Does the innards from the T-Mobile version of the TD2 fit in the original Diamond2 housing.
Its something I'm thinking of doing...and would like to know if its been done or possible at all.
That would be an interesting project, hope you try it out. They only thing that I could think of not fitting is the speaker, which on the MDA is on the side of the device.
EDIT: Scratch that, the MDA also is on the side. It looks like it could work, but the only porblem looks to be the bottom of the phone, which is much curvier
You will need to purchase a touch screen digitizer if you try this. It is attached to the housing and impossible to remove without damage. Also, when removing the digitizer and other ribbon cables, remember to slide the little black peice slightly to remove it. Very tricky, but I have completely taken the topaz apart numerous times. P.M. me if you run into any snags..... although I don't recommend trying the switch unless you have experience in electronics. Good Luck!
tomtommy306 said:
You will need to purchase a touch screen digitizer if you try this. It is attached to the housing and impossible to remove without damage. Also, when removing the digitizer and other ribbon cables, remember to slide the little black peice slightly to remove it. Very tricky, but I have completely taken the topaz apart numerous times. P.M. me if you run into any snags..... although I don't recommend trying the switch unless you have experience in electronics. Good Luck!
Click to expand...
Click to collapse
I don't have experience! But its never held me back before. At the moment I'm having problems locating a full housing including the front and side buttons..the only housing I can find are without buttons....I was thinking of buying a dummy for the buttons...don't know if thats viable.
Be sure to tell us how it went, and any special steps/problems you encounter.
Although, it really does look more like a cheap LG phone than a Nokia, except for maybe the 5800.
pistonripper said:
I don't have experience! But its never held me back before. At the moment I'm having problems locating a full housing including the front and side buttons..the only housing I can find are without buttons....I was thinking of buying a dummy for the buttons...don't know if thats viable.
Click to expand...
Click to collapse
Ebay! Or try CNN.CN for a more expensive approach.
They even sell a full black housing with the matt black if you want to be different.
http://cnn.cn/shop/t5353-touch-diamond2-topaz-c-277_829.html
CNN.Cn doesn't have the buttons included either
i too want to try it, but encountered the problem of the buttons... No housing is sold with the buttons. For the rest i can't see any difficulties, the Inside of the Compact V and the Topaz should be the same, i mean, will HTC manifacture a complete new phone just for T-mobile? I think just the housing is different.
When i find a way, i'll contact you!
I found one supplier....they include the front buttons but do not include the volume or power buttons
http://www.truesupplier.com/original-full-housing-cover-for-htc-touch-diamond-2-pr-18539.html
EDIT: Sorry it does include all the buttons as well as the front keys.....so ordered everything ...just waiting now
Topaz Antenna
does anyone know where I can I get the topaz antenna from ?
Received my casing today....but need the antenna.....the Compact V antenna is integrated into lower back of the casing as one piece....so its of no use
Dang, that sucks, I have searched for the antenna before, but haven't found any. Maybe try a broken TD2 on ebay or something. Other than that I have no idea
cmstackar said:
Dang, that sucks, I have searched for the antenna before, but haven't found any. Maybe try a broken TD2 on ebay or something. Other than that I have no idea
Click to expand...
Click to collapse
Well thats the only missing piece in the jigsaw.....so if/when I get it I will update the thread....in the mean time, if anyone knows where I can get this or make one up....its looks all plastic with 2 connectors...the connectors I have.
Related
where can i get a black herme housing ?. I want to replace the boring gray housing that the 8525 came with.
Looking for the same thing!
Anyone with some suggestions?
i ordered this one...i'll let you know how it goes.
http://cnn.cn/shop/htc-8525-c-277_322.html
wratran said:
i ordered this one...i'll let you know how it goes.
http://cnn.cn/shop/htc-8525-c-277_322.html
Click to expand...
Click to collapse
Dont mean to bother, but just wondering if there has been any success? Im really interested in this mod.
wratran said:
i ordered this one...i'll let you know how it goes.
http://cnn.cn/shop/htc-8525-c-277_322.html
Click to expand...
