Related
Alright so here is the premise. I had a good ol time trying to figure out what to download and where to go, what to do, etc, so i thought i would give anyone interested a step by step tutorial (only for you alltel people, vzw can fend for themselves). Please read all the instructions before you do anything, i can jump around a bit sometimes.
Yes, this should enable your GPS and Rev A. No, I will not be responsible if you destroy you phone (although highly unlikely...)
1. download the newest bootloader.
1a. file can be found here
1b. install the bootloader.
1c. this opens up a dos prompt. read it carefully and make sure your phone is already connected when you open the application.
1c. i believe the second time it asks you to "press a key to continue" you need to disconnect your phone and plug it back in. it tells you to do this so just read the directions.
1d. if it reads out that your phone cant be contacted and to check your cable, its probably because you didnt do step 2b.
2. download and install the new radios.
2a. Dont freak, we are going to download a sprint rom.
2b. Download it from here
2c. Run the exe with your phone plugged in.
2d. IMPORTANT: Once the flash is done, the phone will boot up. It will ask you to tap the screen to begin. If you tap, you Fail. Dont tap the screen.
2e. Move to step three.
3. Almost there, now we are getting a good ol' cooked ROM to run on it.
3a. Download DCD's kitchen here. You will also need to download Visual C++ and .Net Framework from here and here
3b. Once downloaded, click on build rom, you will see a bunch of fancy command prompt windows. Just let it sit there for a while. You will see a window come up with a bunch of check boxes. Really click whatever you want. The default selections should be enough to satisfy you. The only thing you need to make sure to do is click on "Alltel" in the carrier screen and click off of "Sprint", the default.
3c. Once you have selected what you want (again I encourage to just use the defaults and maybe add office or entertainment or something), then click the play button at the top. Once the window shows its done loading, click the x to close out of the builder. The command prompt window will start spewing information again at you. Disregard that, its not really vital.
3d. After the command prompt finishes the tizzy it got itself into, the HTC flashing application will automatically launch. Follow through in this window and it will eventually flash you phone. Thats really all you have to do!
Final Thoughts: This guide will also work with any of the other carriers that DCD's new kitchen supports. Thats pretty much everyone because, he is, you know, the man and all. The only thing you have to change is the selection of you carrier when you are "building" your rom. For the specifics of this guide I choose alltel but you can use whatever you want assuming it matches your carrier.
Please write down your Programming information before you do this flash. And its important to know your MSL if you have one of those BS carriers that changes it (unlike alltel). If you need to reprogram your phone, dial ##000000+send and put in your nam information. If you need to still set you A-Key or HDR password (more advanced stuff, the A key allows some sort of authentication and HDR password (located in the security section) allows you to connect to EVDO networks) then you can access the more advanced EPST menu with ##778+send.
Make sure you update with *228 to get the latest PRL or search around online.
Happy Flashing!
Feel free to send me a message if you have any questions or if i left something out
ALSO THANKS TO EVERYONE WHO MADE THIS POSSIBLE AT XDA, GREATEST PHONE SITE IN EXISTENCE
Finally, a step by step for Alltel folks...Thanks. My head was spinning trying to piece together everything from all the various posts.
Terrific write up.
If you can, include where to find the MDN, MSID, and AKEY before upgrading so that these can be re-installed if erased...
Old roms don't work
Nice guide, but you should also note that older roms have a compatibility issue with the new radio upgrade. it seems right now only dcd's cooked rom works; for me at least.
The information you are looking for can be found by using the advanced EPST feature in the phone. assuming you are using a stock dialer (or one that supports codes) inut "##778" and then press call. it will bring up a menue and ask to view or edit. If you are getting your info, of course, press view and if you are replacing info, just click edit. all the info like your mdn and min (which you should know without having to look in here) will be here. clicking the menu on the taskbar will let you choose an entire metric ****ton of info to view. a key is one of them. I noticed now that going back, my akey is not inputted. i dont know what this value is but in the past i think i have seen it as just "0" or blank. I was foolish and didnt write it down before the flash. if anyone has anything diferent in their akey, wanna post it?
update prl
alright so i think i solved the problem with the roaming issue and the EVDO connectivity. and i feel like an idiot. for some reason i just kept on putting off updating the prl since i flashed it. and for another reason i didnt think it would matter. but i have since used the latest prl and updated completely and, wouldntyouknowit, it works perfect. steps?
1. download the newest prl here.
2. bluetooth or copy to your phone
3. open the dialer and press "##775" (this spells prl)
4. enter your unlock code, should be 000000
5. click on update prl, then menu at the bottom then edit
6. browse to where the prl is on your phone (probably my docs if you BTed it)
7. update and restart, voila!
8. enjoy having EVDO and no triangle again! WOOT!
just wondering, after following through all those steps, do we need to relock it?
