
"Please note: you must have .net Framework 2.0 installed with the services packs, if you don't it then it probably won't run till you download it.
SPECIAL INFO ABOUT STEP 2: When you run this step, first your device will be flashed; this is NOT the end of Step 2, you must then configure your device and set it up fully so you can access the menus etc (there will be a prompt to ask you to do this after the flash anyway). then you will be able to continue. please make sure to read ALL dialogs fully"
leave out the sim and sd card.
Some others have reported better luck with the shipped WM6 rom if they had trouble unlocking.
I installed the NET Framework 2.0 SP2 in my device and i put out my sim and sd card. And when i flashing the Olipros Unlocker, it went to 100%, but my SPL is still 1.1
I dont understand.
VorosAdam said:
I installed the NET Framework 2.0 SP2 in my device and i put out my sim and sd card. And when i flashing the Olipros Unlocker, it went to 100%, but my SPL is still 1.1
I dont understand.
Click to expand...
Click to collapse
the net framework should be on your computer.
what OS is on your computer ?
May be better if you use winXP
did you install an oficial wm6 rom ?
Read the later pages in the unlocker thread
My computer also have the NET Framework 2.0 SP2. And when the flashing didn't work, i also installed the NET Framework 3.5 SP1, but, when i flashing a ROM in my decive, it also went to 100%, but the SPL is still 1.1.
I use a 32-bit Windows XP in my computer.
My T-Mobile Ameo (Athena) is a second hand device, it was used when i bought. But the first user said me, that the original OS was the Windows Mobile 5 in my Athena, but he update from Windows Mobile 5 to Windows Mobile 6.0. He said that he update with an official T-Mobile way.
Ok all good so far
Did you use the unlocker from this thread?
http://forum.xda-developers.com/showthread.php?t=315831
The other thought i had was that you should try a different computer and usb cable
oh, thank you so mutch, i tried an another computer, and it flashed the SPL from 1.1 to 1.2!
thanks again
my htc advantaage x7500
hello myfrnd please help me as my phone is dead after i used ur rom upgrade 3.5, i was already using michy cooked version of window mobile 6.1 im new in this field and during upgrade process after going 92% it just stuck and and showing 3 color screen it has a msg of IPL 1.2 OLIPRO pls help me i will donate u if u could solve my problem
thanks
sheizi said:
hello myfrnd please help me as my phone is dead after i used ur rom upgrade 3.5, i was already using michy cooked version of window mobile 6.1 im new in this field and during upgrade process after going 92% it just stuck and and showing 3 color screen it has a msg of IPL 1.2 OLIPRO pls help me i will donate u if u could solve my problem
thanks
Click to expand...
Click to collapse
I saw someone with the same problem as you here awhile back and he was able to fix it. So keep your post alive or read the sticky post under the Upgrade section. I believe that was where I read it.
dead X7500
Hey Im also a sufferer of a dead X7500......this all happened wen I was trying to flash my ROM which was using a SPL !.20 OLIPRO
wen I try to re flash the device , it starts a stops at 1% and follows an error msg !
plzzzzzzzzzzzz help me out to solve this prob !
regards!
VorosAdam said:
i will try it, but i dont know where can i find my original rom...
and my second biggest trouble: in this mode, i cant charge my batteries. If i dont find an solution this problem soon, i think, my device will be a BIG trouble. Grrr, i hate olipros program...
Click to expand...
Click to collapse
I have the same problem would be kind and tell me how you solved the problem.
[email protected]
Related
Ok, I've been trying to update my 8525 for hours...here is my problem. First, I tried to HardSPL-v7 but I kept getting an "Error [240] File open". I think this is preventing me from doing any ROM update. When I try to run the Cingular ROM update activesync shuts down and I get a connection error, I think it is "error [260]". I have wiped or cleaned out my 8525 so that I am back to day one. I have tried both ROM updates on 2 separate computers and I get same error messages on both computers. I have searched the Wiki's but have found nothing, so please help. As you can tell, I am a virgin to ROM updates so please go gently.
I should add, my present ver. ROM AKU 2.3 (1.34.502.7018.01H) SPL 1.06 IPL 1.01. Radio is 1.16.
have you taken a look at my Safe WM5 Upgrade Guide??
If you follow this guide EXACTLY, you should be fine.
mrvanx said:
have you taken a look at my Safe WM5 Upgrade Guide??
