hi people this is my ever first post i think. Just wanna ask if i got the correct settings that i extracted from an original V3m Alltel. I worked on my Sprint mogul and changed it to Alltel ppc6800 rom. Now i changed all the settings so it would finally work on alltel network. Pls advice me if made a mistake on the setting, much appreciated.
Display NAM NAME GNPO
Home SID/ Home NID Home SID/ Home NID #1 0/65535
Home SID/ Home NID #1 0/65535
PRL PRL ID 30029
Security HDR AN AUTH User Id(long) %[email protected]
HDR AN AUTH Password(long) %E
PPP USER ID [email protected]
PPP PASSWORD alltel
M.IP SETTINGS Number of Profiles 5
Active User Profile Index 1
MIP_MODE Simple IP Only
MIP Registration Retries 1
MIP Registration Retry timeout 2000ms
MIP Pre-registration timeout 30
Mobile Node-HA Authentication Disable
Send a Registration Request Enable
Dormat Handoff Optimization Disable
M.IP Default Profile Enable Profile Enable
NAI [email protected]
MN HA SPI set Enable
MN HA SPI value (hex) 101
MN AAA SPI Set Enable
MN AAA SPI Value (hex) 3E2
Reverse Tunneling Preffered Enable
Home Address 0.0.0.0
Primary HA Address 0.0.0.0
Secondary HA Address 0.0.0.0
HA Shared secret secret
Public Key 0
MN Authenticator(Hex) 800100
M.IP profile 1 Enable Profile Enable
NAI [email protected]
MN HA SPI set Enable
MN HA SPI value (hex) 101
MN AAA SPI Set Enable
MN AAA SPI Value (hex) 3E2
Reverse Tunneling Preffered Enable
Home Address 0.0.0.0
Primary HA Address 0.0.0.0
Secondary HA Address 0.0.0.0
HA Shared secret secret
Public Key 0
MN Authenticator(Hex) 800100
M.IP profile 2 - 5 Enable Profile Enable
NAI
MN HA SPI set Enable
MN HA SPI value (hex) 0
MN AAA SPI Set Enable
MN AAA SPI Value (hex) 0
Reverse Tunneling Preffered Disable
Home Address 0.0.0.0
Primary HA Address 0.0.0.0
Secondary HA Address 0.0.0.0
HA Shared secret secret
Public Key 0
MN Authenticator(Hex) 800100
I just re-ROM'd my phone and now it looks like
my data plan isn't working.
I have a sprint 6850 hacked to VZW
The ROM I used was SROSLER's ROM.
I KNOW it resets the EPST settings, and I did get it back on the
Verizon network.
So it's not the ROM's fault.
But it now says "Cannot connect for unknown reason" when I try
to call for data.
When I dial *22899 all the phone does is beep twice and the call ends.
It doesn't look like it's writing the HA and AAA shared secret.
My Mip settings are:
Enable Profile: Enable
NAI: (my10digitphonenumber)@vzw3g.com
DUN NAI: (my10digitphonenumber)@dun.vzw3g.com
MN HA SPI Set: Enable
MN HA SPO Value (Hex):12C
MN AAA SPI Set: Enable
MN AAA SPI Value (Hex):0
Reverse Tunneling: Enable
Home Address 0.0.0.0
Primary HA: 255.255.255.255
Secondary HA: 255.255.255.255
HA Shared Secret:
AAA Shared Secret:
DMU public key(PKOID):10
MN Authenticator (Hex):0
Ideas?
Some one PLEASE help i have tried to run several prl's including the 1007 i think it was anyhow (the latest 3g prl..) only 1x works for my raphael on cricket ...im getting frustrated... thanks
Wait... Cricket has 3G EVDO? No way... only seen there stuff work at 1x.
jnellz said:
Some one PLEASE help i have tried to run several prl's including the 1007 i think it was anyhow (the latest 3g prl..) only 1x works for my raphael on cricket ...im getting frustrated... thanks
Click to expand...
Click to collapse
You will only get 1x on a CDMA phone flashed to Cricket. They use a different band for their 3G that is not supported by Sprint / Verizon Phones .. It's a Cricket Thing.