Also want to note that, this method does indeed work for all providers (alltel, vzw, sprint), it's just the step where you have to flash your rom (DCD's or any other) make sure it is the one with your provider. I made a mistake of downloading the Alltel rom when I'm really a Sprint user :x.
Have any of you folks been able to get OfficeSync to work with this ROM? I can surf the web but am unable to register with my account.
I was hung up in between steps 2 and 3. The screen was stuck on the Alltel screen and I couldn't connect with my pc to install the ROM. I followed other instructions to use a FAT32 formatted SD card with the ROM renamed to TITAIMG.nbh. Reset into bootloader mode by holding the power and camera buttons and hard reset. Run the setup from there... Hope this helps someone else.
Total_Lag said:
just wondering, after following through all those steps, do we need to relock it?
Also want to note that, this method does indeed work for all providers (alltel, vzw, sprint), it's just the step where you have to flash your rom (DCD's or any other) make sure it is the one with your provider. I made a mistake of downloading the Alltel rom when I'm really a Sprint user :x.
Click to expand...
Click to collapse
I never locked my phone and it works fine. So I am guessing no, you dont. And yeah you are correct it should work fine with any of DCD's roms, i just know the alltel one was a success for me, didnt want to lead someone astray. I know the telus one, for example, was bugged at first. idk
This is my first modification to my cell phone...just got it! Is there a setting I check to verify the GPS is working? I just looked around and all I saw were settings for connectiong external GPS devices. Also, when i go to communications manager...there is no setting for GPS. Shouldn't there be a way to turn GPS on and off? Thanks for the help!
Ok....I don't think mine is working because I installed Google Maps and clicked track location and it just stayed at Contacting Satellites (0)...I think I may have messed it up because I installed the SPL first, then the DCD's OS and last the radios...i went back and tried to reinstall everything int he correct order, but now the radio ROM says it's not created for my device.
Is there a way to start over with a fresh install so I can try this again and do it in the correct order this time? Please help! Thanks!
Well im having problems. I installed the new rom via sd card. Everything seemed to go smooth, but when wm starts up and goes through the align screen thing it just restarts and never starts up.
bond00 said:
Ok....I don't think mine is working because I installed Google Maps and clicked track location and it just stayed at Contacting Satellites (0)...I think I may have messed it up because I installed the SPL first, then the DCD's OS and last the radios...i went back and tried to reinstall everything int he correct order, but now the radio ROM says it's not created for my device.
Is there a way to start over with a fresh install so I can try this again and do it in the correct order this time? Please help! Thanks!
Click to expand...
Click to collapse
If you want to start from a blank slate you should be able to install a factory ROM and then begin again from there. It's my understanding that the proper order should be: New SPL --> DCD's ROM --> New Radio
I myself, when following this order, got stuck at the Alltel splash screen after I installed DCD's ROM, but before installing the radio. A reboot with the camera and power buttons held down simultaneously got me into bootloader. From there the ROM installer could recognize the device and proceed with the radio install.
If you click on the data arrow icon at the top, what does it say?
Mine says:
"Alltel Wireless (Dial-up) Connected"
I cant remember before what it said when connected but my download high was 497kps & 97kbps for upload. Either the area I am in doesnt have Rev A (Which I think is the case based upon EVDOMAPS) or my data connection is now hindered...
xweaponx said:
If you click on the data arrow icon at the top, what does it say?
Mine says:
"Alltel Wireless (Dial-up) Connected"
I cant remember before what it said when connected but my download high was 497kps & 97kbps for upload. Either the area I am in doesnt have Rev A (Which I think is the case based upon EVDOMAPS) or my data connection is now hindered...
Click to expand...
Click to collapse
I personally have not been able to reach an EVDO signal at all. in an area where i was always at EVDO, now im mostly shown as roaming and in 1x. I have most recent prl and my SIDs are correct. i think there is a reason this rom is still in beta....
Have you tried the *228, press 3 then *228 then press 2? I had the roaming indicator flashing with 1X until I completed the steps above...
axcess shop
downloaded wm6.1 and it work great but is there a way to get alltels axcess shop back or no thank you
evdo
i am not romeing but i cant get a go evdo ether just 1x i did *228 and still only get 1x any way to fix this thank you
Check my Reply in this Post! The instructions will get your phone locked back onto EVDO. Not sure what your problem is with the roaming, haven't had any problems with that. I would recheck the SID in EPST again!
http://forum.xda-developers.com/showthread.php?t=366068
**Solved!!!**
Uploaded correct files to megaupload - http://www.megaupload.com/?d=I204KSNF
OUT OF THE BOX FRESH FEELING FOR YOUR XV6800!
Radio: 1.30.60
Rom: 2.09.605.8
Rom Date: 08/03/07
full restore of all original settings!
nuguys solution said:
Be connected to activestink.