If you follow this guide EXACTLY, you should be fine.
Click to expand...
Click to collapse
I have, I have even tried the mtty "fix" but I had problems with that as well. I get a modem connection screen but there is nothing about a USB connection.
Bit more info would be nice, which ROM are downloading, and where from??
Also what procedure are you doing to update?? EXACT info please.
mrvanx said:
have you taken a look at my Safe WM5 Upgrade Guide??
If you follow this guide EXACTLY, you should be fine.
Click to expand...
Click to collapse
Ok, I just tried it 2 more times, Hard-SPL. It flashes to the 8525 and goes into bootloader and shows the following "HERM100 IPL-SSPL by Des HERM100 SPL-1.09.ds" at this point activesync 4.5 shuts down the 8525 is stuck in bootloader (it never reboots) and after a few minutes I get "Error [260] Upated Error". Hard SPL shuts down and the 8525 is stuck in bootloader mode. At this point I have been disconnecting the USB cable and doing a soft reset, once the phone is on, I go into bootloader and the old info shows up SPL 1.06 and IPL 1.01.
Let me have a think, firstly do you have the latest versions of the .net framework installed?
I was able to finally run HardSPLv7, I had to do it on another computer. Now, I would like to update to RUU_Hermes_CINGULAR_WWE_2.15.502.3_6275_1.40.30.00_108_Ship.exe. I assume I should use the same computer that I used to successfully run HardSPL. Do I need to rebuild the rom file with RUUWrapper.exe (CustomRUU by olipro) & Dutty's Good NBH Tool, before running the RUU_Hermes_CINGULAR_WWE_2.15.502.3_6275_1.40.30.00_108_Ship.exe update?
mrvanx said:
Let me have a think, firstly do you have the latest versions of the .net framework installed?
Click to expand...
Click to collapse
I have .Net 1 thru 3.5 (pre-release) installed on the computer that I can not get to run any ROM updates.
9
compudds said:
I was able to finally run HardSPLv7, I had to do it on another computer. Now, I would like to update to RUU_Hermes_CINGULAR_WWE_2.15.502.3_6275_1.40.30.00_108_Ship.exe. I assume I should use the same computer that I used to successfully run HardSPL. Do I need to rebuild the rom file with RUUWrapper.exe (CustomRUU by olipro) & Dutty's Good NBH Tool, before running the RUU_Hermes_CINGULAR_WWE_2.15.502.3_6275_1.40.30.00_108_Ship.exe update?
Click to expand...
Click to collapse
Yes if you carry on the guide past flashing hardspl you will get the radio updated aswell.
Can i ask, what is different on the computer you used???
mrvanx said:
Yes if you carry on the guide past flashing hardspl you will get the radio updated aswell.
Can i ask, what is different on the computer you used???
Click to expand...
Click to collapse
Off hand, the major difference would be Intel (worked) vs. AMD (failed) but I doubt that is the problem, you would be flooded with questions due to so many computers that have AMD chips. The USB cable was the same as well. I'll have to think about that...
Definatly check your "failed" computer is up to date with .net and everything else, most likely a software problem.
I have this problem as well..
AT&T 8525 windows moble 6 trying to install the hardspl v7.
v3.5 and 3.0 .net framework.
the RUUwrapper program gets to the 'verifiying info' screen then give me an erroe 240 message. 'the update utility can not open the requested file.'
any help would be great. Looking to add the touch it interface.
thanks,
Mike
Read the post Hard SPL at the top of this forum and go to page 116 ( I believe its post #1160) and use the sd card method. You don't need to use the pc at all. I generally flasah ALL os's using the sd card method as it seems to be safer then using the usb method. No "sync errors" to deal with.
Cheers...
I have the exact same problem..
When it goes to tri-color screen, the USB connection goes off and windows will pop up the search for driver dialogue box.. then afterward another dialogue box will appear saying Error [260].
I tried restarting my pc and device (even removing the battery) but still failure
Any help would be highly appreciated. Thanks.
blackphnx said:
I have the exact same problem..
When it goes to tri-color screen, the USB connection goes off and windows will pop up the search for driver dialogue box.. then afterward another dialogue box will appear saying Error [260].
I tried restarting my pc and device (even removing the battery) but still failure
Any help would be highly appreciated. Thanks.
