I attempted to use SSK 2.6 R4R Gen.Y Edition Default Kitchen from
HTML:
http://www.sskusers.net/
on my phone earlier. It seemed like everything was going fine, until I was taken to the startup screen. It was frozen, and there was red writing at the bottom of the screen.
Because the phone is stuck on that screen, when I try to connect to ActiveSync, it doesn't recognize any USB devices.
I did try removing the battery. The phone turns off, obviously, but when I turn it back on, I'm back at the frozen startup screen again.
I have also tried doing a soft reset, and the hard reset. When I do a hard reset, it takes me to the bootloader screen, and lets me do everything, but when it reboots, I just end up in the same place I was before - with a frozen startup screen.
Any suggestions on what to do, and/or what could have caused it?
Just wanted to add:
I have Verizon, and did do the hard spl using Raphael_VZW_HSPL_035, which I got from
HTML:
www.ppcgeeks.com
Reflash a different ROM through usb from the bootloader.
dwizzy130
i would suggest flashing a new rom or maybe going back to stock first & then trying a new rom. i would say the most important part right now would be flashing from the bootloader. put the nbh file on the sd card using a media reader & then pop it back in the phone & flash it. thats the easiest way & wouldn't take but 10 minutes to accomplish. i wouldn't be too worried you should be fine. feel free to get at me privately if you need some help.
Help
If you installed Hspl then just hold volume down and power and press the soft reset key. it will reboot into the bootloader and will recognize via usb. Hope this helps. I had a endless loop when i tried flashing to energyrom and this got me back to mightyrom. u may want to try it http://www.mightyrom.com
Related
I FOLLOWED all instructions for upgrade ROM and RADIO? Can one of you experts HELP? my titan keeps on rebooting and rebooting, it will not stop rebooting, PLEASEEEEEEEEEEEEEE HELP WITH INSTRUCTIONS ON HOW TO MAKE IT STOP REBOOTING.
It sounds like you might have a mismatched bootloader and ROM.
Hold down power and camera buttons while resetting. This will put you into the bootloader. What version is it?
If I am correct, IMHO the easiest way out is to load a ROM that matches your bootloader and then you will be able to connect via Active Sync once again. At that point you can start over.
Looks like JohnW on PPCGeeks had a better suggestion to upgrade the bootloader:
"Trick to load this SPL in is to
Hard reset your phone
Boot to the Wellcome screen BUT do not tap your screen
At this stage plug in your phone into your PC and apply the SPL unlocker."
I had installed Chucky rom(ChuckyROM-23136-Tabtastic.Sept.12.7z) on my htc hd2,i had also installed hspl( HSPL2_RUN.exe) around two months(in september 2010) back but i did not like it so today(25th november 2010) first i removed hspl through HSPL3_PKG.exe and put spl 2.08.0000( I DID NOT USE AN SD CARD TO FLASH THE SPL) and then flashed
Artemis_v430_0409_WWE.7z i.e RUU_Signed_0409.nbh through SSPL_RUU.exe and then it worked and was working properly but was hanging again and again so i soft reseted it two-three times and then i was installing a cab file but as soon as the installation started, it said "installation of so and so file.cab was unsuccesfull" then i tried dinik hybridia icon .cab again same thing happened so i soft reseted it and while soft reseting a complete black screen appeared and said "a program from an unrecognised software party was tried to install please press the upper volume button to reset the phone Note. you will lose all your data and the phone will completely reset itself or else press any other button to start normally" i pressed any button so it started loading normally but it has got stuck at that loading and is not doing anything after that ,
it is not connecting to the pc,the backlight of the keys is also not switching on , i have takin the video of it switching on and also of bootloader ,
what has happened to it and why is it not starting,please help?
also even after i flashed artemis gen 4 it is showing the chucky rom boot screen!
In the videos it gets stuck to where i have stopped the video and remains like that for hours(THE Video IS IN THE RAR FILE)
also i have warranty left so can i get it repaired by warranty???
