Related
I installed the dcd USCC Carrier 20080801.cab on my 6.1 rom, and the data connection still will not connect. Dialing #777 with no user name/pw/domain, and it still fails.. is there a newer cab? I am in Maine.
Thanks.
Call provider ask them to reset your DMU keys. You may also need to blank yours out. ##778 under the MIP Default Profile HDA and AAA. Should look like encrypted text.
-1
I had an HA and AAA, with encrypted text, cleared both.. calling operator to reset now, cuz my resets weren't enough to fix it.
Ugh, operator says there is no way to reset dmu keys..
Did you by any chance back up your phone programming with QPST? I did to be safe, but luckily did not have to roll back to it after programming the phone.
If they get you back up and working, or end up replacing your phone, use QPST to back up service programming so that in case this happens again, you can restore it and not lose data.
What steps did you do to upgrade?
I had to use the registry change to get my SPC, then used QPST to back up my service programming.
Ran the bootloader 2.40, installed radio 3.42.30, then DCD 3.2.3 and everything went smooth, the cab file pretty much contains the USCC theme, and possibly a few tweaks, but it does not contain the info to restore the data services as it's a unique encrypted ID that should be unique for each subscriber. The only way to get it back is from a backup, or from their customer service.
I imagine if you can take it to one of the stores that has a tech onsite, he could put the info back in for you, however, he is gonna probably be rather upset that it's not their rom on it, and may refuse to work on it. Maybe at first you can call and ask to speak to their technician, maybe he will help you over the phone, just depends on the tech.
Good luck,
BTC
I have a friend with a motoq with same carrier.. can I pull the settings from theirs?
will research spl and qpst, any good recommendations before I go down a wrong path?
I believe the settings are unique to each customer, so while he will have settings, they won't be yours. I suppose it's possible his might work on yours, however if it does, then he will get billed for any data you use. Since his is unlimited as well, it wouldn't probably cost him anything, but it wouldn't be correct, and may cause him issues later, so I would recommend against it.
You really need to get a tech on the phone who has intimate knowledge of this phone, he should be able to get you the settings you need, but I'm sure he will want to know why it stopped working... Maybe someone else here can give you a plausible story that you can give him for why it got erased.
BTC
Sometimes activating and old phone, make couple calls and re-activating the 6800 works for resettting those keys.
I have QPST, but no phone is showing up. Can't find a good thread on using qpst. My friend is willing to share his data connection information, if I could figure out how to extract his and put it on mine.
MetalHd said:
I have QPST, but no phone is showing up. Can't find a good thread on using qpst. My friend is willing to share his data connection information, if I could figure out how to extract his and put it on mine.
Click to expand...
Click to collapse
Look for GC's GPS Fix wiki, it has good instuctions on how to get QPST to see your phone.
BTC
Well, I got lucky, I hope.. I called Data Services at USCC today, and the HTC and WM reps were on site.. I got the tech to get a stock 6.0 rom, supposedly coming via email.. then I can start over and do it right this time?? !!!
If they send you the rom, please let me know, many many many of us would appreciate having a stock rom available to reflash our phones. Hopefully it will flash all the ROM so that it doesn't make the phone worse. Several people said that there are settings that don't get erased when flashing a rom that could cause problems. So if you get it and it works, please share the file with some of the developers here so we can get it available for download for those who need it.
BTC
MetalHd, did you ever recieve that ROM? If so is it posted somewhere?
Sorry, never got a rom.. they sent me a new phone.
Did they give you any problems about flashing the phone?
Before trying to upgrade this phone, be sure to learn to use QPST and backup your phone programming, then after flashing the radio and your first rom, re-run QPST and write the programming back to the phone. Then the cab will restore data every time you flash in the future.
Also you can do the aGPS update and make GPS work perfect on the phone.
BTC
#3
record your EPST information just incase you end up like i did with the data connection not working.
Optain this information by
start<programs<file explorer<my device<windows
tap on EPST file. (should be the 28b one if you have 2)
Choose View
tap view info (left soft key)
tap M.IP Settings
The following should match,
M.IP SETTINGS
Number of Profiles : 6
Active User Profile Index : 0
MIP_MODE : Mobile IP Prefered
MIP Registration Retries : 1
MIP Registration Retry Timeout : 2000 ms
MIP Pre-Registration Timeout : 3
Mobile Node-HA Authentication : Enable
Send a Registration Request Only in Use : Enable
Dormant Hanfoff Optimization: Enable
View info<M.IP Default Profile
M.IP Default Profile
Enable Profile : Enable
NAI : **********@uscc.net (*'s are your ten digit MSID number)
MN HA SPI Set : Enable
MN HA SPI Value( Hex ) : 10E1
MN AAA SPI Set : Enable
MN AAA SPI Set Value ( Hex ) : 2
Reverse Tunneling Preferred : Enable
Home Address : 0.0.0.0
Primary HA Address : 255.255.255.255
Secondary HA Address : 255.255.255.255
DMU public key(PKOID) : 41
Hit ok
Bring up "Phone"
Dial ##000000
tap talk
Record
MDN : **********
MSID : **********
Home SID/NID #1 : ***/*****
taken from Here
i had the same problem when i went to the gps radio and this fixed the problem
This is for people who want Cricket to work perfectly, just follow these instructions not skipping a beat and you will be OK from then on! If you are not having problems obviously skip this!
I have updated this thread ONLY to Change a step. Its not a Required Change for current Cricket users however, it may be needed for Phones that have never been on Cricket before. I also re-phrased some things to be more understandable.
This thread is assuming that you already have your phone Unlocked (spc code all zeros) and that you have already contacted Cricket and had the Phone you are programming added to the Account. You might as well tell them you have a Motorola Razor V3C that will ensure there will be no problems obtaining EVDO.