Click to expand...
Click to collapse
I loaded it thru the sd card just as the post above suggested. It loaded the hardspl just fine. My PPC seems to run faster as well.
Thanks for the help! it is much appreciated.
blackphnx said:
I have the exact same problem..
When it goes to tri-color screen, the USB connection goes off and windows will pop up the search for driver dialogue box.. then afterward another dialogue box will appear saying Error [260].
I tried restarting my pc and device (even removing the battery) but still failure
Any help would be highly appreciated. Thanks.
Click to expand...
Click to collapse
One thing that i have learned from flashing my 8525 is to remove any USB device except the 8525. This has worked for me.
swimmy said:
One thing that i have learned from flashing my 8525 is to remove any USB device except the 8525. This has worked for me.
Click to expand...
Click to collapse
But my mouse is on USB. I might try on different computer and post back the results.
UPDATE
I tried using my friend's laptop and it installed without a problem. I think the issue is with the .NET framework. I installed the latest one before flashing and it worked fine. Hmmm.. Im not sure about this tho.
Hello.... Try the sd card method. You don't need the computer...
Sorry if I sound condescending, but, I seem to find a lot of people saying that they have sync problems. Solution, Take the pc out of the equation (except to load files onto sd card). It is SOOO much safer then using the pc, no "sync" problems, no chance of usb being disconnected, reset button being hit or , worst case scenario, power failure...
You have to either have little or no battery power or MANUALLY hit the reset button with the stylus to stop the flash...
And thats my 2 cents....
Refer to post #13 to find out how to use sd card method to flash hard spl...
Cheers...
sd card method???
how?
Hello, I am in serious trouble! I got a brand new HTC Athena with Windows Mobile 5.0. I succesfully upgrade it to Windows Mobile 6.0.
All was OK.
Than I was interested to move into Windows Mobile 6.1 and possibly 6.5. At first I did the Athena unlock (3 step process) and all went OK: Antenna 1.5.0, SPL 1.2 OLI....
THAN I DID MY ERROR! I try to upgrade my 6.0 ROM with the Micky 6.1 cooked file with SPL 3.5. After a 92 percent upgrade, the ROM crashed and now I always get a nasty black screen with few lines (No 3 color bands!). When I try to upgrade again the same ROM or ROM for SPL 1.2 I get an error (ID mismatching). I guess the only solution is a hard and full reset of the Windows. But doing only a hard reset with the PDA will NOT change my error message and I will keep see this nasty black screen and I cannot load the Windows ActiveSync application-
I am totally lost. Help please. Any tool for a true full restore/recover??? (I did NOT make any backup!).
This thread might hold a solution to your problem.
Hi
If you follow the instructions exactly in post 33, it will solve your problems. just click HERE
Jay
Hello, those links are basically for corrupted wifi antenna files.-
In my case my HTC Athena crashed the Windows 6 ROM while I was attempting to upgrade, after unlocking the phone, the Athena from version 6.0 to version 6.1
Are you sure I can use the post #33 also for my specific trouble?
Thank you in advance!
this is also to repair your bootloader-infos
if you look at your bootloaderscreen, you will see ATHE100, IPL, ATHE100, SPL. if not, you have to repair it
make sure you flashed the right rom, spl 1 or 3.5
How can the bootloader get repaired?
yes use that link, post #33. fixes both wifi and modelid problems and bootloader problems when you got stuck at 92% of the flashing process.
Cannot re flash ROM
Please help! I tried the unlocker and it failed at 92% and since then I have no WM6. Then I tried to flash the Michy WM6.5 and that failed. I was getting model id errors so I did the mtty and mac1 fix which was succesful. However all I can get now is a grey screen on boot-up. I can get to the bootloader screen and it displays ATHE100, IPL-v2.02, ATHE100, SPL-v1.20. Olipro. From what I have read on the forum at this stage I should run a RUU to flash a WM6 ROM but all that I try can't connect because no OS running to connect with Activesync? Is there a way to flash from the bootloader? The other option seems to be putting an image and flasher on a miniSD but I can't find clear instructions for this or which files?
Please ignore - my battery wasn't charged enough. Replaced battery and recovered device.
Still Major Problem! Help me! Have mercy!
Hello Responderman, all,
I have follow the link (thread 33)...., however, after I have typed lnbs filename.bin 75108000 (I have SPL 1.2), I got in mtty the "code entrypoint unknown" message, which should be ok......