PLEASE HELP ASAP
try a hard reset. turn the phone off, hold down both volume buttons, and turn the phone on, keeping the vol buttons held down. then when prompted,press vol up to reset it.
yes, you'll lose any data and modifications on your phone, it will be back to how it was right after you flashed it, but at least it will start up. better than how it is now, right?
nishankyadav said:
I had installed Chucky rom(ChuckyROM-23136-Tabtastic.Sept.12.7z) on my htc hd2,i had also installed hspl( HSPL2_RUN.exe) around two months(in september 2010) back but i did not like it so today(25th november 2010) first i removed hspl through HSPL3_PKG.exe and put spl 2.08.0000( I DID NOT USE AN SD CARD TO FLASH THE SPL) and then flashed
Artemis_v430_0409_WWE.7z i.e RUU_Signed_0409.nbh through SSPL_RUU.exe and then it worked and was working properly but was hanging again and again so i soft reseted it two-three times and then i was installing a cab file but as soon as the installation started, it said "installation of so and so file.cab was unsuccesfull" then i tried dinik hybridia icon .cab again same thing happened so i soft reseted it and while soft reseting a complete black screen appeared and said "a program from an unrecognised software party was tried to install please press the upper volume button to reset the phone Note. you will lose all your data and the phone will completely reset itself or else press any other button to start normally" i pressed any button so it started loading normally but it has got stuck at that loading and is not doing anything after that ,
it is not connecting to the pc,the backlight of the keys is also not switching on , i have takin the video of it switching on and also of bootloader ,
what has happened to it and why is it not starting,please help?
also even after i flashed artemis gen 4 it is showing the chucky rom boot screen!
In the videos it gets stuck to where i have stopped the video and remains like that for hours(THE Video IS IN THE RAR FILE)
also i have warranty left so can i get it repaired by warranty???
PLEASE HELP ASAP
Click to expand...
Click to collapse
What an utterly unfortunate situation!! Couple of questions/remarks:
1. Did you install HTC 3.14 ROM with your S/N from HTC's website before flashing Artemis?
2. You already removed HSPL, so I would advice to extract the 3.14 RUU file to your desktop and copy the custom.nbh file to your SD Card after having it renamed to leoimg.nbh (insert SD CArd into PC to do that).
3. Reinsert SD card in device and enter bootlader mode and the installation of 3.14 should start automatically.
4. After that download Artemis 43 and extract it to the folder where you're SSPL_RUU,exe resides. Bothe the custom.nbh and the SSPL file must be in the same folder!
6. Start SSPL_RUU and flash Artemis
7. After that first a hard reset and then a soft reset.
Also read page 1 - Flashing notes
This should to it for you,
regards, Kuzibri
P.S. I posted this also in Artemis thread
same problem
i've got the same problem, but i didn't install the rom artemis,
i restart the installation many time but i've got always the same problem
the display showing loading..... please wait with the chucky logo.
someone can help me???????
thank you
Hello, dear xda users. I am kinda new in Android world- i bought HTC phone month ago and i tried to get used for it. My phone is polish version of T-Mobile G2 and its called ERA G2. I rooted it, installed Amon-Ra and tried a lot of custom ROMs. After month of using different kind of Android and HTC ROMs i stayed with RCMix 2.3, because of his speed and 2.1 Sense on it. And now my problem begins:
Today my menu button stoped working in some applications so i decided to reboot device. Everything went fine with getting off, but when phone vibrated and Era initializing screen appeared, nothing happened after that.
-I tried with removing SIM, SD and all other options but still it is frozen. After couple minutes its vibrating again and restarts.
-When i plug charger for turned off phone, charging led is on but at the same time i am turning on phone, led disappears (phone is still plugged to charger).
-I cannot go to recovery by holding Home+Power... nothing happens.
-When i am holding VOL Down and Power this unknown for me HTC/Android window appears but automatically starts some kind of loading, and when its in Simlock and opening FAT32 something it restarts and Era initialization screen is on again.
-Unfortunately i dont have any warranty for this phone and i am from Poland so professional technical support is the worst way of helping for me right now.