THANKS SO MUCH thats what i figgured i just needed a second opinion DAMN! HTC FUZE
Here i come
Uh well, not true. Def not true. Im new to this flashing stuff, only on my second day. I purchased my vogue already flashed to cricket but it was VERY GENERIC. No touchflo, nothin, just windows 6.0 nothin else. It was getting evdo signals at that time, but i needed to reset some registry settings, which i did and was getting evdo signals with working internet and mms....THROUGH EVDO......NO BS THIS WAS JUST a day or 2 ago. But, problem was, i put touchflo on it, and didnt realize that the previous owner had somehow filled up the memory on the phone with applications and files that were nowhere to be found. It was crawling...So my solution.....? I decided to re-flash it myself because i knew that would delete all the useless stuff on the phone that i had no use for. I flashed the stock sprint rom from the htc website to get the most current radio, then unlocked the phone, then re-programmed it. When i got the phone it already had the 1050.prl file on it, which is an EVDO PRL!!! Go to corolada.com and look at the left side of the page and there is a list of EVDO AND NON EVDO CRICKET PRL's 1050 being the most universally recognized. Fast forward to now, I have finally found a rom that is fast and clean that i plan on keeping. Well now theres a whole nother problem. My phone is no longer recieving EVDO signals. BUT CRICKET HAS WORKING EVDO I KNOW FOR A FACT I have had so many cricket phones that connected to pic messaging and internet through evdo. Im sorry if i misunderstood your post and you were just saying that a flashed phone from sprint cant get evdo, but either way, i know for a fact that a flashed sprint phone is fully capable of sending and recieving cricket evdo signals because i was surfing the net on my vogue through cricket evdo just a day or two ago. Can anyone figure this out??? IVE tried reloading the prl. ive tried different prl's. ive even tried puttin the original sprint prl on the phone and then changing it back to the 1050 cricket prl, and to no avail, no evdo signals. someone please help, im pulling my hair out. why couldnt i just leave the phone alone when it had evdo? why did i have to go and try to make it pretty?????
sound like it's not authenticating ##DEBUG# ,debug info,"HDR" it should be 1=Athenticated
if not, ##778# , M.I.P Default profile, Delete AAA & HA shared secret & resest
jtmfnslim said:
sound like it's not authenticating ##DEBUG# ,debug info,"HDR" it should be 1=Athenticated
if not, ##778# , M.I.P Default profile, Delete AAA & HA shared secret & resest
Click to expand...
Click to collapse
HERES SOMETHING I GOT FROM "HOFO" that might help out some of u cricket people with PST setting issues/ hope this helps a lil:
==========================================================
CRICKET PST Settings Thread! by Ryan Mogul
This is for people who want Cricket to work perfectly, just follow these instructions not skipping a beat and you will be OK from then on! If you are not having problems obviously skip this!
This thread is assuming that you already have your phone Unlocked(spc code all zeros) It is also assuming that you already have a CRICKET PRL file loaded in PST. If you have my ROM flashed than PRL's are on device memory we will get to that below.
1. Now first thing you want to do is have a good Cricket ROM installed like "clears throat* Mine lol.
2. Now if you are starting from a fresh flash OK, if you are starting from a Hard reset OK, we can continue. If you have a ROM installed that is having problems I recommend a hard reset and skip customizations using stylus when it says you have 3 seconds.
3. Now open your Phone Application and go to options and make sure smart dial is off. Then dial ##778 call button, now click edit and enter six zeros. Now click view info and goto PRL, now check to make sure you have a CRICKET PRL(1013,1014,1050 etc.. there are others)If you dont have one loaded and you are using my ROM then you can click update and it should goto main root, pick prl 1050. Let it do its thing and restart. If you already have a CRICKET PRL then skip the update step.
4. Now cancel out of EPST if you didnt update PRL. (for both people who had to restart and people who didnt) <--open phone application again and dial *228(this will make sure base settings are good so i will not have to explain as much, it will also download a local EVDO prl to where you are), it will dial cricket and do its programming thing. Do not interupt this. Let it do its thing even if it restarts. Now when you are back in action we can continue.
5. Open phone application and dial ##778 call button, now click edit and enter six zeros. In main page the only two things we are going to do is change the NAM name to Cricket, and check the MSID number make sure its a 10 digit number thats in your area code BUT it IS NOT your PHONE NUMBER!! If its fine we can continue, if not you may of skipped the *228 step so you need to do that or you need to obtain this from calling Cricket.
6. Now click view info and goto AKEY and make sure its blank, nothing there. Now click view info and goto NAM settings, NAM name should be Cricket, Mobile Directory number should be YourTenDigitPhoneNumber, MIN1 should be that other phone number the (MSID) that is not your phone number! but it should be 7 digits, ex: sevendigitnumber, MIN2 should be just your area code. MSID should be 10digitMSIDnumber <--again not yourphonenumber!, MCC should be 310, MNC should be 00, NMSI should be your MSID(XX10digitnumber<--not your phone number) THE XX'S should be zeros, ex: 007185548692, Now if all these settings in this paragraph didnt need touched assuming you didnt skip any of my steps(which they shouldnt be touched i am just making sure) we can move on.