However, after I have disconnected the usb cable of the Athena from the PC and try to reboot it, I got again the exact same, nasty, dark screen with blue strips.....:-( It means that my damaged firmware has NOT been fix and in fact I am still NOT able to boot WM successfully!
PLEASE HELP. It is 3 months with this problem and I cannot use my device.:-(
Still Major Problem! Help me! Have mercy!
Hello Responderman, all,
first, how can I get the mac address of my device? It is NOT written anywhere in the Athena parts (checked in the battery bay and so on.....), and so when I run mtty i am in trouble! I have used a mac address got from my company's manager, but not sure it is ok to use it with the Athena!
Anyway,......I have follow the post link (thread 33)...., and followed the various steps.- However, after I have typed lnbs filename.bin 75108000 (I have SPL 1.2), I got in mtty the "code entrypoint unknown" message, which should be ok......
However, after I have disconnected the usb cable of the Athena from the PC and try to reboot it, I got again the exact same, nasty, dark screen with blue strips.....:-( It means that my damaged firmware has NOT been fix and in fact I am still NOT able to boot WM successfully!
PLEASE HELP. It is 3 months with this problem and I cannot use my device.:-(
Solved!
Hi, problem done. I have follow the remarks, fixed my broken firmware and now I use well Athena with VM 6.5! Thanks all for your help!
puffo said:
Hi, problem done. I have follow the remarks, fixed my broken firmware and now I use well Athena with VM 6.5! Thanks all for your help!
Click to expand...
Click to collapse
Can you tell what you've actually done after you've changed ROM with Mtty?
I done the thing with Mtty but just as you described when I reset it now I still get the grey screen. And if I try to update ROM it fails again on 92%
where did you find the upgrade from wm5 to wm6?
the link I found on rapidshare seems not be availabel anymore
http://forum.xda-developers.com/showthread.php?p=3909674#post3909674
HERMES (htc tytn) UPGRADE FAILURE
REPORT
Hi all of you!
I have a Hermes (HTC Tytn/ Orange SPV M3100) and i succesfully tried a lot of ROM’s until these days..
But, this happened:
During upgrade of a ROM, i made the mistake to disconect the device from the PC..
And, now the problem is that i can’t boot ANY OTHER ROM!
I can enter to BootLoader , where i see
HERM100
I PL – 1.04
HERM100
SPL – 2.03
ALSO, i CAN connect to PC (it displays „usb” & i see it on Device manager)
(PC run Vista Ultimate 64 bit).
But, when i try to upgrade ANY ROM , the process starts, BUT STOPS at 0% ? .
I searched & read 4 days for a SOLUTION to make my phone alive again..
Can anyone tell me what to do?
Is a REAL solution for this issue?
Please reply.
Thanks!
i GUESS YOUR BATT IS ALMOST DEAD!
Hi dude... does your batt is higher than 50%? the process will not continue if yuour device is under 50% maybe it is beacause you cant charge it in Bootloader. keep it higher than that... if not the case... i guess you will ned to clean it with mtty....
Just search something like that... im for sure there is a way to make it... use the stripped att rom
AND TRY WITH IT ALWAYS!!!
never but never! when you got a problem in upgrade NEVER do a hardreset.... just softreset... keep it on mind... try an XP machine get it wherever you need to get it!
thanks
..a lot for the reply!
i tried on a XP-PC, because mtty don't work in Vista (Ultimate x64)
i followed ALL the instructions..BUT..
..the problem persists!(
thanks for the idea of battery i will try again, with full of..
also, i will try some ROM's without radio's..hope that help..
BTW:
in mtty shows that the device is CID locked with:
"ORANG008"
i downloaded the last ROM for Orange 008, and tried of install...BUT..nothing!(
any other sugestion, please?
thanks again!
Hello Everybody,
My mobile at&t 8525 alias HTC 8525 is stuck in windows operator logo.It would not boot further. It happened while I tried to upgrade it from Windows 5.0 to Windows 6.0.First I got a tri-colour screen,but in a hurry I tried to backgrade to windows 5.0 again.
Other problem the mobile cannot be synced. I have installed Microsoft Active sync 4.5. Even then it could not be synced.
I tried to read all the posts ,but could not understand anything.