Click to collapse
Have you tried it yet?
I just ordered a new Hermes Replacement housing from cnn.cn, however I haven't received it yet.
If you are ordering one just make sure you order the right one for your phone.
For instance, the TyTN replacement body will not work on a 8525 and vise versa...
invictive said:
For instance, the TyTN replacement body will not work on a 8525 and vise versa...
Click to expand...
Click to collapse
I was looking over the cnn.cn and from first looks, it seems like the 8525 OEM black housing will work with the TyTN phone.
Is it confirmed the two will not work with one another? They are the same identical phone but with out the front camera on the 8525. If anyone will or has tried let us know.
I haven't tried, but I doubt it would. If you compare the positions on the different buttons - you can see that it the buttons doesn't correspond on the two different models. I'll buy the housing for TYTN to be sure it fits.
Wonder if they supply a instruction manual with it... Anyone knows?
The 8525 case that cnn.cn has for sale shows a front camera hole but no video call button which is something I would prefer, but where do you get the d-pad from? For those looking for a disassembly of the hermes have a look here on the wiki.I think there could be a really good combination of part to make a really nice looking hermes.
Dangnabbit.
I just ordered that Black Housing, but didn't notice the lack of a video call button. I hope it wont matter during installation on my Xda version
I've replaced the housing on my Vario ii for that of an SPV M3100 with no problems whatsoever - it was really quite straightforward. I kept the t-mobile directional pad as I preferred the look of it.
Changing the housing on a model of hermes with a different layout however is not so straightforward as it involves not only changing the keypad itself but also the little pcb underneath which is slightly different between Herm models.
it is certainly possible to replace the slide mechanism, keyboard and backplate between ANY model of Hermes, and some nice combinations are possible. I have a vario ii orange backlit keyboard if anyone wants it.
chinaonnitrous1!
Let us know how it went
Thanks!
they carried 2 housing...the only different is the key pad layout...so pay attention to the key pad...
This company is very slow in responding to email. I send them 2 email about a week ago asking for shipping date...yet no respond
Thats interesting, I ordered something from them on thursday, I got an email withing hours saying it had shipped with a tracking number...
As for the keypad layout, if you wanted to use the Black case you would have to also find the keypad to match it, as well as the PCB that goes beneath. cnn.cn has the parts for the TyTN, but not the 8525.
Maybe someone with good dremel and case modding skills could make it look good though.
Does anyone actually have the Black HTC TyTN that they were supposedly shipping? I was going to get one, but then everyone convinced me not too, I'd be interested to see some pics though.
I'lll get the housing withhin a week.
I'll post pics and everything.
chinaonnitrous1 said:
I'lll get the housing withhin a week.
I'll post pics and everything.
Click to expand...
Click to collapse
Thanks mate!
chinaonnitrous1 any news on how it went ?
I bought from http://cnn.cn/shop a case for 8525 and the external keyboard because I have a SPV M3100. I am waiting for the package and I'll put some pictures of the case. I hope the quality of the case is ok.
I just received my new TyTN case from cnn.cn. It is a dopod branded case, slightly different colour than my original TyTN case. I guess I would call the colour "graphite".
It is definately an original case off of a phone, it still has the old IMEI and Serial Number on the sticker on the back.
Build quality is good, it doesn't look like it is off a used phone. One thing I noticed however was that the silver metal on the front was slightly pulled up, and there were some adhesive remnants on the side of the case. I'm sure it will clean up fine with a little solvent though.
I haven't replaced it yet, I am waiting on a new keypad circuit board (mine is fried, you have to push it ridiculously hard to get it to work), and I will open it up then and replace everything.
Ordering from CNN.CN was pretty good. Shipping was $5 CAD, and it took about a week and a half to arrive. A signature was required, but there were no fees or duty.
leoni1980 said:
it is certainly possible to replace the slide mechanism, keyboard and backplate between ANY model of Hermes, and some nice combinations are possible. I have a vario ii orange backlit keyboard if anyone wants it.
