Related
Can we use XDATools to backup and restore XDA II ROM? Or XDA II provide a way to do the ROM backup and restore?
vbexpert said:
Can we use XDATools to backup and restore XDA II ROM? Or XDA II provide a way to do the ROM backup and restore?
Click to expand...
Click to collapse
is there a way to enter Bootloader method for XDA II?
You can enter bootloader on xda ii via power+any direction button+reset. Word of warning, it will hard reset as well.
palmop said:
You can enter bootloader on xda ii via power+any direction button+reset. Word of warning, it will hard reset as well.
Click to expand...
Click to collapse
Does it have the option to backup and restore ROM? Thanks!
it has d2s command to dump rom to sd, but don't know the reverse...
s2d like on an ipaq ?
is that a raw command on terminal software?
maybe its the same on ipaq?
lets find out
didnt get the terminal software to work though
dunno witch
found this
Here's how:
1. First insert the formatted SD card to the healthy iPAQ. Connect the cradle/cable to your computer's serial port. Install the A/C adaptor to your cradle.
2. Prepare the healthy 39xx to enter DEBUG mode:
- press and hold button: power, contacts, and inbox, and do pin reset.
- if your iPAQ shown all-red COMPAQ display, with 'SERIAL' text above, then you're in the debug mode.
- sit the debugged iPAQ to the cradle.
2. Open hyper-terminal, make a new connection, using these setting:
- the COM port where the iPAQ is connected.
- 115,200 bps
- 8 databits
- no parity
- 1 stop bit
- NONE handshaking.
- Connect!
3. Once connected, hit once to show the prompt SER>
4. On prompt SER> type "?" for displaying all the commands avail.
5. On this process of ressurection, we'll gonna use only two command: "d2s" (device to storage) and "s2d" (storage to device).
6. type "d2s" and hit .
7. The ROM copying process will begun, and you'll see a 'progress bar'. This may take apprx. 10 minutes.
8. When it's finished, you'll see the confirmation on both of your hyper-terminal screen and your iPAQ.
9. Disconnect the hyper terminal session.
Now the resurrection steps:
1. Prepare your dead 39xx to debug mode.
2. insert the SD card (which is now already filled with the 39xx ROM)
3. start a session on your hyperterminal again (using the same setting as above).
4. once connected, hit once to shown the SER> prompt.
5. type "s2d"
6. Your iPAQ will display a warning that current ROM will be erased, press 'power' button to confirm.
7. Starting the process of erasing the ROM of your dead iPAQ. This will take apprx. 7-9minutes.
8. Once the erasing process is done, it will automatically re-write the ROM of your dead iPAQ with the NEW ROM from the healthy iPAQ. This process took much longer, apprx 15 minutes.
9. When the copying process' done, both of your iPAQ and hyperterminal will shown an OK confirmation.
10. Disconnect the hyperterminal session.
11. Unplug your iPAQ from its cradle, do a soft reset.
12. Your dead iPAQ's risen!
gonne TRY !!!!
ITS WORKING
downloading rom now from my phone for backup
ftp://ftp.hilgraeve.com/htpe/htpe63.exe
for direct terminal software download
** rom is now on my card.
but how to replace the rom with an english one.
you cant read the card anymore
There has to be a way to dump that SD to a file. For me I can go to my friend's house and dump his English ROM and put it on my MDA II, but for many others, they'll need a file. Let's focus on how to do this.
I got MDA II from germany couple of days ago, and have been stuck with the German language. I've been searching and seaching for English ROM for couple of days and still no luck.
Can someone PLEASE please please make an image of the English ROM of their XDA 2 and post it here.
Thanks in advance
I will post it, as soon as I can get my hands on it
we just need to find another xda2 with english rom
and then dump that one
and use the rom for you own
I need the German XDA II ROM (because I have a MDA II, but I have an O2 card).
Can anyone dump a German XDA II ROM please!?!
how do i make a backup/image of the ROM? please give me step by step instructions. Thanks.
Backup & Restore of ROM MDAII
Hi all,
to backup your ROM:
1) put your device in bootloader mode
2) connect via cradle
3) use any terminal (minicom) to connect to the used port (/dev/ttyUSB0)
- you should see something like 'USB>' or 'SER>'
4) put an SD Card into device
5) type d2s on command prompt
to restore your ROM:
1) put your SD-Card into device
2) put your device in bootloader mode
3) the device will ask you to press power to flash the rom
and how do we change the rom on that SD?
We cant read the files
its formated in a non standard way
How to backup the Radio Stack of MDAII??
are there any possibilities to backup and restore the radio stack using the bootloader method?
thanks a lot,
bio
akira Posted: Sun Nov 16, 2003 18:48 Post subject:
--------------------------------------------------------------------------------
and how do we change the rom on that SD?
We cant read the files
its formated in a non standard way
Click to expand...
Click to collapse
Did you tried with WinHex software?
It is not formatted in FAT/FAT32/NTFS, etc. Thus WinHex can't read it...