So please help me in getting my mobile repaired
Don't worie.
I had somewhat the same issue with a bad ROM flash.
Just disconnect the USB and boot to the bootloader screen (the tricolour screen) and you should be able to reflash the phone again.
Problem in syncing the mobile
I am not able to sync the mobile to the laptop.I have installed Microsoft Active sync 4.5. Even then it is not syncing.So how could I run the hermes upgrade if the mobile is not helping.
Please help
In Activesync on PC - Untick "Allow USB Connections".
Put the Hermes into bootloader (tri-colour screen) and connect by usb. Run the RUU_Wrapper.exe file you want. Follow onscreen instructions.
You need to have installed Hard SPL V7 for this to work...
did not work
Hello Boss
I tried to follow the procedure you suggested me. but it did not work. I tried with Hard SPl 7.0.
Please give me some suggestion
you dont need an active sync connection to flash it. Enter bootloader(tri colour screen) as you were told in the previous posts and Just click on the boxes that you do have a connection(even though you dont) and then flash the rom.
@ultramag69 i hve never had to untick allow usb connections and i have cocked up loads of rom flashes, saying that i have never had a problem flashing in vista either so maybe i am lucky
If you still cant flash doing it this way, then maybe you should try flashing from sd card instead, just make sure the battery is fully charged. Full instructions of how to do this are found in the hermes wiki, which i advise you to read anyway.
Oh and good luck anyway, you should be able to recover the phone from this ,so i wouldnt fret too much
Guess he isnt hardspl'ed... then his batt is death... must to flash a shipped rom.
correct me if im wrong.
Problem with upgrade At&T 8525 mobile
Hi!
I'm having problems with my Cingular 8525, after I made the upgrade to WM6.1 (FARIA-R32-XDA2_WM6.1.rar) for WM 6.5 (FCWs_stock_like_6.5_v3.rar), and slowed my device does not work anymore. He died.
I need help please. How resurrect it?
Excuse my English.
english is not the problem here cause we need more info... device info SPL IPL hardSPL? you go from 6.5 to 6.1?
Do you try to flash first the Stripped?
Does your batt has charge enough to boot?
There are many many things to say so... start to tell us all your history!
Hi
I tried to Hard spl with Hard Splv7. But I got a error. I even tried the Sd Card method.Its says loading and I get the tricolour mode. If I press the Power button its not showing the status of upgradation.
Where can I get a shipped rom. Actually my Spl is 1.11.
Hi
I tried to Hard spl with Hard Splv7. But I got a error. I even tried the Sd Card method.Its says loading and I get the tricolour mode. If I press the Power button its not showing the status of upgradation.
Where can I get a shipped rom. Actually my Spl is 1.11.
check the wiki pages for your device in the upper bar of this web forums
there are many official roms.
I also am currently using an 8525 (Herm100). It was received from an Ebay deal with WM5. I flashed it with the ATT OEM WM6pro (aka shipped wm6). Once it hit the three color boot screen, it sat on that for a couple of minutes then started cooking. Once it showed a progress bar, it took about 3 minutes to cook the WM6 over the WM5. It also showed a popup that stated going back to WM5 was not an option.
I would suggest running the installer again and going down to 7-11 for a refreshment. You may not have let it percolate long enough to set itself up for the actual ROM overwriting.
gorkalraghavendra said:
Hello Everybody,
My mobile at&t 8525 alias HTC 8525 is stuck in windows operator logo.It would not boot further. It happened while I tried to upgrade it from Windows 5.0 to Windows 6.0.First I got a tri-colour screen,but in a hurry I tried to backgrade to windows 5.0 again.
Other problem the mobile cannot be synced. I have installed Microsoft Active sync 4.5. Even then it could not be synced.
I tried to read all the posts ,but could not understand anything.
So please help me in getting my mobile repaired
Click to expand...
Click to collapse
I have a problem:
I flashed my hd2 from a stocked rom 1.42 dutch version, with hspl 1.42. I installed a custom rom from: HTC HD2 Laurentius WWE 21891UltimatePOWER.
it worked fine for 2 or 3 days and then it stocked, i reseted the phone and
When i turn on my HD2, i get a white screen. and it doest go away. Even after softreset (volume button down in bootloader)
When i go in to bootloader i see this screen:
Pb81100 hx-bc
Spl-1.42.hspl xe
0x05
Cotullahspl 0x30
Click to expand...
