I had installed Chucky rom(ChuckyROM-23136-Tabtastic.Sept.12.7z) on my htc hd2,i had also installed hspl( HSPL2_RUN.exe) around two months(in september 2010) back but i did not like it so today(25th november 2010) first i removed hspl through HSPL3_PKG.exe and put spl 2.08.0000( I DID NOT USE AN SD CARD TO FLASH THE SPL) and then flashed
Artemis_v430_0409_WWE.7z i.e RUU_Signed_0409.nbh through SSPL_RUU.exe and then it worked and was working properly but was hanging again and again so i soft reseted it two-three times and then i was installing a cab file but as soon as the installation started, it said "installation of so and so file.cab was unsuccesfull" then i tried dinik hybridia icon .cab again same thing happened so i soft reseted it and while soft reseting a complete black screen appeared and said "a program from an unrecognised software party was tried to install please press the upper volume button to reset the phone Note. you will lose all your data and the phone will completely reset itself or else press any other button to start normally" i pressed any button so it started loading normally but it has got stuck at that loading and is not doing anything after that ,
it is not connecting to the pc,the backlight of the keys is also not switching on , i have takin the video of it switching on and also of bootloader ,
what has happened to it and why is it not starting,please help?
also even after i flashed artemis gen 4 it is showing the chucky rom boot screen!
In the videos it gets stuck to where i have stopped the video and remains like that for hours(THE Video IS IN THE RAR FILE)
also i have warranty left so can i get it repaired by warranty???
PLEASE HELP ASAP
try a hard reset. turn the phone off, hold down both volume buttons, and turn the phone on, keeping the vol buttons held down. then when prompted,press vol up to reset it.
yes, you'll lose any data and modifications on your phone, it will be back to how it was right after you flashed it, but at least it will start up. better than how it is now, right?
nishankyadav said:
I had installed Chucky rom(ChuckyROM-23136-Tabtastic.Sept.12.7z) on my htc hd2,i had also installed hspl( HSPL2_RUN.exe) around two months(in september 2010) back but i did not like it so today(25th november 2010) first i removed hspl through HSPL3_PKG.exe and put spl 2.08.0000( I DID NOT USE AN SD CARD TO FLASH THE SPL) and then flashed
Artemis_v430_0409_WWE.7z i.e RUU_Signed_0409.nbh through SSPL_RUU.exe and then it worked and was working properly but was hanging again and again so i soft reseted it two-three times and then i was installing a cab file but as soon as the installation started, it said "installation of so and so file.cab was unsuccesfull" then i tried dinik hybridia icon .cab again same thing happened so i soft reseted it and while soft reseting a complete black screen appeared and said "a program from an unrecognised software party was tried to install please press the upper volume button to reset the phone Note. you will lose all your data and the phone will completely reset itself or else press any other button to start normally" i pressed any button so it started loading normally but it has got stuck at that loading and is not doing anything after that ,
it is not connecting to the pc,the backlight of the keys is also not switching on , i have takin the video of it switching on and also of bootloader ,
what has happened to it and why is it not starting,please help?
also even after i flashed artemis gen 4 it is showing the chucky rom boot screen!
In the videos it gets stuck to where i have stopped the video and remains like that for hours(THE Video IS IN THE RAR FILE)
also i have warranty left so can i get it repaired by warranty???
PLEASE HELP ASAP
Click to expand...
Click to collapse
What an utterly unfortunate situation!! Couple of questions/remarks:
1. Did you install HTC 3.14 ROM with your S/N from HTC's website before flashing Artemis?
2. You already removed HSPL, so I would advice to extract the 3.14 RUU file to your desktop and copy the custom.nbh file to your SD Card after having it renamed to leoimg.nbh (insert SD CArd into PC to do that).
3. Reinsert SD card in device and enter bootlader mode and the installation of 3.14 should start automatically.
4. After that download Artemis 43 and extract it to the folder where you're SSPL_RUU,exe resides. Bothe the custom.nbh and the SSPL file must be in the same folder!