Also ask Cricket for your MSID/MIN number (usually not your Phone Number) we will be needing the MSID/MIN if you dont know it, or if the phone was never on Cricket before.
My HTC Unlock Tools Directory, Read SPC Instructions Readme
My Cricket WAP and Arcsoft new versions or my Cricket Carrier CAB <--If you are installing one of my Cricket CABs dont test it until your PST settings are correct.
This thread is also assuming that you already have a CRICKET PRL file loaded in PST. If you have my ROM flashed than a couple PRL files that you can use are on device memory we will get to that later below.
Important note on PRL files. You must know what kind of Cricket Plan you have. If you have Roaming on your plan you need to use the 5 digit PRL files. If you DO NOT have Roaming on your plan you must use the PRL files that are considered 4 digits or contain a 0 at the beginning. Otherwise *228 will not work and you will not be able to Authenticate. Some report for users with roaming you may have to use PRL 1042 and set your SID to be able to *228. Examples below.
PRL 01013 = Non Roaming
PRL 38515 = Roaming
1. Now first thing you want to do is have a good Cricket CAB or ROM installed. This way when the PST settings are done they can be looked over again, and tested.
2. Now if you are starting from a fresh flash OK, if you are starting from a hard reset OK, we can continue. If you have a ROM installed that is having problems I recommend a hard reset and skip Auto Customizations using stylus when it says you have 3 seconds. If you are confident the ROM you have installed is ready to go then fine. We can continue.
3. Now open your Phone Application and go to options and make sure smart dial is off. Then dial ##778 call button (PST/EPST), now click edit and enter six zeros. In the Main Page change the NAM name to Cricket, and enter the MSID/MIN number (that you obtained from your old Cricket phone or from Cricket themselves) make sure its a 10 digit number thats in your area code BUT IT IS USUALLY NOT your PHONE NUMBER. If it was already fine we can continue, if you dont know it you may of skipped obtaining this from calling Cricket as stated above. Now click view info and goto PRL, now check to make sure you have a CRICKET PRL (1013,1014, 1040, 1050 etc.. there are others) If you dont have one loaded in PST and you are using my ROM then you can click in Update PRL File (click in the blank area under setting) and then click Menu, edit, browse and it should go to main root (my documents). Pick PRL 1050 (You may have to try another PRL for *228 to work in step below). Then click ok, then Menu, then ok, it will ask you if you want to update the items click ok. Let it do its thing and restart. If you already have a CRICKET PRL then skip the update PRL step but still make sure to click menu, then ok and let it restart.
4. Now after the phone restarts open phone application again and dial *228 call button (this will make sure base settings are good so i will not have to explain as much, it will also download the proper local EVDO prl to where you are), it will dial cricket and do its programming thing. Do not interrupt this. Let it do its thing even if it restarts. It should say Update complete or Programming complete (if not then try a different Cricket PRL) Now when you are back in action we can continue.
5. Now open the phone application and dial ##778 call button (PST/EPST), now click edit and enter six zeros. Now click view info and goto AKEY and make sure its blank, nothing there. Now click view info and goto NAM settings, NAM name should be Cricket, Mobile Directory number should be YourTenDigitPhoneNumber, MIN1 should be that other phone number the MSID/MIN that is usually not your phone number, but it should be 7 digits, ex: sevendigitnumber, MIN2 should be just your area code. MSID/MIN should be 10digitMSIDnumber <--again usually not yourphonenumber, This part I only know for USA users MCC should be 310, MNC should be 00 (for other Countries you have to look this up), NMSI should be your MSID/MIN (XX10digitnumber<--usually not your phone number) THE XX'S should be zeros, ex: 007185548692, Now if all these settings in this paragraph didnt need touched assuming you didnt skip any of my steps (which they shouldnt be touched i am just making sure) we can move on.
6. Click view info and goto CDMA settings, we are going to make sure they are set right and change a couple things for Clearer voice transmissions, people will compliment how good your phone sounds even in some cases. EVRC should be set at Disable, Home page should be Voice 13k, the Two below it the Same Voice 13k.
7. Click view info click modem settings, change slot cycle index to 1, This will make the phone ring a little sooner, also get your texts a bit sooner. The other 4 options should be Auto, Auto, Enable, No in Order from top to bottom.
8. Click View Info and pick Security, now we are changing this regardless you must do this, we are going to Unauthenticate you and Re-authenticate, it is a Needed step everything in this How To needs to be done and Not skipped! Change the HDR Auth User ID to something bogus like [email protected], the password below it make it something random but remember it, now do the same for PPP user ID and password but make them the same as the HDR ones.
9. Click view info and pick MIP Settings, Make sure Active Profile is on 0, MIP mode should be Simple IP only, MIP reg retries should be 1, MIP reg retry timeout should be 2000 ms, MIP pre-reg timeout should be 30, Mobile Node HA auth should be Disable, send a reg request should be Enable, dormant handoff to disable.
10. Click view info and pick MIP Default Profile, Enable profile should be ENABLE, NAI should be [email protected], MN HA SPI set should be enable, MN HA SPI value should be 12c, MN AAA should be enable, MN AAA SPI value should be 2, reverse tunneling should be enable, home address should be 0.0.0.0, Primary HA address should be 68.28.15.12, secondary should be 68.28.31.12, HA shared secret and AAA secret should be cricket <--lowercase, DMU public should be 0, MN Authenticator should be 0.
11. Click view info and pick MIP customer profile 1 and make sure Enable profile is DISABLED. Now do the same with the other 4 profiles (profiles 2-5), make sure that the only profile enabled is MIP Default Profile.