Click to collapse
When i try to instal a rom by going in to bootloader en then start in win xp the update wont start, it stocked at 0 %
Then i tried to flash a orginal romt by sd:
it stocked at 7 % and i get this screen:
_______________________RUUNBH
PB81100___HX-BC
SPL-1.42.__hspl___XD
________________0x05
CotullaHSPL______0x30
Upgrade ROM code error
Please try again
Click to expand...
Click to collapse
- Then i tried to flash a radio rom by activesync, in xp it wont start,
- i tried flashing by sd and it stocked on 98%
- I tried different to install a rom and radio rom by vista, but also no succes
- I tried task 29 (by the Attached Task29 into a single exe.) to erease all data from the phone, but in windows by activesync it wont start
i tried al the above from windows 7.
Is there anyone that can help me, please i getting very desperate.
VERY VERY IMPORTANT! Try and read 2-3 times what is written here http://forum.xda-developers.com/showthread.php?t=609477
Only afterwards proceed to the following :
First of all....try and use Windows Vista or Windows 7.
Second of all....do not try to use task 29 because its a bit more complicated and it involves some drivers and so on!
Use this little thing here http://forum.xda-developers.com/showpost.php?p=5848003&postcount=19 and after its completed....flash a proper radio something like 2.08.50.xx which you can find on Radio dedicated section here http://forum.xda-developers.com/showthread.php?t=611787
After all these....flash a custom ROM but be careful to be one suited with your radio! Which is a radio appliable for most of custom ROMS BUT be VERY careful!
Another thing.....do not flash from SD Card....Use the CustomRUU tool and flash it via ActiveSync!
Do you get any particular error message? When in bootloader mode, does "usb" show at the bttom of the screen? If so, try moving to a different usb port, preferably at the rear of the pc, or try different cable or even different pc. If still no luck, try uninstalling and then re-installing the latest version of Activesync.
The White Screen issue sounds like the incorrect radio version for the rom. I'm not familar with the details of the particular rom, but there are certain rom/radio combinations that will do that if they do not match eg running a 2.10 based rom with a x.xx.51.xx radio. The phone works intially until a reset and then hangs.
viperd said:
VERY VERY IMPORTANT! Try and read 2-3 times what is written here ......
Click to expand...
Click to collapse
Thanks for the replay
I tried, flashing by activesync. i flashed it the first time by hspl (the tread you link to) and then by activesync. But like i said, the hd2 stops at a white screen, so i tried by every possible way i could think of. Also i tried task 39 by the tool you mention, but it still does not work.
But i will correct my ts.
@clydeb1
I tryd to flash different radioroms, but if it try by activesync it wont start and by sd-flash it stocks at 98%, but i will try a different active sync
Okay,
I tried the following options:
- I installed a newest activesync and tried to instal an new rom under windows xp. The update stocked at 0% and i tried to install radio rom, with the same results
- I installed the windows mobile on windows 7, and tried the same as in windows xp, and still the same results.
Then i tried flashing every rom from the site by the sd-method (after every bad flash i formatted the sd-card with fat32)
With the sd method the phone stocked at 99% and then gives the next images:
00018003
LEOIMG.nbh - Fail
Radio_V2Fail
Update terminate
update fail
Click to expand...
Click to collapse
IS there any one how has a solution for this problem
Ok....try from the beginning!
1.Get from here http://forum.xda-developers.com/showthread.php?t=611433 HSPL2_RUN.zip (extract the content in a folder named hspl ).2
2. For Windows 7 you need Windows Mobile Device Center ( WMDC ) NOT ActiveSync!! Get it here http://www.microsoft.com/windowsmobile/en-us/downloads/microsoft/device-center-download.mspx
3. Make sure in WMDC settings the USB connection is checked!
4. Take out your battery....insert it again! Start your phone while keeping pressed the Vol Down button! This will get you into bootloader! The screen should display USB on the lower part of the screen! (evidently connected to computer )
5. Flash HSPL2 select 2.08 version
6. Use that tool I recommended earlier.....http://forum.xda-developers.com/show...3&postcount=19
7. Enter again the bootloader and flash a Radio ROM ( try 2.08.50.xx ) via WMDC!
8. Flash either NRGZ 21898 or Cleanex 21898 versions ( I recommend these in particular because they work with the radio mentioned above and are also stable ROMs ).