I really enjoyed HTC Hero and i want to enjoy it more, so please if you know any way or kind of solution, please reply ; ) [sorry for my english]
Do You have adb set up?
By nothing happends You mean it wont turn on, or it wont run recovery?
Sent from my Hero using XDA App
remove battery and put it back again. This will turn off the phone. Then try Power it up. Do you get into bootloop again?
What about recovery? Replace battery and power up into recovery. 2 things might happen. You can get into your recovery normally and reflash the rom. Or you might get a screen with a phone and a big red exclamation mark. In this case you've lost your recovery and need ruu install.
brat.haneq---> i ment that i cant go to recovery- i have initialization screen and nothing happens.
So, first of all i restarted my phone a lot of times in different combinations (with SIM, without SD etc.). I cannot get to recovery when i am pressing power+home buttons and nothing happens, no exclamation mark like arvan said. I just see blue initialization screen from Era (it says Era G2 Touch)as always. Normally after some seconds it dissapears and normal bootscreen from ROM shows up, but not this time. Any thoughts?
Oh, and what is adb set up? Cheers ; )
So I guess You've really lost the recovery.... And as I said, RUU install will help...
Okay, but how i can install RUU? I tried from PC but Windows doesnt see my device... Any other option?
have you got the drivers? they come with htc sence. what does your pc see instead of hero? there might be some unknown device in the device manager if it's a driver problem.
Install RUU form SDcard (extract ROM.zip from RUU, rename it to HEROIMG.zip and put it to root of SDcard) using HBOOT mode.
There's a guide explaining the steps here http://forum.xda-developers.com/showthread.php?t=714519
A few weeks ago, I decided to install Liberated Aria. I had a few problems with the installation, but eventually it ended up working fine. Last night, I turned my phone off and turned it back on this morning, but now it won't boot. When I turn the phone on, I get:
LIBERTY PVT SHIP S-ON
HBOOT-0.57.0000
MICROP-031b
TOUCH PANEL-STN 21_00
RADIO-7.08.35.06
MAY 8, 2010,03:56:58
FASTBOOT
and then the options:
BOOTLOADER
REBOOT
REBOOT BOOTLOADER
POWER DOWN
When I try to boot into recovery, I eventually get:
SD Checking. . .
Loading . . .[LIBEDIAG.zip]
No image!
Loading. . . [LIBEDIAG.nbh]
No image or wrong image!
Loading. . . [LIBEIMG.zip]
No image!
Loading. . . [LIBEIMG.nbh]
No image or wrong image.
and the options change to:
HBOOT
FASTBOOT
RECOVERY
CLEAR STORAGE
SIMLOCK
The only problem is that I can't select any of the options. None of the buttons - volume, power, whatever - change or select anything. I can't get past either of these screens. I'm kind of a noob when it comes to this kind of thing, so any help would be appreciated.
The phone will automatically boot into FASTBOOT mode if you hold down the trackpad button while pressing the power button. Is it possible that your trackpad button is broken and is being registered as held down? Try messing with it to see if you can fix it. Otherwise you may have to get the phone replaced if it's under warranty.
This issue does not sound like it is related to installing Liberated Aria.
The trackpad button feels the same as it always has when I click it and I don't see anything visibly wrong with it, so I don't see why it would be registered it as clicked. I tried pushing it and all the other buttons a number of times with the same results. I even took off the screen protector thinking maybe that was causing a problem. Is there a way I can just put an image on my SD card and have it automatically boot that so I can fix it?
Doesn't installing a custom bootloader and/or ROM void the warranty?
Well, you probably will be able to simply run the 2.1 RUU on your phone since you can get to FASTBOOT. I'd probably recommend that over doing the SD card method because when you do the SD card method, you have to press a couple buttons to confirm actions which may not work if your phone isn't accepting button presses. The RUU method does not involve any button presses on the phone itself.
However if you want to try the SD card method I can point you in the right direction.
Edit: Link to 2.1 RUU here: http://www.mediafire.com/?cj56c2gfk86k8oe
Rohda said:
Doesn't installing a custom bootloader and/or ROM void the warranty?