(even if your device only boots to the windows splash screen activestink can still connect enough to load this 1.2 bootloader)
Run TitanUnlocker.exe from first folder
FOLOW THE ON SCREEN DIRECTIONS EXACTLY
INCLUDING THE UNPLUGING AND PLUGING BACK IN PART
Be patient and be sure that it is complete.
Then without disconecting, or restarting your device
go to the second directory and folow these directions...
While stil in bootloader mode run ROMUpdateUtility.exe
Follow the onsreen directions.
When your device boots up - LET THE VERIZON CUSTOMIZATIONS RUN.
Enjoy being back on Verizons service.
Now go load whatever roms you feel comfortable running.....
You may need a different bootloader for some roms.
Click to expand...
Click to collapse
I let the customizations run after loading the SPRINT 3.35 Rom updater on my XC6800, I don't think the problem was loading the rom, but letting the damned sprint customizations install instead of a quick reset.
*
I have tried a hell of a lot to resolve this and am convinced that at this point it is going to take a verizon stock rom - the whole thing - to start from scratch and get back from the evil grips of those sprint towers (you sprinters would think the same if in our shoes)...
*
Unfortunately I have not found everything to piece together an entire orig vz rom.
*
The first bad thing that the sprint customizations does is resets the MSL, so now instead of using 000000 as always, you have to find "GetSPC", run it giving it your ESN (under battery) to find out your new "sprintized MSL". This causes you to use sprints towers for everything, add to the fact that it loads a sprint PRL and you are now "stuck on sprint".* when you dial *228 you get a sprint recorded voice that this number is not valid.
Having a xv6700 laying around I was able to set nearly everything in EPST back to where it needed to be (see screen shots)- that got me making calls (roaming) but no i-net, and no *228...
*
Called Data tech support for a aKey, they gave it to me, that didn't work.
*
Dl'ed a vz PRL from http://www.corolada.com/prl/
That got me to be able to connect to vz by dialing *228, but no love, it says "sorry call cust serv...".
*
Went to a corp VZ store and looked at all the settings in EPST changed a couple more, that didn't work.
*
Spoke to the lead geek in charge there and fessed up, he said that it was because of the MSL code change, that *228 sends the 000000 “service sub lock code” to unlock the SPL (EPST) and if the code is different, it will never connect to *228 right (well maybe after they open up their network more, but that is at least months away).* So I said what if I was with sprint and wanted to "convert"? He said they would need sprint to set the MSL to 000000, which would likely be done by sending it in to sprint, then sprint sending it to HTC (I'm sure we can come up w/ something better).
*
After leaving, I received a follow up call from my escalated trouble ticket, and the girl reset my “DMU keys” that finally got me to have i-net (still no *228 love though).
*
So now I am at a OK place, everything works but still roaming, place and receive calls, received network texts from cust serv, and have i-net. However I didn’t want to go through all the set up on my phone just to hard reset anyway so I started off on a quest to find a legit vzw rom.
People keep saying it's posted here, or there or everywhere, I HAVE TRIED everyone I have found and have NOT been able to reset the radio to Verizons peramaters.
Any help out there as to finding the STOCK VERIZON RADIO or best the whole stock verizon rom package?
for those who need help getting the EPST setup I will post the current settings I am using in screenshots.
** I will update this post to reflect the best solution if the thread gets cumbersome.
I used the stock Verizon ROM at:
ftp://up.ppcgeeks.com/Titan/CarrierRoms/Verizon_Stock_ROM/VZW_Passworded_Ruu_signed
I had a similar type issue and I'm working fine now. You'll see a solved post from me with a GPS issue. Hope that helps.
starting to agregate info
starting to agregate info:
Geckotek said:
Here is a repost of my earlier posting on this subject. This will resolve your issues if your Verizon phone has been "Sprintized" or help you restore your phone before returning it to Verizon.
To set your phone back to the default Verizon ROM, do the following:
Download all necessary files 1) Titan Re-locker 2) Stock Verizon ROM 3) ROM Update Utility
Unzip/rar the Stock ROM and the RUU (unrar using WinRAR) ****DO NOT UNZIP THE RELOCKER**** (it is a self extracting zip and will run properly as is)
Place the Ruu_signed.nbh file in the RUU folder
Hard reset your phone by holding down both softkeys, hitting reset, and pressing R (just for good measure)
Connect your phone to your PC and make sure ActiveSync is connected
Re-lock your phone by running Titan_Relocker.exe
Place the stock Verizon ROM in the RUU folder
Run the RUU by running ROMUpdateUtility.exe
For good measure, let the Verizon ROM complete its setup.
I'm doing this from memory so please let me know if I missed a step so that I can update this post.
I hope this is helpful.
Edit: links corrected
Click to expand...
Click to collapse
Geckotek said:
xv6800
Was running 2.3.2 w/ the 3.27 radio. Just updated.