P.S. Take out your SD card and SIM card while performing all these steps!
Hope you will solve it!
viperd said:
Ok....try from the beginning!
1.Get from here (extract the content in a folder named hspl ).2
2. For Windows 7 you need Windows Mobile Device Center ( WMDC ) NOT ActiveSync!! Get it here
3. Make sure in WMDC settings the USB connection is checked!
4. Take out your battery....insert it again! Start your phone while keeping pressed the Vol Down button! This will get you into bootloader! The screen should display USB on the lower part of the screen! (evidently connected to computer )
5. Flash HSPL2 select 2.08 version
6. Use that tool I recommended earlier.....
7. Enter again the bootloader and flash a Radio ROM ( try 2.08.50.xx ) via WMDC!
8. Flash either NRGZ 21898 or Cleanex 21898 versions ( I recommend these in particular because they work with the radio mentioned above and are also stable ROMs ).
P.S. Take out your SD card and SIM card while performing all these steps!
Hope you will solve it!
Click to expand...
Click to collapse
Thanks for the advise
I did every step. The first problem is: WMDC doest say there is a connection, while windows 7 say there is a connection also i see usb in the lower part of the screen.
In the same sequence as you right above. the hspl2 says it worked fine, but when i reset the boatlooder still says it has hspl 1.42 in stead of 2.08. The tool you recommended did't start. and says update error.
do you know something else i could do (or anyone else)
Give the phone to someone who can get it to work??
Give me your SD-CARD serial number.
I'ma make a goldcard for you.
sd-card max to 4gb!
And then try flashing stock nld 1.66 rom using sd-card.
Because you tried to fix it flashing a 'original rom?' from sd I think I know what's your problem.
Did you use a Dutch shipped rom while trying to fix or a WWE one?
If you flash a shipped rom from storage card it restores the original SPL and removes HSPL !
Try flashing a Dutch shipped rom one more time from storage card, it will restore the original SPL made for your device.
korenbloem said:
Thanks for the advise
I did every step. The first problem is: WMDC doest say there is a connection, while windows 7 say there is a connection also i see usb in the lower part of the screen.
In the same sequence as you right above. the hspl2 says it worked fine, but when i reset the boatlooder still says it has hspl 1.42 in stead of 2.08. The tool you recommended did't start. and says update error.
do you know something else i could do (or anyone else)
Click to expand...
Click to collapse
Thanks mate, if my suggestion doesn't work hopefully you can help him.
xmoo said:
Give me your SD-CARD serial number.
I'ma make a goldcard for you.
sd-card max to 4gb!
And then try flashing stock nld 1.66 rom using sd-card.
Click to expand...
Click to collapse
@Korenbloem,
A simple hardreset would have fixed your issue as well.
Instead of all kind of panic experiments like mtty/ flashing radios/roms from sd you could have come to me and I would have helped you.
You flashed a very old rom from the rom archive but never the less that rom is intensivily tested by me and the beta team.
I have no idea what kind of software you installed/tweaks you did or anything else but also with installing the wrong software it could cause the rom not to boot anymore.
Sorry to tell you but these 'bricking' stories are mostly caused by unexperiened users and it
making me sad to see more people are opening threads like this blaming a rom and causing a panic reaction in public destroying our work.
I realy hope you fix your device and I will try to help you but this isn't a rom issue.
Leo
Laurentius26 said:
Because you tried to fix it flashing a 'original rom?' from sd I think I know what's your problem.
Did you use a Dutch shipped rom while trying to fix or a WWE one?
If you flash a shipped rom from storage card it restores the original SPL and removes HSPL !
Try flashing a Dutch shipped rom one more time from storage card, it will restore the original SPL made for your device.
Click to expand...
Click to collapse
Thanks for the adivse, but i already tried that with an orginal rom, but i will try it again, mabey there is a difference with a shipped rom.
The first thing i did was a hard reset, but that did't worked. (the phone is in this shape for 1 month now).
Second. I am not blaming you or anyone. I flashed the wrong radio rom i think (cant remember witch one) And that is my own fault. I never wanna make the suggestion that it is because of youre rom.
I took a risk by flashing my phone. and i is my responsibility.