6. Start SSPL_RUU and flash Artemis
7. After that first a hard reset and then a soft reset.
Also read page 1 - Flashing notes
This should to it for you,
regards, Kuzibri
P.S. I posted this also in Artemis thread
same problem
i've got the same problem, but i didn't install the rom artemis,
i restart the installation many time but i've got always the same problem
the display showing loading..... please wait with the chucky logo.
someone can help me???????
thank you
Related
I've tried a search but couldn't find anything that'd help me so...
I've just flashed my phone and it completed fine, rebooted and stuck on the first splash screen. Tried a soft reset and it stuck on the Windows Mobile splash screen, 5 mins later it's still there...
I've got HardSPL7 installed, so how can I flash the previous Rom I was using back onto the phone?
Ta
Off to have another search while I wait
Copy your chosen ROMs .nbh file to the root of your SD card and rename it to hermimg.nbh. Reset device in to bootloader and it should detect the hermimg.nbh and instruct you to press ther Power buton to update. Sometimes you need to go into bootloader a few times before it picks it up.
See WIKI here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing
It is a good thing you have HardSPL v7 installed.
When this happened to me a while back, the best way to recover for me was to extract and copy the OS's .NBH file to the root of my SD card (formatted as FAT32) and naming it HERMIMG.NBH.
If you go into the boot screen (Pwr + OK + SR), you will get a prompt to start flashing the image. After the flash, my device was OK.
I am now using this method every time I flash my OS.
EDIT: Seems Maaron beat me to it.
Thanks guys, now re-flashing to my previous rom.
Was surprisingly easy
Yeah it was lucky I've got HardSPL, glad I put it on
Again ta for the hlep
I first used the SD method to fix a bad flash but now I use it evey time. It seems to flash much quicker this way and it doesn't matter what OS you have on your PC, whether you have incompatible USB controller, version of Activesync etc etc...
Had to do the radio the same way as it still wouldn't boot, but now back in action.
Ta
Good thread w/ information. I too am glad that I flashed HardSPL on my device as well
Out of interest, does the SD card have to be blank except for the image? Or can I just bung the .nbh on there and flash with loads of other stuff on the card?
Ta
The WIKI mentions to copy the nbh file on to a blank SD card but I have found it to work on my card containing numerous files and folders as long as it is in the root of the card.
I have tried that wicki (I was using schnaps and it has for some reason failed on booting after 2 weeks working fine...)
When i press the ok, power and reset buttons it takes me to a screen with red/green/blue/white bars (4 of them) showing
HERM100
IPL-1.04
HERM100
SPL-1.40.Olipro
I have done a flash of the SPL to http://www.mrvanx.org/cms/index.php...ask=view&id=38&Itemid=26&limit=1&limitstart=2
I did this and it said it was successful 2 weeks ago!
What can I do? Help!!!
EDIT: Did a hard reset by pushing the button above the start button, button above the ok button and hitting the reset with the stylus. This seems to have fixed the issue, but what worries me is that apparently hardspl v7 is not on there! :|
I FOLLOWED all instructions for upgrade ROM and RADIO? Can one of you experts HELP? my titan keeps on rebooting and rebooting, it will not stop rebooting, PLEASEEEEEEEEEEEEEE HELP WITH INSTRUCTIONS ON HOW TO MAKE IT STOP REBOOTING.
It sounds like you might have a mismatched bootloader and ROM.
Hold down power and camera buttons while resetting. This will put you into the bootloader. What version is it?
If I am correct, IMHO the easiest way out is to load a ROM that matches your bootloader and then you will be able to connect via Active Sync once again. At that point you can start over.