Click to expand...
Click to collapse
Hi, I'd be interested in the keypad, if it's still available? I've dropped my VarioII and the keypad is slightly bent lol
where did you get the replacement body from?
Cheers
Hi,
Has anyone purchased one of the HTC 8525 OEM housings from cnn.cn. If so what was the quality like and are they new housings? None of the re-branded TyTn's seem to use this housing so I'm wondering if they are manufacured specifically for, or by, cnn.cn?
Also, what are the service and delivery charges like from cnn.cn.
http://cnn.cn/shop/8525-full-housing-pi-198.html?osCsid=ee042fbf3e01db3c5bad7913ecdb4a44http://cnn.cn/shop/8525-full-housing-pi-198.html osCsid=ee042fbf3e01db3c5bad7913ecdb4a44
Thanks in advance.
I bought a blackberry case from them and it arrived in 8 days. Great service for 5 USD in my opinion.
I'm curious about that tytn housing unit too.
They have taken it down for some reason.
O was gonna try it.
sjbale said:
Hi,
Has anyone purchased one of the HTC 8525 OEM housings from cnn.cn. If so what was the quality like and are they new housings? None of the re-branded TyTn's seem to use this housing so I'm wondering if they are manufacured specifically for, or by, cnn.cn?
Also, what are the service and delivery charges like from cnn.cn.
http://cnn.cn/shop/8525-full-housing-pi-198.html?osCsid=ee042fbf3e01db3c5bad7913ecdb4a44http://cnn.cn/shop/8525-full-housing-pi-198.html osCsid=ee042fbf3e01db3c5bad7913ecdb4a44
Thanks in advance.
Click to expand...
Click to collapse
Dude you got a TyTN or an 8525?Because are very different..
I havent heard many bad things about them, havent used them personally yet
8525 Housing
I might as well just add to this thread
You guys think this is worth a shot? The last owner of my phone jacked up a couple parts of the current housing.
http://cgi.ebay.com/HTC-Magician-qt...yZ108649QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
g35driver said:
I might as well just add to this thread
You guys think this is worth a shot? The last owner of my phone jacked up a couple parts of the current housing.
http://cgi.ebay.com/HTC-Magician-qt...yZ108649QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
Click to expand...
Click to collapse
That'd look great on the 8525. You may want to check this out for a step-by-step guide.
http://www.howardforums.com/showthread.php?t=1152710&page=1&pp=15
Judging by it's looks, it only works with Hern100 devices (8525, m3100, etc) and wont work with the TyTN. (herm200)
I could be wrong though.
The D-Pad layout is a bit different, but if you get the D-Pad
http://cnn.cn/shop/cingular-8525htc-hermes-outside-keypad-p-1610.html
and what goes under the D-Pad, you might be able to get it to work.
But that's kind of not worth the effort though.
I am yet to find a stylish housing for my tytn. It's all scratched out but I hate that Dopod housing.
Since there is no flipping way, HTC is going to make the original housing available to anyone, it would have been nice if someone came out with a more stylish design.
g35driver said:
I might as well just add to this thread
You guys think this is worth a shot? The last owner of my phone jacked up a couple parts of the current housing.
http://cgi.ebay.com/HTC-Magician-qt...yZ108649QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
Click to expand...
Click to collapse
I'd love to pick up an all black housing like that but it has one thing that keeps me from doing it.. the front facing camera hole. since i have an 8525.. it would just be an open hole on the front of my phone which would look dumb and get lots of dust inside.
g35driver said:
I might as well just add to this thread
You guys think this is worth a shot? The last owner of my phone jacked up a couple parts of the current housing.
http://cgi.ebay.com/HTC-Magician-qt...yZ108649QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
Click to expand...