12. Ok now click menu, ok and let it reset, but make sure not to do anything we are going to be going right back INTO EPST, so when it boots back up open the Phone application and dial ##778 call button (PST/EPST), we are going to re-authenticate you its easy, now click edit and enter six zeros, click view info and goto Security, now change the HDR AN Auth to [email protected], password should be cricket<--lower case, same for PPP user id and Password make them same as HDR.
13. Click view info and goto MIP default profile, make sure the HA, and AAA shared secrets are both cricket<---lowercase, then click menu OK and let it reset.
Thats it! PST settings are perfect for CRICKET, you have a Local EVDO prl file installed, and you are Authenticated for Data and EVDO, now if you used my ROM just go to internet explorer and goto a real page, and follow instructions but remember to click save password! You can also go back into the Phone Application and turn smart dial back on if you choose.
Thats done, every Custom ROM flash from now on should never affect your PST settings and you should always be Authenticated. I hope this helps everyone.
Ryan Mogul
Good write up for this. I have one big problem. when I try to *228, it fails after just a couple of seconds and says,
“The number of SPC attempts failed 15 times from the network. Handset will free for 1 minute and will then reset.” I read a post that was obscure but said that the SPC should be six 0's Mine is not all zeros. I don't know how to change mine to all zeros if that is the case
Thanks
That is the case, for *228 to program your SPC code needs to be all zero's or all 3's (make it zero's though) just follow My Unlock pack and Instructions, it guides you through changing your SPC to all zeros.
Cheers.
RECOGNIZE
Qpst will not recognize my phone
thanks for the great info. as a note, changing the EVRC setting (#7) to 'Voice 13k' kills my phone connection; i couldn't make or receive calls. everything else seems fine!
About Voice 13k Settings
Read the settings again, maybe you missed something.
Check these four settings, also make sure you have used *228 and let it UPDATE your PRL, don't do it manually afterwards. Then check all of the above settings over again and you should be good. I have researched, tested, and used these settings for a long time.
EVRC should be disabled
Home Page should be Voice 13k
Home Orig should be Voice 13k
Roam Orig should be Voice 13k
Since your phone is digital, it uses a codec to determine how the voice data is compressed into digital. Voice 13k (Qualcomm's Purevoice) is the highest voice rate. EVRC (Enhanced Variable Rate Codec) benefits the carriers because it uses a reduced rate, which means less bits to stream, more calls to go around. Voice 13k is in fact the updated version of EVRC that our Digital phones have the option to select from. Voice 13k should be enabled for optimal voice quality.
Take Care
heres why your *228 doesnt work for you..
This is for the User Vickie that needed a little help.
In order to use *228 for Cricket You need to have a Cricket PRL already loaded on the Device meaning installed from PST. You also need the phones SPC code to be all zero's (000000) Then *228 will work fine. It will then update your settings and DL a new PRL if a better one exists. This is for Cricket. If that works out you can follow my settings over again.
hey ryan i have installed your V1.1 Heavy Cricket rom, works great, thxs a lot
neways i was going trough this and i did every step to the letter, now mine didn't work... so i have to ask you a few questions...
first, once i am done with this, and if i did it correctly, i can now make calls and internet right? (hopefully this is yes...)
ok so assuming the answer to the above is yes, then i have to ask.
On step 3, you say if we have your ROM we can just update the PRL from there and to skip the "update step". by update step i'll assume you meant step 4. but then in step 4 you say "for both people who had to restart and people who didnt" and then you say to dial *228
so do we do that even if we already have your PRL loaded?
or do we never have to dial *228 if we have ur prl file?
also, on the profiles, in the M.IP settings, my phone had "6" profiles by default, should i set it to 5 like yours or what?
ok i got everything working beautifully, thanks for the instructions... it's just that i wasn't supposed to dial *228, and i did
anyways, my internet works, and holy cow i get bursts of 2mbps!
well one last thing i gotta ask is... so my calling doesn't work, so i have to call cricket or something to have them switch it to mine right?
on a sidenote, do you guys actually use IE? isn't there like firefox mobile or something??
PST settings are not the Only thing that matters for Internet(WAP) or for MMS. The ROM you are using also has to be configured properly for Cricket WAP/MMS to work. My ROM does but not everyone uses My ROM.
This thread will get your Phone's 1X and EVDO set up correctly. Which will ensure that if your ROM is configured properly that Calls/Text/WAP/MMS will all work. But this thread is NOT the only thing that matters. Read the end of my TOP post and it tells you what the Thread sets up..
Now for your other questions: In this PST settings thread Step 3 says that if you are using MY ROM and the phone doesnt have a Cricket PRL loaded in PST that my ROM has Cricket PRL's copied on it to Update PST with(after updating PST with Cricket PRL phone will soft reset).
This means that YES you need a Cricket PRL loaded(updated) in PST before dialing *228 and then it will restart and then on with the rest of the settings. Dialing *228 gets a local(to your AREA) EVDO PRL loaded in PST(which is downloaded from Cricket Realtime) and sets up base PST settings so that this thread is easier. It explains that in the TOP post at the TOP..
ok in the version of your ROM that i installed, which would be the V1.1 Heavy, it says in that post this:
"Messaging and Connections settings: <--Please do not mess with these as they are fine tuned for CRICKET!! It will always work perfect for you if you leave it alone I cant be responsible if anyone changes anything but you can always post your problems in this thread and I will be more than happy to help sort it out.
"
and this; "Fully working and tested Cricket WAP and MMS/SMS with no problems! I did a lot of tweaks to registry and provisioning to make this possible as the base I used(1.3.4) was originally meant for Sprint!! I pulled a lot of "All Nighters" put it that way lol."
so i thought i don't have to set up my MMS/WAP...
and do i still have to call *228??