Looks like JohnW on PPCGeeks had a better suggestion to upgrade the bootloader:
"Trick to load this SPL in is to
Hard reset your phone
Boot to the Wellcome screen BUT do not tap your screen
At this stage plug in your phone into your PC and apply the SPL unlocker."
hi,
i've searched, and am stuck. i tried to flash a new ROM today, but it stopped at 76% and said no connection!?? i've flashed before with no problems many ROMs. I have HardSPL 1.15 mfg installed and everything always worked. Now i'm stuck at 4 color boot screen screen. HardSPL is still there, there is a message at top right saying 'RUUNBH'. I plug USB in and it says 'USB'. I run mtty but can't seem to get any CMD, or even type 'boot' in, no response on app, running on XP?
i'm reeally stuck, and had to come to work, so am worried. can anyone help??
sorry, i am still searching for solution, but please any help appreciated!!
thank you
i will try to check back often, but stuck at work might be problem ..
i got stuck at that boot screen too, but it happened during a boot image change operation. All I had to do was install a new rom.
Hope it helps...
how did you install a new rom? cos i cant activesync, and running CustomRUU.exe says it cant find pda device
am i bricked? really stuck here :'(
badaas said:
how did you install a new rom? cos i cant activesync, and running CustomRUU.exe says it cant find pda device
am i bricked? really stuck here :'(
Click to expand...
Click to collapse
Don't worry, you just need to get to the bootloader screen and flash again, you may have a corrupted update that may hault everytime. If it doen't work try another ROM.
Hold down power and the camera button while pressing and holding the reset button.
When you see the Boot Loader screen you can release all three.
Plug in your cable if it is not already, wait to make sure the computer installs the device and then run the ROM Update executable you want or ROMUpdateUtility.exe if everything is placed in a folder.
Note: Activesync and Mobile Device Center will not launch in this mode, and if the utility tells you to connect through activesync or Mobile Device Center ignore and continue.
OK thank you my friends, i will try when i get home from work. fingers crossed!!
cheers
thx guys, all sorted
I attempted to use SSK 2.6 R4R Gen.Y Edition Default Kitchen from
HTML:
http://www.sskusers.net/
on my phone earlier. It seemed like everything was going fine, until I was taken to the startup screen. It was frozen, and there was red writing at the bottom of the screen.
Because the phone is stuck on that screen, when I try to connect to ActiveSync, it doesn't recognize any USB devices.
I did try removing the battery. The phone turns off, obviously, but when I turn it back on, I'm back at the frozen startup screen again.
I have also tried doing a soft reset, and the hard reset. When I do a hard reset, it takes me to the bootloader screen, and lets me do everything, but when it reboots, I just end up in the same place I was before - with a frozen startup screen.
Any suggestions on what to do, and/or what could have caused it?
Just wanted to add:
I have Verizon, and did do the hard spl using Raphael_VZW_HSPL_035, which I got from
HTML:
www.ppcgeeks.com
Reflash a different ROM through usb from the bootloader.
dwizzy130
i would suggest flashing a new rom or maybe going back to stock first & then trying a new rom. i would say the most important part right now would be flashing from the bootloader. put the nbh file on the sd card using a media reader & then pop it back in the phone & flash it. thats the easiest way & wouldn't take but 10 minutes to accomplish. i wouldn't be too worried you should be fine. feel free to get at me privately if you need some help.
Help
If you installed Hspl then just hold volume down and power and press the soft reset key. it will reboot into the bootloader and will recognize via usb. Hope this helps. I had a endless loop when i tried flashing to energyrom and this got me back to mightyrom. u may want to try it http://www.mightyrom.com
I've got a jamin in 3color screen i've tried to update it with shiped rom it runs without any error and gives congratulation msg but the screen is still on bootloader after updating the progress bar runs normal. when i do hard reset it freezed on start logo.
pls help anybody if possible
regards
you want the original rom from i-mate to setup in your pocket pc because your phone is locked with security you shoud make HardSPL to setup any rom on your phone
azhar63 said:
I've got a jamin in 3color screen i've tried to update it with shiped rom it runs without any error and gives congratulation msg but the screen is still on bootloader after updating the progress bar runs normal. when i do hard reset it freezed on start logo.
pls help anybody if possible
regards
Click to expand...
Click to collapse
try a hard reset (hold camera and comm manager and power) it will powers up telling you that it will format the drive.
press yes (green call key) then see if it will boot up
if not:
then do the following
http://forum.xda-developers.com/wiki/index.php?title=Prophet_recovery