Hi, got problem and need your HELP!
EDITED:
I was trying to set my raph to stock, cuz warranty.
But, after flashing stock SPL, it goes to bootloader write :
" Upgrade rom code error, please try again"
What was happend:
1)I forgot to flash back stock Radio, so... my Raphael now stay in bootloader. And write "Upgrade ROM code error, please try again".
2)I was tried to flash stoc SPL via SD card. maybe it is problem.
What was I try:
I tried to flash HardSPL, but it stuck on 0%
I tried to flash stock Radio, but it stuck on 0%
I tried to flash stock ROM , but it stuck on 0%
I tried to flash non-stoc ROM, and it writes "Invalid vendor ID" or somethink like that, its cuz I have stock SPL, right?
What next?
SOLVED
!! If you will try this way it is on your own risk !!
Here is how to solve this issue:
1) Download MTTY 1.42
2) Download ActiveSync Drivers
3) Download STOCK ROM for your phone(best is from you provider or seller web site)
4) Install drives and disable USB connection in ActiveSync and reboot your computer
5) Set your phone to bootloader and connect via USB
6) Open MTTY set connection to USB
7) Send command "set 16 0" in mtty (without the quotes)
8) Reboot your phone and set it again to bootloader
9) Allow USB connection in ActiveSync and run RUU with stock Rom and Radio
10) If flash is done, make hard-reset
11) You are done!
!!This comes with no gaurentee!!
I cant find way out of this issue
Maybe mtty can help, but I dont know what was write as commands.
A few members have run into that issue before.
Before MTTY, I recommend posting in the HardSPL thread to see if such a member can share some insights.
Cheers,
thx, hope they help me.
EDITED ! new facts !
MiTMaNeK said:
Hi, got problem and need your HELP!
EDITED:
I was trying to set my raph to stock, cuz warranty.
But, after flashing stock SPL, it goes to bootloader write :
" Upgrade rom code error, please try again"
What was happend:
1)I forgot to flash back stock Radio, so... my Raphael now stay in bootloader. And write "Upgrade ROM code error, please try again".
2)I was tried to flash stoc SPL via SD card. maybe it is problem.
What was I try:
I tried to flash HardSPL, but it stuck on 0%
I tried to flash stock Radio, but it stuck on 0%
Click to expand...
Click to collapse
As far as I know, HardSPL and the stock SPL cannot be flashed via SD card. You must use the .exe file that you download with HardSPL. I believe that the first post of the HardSPL thread says something to that effect. Flashing the stock SPL should always be done LAST, so flash your stock ROM and Radio (if the ROM does not include the Radio). If your phone is stuck in bootloader, you should still be able to flash your device. See this thread for more information about flashing back to stock SPL.
htcfan78 said:
As far as I know, HardSPL and the stock SPL cannot be flashed via SD card. You must use the .exe file that you download with HardSPL. I believe that the first post of the HardSPL thread says something to that effect. Flashing the stock SPL should always be done LAST, so flash your stock ROM and Radio (if the ROM does not include the Radio). If your phone is stuck in bootloader, you should still be able to flash your device. See this thread for more information about flashing back to stock SPL.
Click to expand...
Click to collapse
Yea, I know it now too HardSPL and stock SPL only via cable.
Yea, Im able to flash, but it every time stuck on 0%
And if i try to flash ROM what isnt for my Rahp it write "invalid vendor id", its because I got stock SPL and I cant find way how to flash HardSPL - normal way isnt working for me.
I dont know if what i have in mind will fix it - or possibly make it worse! so i wont post it here (in case someone else mistakes it for propper advice!) but check your PM - and remember it comes with no gaurentee!
SOLVED !
BIG THX TO Beeble !
Thx for the tip that info was very important for me...
Related
A wrong D600 rom is flashed into my D600, and now it stop at the first splash image and never go further.
I've tryed these below but none helps.