Click to collapse
I have one on the way..
is it really hard to get the original HTC grey version? I've seen loads of the dopod versions, some with some without the video button.
http://cgi.ebay.co.uk/ws/eBayISAPI....m=290143857315&ssPageName=STRK:MEWA:IT&ih=019
is htc but dont know if button configuration is right for hermes 200 (Anyone confirm this?) does that have video button??
http://cgi.ebay.co.uk/ws/eBayISAPI....PageName=STRK:MEWA:IT&ih=015#ebayphotohosting
Its the closest one ive seen to mine but branded CHT DOPOD
Ive seen people ask htc to replace it but had no sucess. Its really annoying considering we all dont keep the phones forever and selling them off is harder when you cant get the original housing replaced.
that black htc housing DOES have the video button but the layout is different than the herm200.
the red hangup button and the green phone button are not on the right place on that case.
I have taken my tytn apart. What goes under the D-Pad in herme200 looks different than the ones in herm100. Even if you did get that case and the right d-pad, your buttons wont fall on the right spot. therefore the phone button and the hangup button wont work.
I wonder if HTC repair center would replace the housing.
check this post
http://forum.xda-developers.com/showthread.php?t=323520
Ok, so as the title suggests, i'm looking at replacing the housing of my vario (cause its scratched to hell - keys in pockets, and the odd drop )
After looking at http://cnn.cn/shop/8525-blacksilver-full-housing-p-198.html was wondering whether these were suitable for straight swap? as obviously the keypads are different between the herm100/200/300 but i'd keep the original in as its in good condition, and wouldnt mean i'd need to swap the pcb underneath either?
Or am I barking up the completely wrong tree so to speak?
Any help appreciated...especially for you Vario owners who have changed their housings...any problems you came across etc.
Cheers!
bump surely someone must have done this already?? all these reads, and no replies
SEARCH THE FORUMS BEFORE POSTING THREADS
kthxbye =p
i've already searched....n yeh it mentions swapping with an orange 3100 housing...but thats something i'd haveto find on ebay etc...doesnt mention the 8525 housing on cnn..... so was wondering if the keypad fits or not, as the front faceplate is scratched to hell so would need to swap the whole casing...not just the middle/rear panels.
Try this: http://cgi.ebay.co.uk/OEM-Housing-f...oryZ3728QQrdZ1QQssPageNameZWD1VQQcmdZViewItem
Cheers for the link Paul. That listing seems to claim that you can replace a vario with that housing, so might aswell just bite the bullet and go for it I'll probably look at getting it from CNN still, as they will work out slightly cheaper (~£32 compared to ~£45)
marcparker said:
replace a vario with that housing
Click to expand...
Click to collapse
Vario II to be more precise. The Vario is a HTC Wizard.
Any success with replacing? Is it hard to do? I have some scratches myself, and would like to change the housing. Have a TYTN
I havnt had chance to order the new housing yet, as i was skint until payday I'm going to hopefully get it ordered within the next couple of days.... I'll keep you posted on how it goes!
Still no one with experiences?
On this site there is a GPS antena available for TyTn... can we then enable GPS on the TyTn??
http://cnn.cn/shop/8525tytnhermes-antenna-p-1615.html
I've seen an HTC Hermes Case on this site:
http://www.cellphonepartszone.com/Products.asp?shopxpbe_id=64&id=281
but it's not completely clear to me on how to order and pay... (i'm Italian)
Hope this will be useful and you'll understand how to order the case...
Still no one with experiences on changing the housing?
Sei semplicemente un grande..la cover originale è impossibile da trovare!!
However no succesfully experience to swap the housing because in order to be able to change them (Cingular/HTC 8525 and also from Orange but i can't remember the name) with a TyTN, because the internal keypad membrane of the buttons at the top of the phone are (hope for now) impossible to find anywhere. I'm still looking for..
Churchill said:
On this site there is a GPS antena available for TyTn... can we then enable GPS on the TyTn??
http://cnn.cn/shop/8525tytnhermes-antenna-p-1615.html
Click to expand...