Here were my steps:
Performed hard reset
Connected phone to PC and made sure AS was connected
Ran the Sprint updater
Upon reboot I forced phone into bootloader mode (did this while HTC screen was beginning to appear)
Cooked ROM in DCDs Kitchen...added several options
Ran updater
Notes:
Never had to run *228. Phone and internet confirmed to work correctly. Syncing w/ AS right now, configuring Exchange AS.
Will report back more later, but so far so good.
Click to expand...
Click to collapse
ebb said:
(coming from DCD 1.70 and radio 2.13)
1. Load Olipro 1.20 unlocker (my phone was re-locked after 1.70 ROM)
2. Flash radio
--Reboot was stuck on verizon screen after radio- entered bootloader mode by pressing power+camera, and inserting stylus for reboot. Entered bootloader successfully.
3. Cooked verizon-based rom from DCD 3.0.0 kitchen
4. Flashed ROM
This brought me to the new radio and rom, BUT... when disconected from the desktop, entered the dreaded constant reboot situation, so...
5. Reattached to desktop- this stopped the rebooting. Established activesync.
6. Loaded Olipro 2.40
7. Removed connection from desktop. Removed battery and after reinsert, hard reset device.
8. Ran *228,1 and then *228, 2. Soft reset after each
9. Working great for phone and text. Will play with GPS and report back (yes-- I will enable Location On!)
Thanks DCD for your great work and suggestions along the way here and in the radio thread..
Click to expand...
Click to collapse
Geckotek said:
So to summarize your steps minus the failure follow my directions but if you don't have Olipro 2.4 installed already, do that first. OH, and I didn't need to run *228.
My data speed didn't test so well...gonna see if running a *228 helps.
Edit: HA! As I expected...running *228 jacks me up again. Looking for signal. *22802 kicks it back into signal.....looking into it some more.
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=376873
Geckotek said:
http://forum.xda-developers.com/showthread.php?t=376873
Click to expand...
Click to collapse
your solution is finaly correct - I am uploading the needed files to megaupload so ftp issues don't keep causing problems for people.
I am stuck at the verizon white splash screen and I am trying to get my phone back to stock. I can not establish a connection to my PC via active sync. It there a way to get my phone connected, or is my phone Brick'd now?
Thanks
mcgong said:
I am stuck at the verizon white splash screen and I am trying to get my phone back to stock. I can not establish a connection to my PC via active sync. It there a way to get my phone connected, or is my phone Brick'd now?
Thanks
Click to expand...
Click to collapse
Press camera+power+soft reset
This will take you to the boot screen and you should be able to continue. You should have relocked your bootloader, right?
If so, just go ahead and flash the stock rom.
EDIT: Dont panic. If you are at the Verizon screen your phone is definitely NOT bricked. There are HUNDREDS of cases exactly like your and HUNDREDS more posts telling your exactly how to fix your problem. Search and you shall find.
Even before you actualy get into WinMo even though activestink is not really connected - it is able to connect through and re-flash the bootloader - it took a while to figure that one out for me too...
mcgong said:
I am stuck at the verizon white splash screen and I am trying to get my phone back to stock. I can not establish a connection to my PC via active sync. It there a way to get my phone connected, or is my phone Brick'd now?
Thanks
Click to expand...
Click to collapse
The moral of the story is, don't let Sprint customization run!
I did and had heck for 2 days. After flashing and re-flashing. i finally got back to original vzw rom, but data still didn't work, even after talking with tech support.
I took my phone to a local vzw store and they were able to fix it.
30 minutes later, I had the dcd3.01 rom installed and everything working perfectly.
Next big rom update, I will wait for others to screw up before jumping in.
....
plz up date the wiki with this
I did that same thing a month ago. Ran the damn Sprint Radio/Rom package and was stuck on Sprint towers. Even going back to the stock Verizon rom didn't help. I manually loaded a PRL and finally had phone calls, but no data. After many hours on the phone with Verizon giving me AKEYs, refresing towers, releasing stuck data sessions.... They finally sent me a replacement phone. Nice to see this issue has finally been resolved.
vx6800 bricked
I am new here but I need some help.
I have read and reread all the various posts but cannot get past the splash screen. During startup, at the bottom it, i get R 1.30.60 and D 3.35. It appears my problem is mismatched ROM and Radio version. However, trying to get back to stock rom, my device is not even detected by activesync and no matter what I do, I end up getting error - device not connected.
Thanks
benji
nuguy said:
**Solved!!!**
Uploaded correct files to megaupload - http://www.megaupload.com/?d=I204KSNF
OUT OF THE BOX FRESH FEELING FOR YOUR XV6800!
Radio: 1.30.60
Rom: 2.09.605.8
Rom Date: 08/03/07
full restore of all original settings!
I let the customizations run after loading the SPRINT 3.35 Rom updater on my XC6800, I don't think the problem was loading the rom, but letting the damned sprint customizations install instead of a quick reset.