1. Reformat ROM by hold the left & right button then reset.
2. Enter bootloader and flash any rom that I've flashed before, but they all aborted at 2% and then reboot.
3. Dump a os.nb & a extrom.nb from a never flashed D600, and generate a nbh and flash, the result is the same as 2.
The SPL version of my D600 is 1.03.000, and I use the jumpspl to flash a rom before, but now I can not enter the system in the phone and can not run jumpspl anymore.
I thought the key point is that some number or value in these roms are not correct. I've tried both GENE10000 as Model ID, 11111111 as Country ID, 1.00.000.0 as Version, WWE as Language and GENE10000 as Model ID, SuperCID as Country ID, 1.00.000.0 as Version, CHS as Language.
I found an article (http://www.aray.cn/archives/1687 in Chinese) that said there is a list to modify the nbh by model and spl version, but I cannot find the list.
Any help is greatly appreciated!
D600
plz, download any version of ROM as WWE, then connect your device with computer, enter BOOT LOADER, then just click the RUU.exe files, your device will formatted, think it will help you..
Download Link:-
http://forum.xda-developers.com/showthread.php?t=381048
thank you for your help
I've tried that, but it didn't solve the problem. RUU got an error code 270 at progress 2% and my phone then reboot.
I forgot to write that RUU report error code 270 when flashing any rom at progress 2%.
I also tried to flash via sd card
but an error message "invalid certificate" got when checking sd contents
how to flash using SD card
xeroo said:
I also tried to flash via sd card
but an error message "invalid certificate" got when checking sd contents
Click to expand...
Click to collapse
Could you please explain how to flash by sd card
Well, just put the rom in your sd card with the name GENEIMG.nbh at the top level
Reboot into the bootloader, it will start automaticlly
Your sd card must be fat32 fs type.
xeroo said:
Well, just put the rom in your sd card with the name GENEIMG.nbh at the top level
Reboot into the bootloader, it will start automaticlly
Your sd card must be fat32 fs type.
Click to expand...
Click to collapse
Thank you for sharing , but my phone didn't responded to it.
Anyway did you try to gene_cert_fix to fix certificate issue of rom before flashing
It is said that not all gene phone will act, but most do.
I havn't tried the gene_cert_fix.
I found one via google and I'll try it later.
Thank you a lot!!!!
xeroo said:
A wrong D600 rom is flashed into my D600, and now it stop at the first splash image and never go further.
I've tryed these below but none helps.
1. Reformat ROM by hold the left & right button then reset.
2. Enter bootloader and flash any rom that I've flashed before, but they all aborted at 2% and then reboot.
3. Dump a os.nb & a extrom.nb from a never flashed D600, and generate a nbh and flash, the result is the same as 2.
The SPL version of my D600 is 1.03.000, and I use the jumpspl to flash a rom before, but now I can not enter the system in the phone and can not run jumpspl anymore.
I thought the key point is that some number or value in these roms are not correct. I've tried both GENE10000 as Model ID, 11111111 as Country ID, 1.00.000.0 as Version, WWE as Language and GENE10000 as Model ID, SuperCID as Country ID, 1.00.000.0 as Version, CHS as Language.
I found an article (http://www.aray.cn/archives/1687 in Chinese) that said there is a list to modify the nbh by model and spl version, but I cannot find the list.
Any help is greatly appreciated!
Click to expand...
Click to collapse
那个是骗人的，换字库吧呵呵。
Xeroo, is your provlem being solved?
Hi. How to flash a new rom to niki100 ?
Plugin the USB cable into your device and PC, start the Update.exe and wait until it's finished!
If you stuck in the bootloader, simply flash an original Provider ROM like from T-Mobile or whatever you use! After that, flash HardSPL (read the sticky!!!) and try it again!
To flash a ROM, you don't need ActiveSync running!!!
Do I need to run any other program before I flash a new ROM or can I just basically flash it straight with the default HTC setup running?
squire
squire23 said:
Do I need to run any other program before I flash a new ROM or can I just basically flash it straight with the default HTC setup running?
Click to expand...
Click to collapse
If you are just flashing the official ROMs, then just follow the links from your phone company or HTC. Download the ROM and run it on your PC.