***EDIT***
i just called *228, and they said: "sorry we cannot program your phone"
my internet still works... but that's the only thing that works so far, i can't make calls. or send txt msgs.
X-Kenshin-X said:
ok in the version of your ROM that i installed, which would be the V1.1 Heavy, it says in that post this:
"Messaging and Connections settings: <--Please do not mess with these as they are fine tuned for CRICKET!! It will always work perfect for you if you leave it alone I cant be responsible if anyone changes anything but you can always post your problems in this thread and I will be more than happy to help sort it out.
"
and this; "Fully working and tested Cricket WAP and MMS/SMS with no problems! I did a lot of tweaks to registry and provisioning to make this possible as the base I used(1.3.4) was originally meant for Sprint!! I pulled a lot of "All Nighters" put it that way lol."
so i thought i don't have to set up my MMS/WAP...
and do i still have to call *228??
***EDIT***
i just called *228, and they said: "sorry we cannot program your phone"
my internet still works... but that's the only thing that works so far, i can't make calls. or send txt msgs.
Click to expand...
Click to collapse
Ok if you dont understand it just give up. Please quit cluttering up this thread with YOUR problems. a ROM's settings and PST settings are two different things and they both need to be set up right to work!!
MY Cricket ROM is already set up for WAP/MMS, but not everyones version of a Cricket Rom is set up perfect. But your PHONE's PST settings still need set RIGHT as a ROM does not touch that!!
PST settings are independent of ROM settings.
Your problem with dialing *228 is because YOUR SPC CODE IS NOT SET TO ALL ZERO'S!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! SPC code needs to be all Zero's and you need a Cricket PRL loaded (updated) in PST before dialing *228!
It says that in the beginning of this thread. No wonder I am mad. Read well before you follow through
You people seriously have to learn how to read things before trying something. Read, read, read, read, read. Until you fully comprehend what you are trying to accomplish and THEN mess with things.
Edit: My threads are not meant to BABY STEP someone new through the entire process of unlocking, flashing, and programming a phone. NOT AT ALL.. The threads are meant to Help and that is what they do..
ok... wow there
look the reason why i was asking is because you only included this link in your ROM posting thread, you did not include any other links or procedures...
same here, you only include information to do one thing, i see no relevant information pointing to the "other settings" you're talking about.
EDIT:
i had already previously unlocked my phone with another program, but just to double check i used your unlocking pack and followed the instructions. when i run BAF MSL Grabber, it already gives me my MSL code as being 000000, so i am assuming my phone is already unlocked.
but i went ahead and tried to go trough with your thingy anyways, and i got stuck at the ##3424# thing. none worked, ##3424# nor ##3424
i had to use the DIAG(DRMRouter) that took me a while to find in your ROM and i am in QPST right now...
hey Ryan... actually everything works, it's just i was unsure if i still needed to "go down to the store" to get my phone line switched to this new phone with cricket...
neways everything works... including mms, internet, so on so forth. i just haven't tested the gps
Awesome man, I knew I would fuel your fire to get it working. Thats why I am who I am lol. My GPS works awesome. Alot of people dont know this but Agps works with my Cricket ROM. Take care.
Updated the PST settings
I have updated this thread to clear up any problems with New Cricket users that have never had Cricket before. I re-phrased a few things and changed a step so that both New and Current users will not have any problems.
actually about what i said in my last post, i never tested the GPS on the rom so i don't know if it works...
i just know that if i go to google maps, it never locks on to a satellite, dunno why
oh btw, i had to tell yah, the reason why i couldn't dial *228 is because at least in my area, cricket won't recognize the 1050 PRL. everything works with it, but it just won't let me do the *228 thing.
i had to use the 1042 PRL, and then everything worked, just a heads up.
RyanMogul6800 dude not only do I want to say thanks for the settings thread, but your ROMs are awesome. Quick question to anyone who might be able to answer it, this is the first time I get a mogul not to work on mms, i tried all settings, and read through a lot of threads and still no dice, is it possible that the settings might need to be refreshed on the cricket network side? internet and sms work flawlessly, just MMS does not work, it stays stuck at downloading 0%. Thanks in advance!
EDIT: Ok I have ryans heavy rom, and it may seem weird but I installed his mms wap fix from his sig and now it works flawlessly!
Glad you like, but MMS works on MY ROM without that CAB
My ROM works flawless without using the MMS fix CAB from my Shared Site. That CAB is for users not using my ROM or that have messed up their settings on their own.
Now assuming you already have PST set correct and that you are Using MY Cricket ROM.
First thing you do after MY ROM is booted up and running is MAKE SURE ITS UNPLUGGED and WI-FI is OFF! I hate when people leave the phone Cradled for all of their Flashing and Programming. It needs wi-fi off and needs to be unplugged to set up WAP. You need WAP (DATA) set up for MMS to work. So you want to make sure you have unlimited DATA plan with Cricket.
Now after the Phone with MY ROM is unplugged and wi-fi is off simply open up Internet Explorer and Navigate to a real webpage(yahoo.etc) and then enter the info and password click save. Done.
There are some cases after setting up with Cricket needing to call them again and have the account refreshed on their end. There are other instances where Crickets end takes a long time to refresh automatically on their own.
I really believe you ran into a Cricket account refreshing delay problem. Installing the Arcsoft MMS fix cab had nothing to do with why your MMS works now. Do not try uninstalling that CAB to prove me wrong as it will mess up the ROMs settings and will require you to hard reset.