Click to collapse
I think enabling GPS is a little more complex than that - there were some required connections on the chipset that are not connected - try searching this forum...
Before post remember the topic of the thread: HOUSING
not gps
After I had changed the housing the screen doesn´t change into landscape mode
Hi!
After I had changed the housing the landscape mode isn´t activate itself while openning the keyboard. It did only once. It seems like the problem is of physical matter but I checket out all again and it seems to be all as it was. I don´t have another complains about functionality.
For those who wants to change the housing I have to say that that takes alot of time. And before you will waist money for a new housing make the following steps:
1. Look a this one verry carefully and be sure you have all tools you need.
ftp://ftp.xda-developers.com/Wizard/Docs_Tutorials/Wizard_Service_Manual.pdf
2. Think that you will need some stuff that you will put between new housing and touchscreen. (I took the old one but it isn´t a good idea).
3. You will need some glue to glue the old parts to the new housing (obviously the housing is more than just this plastic case).
If somone could give me an good advice related to the screenmode while opening I will aprecciate that.
ecor said:
Hi!
After I had changed the housing the landscape mode isn´t activate itself while openning the keyboard. It did only once. It seems like the problem is of physical matter but I checket out all again and it seems to be all as it was. I don´t have another complains about functionality.
For those who wants to change the housing I have to say that that takes alot of time. And before you will waist money for a new housing make the following steps:
1. Look a this one verry carefully and be sure you have all tools you need.
ftp://ftp.xda-developers.com/Wizard/Docs_Tutorials/Wizard_Service_Manual.pdf
2. Think that you will need some stuff that you will put between new housing and touchscreen. (I took the old one but it isn´t a good idea).
3. You will need some glue to glue the old parts to the new housing (obviously the housing is more than just this plastic case).
If somone could give me an good advice related to the screenmode while opening I will aprecciate that.
Click to expand...
Click to collapse
Your device does not rotate anymore because you have not moved the magnet from the old casing to the new one. The magnet operates the rotate switch. See here:
http://forum.xda-developers.com/showthread.php?p=2686388
Mike
Oh and you gave a link to the Wizard Manual, but you can get one for the Hermes here www.mikechannon.net
Just saw this on ebay...Im a fan of housing and facia. But i know %98 of TP2 owner right now dont wanna touch the Hardware section of the phone.( for customizing)
It Just nice too see that we can tweak not only whats inside but also the outside too... Im just hoping for a nice fit and high quality. Its too early to tell how good this housing is but i wanna know soon.
http://cgi.ebay.co.uk/ORIGINAL-HTC-...s_JN?hash=item4cea1e075a&_trksid=p3286.c0.m14
I also noticed that a couple days ago but they only offer red and blue right now. I'm not savy enough but I think it's a cool options
For that, did you know how to dismount the TP2 ?
Looks like not really easy to operate at first glance...
You get a screwdriver with it ... just find all the screws and replace!
wait few months... dismantling this phone will be on youtube!
I noticed those when I bought my TP2 last week... to bad they are only red and blue. I would be down for black, or maybe a nice dark green. They look nice from the photo. I don't like taking apart slider phones... PITA
The Wing wasn't so bad. I did the whole thing solo since my brother broke his screen and there weren't any dismantling guides available yet. It's easier than you think... just don't force anything and keep a sharp eye open for screws.
The only problem with swapping the case for a T-Mobile version is that you have to keep the T-Mobile keyboard. The layout is unique to T-Mobile and the HTC version (as well as other carriers) vary from model to model.
freakingwilly said:
The Wing wasn't so bad. I did the whole thing solo since my brother broke his screen and there weren't any dismantling guides available yet. It's easier than you think... just don't force anything and keep a sharp eye open for screws.
The only problem with swapping the case for a T-Mobile version is that you have to keep the T-Mobile keyboard. The layout is unique to T-Mobile and the HTC version (as well as other carriers) vary from model to model.
Click to expand...