Click to expand...
Click to collapse
Installing a custom bootloader would for sure, but you don't have a custom bootloader. Installing a custom ROM does, but you can reverse the process (via RUU) so they can't really tell.
I downloaded the 2.1 RUU, booted to recovery, connected my phone to my computer, and tried to run the RUU but it gave me a USB connection error. Windows also gave me a USB device not recognized error. My phone does say HBOOT USB PLUG, though. Aside from HTC Sync, do I need another driver?
Do you still have the HBOOT driver installed from when you used Unrevoked? If so you should uninstall that driver I believe. That might be interfering.
Also trying running the RUU when your phone is in FASTBOOT, not HBOOT, to see if that works.
I did have the HBOOT driver still installed. I uninstalled it from device manager and deleted the driver folders. Android Phone doesn't show up in device manager anymore. I retried running the RUU in HBOOT and tried running it in FASTBOOT and still get the USB connection error. Any other ideas?
Try reinstalling HTC sync
Sent from my Liberty using XDA App
Also try doing it on a different computer if you have access to one. Preferably one that never had any drivers on it before. Just install HTC Sync, then run the RUU, that's it.
I've always had trouble getting the RUU to run. It's bizarre.
If that doesn't work, and you still want to try the SD card method, you can download this file: http://www.mediafire.com/?ct1ay7t93d8g742
Rename the zip file to LIBEIMG.zip then place it on the SD card. Then it should automatically detect the file next time you're in HBOOT and ask you if you want to proceed with the install. It's pretty self explanatory. Be patient as some steps take a while and it may appear like nothing is happening. It takes about 5 minutes to finish installing everything and will reboot once during the process. After it's done (it will tell you when it's done), the phone will reboot and there will be a scary looking screen but JUST WAIT about 10 seconds and it will boot normally. Then you're good to go.
After you're done with this, make sure to DELETE the LIBEIMG.ZIP file from your SD card. Otherwise it will ask you every time you go into HBOOT if you want to apply the update.
I reinstalled HTC Sync and it wouldn't recognize the phone was connected.
It seems to have taken a turn for the worse. Now, it won't even turn on. The screen turns on (but stays black) and off and the notification light flashes red when connected to a computer but won't do anything at all when it's not connected. I'll try to plug it into a wall instead of a computer and let it charge for a while and try the SD card method.
I went in today to get it checked out and got a new SIM card and a new battery and it fixed the problem.
Thanks a ton for all the help.
Hi
I used the factory reset function on my tab a couple days ago to delete all apps and such and upon reboot it was stuck at the slowly flashing Samsung logo and would proceed no further. I left it for a good hour and a half in that state before I tried hard resetting it but no dice. I've had it do this before when I first rooted it, but unlike that time it doesn't replay the whole boot animation, just the logo part at the end of the animation. I managed to get it in clockwork mod or bootloader whatever that function is and cleared all the caches and did a reboot recovery (i believe thats what it was called) but upon reboot it did the same exact thing. So after that I gave up and went to bed, but the next day when I went back at it again it wouldn't even turn on. After messing around with the power button and volume button trying to get into recovery mode it finally turned on but went to the battery screen with no other actions. I've tried several times to get it into recovery mode but it either wont turn on or it just goes to the battery screen. I have it plugged into my pc at the moment and apparently it is in recovery mode or something because Odin recognizes it. Says [0:COM3] and the box is yellow, but the screen never turns on though when holding the power button and volume button while it's plugged into a pc, the pc recognizes something plugged into the USB slot. My pc is only recognizing it as a modem and will do nothing else with it.
I have the Starburst rom and the overclocked kernel installed and would like to either revert it to stock rom or perhaps the AOKP rom, milestone 6. Is there any way to do this if I can't boot it into a state where I can access the SD card on my pc? All the guides I've found always require I put files on the sd card to flash in clockwork recovery mod. Thanks for any assistance
Edit: Solved it myself, feel free to delete this post. Thanks!