What you could do if you really want to know for sure, is hard reset then let the ROM boot and set up the Internet with phone unplugged. After that I am willing to bet that you can send and receive MMS without installing the CAB we are referencing.
I am glad you like the settings and the ROM.
are you working on a WM 6.5 rom for cricket?
Thanks,
Scott
Some one PLEASE help i have tried to run several prl's including the 1007 i think it was anyhow (the latest 3g prl..) only 1x works for my raphael on cricket ...im getting frustrated... thanks
Wait... Cricket has 3G EVDO? No way... only seen there stuff work at 1x.
jnellz said:
Some one PLEASE help i have tried to run several prl's including the 1007 i think it was anyhow (the latest 3g prl..) only 1x works for my raphael on cricket ...im getting frustrated... thanks
Click to expand...
Click to collapse
You will only get 1x on a CDMA phone flashed to Cricket. They use a different band for their 3G that is not supported by Sprint / Verizon Phones .. It's a Cricket Thing.
THANKS SO MUCH thats what i figgured i just needed a second opinion DAMN! HTC FUZE
Here i come
Uh well, not true. Def not true. Im new to this flashing stuff, only on my second day. I purchased my vogue already flashed to cricket but it was VERY GENERIC. No touchflo, nothin, just windows 6.0 nothin else. It was getting evdo signals at that time, but i needed to reset some registry settings, which i did and was getting evdo signals with working internet and mms....THROUGH EVDO......NO BS THIS WAS JUST a day or 2 ago. But, problem was, i put touchflo on it, and didnt realize that the previous owner had somehow filled up the memory on the phone with applications and files that were nowhere to be found. It was crawling...So my solution.....? I decided to re-flash it myself because i knew that would delete all the useless stuff on the phone that i had no use for. I flashed the stock sprint rom from the htc website to get the most current radio, then unlocked the phone, then re-programmed it. When i got the phone it already had the 1050.prl file on it, which is an EVDO PRL!!! Go to corolada.com and look at the left side of the page and there is a list of EVDO AND NON EVDO CRICKET PRL's 1050 being the most universally recognized. Fast forward to now, I have finally found a rom that is fast and clean that i plan on keeping. Well now theres a whole nother problem. My phone is no longer recieving EVDO signals. BUT CRICKET HAS WORKING EVDO I KNOW FOR A FACT I have had so many cricket phones that connected to pic messaging and internet through evdo. Im sorry if i misunderstood your post and you were just saying that a flashed phone from sprint cant get evdo, but either way, i know for a fact that a flashed sprint phone is fully capable of sending and recieving cricket evdo signals because i was surfing the net on my vogue through cricket evdo just a day or two ago. Can anyone figure this out??? IVE tried reloading the prl. ive tried different prl's. ive even tried puttin the original sprint prl on the phone and then changing it back to the 1050 cricket prl, and to no avail, no evdo signals. someone please help, im pulling my hair out. why couldnt i just leave the phone alone when it had evdo? why did i have to go and try to make it pretty?????
sound like it's not authenticating ##DEBUG# ,debug info,"HDR" it should be 1=Athenticated
if not, ##778# , M.I.P Default profile, Delete AAA & HA shared secret & resest
jtmfnslim said:
sound like it's not authenticating ##DEBUG# ,debug info,"HDR" it should be 1=Athenticated
if not, ##778# , M.I.P Default profile, Delete AAA & HA shared secret & resest
Click to expand...
Click to collapse
HERES SOMETHING I GOT FROM "HOFO" that might help out some of u cricket people with PST setting issues/ hope this helps a lil:
==========================================================
CRICKET PST Settings Thread! by Ryan Mogul
This is for people who want Cricket to work perfectly, just follow these instructions not skipping a beat and you will be OK from then on! If you are not having problems obviously skip this!
This thread is assuming that you already have your phone Unlocked(spc code all zeros) It is also assuming that you already have a CRICKET PRL file loaded in PST. If you have my ROM flashed than PRL's are on device memory we will get to that below.
1. Now first thing you want to do is have a good Cricket ROM installed like "clears throat* Mine lol.
2. Now if you are starting from a fresh flash OK, if you are starting from a Hard reset OK, we can continue. If you have a ROM installed that is having problems I recommend a hard reset and skip customizations using stylus when it says you have 3 seconds.
3. Now open your Phone Application and go to options and make sure smart dial is off. Then dial ##778 call button, now click edit and enter six zeros. Now click view info and goto PRL, now check to make sure you have a CRICKET PRL(1013,1014,1050 etc.. there are others)If you dont have one loaded and you are using my ROM then you can click update and it should goto main root, pick prl 1050. Let it do its thing and restart. If you already have a CRICKET PRL then skip the update step.
4. Now cancel out of EPST if you didnt update PRL. (for both people who had to restart and people who didnt) <--open phone application again and dial *228(this will make sure base settings are good so i will not have to explain as much, it will also download a local EVDO prl to where you are), it will dial cricket and do its programming thing. Do not interupt this. Let it do its thing even if it restarts. Now when you are back in action we can continue.
5. Open phone application and dial ##778 call button, now click edit and enter six zeros. In main page the only two things we are going to do is change the NAM name to Cricket, and check the MSID number make sure its a 10 digit number thats in your area code BUT it IS NOT your PHONE NUMBER!! If its fine we can continue, if not you may of skipped the *228 step so you need to do that or you need to obtain this from calling Cricket.