*
I have tried a hell of a lot to resolve this and am convinced that at this point it is going to take a verizon stock rom - the whole thing - to start from scratch and get back from the evil grips of those sprint towers (you sprinters would think the same if in our shoes)...
*
Unfortunately I have not found everything to piece together an entire orig vz rom.
*
The first bad thing that the sprint customizations does is resets the MSL, so now instead of using 000000 as always, you have to find "GetSPC", run it giving it your ESN (under battery) to find out your new "sprintized MSL". This causes you to use sprints towers for everything, add to the fact that it loads a sprint PRL and you are now "stuck on sprint".* when you dial *228 you get a sprint recorded voice that this number is not valid.
Having a xv6700 laying around I was able to set nearly everything in EPST back to where it needed to be (see screen shots)- that got me making calls (roaming) but no i-net, and no *228...
*
Called Data tech support for a aKey, they gave it to me, that didn't work.
*
Dl'ed a vz PRL from http://www.corolada.com/prl/
That got me to be able to connect to vz by dialing *228, but no love, it says "sorry call cust serv...".
*
Went to a corp VZ store and looked at all the settings in EPST changed a couple more, that didn't work.
*
Spoke to the lead geek in charge there and fessed up, he said that it was because of the MSL code change, that *228 sends the 000000 “service sub lock code” to unlock the SPL (EPST) and if the code is different, it will never connect to *228 right (well maybe after they open up their network more, but that is at least months away).* So I said what if I was with sprint and wanted to "convert"? He said they would need sprint to set the MSL to 000000, which would likely be done by sending it in to sprint, then sprint sending it to HTC (I'm sure we can come up w/ something better).
*
After leaving, I received a follow up call from my escalated trouble ticket, and the girl reset my “DMU keys” that finally got me to have i-net (still no *228 love though).
*
So now I am at a OK place, everything works but still roaming, place and receive calls, received network texts from cust serv, and have i-net. However I didn’t want to go through all the set up on my phone just to hard reset anyway so I started off on a quest to find a legit vzw rom.
People keep saying it's posted here, or there or everywhere, I HAVE TRIED everyone I have found and have NOT been able to reset the radio to Verizons peramaters.
Any help out there as to finding the STOCK VERIZON RADIO or best the whole stock verizon rom package?
for those who need help getting the EPST setup I will post the current settings I am using in screenshots.
** I will update this post to reflect the best solution if the thread gets cumbersome.
Click to expand...
Click to collapse
I got this problem fixed with the help of an uncommonly smart tech support agent.
My first problems started when I accidentally put the sprint rom on my phone and let it boot.
I just called tech support about three times before I saw this post and they couldn't help me and they even did a DMU key reset without my knowledge and that didn't work. The last guy I talked to told me to bring the phone back into the store that I got it to get it replaced. Not wanting to do that beings that this was the last phone the store had in stock, I did one final search on google and found this site. After reading this post, I called back in to ask them to do a DMU key reset. The tech support agent then informed me that they already did a DMU reset and it obviously didn't work. He then wanted to try "something". He asked me to take the battery out of the phone and leave it like that while he put me on hold. I was on hold for about 3 minutes and when he got back on, he asked me to get back onto the phone and asked me to boot the device up again. He then asked me to dial *228 and let the phone reprogram. After I did that and it rebooted, I was able to use data. Whoohooo!!!!
I asked him what he did for my own personal benefit and he informed me that he actually temporarly removed my data package from my plan and reaplied it. But it was important that the device was turned off while he did it. Hence, the removal of the battery. I was very pleased with this guy. I thanked him profusely.
I'm posting this for the benefit of other people who are having problems with their data package after installing the sprint rom.
I haven't posted before, but I have a pretty difficult problem.
I tried installing one of those Sprint ROM/Radio setups on my phone, and like a dummy I let the customizations run. So here's what I did:
1) I flashed back to Verizon stock using the relocker and stock radio/rom. Once completed, it still shows roaming.
2) Then I used *228 option 1, then option 2, and the roaming icon goes away. Oh yeah, I also get the message "we are currently unable to authenticate your phone". No problem, not going to do anything else yet until I get a ROM/Radio combo I want.
3) Then I flashed the unlocker and (insert ROM/Radio combo here). I've tried most of them, following the compatibility list posted on this site. Most version of DCD's, 5067 (or whatever the # is), and radios 3.35, 3.37, 3.39, 3.49, etc. Once I get everything set, get a new A-key, I'm still roaming. The bottom line is that it doesn't matter what I use; the phone goes back into roaming mode. I then tried *228 option 1/option 2. *22899 does not work at all. I've tried to have them do the DMU resets; that doesn't seem to work. I've downloaded and installed new PRL files; that didn't help. In addition to roaming, my data isn't working either. I gave up and reflashed back to stock using the posted procedure.