If you want to flash custom ROM, then more work is needed:
1) Make sure phone is unlock
2) HardSPL the phone to protect the bootloader from being overwritten
3) Download and flash the custom ROMs.
Hi!
I've a big problem with my new Evo3D GSM!
After installing my first custom rom (http://forum.xda-developers.com/showthread.php?t=1318942) the wifi goes in error, like some persons here. So, I would like to revert to officiel rom but I can't!
If I launch RUU with my phone is on Android, RUU can't launch bootloader (Error 155), and I try to put my phone into fastboot mode, then RUU begin but error 155 again during sending data :-/
Apparently, the image was wrong... but it's the official ruu, and I've already flash this before S-Off!!
Please help!!
This is what I've do on my phone : (at beginning, I've original rom, with update OTA and S-On)
- Install official ruu RUU_Shooter_U_HTC_Europe_1.20.401.2_Radio_10.53.90 20.00_10.13.9020.08_2M_release_203403_signed
- Unlock with htcdev.com
- Install CWM
- Install custom rom
How can I flash official rom again?
Thanks in advance!!
//Edit : Success!!!! Just need to relock the phone! lol... Maybe this post can be useful for someone... ^_^
Hi! I've managed to brick my device (d610ar) badly, i think
the device doesn't boot normally (message "Secure booting error! Cause: boot certification verify.", and i am stuck there), can't charge it with the wall charger, and the only thing that works is download mode; but flashing a kdz with LG FlashTool (the way i went back to stock a few times) says flashing and at 2% (or 3% sometimes) it says that doesn't find the device, that i have pull out the battery to reconnect my device again and when i do that it does the same thing on a loop, asking to do it again later..
the funny thing is that it appears on device manager on windows, on com port 11 for example, but the FlashTool doesn't recognize it..
so, i can't flash any kdz and doesn't boot.. i've read around here in xda to enter fastboot to fix it, but.. can this device enter fastboot? i couldn't do it, tried adb too and couldn't make the device visible..
i, before this happened, had multirom installed, rebooted to recovery and deleted secondary roms to install in primary rom cm12.1.. there started to happen strange things when rebooted normally to configure it..
after a while trying to boot found around here in xda too that i could enter twrp recovery via hardware keys to reinstall again, so got into it and installed a flashable zip to come back to stock KitKat directly, that have worked for me before..
after that rebooted and i can't do anything else than download mode..
i kinda figured that the problem must be that multirom injected the boot sector after installing the stock flashable zip, and when i did that restored the stock aboot and abootb (these, modified carefully, allowed us to unlock bootloader and flash recoveries, etc, etc.. ; by the way, many thanks to the devs that discovered it and made the guides!)..
now i have read the instructions for flash via fastboot the stock boot.img and so pass the security verification, but i can't enter it..
so, what do you think that could be the next step? or is it really hard bricked and i should forget about it? i'm really hoping to recover it but i don't know what else to do..
sorry for the bad english, not my primary language
thanks for reading and i am hoping to hear some suggestions!
He is not hard bricked you need to flash stock boot and reunlock bootloader if you have custom recovery still installed, but go first with the eazy way search xda about lg flash tool stuck at 2% there some guides to help you get kdz flashed
Thank you very much!
numpea said:
He is not hard bricked you need to flash stock boot and reunlock bootloader if you have custom recovery still installed, but go first with the eazy way search xda about lg flash tool stuck at 2% there some guides to help you get kdz flashed
Click to expand...
Click to collapse
Thank you very much! You made me realize why wasn't working..
Because of you, i started to search threads related with the "flashtool stuck at 2%" and one of the things to look at was a txt file to see what was the problem.. there i found out that the lg FlashTool recognized my device as LGD618..
That's when i realized that i must've messed up when i flashed a lollipop flashable zip for the D618(a while ago), "converting" my cellphone on that model.. so when i connected on download mode and put the LGD610 kdz the comparison of cellphone model and binary model didn't match..