6. Now click view info and goto AKEY and make sure its blank, nothing there. Now click view info and goto NAM settings, NAM name should be Cricket, Mobile Directory number should be YourTenDigitPhoneNumber, MIN1 should be that other phone number the (MSID) that is not your phone number! but it should be 7 digits, ex: sevendigitnumber, MIN2 should be just your area code. MSID should be 10digitMSIDnumber <--again not yourphonenumber!, MCC should be 310, MNC should be 00, NMSI should be your MSID(XX10digitnumber<--not your phone number) THE XX'S should be zeros, ex: 007185548692, Now if all these settings in this paragraph didnt need touched assuming you didnt skip any of my steps(which they shouldnt be touched i am just making sure) we can move on.
7. Click view info and goto CDMA settings, we are going to make sure they are set right and change a couple things for Clearer voice transmissions, people will compliment how good your phone sounds even in some cases. EVRC should be set at Disable, Home page should be Voice 13k, the Two below it the Same Voice 13k.
8. Click view info click modem settings, change slot cycle index to 1, This will make the phone ring a little sooner, also get your texts a bit sooner. The other 4 options should be Auto, Auto, Enable, No in Order from top to bottom.
9. Click View Info and pick Security, now we are changing this regardless you must do this, we are going to Unauthenticate you and Re-authenticate, it is a Needed step everything in this How To needs to be done and Not skipped! Change the HDR Auth User ID to something bogus like [email protected], the passord below it make it something random but remember it, now do the same for PPP user ID and password but make them the same as the HDR ones.
10. Click view info and pick MIP Settings, Make sure Active Profile is on 0, MIP mode should be Simple IP only, MIP reg retries should be 1, MIP reg retry timeout should be 2000 ms, MIP pre-reg timeout should be 30, Mobile Node HA auth should be Disable, send a reg request should be Enable, dormant handoff to disable.
11. Click view info and pick MIP Default Profile, Enable profile should be enable, NAI should be [email protected], MN HA SPI set should be enable, MN HA SPI value should be 12c, MN AAA should be enable, MN AAA SPI value should be 2, reverse tunneling should be enable, home address should be 0.0.0.0, Primary HA address should be 68.28.15.12, secondary should be 68.28.31.12, HA shared secret and AAA secret should be cricket <--lowercase, DMU public should be 0, MN Authenticator should be 0.
12. Click view info and pick MIP customer profile 1 and make sure its Profile enabled is disabled. Now do the same with the other 4 below it.
13. Ok now click menu, ok and let it reset, but make sure not to do anything we are going to be going right back INTO EPST, so when it boots back up open the Phone application and dial ##778, we are going to re-authenticate you its easy, now click edit and enter six zeros, click view info and goto Security, now change the HDR AN Auth to yourtendigi[email protected], password should be cricket<--lower case, same for PPP user id and Password make them same as HDR.
14. Click view info and goto MIP default profile, make sure the HA, and AAA shared secrets are both cricket<---lowercase, then click menu OK and let it reset.
Thats it! PST settings are perfect for CRICKET, you have a Local EVDO prl file installed, and you are Authenticated for Data and EVDO, now if you used my ROM just go to internet explorer and goto a real page, and follow instructions but remember to click save password!
Thats done, every flash from now on should never affect your PST settings and you should always be authenticated. I hope this helps everyone.
Cricket 3g network
I just got off the phone with cricket customer service. I wanted to upgrade to there 3g network. The representative said,"the 3g is reserved for original cricket phones.
it doesnt matter if you put a 3g prl on the cdma raphael because it is a dual band phone and crickets 3g network only works on their new triband phones so your still stuck with 1x and evdo
So here is my story, about 3 weeks ago I bought a touch pro off of ebay, that was for "pageplus"... well it turns out it was actually a sprint phone that had been flashed to pageplus. It worked for voice and text, but no data. The seller gave me a partial refund, and I figured I could get it to work. Anyway 3 weeks later I have it unlocked with Mightyrom 6 running and everything is great, except for some intermittent keyboard issues. I figure why not a hard reboot, see if its something that I had installed.Thats where everything when down hill. When It finished booting, it had jumped carriers to Verizon. If i tried to call with it all I got was verizons customer service. I've spent the last 6 hours trying to get this thing to work. My on going struggle can be read over at Howardsforum
http://www.howardforums.com/showthread.php?t=1638018
I've learned a lot, and in that way its been great, but at the end of the day I would prefer a working phone. I posted over here hoping that someone would have some advice.