7. Click view info and goto CDMA settings, we are going to make sure they are set right and change a couple things for Clearer voice transmissions, people will compliment how good your phone sounds even in some cases. EVRC should be set at Disable, Home page should be Voice 13k, the Two below it the Same Voice 13k.
8. Click view info click modem settings, change slot cycle index to 1, This will make the phone ring a little sooner, also get your texts a bit sooner. The other 4 options should be Auto, Auto, Enable, No in Order from top to bottom.
9. Click View Info and pick Security, now we are changing this regardless you must do this, we are going to Unauthenticate you and Re-authenticate, it is a Needed step everything in this How To needs to be done and Not skipped! Change the HDR Auth User ID to something bogus like [email protected], the passord below it make it something random but remember it, now do the same for PPP user ID and password but make them the same as the HDR ones.
10. Click view info and pick MIP Settings, Make sure Active Profile is on 0, MIP mode should be Simple IP only, MIP reg retries should be 1, MIP reg retry timeout should be 2000 ms, MIP pre-reg timeout should be 30, Mobile Node HA auth should be Disable, send a reg request should be Enable, dormant handoff to disable.
11. Click view info and pick MIP Default Profile, Enable profile should be enable, NAI should be [email protected], MN HA SPI set should be enable, MN HA SPI value should be 12c, MN AAA should be enable, MN AAA SPI value should be 2, reverse tunneling should be enable, home address should be 0.0.0.0, Primary HA address should be 68.28.15.12, secondary should be 68.28.31.12, HA shared secret and AAA secret should be cricket <--lowercase, DMU public should be 0, MN Authenticator should be 0.
12. Click view info and pick MIP customer profile 1 and make sure its Profile enabled is disabled. Now do the same with the other 4 below it.
13. Ok now click menu, ok and let it reset, but make sure not to do anything we are going to be going right back INTO EPST, so when it boots back up open the Phone application and dial ##778, we are going to re-authenticate you its easy, now click edit and enter six zeros, click view info and goto Security, now change the HDR AN Auth to yourtendigi[email protected], password should be cricket<--lower case, same for PPP user id and Password make them same as HDR.
14. Click view info and goto MIP default profile, make sure the HA, and AAA shared secrets are both cricket<---lowercase, then click menu OK and let it reset.
Thats it! PST settings are perfect for CRICKET, you have a Local EVDO prl file installed, and you are Authenticated for Data and EVDO, now if you used my ROM just go to internet explorer and goto a real page, and follow instructions but remember to click save password!
Thats done, every flash from now on should never affect your PST settings and you should always be authenticated. I hope this helps everyone.
Cricket 3g network
I just got off the phone with cricket customer service. I wanted to upgrade to there 3g network. The representative said,"the 3g is reserved for original cricket phones.
it doesnt matter if you put a 3g prl on the cdma raphael because it is a dual band phone and crickets 3g network only works on their new triband phones so your still stuck with 1x and evdo
I'm looking for EPST Settings for my Touch Pro to work in Sacramento area of california. So far, this is what I've got from Metro. They gave me a NAM Number which is 916-308-0677. MDN: 916######(My phone number) and home sid/nid 6503. They gave me another service programming number which is 587846 but I don't know where this goes.
the Phone has already been flashed to MetroPCS and when I dial 611 it takes me to metropcs. But when I call somebody, it says,"Welcome to American Roaming Network." So I'm assuming there's some settings that are incorrect. If you got a touch pro working on metro, please post some settings here. It would make a great tutorial as well.
Just put ##778# in dialer and view epst settings under "Display, NAM Settings, CDMA Settings, Home SID/Home NID, Modem Settings, PRL, Security, Data Parameters, Phone Directory, M.IP Settings, and M.IP Default Profile"
Please kindly post your settings here. It'll make a good tutorial and help alot of people. Thanks in advance.
the following are needed.
