hi to all xda family, i need ur help please.
i am using imate jasjam hermes 100, i am having an annoying problem with my set. The front buttons of my jasjam stop working suddenly, but the light behind the bottom two call buttons still remains on even i go to stand by time using side power key. Sometimes the screen fades away and a blank white screen appears. It seems to me that the the cell hangs temporarily as after sometime it starts working fine (in some cases i have to soft reset the device). but in the scenario described above my cell is in on state as if someone calls me, i can hear the caller tone. i just wanna ask to all of you that if it is a software problem or a hardware problem and how to solve that.
i am using joshkoss manila2d plane jane version with radio rom 1.16.0.0 and hardspl 2.10 installed. i've also tried tai 6.5 roms, but the problem still exists.
Related
I've installed the newest version of Pocket Bluetooth Tools on O2 XDAII with latest O2 ROM release. Two problems:
- the XDA II does not go into standby mode after answering a call
- bluetooth remains active instead of switching off after x minutes (the clock on the screen is white).
What am I doing wrong ?
Thanks,
Can I just bump up this question again. I'm very happy with Pocket Bluetooth Tools, accept for the powerdrain caused by bluetooth being on. PBT is supposed to switch is off automatically after a minute, but I find, even when it goes all the way around and goes completely white, bluetooth does not switch off.
Has anyone else found a solution to this problem? Im using the latest rom from O2 (1.66 I think).
Regards
Surur
I am running 1.66WWE latest version of rom on my XDA ii and the latest bluetooth tools and it shuts down bluetooth perfectly, it counts roudn getting greyer and at the end it goes fully white and the blue light stops flashing to indicate that bluetooth is turned off, however the XDAII's bluetooth section still reports it as on and the headset symbol stays enabled, but if i press the button on my headset i cannot get into the phone screen so it is definatly working on mine,
It must be another piece of software stopping it powersaving on your one, or something wrong in the registry maybe?
Hi everyone, new to the forum!
I have a couple of problems with my wallaby o2 xda, and I was wondering if any of you could help. Occasionally, everything becomes very slow, and the backlight comes on and off intermittantly (the two problems always come together); to rectify this I have to perform a full reset. Also, on occasions clicking on contacts (weather it be with the stylus or using the button on the top left) does not work, and I have to do (what I think is called) a half reset.
I hope you can help
Is there a registry tweak to allow the speakerphone to stay enabled when you close the flip? Currently it ends the call.
I believe the same thing happened with the old MPx220 and the MPx200 but nothing was ever figured out for these phones.
I would like to know this as well.
Bump - Speakerphone while lid closed...
Any news on this?
My Googling is telling me thus far - NO! NO! and NO!
Any Russian Gurus care to negate this?
speakerphone
Ok, I am trying to figure this out, here is what I have so far,
I have two 3125's, one was running an old dopod rom and the other the most recent Cingular release. (will get numbers later)
On the old phone, if I hit the "lock keys setting" (press and hold home button), while on a call with the speaker phone on, I can close the phone, the call continues and the outer display shows the call info (ie, who the call is to and connection time)
One the newer phone, with the same setting, the phone just hangs up when you close it.
I backed up the old phone with sprite backup, then ran sprite on the newer phone thinking maybe the registry setting would carry over (in case I was missing something), but the newer phone still just hung up when closed during a call.
After several rom changes I remembered why I quit using the old phone, the charging port came loose and does not work, so my guess would be that the old phone stays on due to the broken charging port, what leads me to this is of course if you have the headset in, the phone can be closed while on a call.
Where does that leave us? It would seem that the issue is not a registry value change (although I won't give up on trying to find one) but a software issue and until someone figures out how to change it were are stuck with no closed speaker phone.
Here's some of the problems that I am having....
1. When using phone, I occasionally cant hang up - whether I use the screen button or the pushbutton - the only thing that lets me end the call is a soft reset. Imagine!!!
2. Yesterday, for no reason, the ringtone for an incoming call played 2x faster than it should have (ie. the speed of the song was doubled)
3. Just after I notice the ringtone song issue, I tried to use voice dial, and the prompts for voice dial were also playing twice as fast, a soft reset seemed to have fixed the problem... lets see if it happens again.
4. After installing WM6 Crossbow Underground, I was having problems not getting ANY calls, so I upgraded the Radio Rom to 2.61.11 and it seemed to work, BUT then I started noticing that I was getting SOME CALLS AND NOT AL CALLS, so I switched back to 2.25.11 Radio Rom
5. Under Regional Settings > Time ...I tried to switch to 24HR mode and using it for a while, I went back in to revert back to the 12HR mode but it wouldn't let me switch back to 12 hour mode.
6. When I touch the screen to Turn ON Flight Mode (shut off the radio), and then touch the screen to Turn OFF the Flight Mode, the dialogue STILL says Turn ON Flight Mode, even though its already ON (it should change to say, Turn OFF Flight Mode).
7. I was just on the phone with someone when a text msg arrived, and it booted me off the call I was on (it hung up).
8. When on a call, I touched the Mute botton on the screen to MUTE the call, but when I tried to UNmute the call it wouldn't let me.
9. Did anyone notice that the SIMPLE LOCK (4 digits) now requires you to click on the unlock button after entering the code? WM5 didn't require this, if you entered the right 4 digits, you were in, without having to press anything else.
10. When I am on a call, and another call comes in (call waiting), I cannot answer or ignore the other call... it doesn't respond to me whether using the touchscreen or the buttons.
And there's MORE that I will post another time.
Any suggestions or solutions, to these problems?
Actually I would recomend you upgrade to Most Beautiful version
I used Underground version, and Office Mobile doesn't work too
Everything is ok here with MB (search with this and you'll find it in piratebay under applications) version
Where is the "Most beautiful edtion"?
ANTC said:
Where is the "Most beautiful edtion"?
Click to expand...
Click to collapse
Uhhhhh, I think he said "you'll find it in piratebay under applications" didn't he?
find it here
here you go link for the rom you want andmany others
http://rapidshare.com/users/EXGZ7T
do you still need to apply the battey leak patch and the other extra stuff you had to do with underground
Hallo!
I have a mysterious Problem:
When i make a call than is the Display on and active - I can activate the speaker an so on.
IF i get a call the Display is aktive so long as i take the call. Then the Display gets dark and inaktive. So it´s inpossible to activate speaker or others. Pressing ANY! Key is not succesfull, intead the right - but THEN, the Call is over...
I tried the system, two other SimCards, Regitry-Hacks, flashing other Rom´s!
Nothing solve this Problem....
Mysterious: After flashing a new SystemRom, one or two times ist works, but than it´s like before.
ALL other functions are OK, so a hardware-Problem is unrealistic.
The HTC-support has also no idea (change the SimCard....).
It is NO other Software installed and i tried the original ROM´s from T-Mobile (win6.5) and some other Rom´s (like Duttys).
WHAT can I do?
make sure there's nothing blocking the proximity sensor during the call.