References:
http://forum.xda-developers.com/showthread.php?p=1840788
http://forum.xda-developers.com/showthread.php?p=1684559&highlight=EBOOT.NB0#post1684559
chartreux said:
No, don't use the EBOOT from the ATOM EXEC(MN2). you must use MN1(from ATOM STD). I had attached it to you.
here is the step.
1. copy eboot.nb0 to your SD-CARD (in the root) and insert your card to your ATOM EXEC
2. preset camera+reset
3. you will see the progress status (wait until your device off)
4. TAKE out your SD-card
5. preset camera+reset again (you will see MN1 bootloader)
6. hook up your USB
7. run software update utility (you may use WM5 or WM6 EXEC ROM)
8. wait until 6% stack on extended ROM (you will see failed status on your bootloader screen during update ext ROM)
9. press on/off + reset perform hard reset
10. your windows will be up and able to sync with activesync. (your bootloader now MN2 again!!)
11. now you may perform the DSUU and this time your EXT rom will be update successfully.
12. delete EBOOT.bin from your SD card
13. done and enjoy.
please beware, you are playing the most dangerous part now.
Click to expand...
Click to collapse
Follow by the instruction.
I use the 2GB Mini SD card to flash the MN2 bootloader to MN1.
Before I copy the EBOOT.nb0, I format the MiniSD and I had confirmed the card can be read in AtomExec.
The screen display "transfer completed" after I inserted the MiniSD and press camera+reset.
After the message was shown, no response come out in next 3 - 5 minutes.
So I press camera+reset again.
The Atom Exec will load in MN2 bootloader again.
I got a trouble in step3.
I had tried the Atom EBOOT.nb0 & Atom Exec Offical WM5 EBOOT.nb0.
Both of them are same, after the message come out and nothing to do.
Any solution I can go back to WM5 ?
I'm can not stad for the AtomExec unable to use the Bluetooth headset while in phone call.
Try to use 256MB memorycard.
Is there can not use in 2 GB ??
it is because I have not 256 MB MINI SD......
admin88hk said:
Is there can not use in 2 GB ??
it is because I have not 256 MB MINI SD......
Click to expand...
Click to collapse
It's been proofed in WIKI and it's work. Try it.
Maybe the problem is you have to borrow 256MB or 512 MB
admin88hk said:
Is there can not use in 2 GB ??
it is because I have not 256 MB MINI SD......
Click to expand...
Click to collapse
For some brand, 2gb mini sd can't used for sdflashing. I have 2gb V-Gen and i can flashing with it.
do you know that can I use Kingston to do the flashing ??
to hiro77, thx for your reply, I am lookig for my friends which have 256MB Mini SD
SDflashing tested by me:
- 256MB: V-Gen/MCPro=OKE
- 512MB: V-Gen=OKE
- 1GB: V-Gen/MCPro=FORGET IT
- 2GB: V-Gen=OKE
Thank you very much for chartreux, hiro77, abusalza, katon808, tjlabais and homer.
I am using a 64 MB MiniSD Card succuessfully roll back to WM5 today.
All step are smoothly.
admin88hk said:
Thank you very much for chartreux, hiro77, abusalza, katon808, tjlabais and homer.
I am using a 64 MB MiniSD Card succuessfully roll back to WM5 today.
All step are smoothly.
Click to expand...
Click to collapse
Hi,
can you help me where I can download the Atom Exec WM5 EBOOT.nb0 file.
thanks
Same me
when i cannot find eBoot.nb0 form Office ROM.
I use eBoot.nb0 from Atom/Atom Pure WM 6.0 Kumara Touch New
Extract to folder.
-I copy it to 1 Gb Kingston MiniSD.
-Hard Reset I found my Atom Exec get MN1 Loader file.
-My Atom Exec Show Load eBoot and Ignore other. Cuase MiniSD Have 1 file only.
-when finish and show soft reset.
I remove my MiniSD and Camera+Softreset to MN1 boot loader mode.
-Connect to USB. Pc have sound 1 time.
-I use WM5 Office ROM upgrade it.
You will found error 6% in stage 3 Extended Rom.
Don't warry it's bug normally of WM5 Office ROM.
You must Hard Reset and Default Factory by CallKey+EndCallKey.
No Aligment, No Setting Time, when PC found new hardware.
You will try upgrade by WM5 Office ROM again for get Extended ROM and
other.
OK, Hard Reset for finish or Upgrade to WM 6.1 as Me.
today, I finding solution for upgrade my Atom Exec all time.
Cause I Noob for It. And my old PocketPC is Atom Black.
It's has upgrade flow differrence my old PocketPC.
But, This time i understand Atom Exec upgrade and Error 6% Now.
Hope, Your found the way for clear your problem.
The Power still with you.
mikomarco said:
Hi,
can you help me where I can download the Atom Exec WM5 EBOOT.nb0 file.
thanks
Click to expand...
Click to collapse
If you can read chinese you can find EBOOT.nb0 at here
otherwise you can find at here
Hi. Im trying to upgrade my MWG Atom Life from WM 6 to WM 6.1.
Mainly cause I heard that WM 6.1 is better performance & Battery.