I've decided to post all the settings from EPST in hopes that someone can set me strait
I will be using 1234567890 to represent my phone number, as I dont need any crank calls : )
I changed my MSL to 000000 with QPST
I am currently running MightyROM 6
My phone is a HTC Touch PRo
Display
NAM name SPCs
SCM 58
ESN (hex) *******
ESN (dec) *********
MSID 1234567890 (MY NUMBER)
Life Counter 2051
Life Timer 111hrs,24mins,35Sec
Life data RX 1184180957
Life Data TX 81933745
Software Version Mighty Rom
Firmware Version 1.03.03v
Hardware Version 0002
PRI version 1.47_003
PRU Checksum 5E2FFAF3
Refurbish status YES
Refurbish Date 31-Jul-2009
Manufacture Date 12-Feb-2009
Warranty Data code <NO Data>
A-Key
Authentication Key *blank*
Nam Settings
NAM Name SPCs
Mobile Directory Number 1234567890 (MY NUMBER)
MIN1 4567890
MIN2 123
MSID 1234567890 (MY NUMBER)
MCC 310
MNC 00
NMSI 001234567890
IMSI 310001234567890
True MIN1 4567890
True MIN2 123
True MSID 1234567890 (MY NUMBER)
True MCC 310
True MNC 00
True NMSI 001234567890
True IMSI 310001234567890
ACCOLC 7
CDMA Settings
A-sys Primary 283
B-sys Primary 384
A-sys Secondary 691
B-sys Secondary 777
MOB_TERM_FOR_HOME ENABLE
MOB_TERM_FOR_SID ENABLE
mOB_TERM_FOR_NID ENABLE
EVRC ENABLE
Home Page EVRC
Home Orig EVRC
Roam Orig Voice 13k
Home SID/Home NID
Home SID/NID #1 30/65535
Home SID/NID #(2-20) 0/0
Modem Settings
SLot Cycle Index 2
Preferred Serving Sys. Automatic
Preferred Mode Automatic
HDR Hybrid Preferred Enable
Clear all MRU entry No
PRL
Update PRL File
PRL ID 51807
PRL Capability (prl typ) IS-683C
PRL Capability (prefer only) Disable
PRL Capability (default roaming indicator) 68
Data Parameters
Packet Dial String #777
Rev. A Enable
Phone Directory
Emergency #1 911
Emergency #2 *911
Emergency #3 #911
*(all else blank)*
M.I.P Settings
Number of Profiles 6
Active user profile index 0
MIP MODE Mobile IP Preferred
MIP Registration Retries 2
MIP Registration Retry Timeouts 1750 ms
MIP Pre-Registration Imeout 0
Mobile Node-HA Authentication Enable
Send a Registration Request only in Use Disable
Dromant Handoff Optimization Enable
M.I.P. Default Profile
Enable Profile Enable
NAI [email protected]
MN HA SPI Set Enable
MN HA SPI Value (hex) 12C
MN AAA SPI Set Enable
MN AAA SPI Value (hex) 2
Reverse Tunneling Preferred Enable
Home address 0.0.0.0
Primary HA Address 255.255.255.255
Secondary HA Address 255.255.255.255
DMU public key (PKOID) 10
M.I.P Custom Profiles (all of them are the same)
Enable Profile Enable
NAI
MN HA SPI Set Enable
MN HA SPI Value (hex) 4D2
MN AAA SPI Set Enable
MN AAA SPI Value (hex) 4D2
Reverse Tunneling Preferred Enable
Home address 0.0.0.0
Primary HA Address 0.0.0.0
Secondary HA Address 0.0.0.0
DMU public key (PKOID) 0
There is always the possibility that I miss spelled something, If anyone sees any mistakes please let me know!!!
Joined: Apr 2010
Posts: 11
wahahahahhaha, she's alive, SHE IS ALIVE ... my phone finally works again, that was a rough 24 hours... the thing that I entered wrong was the MSID... who knew that phones had two phone numbers. Thanks to Ebay seller Kittywireless for their help. They didn't make a dime from me, and helped me find the answer.... One bonus of all this BS is it forced me to learn a lot of stuff about my phone, and now the Data is working
I have the same problem!!!
Could you happen to do me a huge favor. Im using a samsung rant from sprint and everything that happend to you happend to me!!! could you type out the data settings for you phone ie: User NAI, SPI MN-HA, SPI MN-AAA, Rev Tun Pref, Home Address, Primary HA-IP, Second HA-IP and your browser gateway ( you can get there by pressing ##3282#) thank you sososososo much!!!
can someonne please send me the updated profile file of point me in the correct direction because in stuck. i rooted my evo 3d form hboot 1.5 to 1.4. everything works fine but my internet connection is constantly at 1x. my baseband is 1.06.00.1216 and my prl has been updated manually (by zip) to 21081. ive tryed virtually everything and im stuck. i have tryed to do settings / update / profile... that gives me an error 67. ive tryes to do ##72786# to reset the phone. it takes activation just fine and hangs on the updates and throws error 67. for the evo 4g's i remember the profile being a part of the flashable radio zip. im asking for someont to help me out and send me the profile or point me in the right direction...
currently on the mean rom 3.92, ive used mikrunny and mr esp stock shooter rom... with the same results... thanks in advance.
Call sprint, I had the same thing happen, they might be changing your towers as well, if they say that so and so towers have tickets, ask what for. The tech on the end, not a customer rep, said they were making huge updates. I'm now getting 4mbs+ on 3g half bars. The tower can take up to 72 hours.
Sent from my PG86100 using xda premium
Btw, might want to move this to Q&A.
Sent from my PG86100 using xda premium
^^^ Tandem #FAIL!!!!!
veladem said:
Call sprint, I had the same thing happen, they might be changing your towers as well, if they say that so and so towers have tickets, ask what for. The tech on the end, not a customer rep, said they were making huge updates. I'm now getting 4mbs+ on 3g half bars. The tower can take up to 72 hours.
Sent from my PG86100 using xda premium
Click to expand...
Click to collapse
called them, did nothing... anyone got the profile please?
By did nothing do you mean they didn't fix your problem...
Our did nothing as in no towers are down in your area, I had 1x and 25Kbs for a while.
Sent from my PG86100 using xda premium
^^ if you dont know dont comment!!! smh
veladem said:
By did nothing do you mean they didn't fix your problem...
Our did nothing as in no towers are down in your area, I had 1x and 25Kbs for a while.
Sent from my PG86100 using xda premium
Click to expand...
Click to collapse
thats correct, no towers are down. the phone worked fine before the downgrade other people with tsimilar phones are fine..
Get your MSL. (MSL Reader on Market)
Go into Dialer, dial ##3282#
Press Edit, Enter your MSL.
Press EVDO, change Preferred Mode to Automatic.
Press Menu, and Commit Modifications.
Unknownforce said:
Get your MSL. (MSL Reader on Market)
Go into Dialer, dial ##3282#
Press Edit, Enter your MSL.
Press EVDO, change Preferred Mode to Automatic.
Press Menu, and Commit Modifications.
Click to expand...