Click to collapse
It's really easy to swap cases. I had to replace the screen on my room mates Kaiser which is a slider tilt screen device as well. Took me 40 mins tops & I had to completely disassemble it. Will probably have to again soon. He broke his screen a second time lmao. The one thing I'll note though is for T-Mobile, the whole device is different basicly. The screen does have a tappered edge & the screen cover is bigger & the battery cover is a completely different design. the Stylus doesn't go through it. So, the T-Mobile wouldn't be completely changible. As for the keyboard, that can be changed via ROM. The HTC Kaiser has a different KB Layout than the AT&T Tilt, we just install a CAB to "fix" this as the ROM's are made for the HTC version. Also, the Sprint/Verizon/AT&T(From what I read) have Headphone Jacks. You could arguably use only part of the kit, but for $80-100+, I want one completely compatible with my device.
As for Colors, there's a full silver/full black/& black & orange version available. I wish they made them available in pieces so you could mix & match parts. For example the Battery covers.
Anyone knows whether a housing is available for the european version? Mine has some ugly scratches due to close contact with the asphalt Can't find a new housing though, only bezels... I need a new grey edge around the keyboard to which the battery cover is attached aswel. Is this even possible?
Luckily, the keyboard, screen and batt cover are still intact, and the phone is still functioning properly. It is now protected by a plastic rubberized case and a screenprotector.
Help would be very welcome!
I'm thinking about giving this a try to replace the screwed up button layout that ATT provided. If I can just swap the buttons and the remap the keys with a cab file I'm thinking I can get the QWERTY keyboard back to it's original form.
Anyone else tried this?
Jon
Tried going to the link but it appears to have been "removed".....anywhere else?
This one is working for me.
http://cgi.ebay.com/HTC-TOUCH-PRO-2-T7373-OEM-RED-FULL-HOUSING-KEYBOARD-US_W0QQitemZ350292809157QQcmdZViewItemQQptZPDA_Accessories?hash=item518f1415c5
Lets focus on getting everyone behind this one thread - maybe we can get someone to confirm! Thanks! http://forum.xda-developers.com/showthread.php?t=547632&page=4
Schmurtz1968 said:
For that, did you know how to dismount the TP2 ?
Looks like not really easy to operate at first glance...
Click to expand...
Click to collapse
Dismantling HTC Touch PRO2, HTC Rhodium in pictures...
The above dismantling link has been in the XDA-Wiki for several months now.
So what? If someone asks a question and I can help, I sure will. Or should I be an smartass and tell it's around here, use the search... Maybe it's your thing, not mine.
i'd like to try to replace the bezel on the screen-part, it's got little wholes and even a completely crushed section.. but according to the link you'll have to disassemble the whole keyboard-part in order to do that.. isnt there an easier way to replace the bezel??
just wanted to let everyone know that I have the black/blue case from ebay china. It took 3 weeks but I finally have it.
After taking apart my g1 and 90% housing conversion from white to black. I accidentally cut one of the ribbons off and broke the phone. So im a little scared to take apart this $400 phone. Didnt mind the g1 because there dirt cheap and easy to find another one.
If you all can gather some links and any guides I will probably convert my tmo tp2 to the new housing sunday mourning. unless someone can confirm that its extremly easy to switch housing.
Just an example of the g1 dissemble.
http://www.youtube.com/watch?v=3PdhXx3g9nU
ive been modding hardware since everyone had a nextel i730. ive seen alot of crappy poorly made housings in my days. usually the first and second generation batches of housings that come out are poorly cut, or made of brittle plastics. i would advise that when looking for housings(especially for expensive devices), that you get a 3rd generation housing and look on youtube for directions.
So excited.
