Hey Brothers
I Have a HTC Blueangel Orange SPVM2000
I have Broken My 2.5 mm Headset Audio Connector
& The Tracks on Mainboard also Broken
Plz Send Me the Schematic Diagram for Mainboard of Blueangel.
plz PM me or Mail me on [email protected]
hi...
if you want, i have a blueangel to sell...
it's perfect, except a broken flat-cable of screen, and one of sliding mechanism of housing cover... if you are interested, or you know someone that may be, contact me there or at [email protected].
bye
hello guys ... I have a problem with my Blueangel need the Schematic Diagram to repair a problem with the keyboard or lines (q, a, z) is not working and I tried the keyboard is fine. but card problem .. I think they burn lines (q, a, z) please
maybe a look into the bluangel service manual (in my signature) will help you.
Related
All parts used, and in good condition (if not other mentioned):
(maybe i am doing someone a favour, i know how hard it is to get on the spare parts )
-Mainboard with WM2003SE Beta
-Accu (ca. 8 Month old)
-TFT Display
-Buttons, Antenna, other Small parts
-Stylus
-Stereo Headset with Microphone
-USB Crandle with AC/DC Adaptor
-Charging Adaptor
-Leather Cases (1x Original, 1x Horizontal good Quality)
-well worn Cover (when someone Buys Mainboard or Display, he can get it for free)
-Original Packaging
I also have a lot of SpareParts for older Sony, Ericsson, Siemens and Nokia Phones...
Greets, Michael
I am in Germany, Shipping to EU will be no Problems, other Countries, please ask!
hi do you still have the pda?
i am interested
how much do you ask for it?
[email protected]
thank you
hey am also interested. one of the pda's - xda 2 to be more precise do u have one of those.
please reach me on this address
[email protected]
still for sale... please mail: irgendwo @ o2online.de
Hallo,
I'm interested too.
How much the set costs ??
how's the casing? if it's still good, i'm interested.
[email protected]
i live in singapore. are you able to ship there?
interested
Hi,
I'm interested, how much is the whole lot if still available?
my email is: [email protected]
Motherboard Needed
TFT DISPLAY NEEDED
Email Me : [email protected]
Thank you :lol:
Phone Jack on a bad motherboard?
I want the Phone Jack part from a bad motherboard.. Does any one has it?
How much would you like for the stereo headset?
hi, does any1 know where to get the plastic service tool for the xda 2 ?
or what else can be used just as good ?
also any1 know where to get parts ie speaker ? mic ? or battery connector ?
i think the actual part is called the sync connector ?
cheers
ok, i dnt need the plastic service tool anymore, but does any1 know where to get spare parts like the speaker or mic ?
also does any1 have any ideas on how to solder the 22pin battery/sync connector ? or where i can get it done ?
cheers
I have a vast stock of all ORIGINAL xda/xda2/xda2i accessories. Need anything email me or see me on ebay...
cheers
computerchid
I am not spamming just realized my first post wasnt clear
other post
Well after 1 year of use and abuse.. i manage to produce the first phisical damage to my Blueangel
Just received a Car mount with external speaker and while fiddling with it the suction cup lost grip and the whole thing fall off the table (1mt +or-)
Well the mini jack for the hands free (which at that time had connected an enormous plug to convert 4pins 2.5 mm to 3.5) got torn off from the soldered points and was completetly loose... So hands on i managed to open the darn beast with a jewler tool set and much to my relief the 10 pin's connector (only god knows what they're for) has enough space to use my soldering iron to fix it back...
The problem was that one of the contacs in the board got torn off and for much i tried to recreate i think i didnt succeed as i only have audio from the headset now and not from the phone itself...
I am posting as maybe one of you guys could provide a connection diagram for the darn think so i can try to isolate the problem.
Please dont let me down...
Cheers
N
Found it (well mostly)
Found in the Wiky this: Pinout!! , for the wallby and altought on the BA is 10 pin the position seems to be right.... only 6 pins used ??? or was I lucky ??? I dont care... tried to isolate the problem by testing continuity on the pins that work for the wallby and one of them (the one that was destroyed ) was not giving it..
a lot of patience soldering iron and support from my wife.. i managed to create a bridge and now it works!!!
cheers....