4) Go back to step 1. I'm somewhere in this endless loop as we speak.
I can't fix it. I've followed almost every recommendation on this site. Verizon is sending me a new phone. In the meantime, I'd like to continue to try to fix this, but I don't know what else to do. Can anyone help???? Thanks.
schoolio said:
I haven't posted before, but I have a pretty difficult problem.
I tried installing one of those Sprint ROM/Radio setups on my phone, and like a dummy I let the customizations run. So here's what I did:
1) I flashed back to Verizon stock using the relocker and stock radio/rom. Once completed, it still shows roaming.
2) Then I used *228 option 1, then option 2, and the roaming icon goes away. Oh yeah, I also get the message "we are currently unable to authenticate your phone". No problem, not going to do anything else yet until I get a ROM/Radio combo I want.
3) Then I flashed the unlocker and (insert ROM/Radio combo here). I've tried most of them, following the compatibility list posted on this site. Most version of DCD's, 5067 (or whatever the # is), and radios 3.35, 3.37, 3.39, 3.49, etc. Once I get everything set, get a new A-key, I'm still roaming. The bottom line is that it doesn't matter what I use; the phone goes back into roaming mode. I then tried *228 option 1/option 2. *22899 does not work at all. I've tried to have them do the DMU resets; that doesn't seem to work. I've downloaded and installed new PRL files; that didn't help. In addition to roaming, my data isn't working either. I gave up and reflashed back to stock using the posted procedure.
4) Go back to step 1. I'm somewhere in this endless loop as we speak.
I can't fix it. I've followed almost every recommendation on this site. Verizon is sending me a new phone. In the meantime, I'd like to continue to try to fix this, but I don't know what else to do. Can anyone help???? Thanks.
Click to expand...
Click to collapse
dang, im here too... any fix?
quadjacks said:
dang, im here too... any fix?
Click to expand...
Click to collapse
Nope. New phone.
schoolio said:
Nope. New phone.
Click to expand...
Click to collapse
Verizon Stock ROM/PRI Update should fix calling
A DMU reset is PROBABLY needed to fix data (need to finango your way around tech support to get one)
scrawnyb said:
Verizon Stock ROM/PRI Update should fix calling
A DMU reset is PROBABLY needed to fix data (need to finango your way around tech support to get one)
Click to expand...
Click to collapse
Nope, did all that too.
schoolio said:
Nope, did all that too.
Click to expand...
Click to collapse
ok i am BACK!!! WOOT|WOOT
here is what i did.
Using the files from post 1 of this thread as no others i tried worked!
1 hard reset
2 ran relocker
3 ran ruu utility
4 allowed cust
5 ran *228
finaly no triangle (raoming icon), but not data
6 called VZW CS, explained i had done a hard reset, BLAH...BLAH...DUH...DUH... not sure why this is happening
a. she had me do everything i had already done (*228), reset username and pass...etc.
b. after 30 mins and at last resort, she removed then readded me to the system (reprovisioned, much like when cable internet modems go offline) SUCCESS
remember only use files from post one of the ablve link, others on here, ppcgeeks, smartphonejunkie oddly didnt help!
Now im back up to Rom 20226 radio 3.42... man im hard headed, but i have a kewl phone again!!!! hope this helps!!!!
NOTE: i was not able to use ##778 to manually program!!!!! so if you have a good tech, this may give him clues to your REAL issue.
also look here post 24
http://forum.ppcgeeks.com/showthread.php?p=271602#post271602
quad,
i am waiting (24 to 48 hrs )for their network team to do.... something to my phone, possibly the DMU reset. My tech wasn't able to do that on her own. I'm wondering if i can get a regular tech to do what they did for you....when you say they removed you then added you to the system, not exactly sure what that means
I'm Jealous.....
EDIT: BTW, my data connection settings won't keep a username and pwd stored....keeps dropping them every time after i put em in
I'm sure the answer to my question is somewhere in this forum...but no matter how I search...it does not reveal anything I can use.
I recently upgraded to DCD 3.2.6 with the .50 radio and SPL 2.47 and used the Verizon carrier cab
My data connection fails every time I try to connect. I get the message PPP Connection Error.
After reading a few post within the forum...it was sometimes suggested to re-run the carrier cab which I did about four times...it tell me that it successful but still fails to connect.
I then called Verizon and they where unable to resolve my connection issue...so they are sending me out a new phone...oh I'm using the XV6800 Verizon.
So...what should I do now?
See if somebody can help me to get my data connection working and tell Verizon not to send out a new phone...or reset my XV6800 back to stock ROM and go for the new one...which of course will probably have the new stock ROM on it...which will not allow me to install a custom ROM.
Any suggestions?
dlitz said:
I'm sure the answer to my question is somewhere in this forum...but no matter how I search...it does not reveal anything I can use.