Click to collapse
EVDO preferred mode is automatic and DDTM is disabled.. i didnt have to change anything
jdmegkoupe said:
EVDO preferred mode is automatic and DDTM is disabled.. i didnt have to change anything
Click to expand...
Click to collapse
Change it to CDMA Only then, and commit, then reboot, and change it back to automatic and commit and reboot again.
It seems as though your NAI/HA pass or AAA pass from your profile 0 is incorrect. That's why you r getting that error 67 message when trying to update profile. You might want to RTM (Reset To Manufacturer) the phone. You r going to need your MSL/SPC in order to perform this. You start by going to the phone dialer and hitting ##786#, this will open up the "Reverse Logic Support" menu. In here you will see your MDN, MSID, MAC-ID, etc... Once here, press the Menu button and hit "Reset". It will then ask for the MSL/SPC, enter your MSL and hit OK.
NOTE: Before attempting this BACK UP, BACK UP, BACK UP EVERYTHING YOU DON'T WANT TO LOOSE. This function will reset your phone back to manufacturer settings, meaning it will wipe everything and revert it back to stock settings.
Hope this helps. Cheers!
M3_Arsenal said:
It seems as though your NAI/HA pass or AAA pass from your profile 0 is incorrect. That's why you r getting that error 67 message when trying to update profile. You might want to RTM (Reset To Manufacturer) the phone. You r going to need your MSL/SPC in order to perform this. You start by going to the phone dialer and hitting ##786#, this will open up the "Reverse Logic Support" menu. In here you will see your MDN, MSID, MAC-ID, etc... Once here, press the Menu button and hit "Reset". It will then ask for the MSL/SPC, enter your MSL and hit OK.
NOTE: Before attempting this BACK UP, BACK UP, BACK UP EVERYTHING YOU DON'T WANT TO LOOSE. This function will reset your phone back to manufacturer settings, meaning it will wipe everything and revert it back to stock settings.
Hope this helps. Cheers!
Click to expand...
Click to collapse
i think i tryed this when i called sprint...im at work right now but ill try it on break and let you guys know whats going on...thanks for all your help
no deal, im going to use qxsp or whatever to go into profile 0 and zero some stuff out and see it itll reset itself with a handset reset
i see the problem in my profile 0 theres a ton of gibberish in my nai field its (ff000) and it goes on for a while. research says that the nai is supposed to be my imei so im guessing its corrupted... ill keep you guys posted on the repair because im not even going to touch that subject... unless anyone who knows how can let me know ! i have active user set to 0 and the damn thing keeps giving me write errors!!! im using QPST
jdmegkoupe said:
i think i tryed this when i called sprint...im at work right now but ill try it on break and let you guys know whats going on...thanks for all your help
no deal, im going to use qxsp or whatever to go into profile 0 and zero some stuff out and see it itll reset itself with a handset reset
Click to expand...
Click to collapse
That is really strange... The result you had with the RTM suggest 1 or 2 things. Your phone was partially flashed or fully flashed to different carrier that required to repair the MEID. The other possibility is that your phones Profiles were modified and eventually were corrupted or lost. Be careful using QPST, you may end up causing more damage. After the phone OTA's, profile 1 is automatically populated. Usually looking like this...
Rrofile 1: Enabled
NAI: <first/lastname>@sprintpcs.com
MN HA SPI Set: Enable
MN HA SPI Value(Hex): 4D2
MN AAA SPI Set: Enable
MN AAA SPI Value(Hex): 4D2
Reverse Tunneling Preference: Enable
Home Address: 0.0.0.0
Primary HA Address: 255.255.255.255
Secondary HA Address: 68.28.89.76
DMU Public Key: 0
HA Shared Password: secret
AAA Shared Password: 6 character password provided by Sprint via the OTA
Hope this gives u an idea of what goes where. Good luck and let us know how it works out. Cheers!
---------- Post added at 09:25 PM ---------- Previous post was at 09:18 PM ----------
jdmegkoupe said:
i see the problem in my profile 0 theres a ton of gibberish in my nai field its (ff000) and it goes on for a while. research says that the nai is supposed to be my imei so im guessing its corrupted... ill keep you guys posted on the repair because im not even going to touch that subject... unless anyone who knows how can let me know ! i have active user set to 0 and the damn thing keeps giving me write errors!!! im using QPST
Click to expand...
Click to collapse
Profile 0 is bit more complicated to populate. Normal settings are somewhat like this...
Profile: Enable
NAI: <MEID HEX>@hcm.sprintpcs.com
MN HA SPI Set: Enable
MN HA SPI Value(Hex): 4D2
MN AAA SPI Set: Enable
MN AAA SPI Value(Hex): 4D2
Reverse Tunneling Preference: Enable
Home Address: 0.0.0.0
Primary HA Address: 68.28.15.12
Secondary HA Address: 68.28.31.12
DMU Public Key: 0
HA Shared Password: secret
AAA Shared Password: (this is normally written in HEX format and its 32 string character)
This is obtained by an algorithm which computes your "MEID HEX, HEX DEC" among other things. Sorry can't help beyond this point.
M3_Arsenal you know your stuff dude!!! thanks for all your help!! i got it working 4g also.
That is really strange... The result you had with the RTM suggest 1 or 2 things. Your phone was partially flashed or fully flashed to different carrier that required to repair the MEID. The other possibility is that your phones Profiles were modified and eventually were corrupted or lost. Be careful using QPST, you may end up causing more damage. After the phone OTA's, profile 1 is automatically populated. Usually looking like this...i did the hboot downgrade its possible i pulled the plug late or something... idk... just glad its FIXED!!!!!!!
jdmegkoupe,
Im glad to see that your phone is up and running again. Cheers.