Thanks
10-4
i have htc tytn herm100
from a couple of days i had a problem that during a call mic of tytn stops working
then i run rescue audio recorder(coz it displays the voice meter)
then try to hit lighty with a pen or finger near the mic
then it starts working.......
yesterday i opened tytn
and cheked that there is a four pin mic ( i think a mic and preamplifier is built in it)
one pin is ground
other one has 2 volt on it...
fortunalely i have a Imate Sp5m dead in my stock.....
so i opened it there was the same mic but a different text written on it...
so i replaced with it,,,,,,,,,but no voice........
i have also solded 4 wires to te points and make them as long that they could reach out side the tytn
then tried ordinary mics as well.
but not worked
now i m in big trouble.......
and using only blue tooth handfree .................
plz help me if any solution or any diagram
plz plz plz plz plz plz
crap i had this happen on my wifes prophet, hope it doesnt do it on my hermes too.
im guessing you cant do a warranty repair?
no i cant get warranty coz i have got it used ..only set no warranty
so i have to repair it my self
plz help me friends
me too, but my hermes has a problem not like u
his mic is also work, but when I flash a new rom , it's work normally , but after that it's work very small , my recorded work small , I don't know why,who can give me advise.thanks.
I had a broken microfone on one of my 5 hermes (yes I have exchanged it 5 times in less than a year!). Luckly I do have warrenty so I got mine replaced, but I dont think it was actually my microfone which was broken. The USB looked broken so I think I had a short in the USB port leading the phone to believe that a microfone was plugged in, therefore disabling the inbuilt one. You might want to give that a look into.
i also think that this is usn socket problem
coz it was started from the usb port
Hi everybody
Sorry for my english, isn't my native language
For some problems on my radio i had to buy a main board to KGL on internet and they sent me one "new", but no was so, it was repaired unit and had some problems. so i claimed to paypal to help me and while i was waiting for the answer kgl tried to help me to repair the broken mainboard and sent me the material that i share here.
finally my problem was on TFT board (1 resistor died) and paypal refund me the money, and today i'm very happy because now i can listen MY music after 5 long months.
Maybe we can see something that can be improve to get a better radio(sound, signals, etc) and is easy track the routes with this software.
i tried to upload the software to open the pcb but i cant, so the program name is PADS9.5, try to download it from google
https://www.pads.com/downloads/standard-eval-request
i call @Digo69 to explain us how to made the mod he told here http://forum.xda-developers.com/showpost.php?p=67892872&postcount=464
thanks
@7floor take a look
i had been looking on pcb file the bluetooth mod and i think is no needed, take a look on yellow tracks, the radio has done the mod, the problem is the kind of jack for the micro because the original mic jack is a 3 pins, which 1º pin is groud, 2º pin is the mic for bluetooth and tracks go to c32 and c32 go to pin 4 on bluetooth module (pin 2 pic) and 3º is mic for system (pin 3 pic), i only can see two separated ways for sound inputs.
maybe c144 do some modification on bluetooth mic, because it's connected to c32 (jumper) pin 4 on bluetooth module and ground
we only have to use a 3 pin male jack (stereo) and use an aftermark mic usin pin 2 + and pin 3- pin1 no connected (only for bluetooth mic in) or pin 1 and 2+ and pin 3- for both mic in
what do you think?
look
elcolombia17 said:
Hi everybody
Sorry for my english, isn't my native language
For some problems on my radio i had to buy a main board to KGL on internet and they sent me one "new", but no was so, it was repaired unit and had some problems. so i claimed to paypal to help me and while i was waiting for the answer kgl tried to help me to repair the broken mainboard and sent me the material that i share here.
finally my problem was on TFT board (1 resistor died) and paypal refund me the money, and today i'm very happy because now i can listen MY music after 5 long months.
Maybe we can see something that can be improve to get a better radio(sound, signals, etc) and is easy track the routes with this software.
i tried to upload the software to open the pcb but i cant, so the program name is PADS9.5, try to download it from google
https://www.pads.com/downloads/standard-eval-request
i call @Digo69 to explain us how to made the mod he told here http://forum.xda-developers.com/showpost.php?p=67892872&postcount=464
thanks
@7floor take a look
Click to expand...
Click to collapse
Can you ask for them to send you schematics? These are board designs, somewhat useful.