I recently upgraded to DCD 3.2.6 with the .50 radio and SPL 2.47 and used the Verizon carrier cab
My data connection fails every time I try to connect. I get the message PPP Connection Error.
After reading a few post within the forum...it was sometimes suggested to re-run the carrier cab which I did about four times...it tell me that it successful but still fails to connect.
I then called Verizon and they where unable to resolve my connection issue...so they are sending me out a new phone...oh I'm using the XV6800 Verizon.
So...what should I do now?
See if somebody can help me to get my data connection working and tell Verizon not to send out a new phone...or reset my XV6800 back to stock ROM and go for the new one...which of course will probably have the new stock ROM on it...which will not allow me to install a custom ROM.
Any suggestions?
Click to expand...
Click to collapse
what do you have for your Data Network Connect? #777 and then you need name, password, and domain. I don't remember what those are off the top of my head but need to right or you will not connect. You do have a data package from Verizon, sorry I am in support and have to ask all the simple questions as well as the hard ones. Also have you tried to reload the radio ROM and the DCD ROM again, with the Verizon CAB of course? Most of the issues are cleaned up with reloading the ROM not the carrier cab. Also make sure that your data connection icon in the Comm Manager is lite up or on.
Verizon Data Tech Support ran me through some setting which one of them was to make sure I had my phone#@vzw3g.com and the pass of vzw set correctly...which I did
That still did not work...when that did not fix the problem...he went no further...and said we need to send you out a new phone.
I'm in the process of downloading the ROM radio again and going to try the procedure again...
dlitz said:
Verizon Data Tech Support ran me through some setting which one of them was to make sure I had my phone#@vzw3g.com and the pass of vzw set correctly...which I did
That still did not work...when that did not fix the problem...he went no further...and said we need to send you out a new phone.
I'm in the process of downloading the ROM radio again and going to try the procedure again...
Click to expand...
Click to collapse
Your probably not authenticated on the VZW network. Its miserable when that happens. DO you have a spare phone around? If so activate that phone against your phone number. Wait five minutes and activate the 6800 again. I do it all the time. It will resolve this issue. There is something called a "group password" you are missing. Only VZW can put that in by re provisioning the phone.
There tech support never catches this. IF you have to, call them and just tell them you need your AKey reset. You will get transfered to a security department. They will walk you through a bunch of crap then finally reset your AKEY. You should be able to authenticate as you as you dial the number that lets you program the phone. Cant remember what it is off the top of my head. ##xxx
dlitz said:
I'm sure the answer to my question is somewhere in this forum...but no matter how I search...it does not reveal anything I can use.
I recently upgraded to DCD 3.2.6 with the .50 radio and SPL 2.47 and used the Verizon carrier cab
My data connection fails every time I try to connect. I get the message PPP Connection Error.
After reading a few post within the forum...it was sometimes suggested to re-run the carrier cab which I did about four times...it tell me that it successful but still fails to connect.
I then called Verizon and they where unable to resolve my connection issue...so they are sending me out a new phone...oh I'm using the XV6800 Verizon.
So...what should I do now?
See if somebody can help me to get my data connection working and tell Verizon not to send out a new phone...or reset my XV6800 back to stock ROM and go for the new one...which of course will probably have the new stock ROM on it...which will not allow me to install a custom ROM.
Any suggestions?
Click to expand...
Click to collapse
You can revert to a stock pre-gps ROM. There are instructions to do it somewhere. From then you skip the VZW update and just follow the normal path. I have done it with my phone a 100 times. Thats how I know about the authentication issue you are having.
I do have another phone around here...I might try that
I have just finished re-installing the radio ROM and the 3.2.6 ROM...installed the Verizon carrier cab
ran the *228 option 1
waiting for the phone to reset.
I'm just wondering if I'm following the correct procedure upgrade the phone...
I used the Wiki...but it appears to be as organized as my home office...
so I'm not sure where the best tutorial is to follow upgrading the phone.
Edit...that's was a no go...same issue
Not sure what you mean in your last post...care to elaborate a little on that?
I also read somewhere that if I activate another phone...and then re-activate the 6800...its possible that I will loose my data plan associated with the 6800...
I guess I would have to call them or log into the account and re-add it...
Just an update...
I Spent about 45 minutes on the phone last night with Verizon Tech Support.
I called them back after ready your post above. I asked them if they would reset my Akey, but they wanted me to go thru a few other troubleshooting steps first.
finally at the end of the conversation...the girl on the phone said that the Verizon system is getting an A-Key from the phone and since its getting one...it can not be reset...
So...I'm getting a new phone anyway...
I guess its not all that bad...I have been seeing issues with it locking up on me when I was on the stock ROM...