I am trying to covert my T-mobile touch pro 2 soon. The full housing will arrive in 2 days. I dropped my precious on the pavement.... T-mobile housing is nowhere to be found so I bit the nail. Hopefull it's going to turn out awesome
Check this one for taking apart. flickr.com/photos/[email protected]/sets/72157621828152091/
Hey guys,
My white unlocked Hero has sustained some nasty body scratches plus it is starting to turn yellow. I'm considering a full body replacement. I was only able to find this:
http://cgi.ebay.com/GENINUE-HOUSING-FACEPLATE-FACIA-GOOGLE-G3-HTC-
HERO-WT_W0QQitemZ280402919652QQcmdZViewItemQQptZPDA_Accessories?hash=item41495100e4
Do you think that it's going to be as good as the original one? The seller claims that it's genuine, What do you think?
I found a site that has both the black and white housing for the gsm hero.
http://www.truesupplier.com/faceplate-housing-cover-for-htc-hero-g2-touch-white-color-pr-18489.html
How do I know that it's genuine? or at least as good as the original HTC cover?
slimfady said:
How do I know that it's genuine?
Click to expand...
Click to collapse
The web page is called "truesupplier.com". OF COURSE its genuine
How hard is it to change the housing anyway?
by changing housing you will probably break phone trust me ... and truesupplier housing is oem not genuine by looks of it..
He might not break it if he's careful, and has the proper tools. I've taken apart a few phones without causing any problems.
So unless i'm handy at doing these things, I should not do it myself?
What if I have our local HTC agent do it? Will it at least look as good as new?
i have the white hero and would love to put the black case on it.
the site mentioned above says it comes with the tools needed to change the cover, has any tried doing this?
i would love to go for it but don't want to f*&k my phone up!
i think its not so difficult to switch the cover if you take off the backcover there are 6 screws than open the case from the top of the mobile phone and pull it off
but becarefull maybe there are flatcables from die lcd or the trackball just make it slow and be carefull all the time
and maybe you can find a dissembly how to in google
peace
this site has pics of disassembly of a hero but it's in russian.
http://www.pdacenter.ru/razborka/htc_hero/
If you have to pry the phone open use something plastic so you dont damage the original case. Just in case the ebay housing is rubbish.
hawwy said:
by changing housing you will probably break phone trust me ... and truesupplier housing is oem not genuine by looks of it..
Click to expand...
Click to collapse
whats the difference between oem and genuine
any1 bought replacement white hoising? mine is getting yellow. so need to buy a back cover.
Thinking of buying one myself. I accidentally dropped mine on the tiled floors of my workplace toilets LOL (luckily not IN the toilet). so now there's a little nick on the top left corner of the case.
If this is your first time you will probably scratch the covers but nothing more. You need to be very patient and i will suggest take a look to a good tutorial.
iopened my hero 1 week ago and its so easy maybe in the next days i will upload a video in youtube
bye
I bought the ebay one. It's surprisingly well built (Not Teflon though).
The sad part is that my touch screen got screwed up during the installation. The bottom part of the screen is no longer functional and the sensitivity is messed up overall. Did the replacement in a local phone shop.
Now trying to find a way to fix it.
gyounut said:
iopened my hero 1 week ago and its so easy maybe in the next days i will upload a video in youtube
bye
Click to expand...
Click to collapse
That would be greatly appreciated!
hmm do you want to sell me your backplate of your old case? i need it please
and to fix your problem : you need a new display glas with digitizer
to remove your old glas: use a hairdryer, you have to heat up the old clue of the old glas and than you can push it easily out of the frame but be carefull not to heatup the frame, the plastic can deform, maybe you can cover it with aluminium foil from the kitchen
the video of the dissembly will be uploaded tomorrow by me
good night guys!
slimfady said:
I bought the ebay one. It's surprisingly well built (Not Teflon though).
The sad part is that my touch screen got screwed up during the installation. The bottom part of the screen is no longer functional and the sensitivity is messed up overall. Did the replacement in a local phone shop.
Now trying to find a way to fix it.
Click to expand...
Click to collapse
Where can I find new display glass for HTC hero? or can I just buy something generic?
I don't mind giving you my old backcover though it's in a very bad shape (which is why I wanted to replace it in the first place).