Solution was to flash LGD618 kdz, boot up normally, install towelroot, install supersu, edit a line on build.prop
from persist.multisim.config=dsds to persist.multisim.config=none
rebooted and that's it.. everything works perfectly now! i won't be doing stuff to it for a while
probably will stay stock like that, because now i will be using an OnePlus One in a few days and the G2 mini will be used by my mother, i think..
Thanks again! You saved my device for being bricked forever
i glad i could helped you :good:
I tried installing kitkat having installed lollipop and did not work, also I tried installing lollipop and nothing. Well I think this update lollipop are adding some kind of lock to disallow downgrade or upgrade by KDZ. I try other methods, unlocking bootloader, and install a aboot.img, bricked my phone. I recommend that you do not attempt to unlock the bootloader and install any system image that is not official, or may end up with a dead device.
Hey Guys,
i spent the last 8 hours to get my z back to life but without luck.
i was on aokp (official) as i decided to go back to stock rom, after i have seen that my device wouldnt boot a normally after the first flash, i flashed lineage os and from there it always tells me that it needs a password to start android. but i never had a passwort so i tried the one from my google account but it doesnt worked.
and now im stuck on the warning screen from the unlocked bootloader i can still go in recovery / bootloader mode but it doesnt matter what i flash it wont work.
SO PLEEASE HELP ME... i can give a small donate via paypal if you can help me the right way!
Hi.
You still have access to TWRP? if yes go to Advanced > File Manager then navigate to this path: /data/system
Look for this files:
password.key
pattern.key
locksettings.db
locksettings.db-shm
locksettings.db-wal
Delete them all. if one or two of them is not exist that's Ok, skip them.
Now reboot the phone and see the password request form appears or not.
P.S. Don't panic you not bricked your phone.
Hello and thank you for your answer. But i do not have this files.
in data/system/ i have 3 ordners "dropbox-add" "heapdump" and "perfd".
nexxer92 said:
Hello and thank you for your answer. But i do not have this files.
in data/system/ i have 3 ordners "dropbox-add" "heapdump" and "perfd".
Click to expand...
Click to collapse
Then i suggest try a full wipe.
Dalvik
Catch
Data
System (By wiping this partition hole android OS will remove)
after that try to flash an custom ROM (Lingoes, RR, orginal images)
I hope this will solve the problem.
Soo, after a full night of flashing ( im seriously feeling like a pro hacker with all those command windows open ) i have managed to get back to stock reteu wit november security patch and relocked bootloader.
The only thing which bothers me at the moment is when i start the phone normally it takes me directly in the fastboot menu, but the screen for bootloader unlock is gone and it still says status: modified.
How is it possible that the phone boots normally? And can i do OTA Updates now with relocked Bootloader?
Thanks in advance!
nexxer92 said:
Soo, after a full night of flashing ( im seriously feeling like a pro hacker with all those command windows open ) i have managed to get back to stock reteu wit november security patch and relocked bootloader.
The only thing which bothers me at the moment is when i start the phone normally it takes me directly in the fastboot menu, but the screen for bootloader unlock is gone and it still says status: modified.
How is it possible that the phone boots normally? And can i do OTA Updates now with relocked Bootloader?
Thanks in advance!
Click to expand...
Click to collapse
How did you do that. I'm trying and trying to get back to stock EU firmware. No chance, I always get verification problem, need signed boot bla bla.
Btw. For normal boot try this
fastboot oem fb_mode_clear
knjigo said:
How did you do that. I'm trying and trying to get back to stock EU firmware. No chance, I always get verification problem, need signed boot bla bla.
Btw. For normal boot try this
fastboot oem fb_mode_clear
Click to expand...
Click to collapse
hi
i flashed an RETBR Firmware.. bootet it, installed update.zip to 7.1.1 with adb sideload and then flashed again with fastboot oem lock begin.
nexxer92 said:
hi
i flashed an RETBR Firmware.. bootet it, installed update.zip to 7.1.1 with adb sideload and then flashed again with fastboot oem lock begin.
Click to expand...
Click to collapse
Great for you. Where did you get update to 7.1.1?
I get always error not signed boot.
If you could provide some step by step manual how to flash stock rom and relock bootloader it would be great.
I was also on reteu german firmware.