From "Display"
NAM Name
SCM
MSID
From "NAM Settings"
NAM Name
Mobile Directory Number
MIN1
Min2
MSID
MCC(Mobile County Code)
MNC(Mobile Network Code)
NMSI
IMSI
From "CDMA Settings"
A-Sys Primary
B-Sys Primary
A-Sys Secondary
B-Sys Secondary
MOB_TERM_FOR_HOME
MOB_TERM_FOR_SID
MOD_TERM_FOR_NID
EVRC Enabled
Home Page
Home Orig
Roam Orig
form "Home SID/Home NID"
Home SID/NID #1
from "Modem Settings"
Slot Cycle Index
Preferred Serving System
Preferred Mode
HDR Hybrid Preferred
Clear All MRU entry
from "Security"
HDR AN AUTH User ID
HDR AN AUTH Password
PPP USER ID
PPP PASSWORD
from "Data Parameters"
Packet Dial String
from M.IP Settings
Number of Profiles
Active User Profile Index
MIP_MODE
MIP Registration Retries
MIP Registration Retry
MIP Pre-Registration
Mobile Node-HA Auther
Send a Registration
Dormant Handoff
From "M.IP Default Profile"
Enable Profile
NAI
MN HA SPI Set
MN HA SPI Value
MN AAA SPI set
MN AAA SPI Value
Reverse Tunneling
Home Address
Primary HA Address
Secondary HA Address
HA Share Secret
AAA Shared Secret
DMU Public Key
MN Authenticator
Yes, it's a quiet a bit of work, but it'll create a perfect Guide for many people. So, someone please be brave and come forward and put some effort in to help complete this guide. Majority of these settings are available here on a very good thread but some key critical settings are not well defined. So, if anyone wanna take a shot at it, please come forward. Any help will be greatly appreciated. Thanks .
Many many thanks to the person who created this thread and posted those settings. I actually worked on my touch pro using those settings. Now, a final touch is needed.
http://forum.xda-developers.com/showthread.php?t=571190
There is a knowledgeable person in Sac named Kareem that flashes HTC phones over to metro...http://sacramento.craigslist.org/mob/1532028309.html he might be able to help...
He flashed several phones for me...
he wouldn't reply
I contacted him a few times but wouldn't reply. Also, he charges a lot. Its like 120 bucks he charges to program it. I can't afford that. I've already have it flashed and most settings in, but dunno if he will lemme know of that last ones. But again, I doubt he will help regarding this matter.
you need to get your MSID
So I almost have this done, but I've got a problem. I can get 3G, but not phone or text. When I call, I'm sent to the American Roaming Network, and when I once got an error about International Data Roaming, I saw Verizon Mobile in the paragraph right before I hit the No button. I've tried out a ton of PRLs, but none get me the phone. I KNOW it's not a typo somewhere. My MIN is correct everywhere. Everyone uses my Google Voice number, and I'm using GooVe IP so I can (usually) get calls, but it's not even close to being the same. Here's what I've done so far...
changed my ESN/MEID on my Cricket account
CDMA Workshop v2.7.0
..successfully sent 000000 SPC
..wrote NVRAM file I got from whiterabbit.org
..wrote PRL 45722 (My Ascend was 45626, but I can't get my hands on that particular PRL, so I've tried several others)
..reset
QPST 2.7 Build 366
..CDMA tab
....changed Directory # and IMSI_S to mynumber
..Roam tab
....changed NAM 1 Directory # to mynumber
....set Preferred Roaming to 45722 PRL
..M.IP tab
....set Active User to 0
....set Mobile IP Behavior to Mob + Simp f/back
....edit User Profile
......set NAI and Tethered NAI to mynumberatmycricketdotcom
......HA and AAA Shared Secrets, checked Enter text string, entered cricket for both
......checked Rev Tunnel Preferred
......entered all zeros in the Home, Primary HA, Secondary HA addresses
..PPP Config tab
....Um
......entered User ID: mynumberatmycricketdotcom, checked Req PW enc, entered cricket
......checked Optimized Domant Handoff and 1xEVDO->1x
....AN
......entered User ID: mynumberatmycricketdotcom, checked Req PW enc, entered cricket
..wrote to phone
created APN shortcut with anycut, went in and entered this...
Name - Cricket
APN - internet
Proxy - wapdotmycricketdotcom:8080
Port 8080
Username - mynumberatmycricketdotcom
Password - cricket
Server - wapdotmycricketdotcom
MMSC - httpcolon//mmsdotmycricketdotcom/servlets/mms
MMS Port - 8080
MCC - 310
MNC - 004
Authentication type - PAP or CHAP
APN type - <Not set>
Any ideas?
(I'm too newb to post outside links, so I had to italicize stuff.)
edit: If it's a PRL issue, I'm Leesburg, VA
First idea is to not be cheap and get the network the phone is ment for.
Sent from my DROID X2 using xda premium
ferg40 said:
First idea is to not be cheap and get the network the phone is ment for.
Sent from my DROID X2 using xda premium
Click to expand...
Click to collapse
Thanks for the advice, but I'll wait for someone who knows proper English.
So I guess my main problem was I was using my phone number for my MIN and my MDN, though on my old phone these were different numbers. Also, this is a dual band phone, and Cricket in my area is triband. I'm probably going to have to find another route altogether.