After looking around all the confusing roms I think i shall settle with this one
http://forum.xda-developers.com/showthread.php?t=460145
Other sugestions would be apprichaited but I know if i ask ill probably be told there are many roms out there...
However can someone tell me if there is an installation procedure for dummies. I dont even know how to format my SD Card I dont even know where to start this upgrading procedure.
Im sure u wernt all born upgrading and flashing ur atoms... or where u
dear fuligin,
well, it's all in the wiki. I think you should read it carefully.
but this is my suggestion on how to upgrade your device (that's been written in this thread http://forum.xda-developers.com/showthread.php?t=460145) :
Up ROM Guides: (up from MMC)
- Battery over 70%, MiniSD is smaller than 2G, format FAT16 (on PC is FAT).
- Download and extract with the password below, copy file AL1.DIO to MMC.
- Press Record + Reset, leave Reset first => ***MiniSD Detected*** => waiting 100%, Atom Life auto reset and you have new ROM!
Thanks
Thanks armand_x3m
So it seems to be as simple as the instructions. I shall attempt it and see if I have a working phone after that For some reason Im thinking that this upgrading procdure is more complicated then the simple instructions.
I was trying to flash the RRE_Fuze_Rom_v40_Hybrid rom - only to find out after booting that it contained Windows Mobile Beta - and had expired.. the screen seems to be locked and I cant establish an Active Sync connection to reflash.
I think I saw something before to the degree of putting an image onto an sd card and booting with that in..
Can someone give me some advice on how to re-flash so that I can use my phone.. A link with instructions would be sufficient.
Anyway work arounds are welcome - I don't think I have a mini-sd card reader with me at my office so.. i'm open to "creativity".
P.S. - sorry if this is in the wrong place.
As it says here: http://forum.xda-developers.com/showthread.php?t=448008
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 using a PC (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Raphael Rom Develpoment Page and unzip/unrar it to your computer
3. Goto the Roms Folder and rename the .nbh file to RAPHIMG.nbh
4. Copy the RAPHIMG.nbh file to the root of your microSD Card
5. Remove Sim Card and Restart phone
6. Plug the microSD Card into the phone
7. Press and hold the volume down button, then press the reset button with the stylus. Release the volume down button when bootloader tricolour screen appears
8. Follow the onscreen instructions to start flashing
9. Once phone finishes flashing and says Update Complete, reset with the stylus
10. When it gets to the screen where it configures the stylus, HARD RESET
(hold the VOLUME DOWN and ENTER (center) Buttons, press the RESET button with the stylus tip, then release the RESET button but continue to hold the VOLUME DOWN and ENTER buttons until the reset screen appears)
11. Follow onscreen instructions to set up your New Rom
Click to expand...
Click to collapse
Hope that helps ^^
Thank you so much.. I think i'm back in action now!
Zeraven said:
As it says here: http://forum.xda-developers.com/showthread.php?t=448008
Hope that helps ^^
Click to expand...
Click to collapse
Hello my name is Robin,
Yesterday I tried to install Chainfire 3D but with no luck, I saw after that time it was not made so for Jellybean. very stupid of me now, so do not start my phone when I put it in force update I get a pink screen I can still come from my phone in the normal recovery, but that's the only thing I can. tried wipe cache and reset without result. Can you help me because I already busy two days and it still can not.
Sorry for my bad english I'm dutch.
Greetings Robin
Van anybody help me
please can enyaone give a answer fast? I wan't to give this phone as a christmas present to my cousin
Hope somebody will help me
Robje007 you only get the pink screen if their is no update found below is how to use force update
Upgrade instructions
1. Unzip the downloaded file
2. Place the Update.app inside a folder named "dload" on your SD card root directory
3. Power off and turn on your Ascend Y300 holding volume down + volume up + power button
This was taken from Huawei upgrade guide
Force upgrade
Step 1. A MICRO SD card of 2G or more should be available. The MICRO SD card
made by Sandisk, Kingstone, or Kingmax is recommended.
Step 2. Format the MICRO SD card (This operation is optional).
Step 3. Copy the Software: main package to a directory named dload.
Step 4. Copy the entire dload folder (with UPDATE.APP in it) to the root directory of
the MICRO SD card.
Step 5. Make sure your handset is power off. Insert the MICRO SD card into the
handset. Press the VOLUME UP and VOLUME DOWN key, and then press the
POWER key to power on the phone and enter the Software Upgrade Mode.
Step 6. When the progress bar stop, the phone will restart, if not , you need to
remove the battery manually.
Step 7. Copy the Software:vendor package to a directory named dload. Then
Execute Step 4 – Step6 repeatedly.
If want to install a custom or repack Rom for the phone Then
Press vol up + power to boot into recovery and install the Rom from their. (Keep pressing the buttons until the phone boots into recovery)
If you want to boot into sideloader and use adb to push a Rom then
Press vol down + power if the Hauwei logo stays on the screen then you are in sideloader mode keep pressing the keys for at least 10 to 15 seconds.
Hope this is of help to you
i want to know what alternative volume button flex strips can i use for my huawei y300-0100 as mines damage and its not available in my country