Thanks for the suggestions...time to go find the thread that will put it back into stock status...for shipping back to Verizon.
http://forum.xda-developers.com/showthread.php?t=423597&highlight=ppp+connection+error
ibenjakinov said:
http://forum.xda-developers.com/showthread.php?t=423597&highlight=ppp+connection+error
Click to expand...
Click to collapse
Thanks
I've been through that thread already
However, I'm just going to wait until the new one arrives and try again...
make sure your settings for your data connection do NOT have anything under domain. also, under Connections --> Advanced--> Select Networks, make sure that Verizon Wireless is selected for the first option. i havent heard anything about this for a while, but if this is happening when you try to send or receive an MMS, it can't hurt to make sure your X-VzW-MDN key is set to your 10 digit phone number (HKLM\Software\Archsoft\Archsoft MMS UA\Config\mm1\wspheader)
kflipproductions said:
make sure your settings for your data connection do NOT have anything under domain. also, under Connections --> Advanced--> Select Networks, make sure that Verizon Wireless is selected for the first option. i havent heard anything about this for a while, but if this is happening when you try to send or receive an MMS, it can't hurt to make sure your X-VzW-MDN key is set to your 10 digit phone number (HKLM\Software\Archsoft\Archsoft MMS UA\Config\mm1\wspheader)
Click to expand...
Click to collapse
The first part of your message was checked by me and Verizon...just to make sure...
When I had everything installed and running after the upgrade...MMS was not even available...only thing I had was SMS and email.
I had to install that GC mms/sms cab file to get MMS back on the phone...and that did not even help.
As for the last part of your post
I know that's a registry key...but how do you get to it to check.
Also...just for sh**s and giggle knowing I'm going to be sending this phone back to VZW when the new one shows up...
After converting it back to stock radio, ROM and SPL
I used the official VZW MR1 ROM update and flashed the phone with that...same issue, unable to make data connections...
Thanks for all the support and suggestions...
dlitz said:
Thanks
I've been through that thread already
However, I'm just going to wait until the new one arrives and try again...
Click to expand...
Click to collapse
I had the same problem and when I switched to my old Razr and then back to the XV6800 then ran the carrier cab it worked. It may have took 2 tries (switching back and forth between phones). I did have to reselect a data plan when activating the 6800. I also may have run the carrier cab a few times. It took a lot of messing around but I finally got it to work. I guess if your getting a new phone none of this really matters though.
Alright, i just received a warranty replacement phone and was in the process of setting it up. It had the latest MR2 ROM installed on it. Went ahead and loaded SPL 2.40 and DCD 3.2.6 ROM, left the shipping 3.37 Radio.
The problem started when I did the aGPS walkthrough. As soon as I wrote the settings to the phone and reset, the phone stopped making or receiving calls. It just gets stuck on Dialing.... then either says Call Lost or Call Ended. I tried reloading the backup I made of QPST settings and still no luck.
Did manual provisioning, still no luck. Spent 45 minutes on the phone with Verizon trying to diagnose after I flashed back to MR2. They're sending me another replacement. I just don't want this to happen on the new one.
thats normal .. (well some what) .. all you need to do is *228 or call support
to do an over the air Auth .. basically your A key or Auth info. is miss match ..
*228 sometimes fix this .. if not just call support .. . tell them you did a hard
reset to clean up space on the phone and it no longer make calls .. they will
re-send the A key and other Auth info to your phone!! not a big deal your phone is ok
Thanks for your quick reply. The phone won't even complete a *228 call. Every time I try dial *228 it gets stuck at Dialing.... until it says something like call lost.
Verizon reps tried a couple things and ended up replacing the phone instead. How do I avoid this next time? Is it really necessary to downgrade to the 2.09 ROM first? Thanks.
What are you trying to do with the phone by adding a custom rom? If you don't downgrade before going custom then standalone gps won't work. I imagine you accidentally changed a setting in qpst that you weren't supposed to. Or maybe you have discovered a new problem with going custom from MR2 without downgrading first. Not many people have messed with MR2 since Verizon messes everything up. I would just recommend downgrading before going custom to make sure the Verizon troubles and removed from the phone.
Thanks for the help. I think this is an added problem from not downgrading. I have done the aGPS fix on 3 other titans the exact same way and never had a problem. But now, even the QPST backups don't work.
Ok. This is as CONFIRMED as I can make it since I received another replacement Titan and was successful this time around.
If you don't downgrade to the old ROM and bootloader and then upgrade and do the QPST aGPS, you will loose your ability to make or receive phone calls beyond repair. You WILL have to swap out your device.
If you downgrade first, everything works normally.
Hi,
I got a problem and is that for some reason after installing Voip programs I see that my username on my device information is different that the one it should be. This is making the phone not connect to sprint.
Is theres a way to fix this?
I have tried changing to different roms and right now i have installed the stock sprint rom to see if would of went back to normal, but the wrong username is still there.
Will apreciate the help
Ok sprint fix it for me by phone.