Edit: I tried a shipping rom nld. But it gives the same error as always, only after 7%. But thanks for the advise
@ Xmoo, First of al thank you that you want to help with a sollution. But what does that mean a goldcard and what are the consequences of using it.
Laurentius26 helped me with fixing my device.
The problem was the radio. and by flashing a factory rom from t-mobile, the hspl was reset to spl 2.00. After that he flashed a orginal shipped rom (the orignal one from my device). And the rom is fixed again SPL 1.66 is now on the device.
Laurentius thanks for al the help!!!!!
HD2 bricked?
Hi, I urgently need your help. I used my hd2 on a vodafone branded rom 1.44. Last week I installed a Vodafone NLD 1.72 rom , + froyostone 3.4 Rom,kernel 8.5 (with hspl). Yesterday my touchscreen has stopped fully .. . The next, I've been in touch with HTC and they will pick up my phone tomorrow for repair. I have to remove hspl ofcourse .. so I happily try to flash official vodafone rom from the SD card, did nothing 1.72, 1.48 seemed to do until I restart and got an ROM code error. What to do: ( I am pretty desperate now .. when you start you get an exclamation point and then 'not allow' and then the tricolor. Is this due to the lack of the original 1.44 ROM? Apologies for this begging post and my poor English but I hope that someone has a solution to unbrick this device so he can up picked by HTC.
vanbasten88 said:
Hi, I urgently need your help. I used my hd2 on a vodafone branded rom 1.44. Last week I installed a Vodafone NLD 1.72 rom , + froyostone 3.4 Rom,kernel 8.5 (with hspl). Yesterday my touchscreen has stopped fully .. . The next, I've been in touch with HTC and they will pick up my phone tomorrow for repair. I have to remove hspl ofcourse .. so I happily try to flash official vodafone rom from the SD card, did nothing 1.72, 1.48 seemed to do until I restart and got an ROM code error. What to do: ( I am pretty desperate now .. when you start you get an exclamation point and then 'not allow' and then the tricolor. Is this due to the lack of the original 1.44 ROM? Apologies for this begging post and my poor English but I hope that someone has a solution to unbrick this device so he can up picked by HTC.
Click to expand...
Click to collapse
Do you have a branded Leo? If so, enter bootloader (remove battery, press volume down, insert battery), connect via usb (maybe you have to wait for driver installation), start the latest *.exe from your operator/carrier...
same problem here flashing an old radio... and now, everytime i try to flash a factory rom ship (RUU_Leo_HTC_PTG_1.66.410.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship) on 1% get the error 244 - invalid model id.
I tried to hard reset and now the message on the bottom of screen show me the right factory radio (2.06.51.07) of this rom but stays on this screen forever anyone knows what can i do? please help... tks a lot!
andreftx said:
same problem here flashing an old radio... and now, everytime i try to flash a factory rom ship (RUU_Leo_HTC_PTG_1.66.410.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship) on 1% get the error 244 - invalid model id.
I tried to hard reset and now the message on the bottom of screen show me the right factory radio (2.06.51.07) of this rom but stays on this screen forever anyone knows what can i do? please help... tks a lot!
Click to expand...
Click to collapse
Maybe it is because you flashed the wrong stock rom.
You should find the CORRECT STOCK ROM for your device, otherwise you need a gold card
silverwind said:
Maybe it is because you flashed the wrong stock rom.
You should find the CORRECT STOCK ROM for your device, otherwise you need a gold card
Click to expand...
Click to collapse
sorry but this rom i've downloaded from htc.com after insert model and my hd2 serial number and work for a while, but after flash hspl 1.42 to install another rom, when i flash a new radio version get the problem! so i flash again hspl to recovery for SPL 1.42.000 and then, nothing more is functional
tks 4 help... have anyone other solution?
andreftx said:
sorry but this rom i've downloaded from htc.com after insert model and my hd2 serial number and work for a while, but after flash hspl 1.42 to install another rom, when i flash a new radio version get the problem! so i flash again hspl to recovery for SPL 1.42.000 and then, nothing more is functional
tks 4 help... have anyone other solution?
Click to expand...
Click to collapse
The 1.66 ROM you posted above has radio version 2.06.51.07 with it. So have you considered trying to flash that radio version and then flash the ROM. I know if you get the ROM to flash it will flash that radio anyway. But you seem to think you flashed a wrong radio so just thinking out loud here.