I flashed many times my Nike using using sspl-1.16-nike.exe.
But more than a year, I installed Nike 1.22 shipped Hardspl and from then I used Official Rom's.
And now I have a question. I have to do this again (even with 1.22):
1. download the attached files
2. REMOVE SIM and SD CARDS !!
3. connect usb cable
4. copy sspl-1.16-nike.exe to your device and run it (usb cable must be connected!)
5. after a few seconds "USB" appears on the display
If yes, what should I use instead sspl-1.16?
Tiago Machado said:
I flashed many times my Nike using using sspl-1.16-nike.exe.
But more than a year, I installed Nike 1.22 shipped Hardspl and from then I used Official Rom's.
And now I have a question. I have to do this again (even with 1.22):
1. download the attached files
2. REMOVE SIM and SD CARDS !!
3. connect usb cable
4. copy sspl-1.16-nike.exe to your device and run it (usb cable must be connected!)
5. after a few seconds "USB" appears on the display
If yes, what should I use instead sspl-1.16?
Click to expand...
Click to collapse
No, you don't have to do it again.
Regards
Related
Well I was trying to upgrade mt niki to 6.1 but apparently I must have missed a step or did something I shouldt have and now I am stuck with the color bar screen. Can anything be done? I am running Vista.
tri-colour = Bootloader
The tri colour screen is the boot loader screen, when you updated, did the progress bar go allll the way to 100%?
If so, its in bootloader, try to flash another rom from you computer,
Also run through what you done to update - What rom also. Did you hard-spl, Uspl or anything like that?
It stopped at 15%. These are the directions I was following:
Originally Posted by Judge584
Follow these steps:
1. download the attached files (flash-uspl-niki.zip & sspl-1.16-nike)
2. REMOVE SIM and SD CARDS !!
3. connect usb cable
4. copy sspl-1.16-nike.exe to your device and run it (usb cable must be connected!)
5. after a few seconds "USB" appears on the display
6. unplug and replug the usb cable
8. you can now flash the uspl by running ROMUpdateUtility.exe from flash-uspl-niki
9. Now you can flash the latest rom update to have spl 1.22 and wm6.1.
ouch, Thats the only problem with sspl,
urmm.
How long did it stay at 15%?
As the device isn't CID unlocked you can only flash official roms...
Find an official rom, in the bootloader connect the USB and see if it will flash. It should do!
fingers crossed..
the only rom I can find for singtel in singapore is an updated one so I am trying that now so far so good, I am at 30%. So if this will get me going again can you offer a little advice or explination as to your last post, how do I go about loading a newer 6.1 rom on my device?
Of course, thats what these forums are for. The singapore rom shouldn't hassle you tooo much if you know your way around Windows mob well enough. Let me know how it goes and i'll help you through..
Deejaynate said:
Of course, thats what these forums are for. The singapore rom shouldn't hassle you tooo much if you know your way around Windows mob well enough. Let me know how it goes and i'll help you through..
Click to expand...
Click to collapse
well i was able to fix it by using the singtel rom. I want to use the Niki SuperCID unlocker but I have to install the " HardSPL 1.15 MFG " first - can you walk mw through this so I dont brick my touch again. do you have messenger?
yeah Windows live messenger, add me [email protected]
sorry to hijack your thread, but I encountered exactly the same thing. The screen is now stuck with 3 colour bands. I tried to flash it with an official rom, but the computer is not connecting with the phone, active sync does not recognise the device, any help!?
this is what I did:
1. download the attached files
2. REMOVE SIM and SD CARDS !!
3. connect usb cable
4. copy sspl-1.16-nike.exe to your device and run it (usb cable must be connected!)
5. after a few seconds "USB" appears on the display
6. unplug and replug the usb cable
8. running ROMUpdateUtility.exe from flash-uspl-niki
Sorry for the non prompt reply
I have been at work alot lately,
sorry for a non prompt reply.
Active sync wont connect to your phone, as its in bootloader mode.
At the tri-colour screen, does you computer beep when you connect it, or try to install drivers?
thanks for replying!
no beep from the computer, when connecting the usb to the phone, the phone changes from "serial" to "usb".
I tried reflashing with ROMUpdateUtility.exe from flash-uspl-niki, it will work, but says fail and will go into recovery mode. It will then complete the "recovery" action and go back to flashing new rom which won't work.......
The same ocurred with me!! Help me!
In the middle of an unlocking process, somehow(in the flashing radio process,i got 100%, and then a message saying: an writing error ocurred). So my htc dual got with the image NIKI200 (and four colour - red,green,blue and white..). Now i tried hard reset and after i presse send to initialize, the phone goes to that bloody image....i cant do nothing....what should i do? help me please....regards
luismatos123 said:
In the middle of an unlocking process, somehow(in the flashing radio process,i got 100%, and then a message saying: an writing error ocurred). So my htc dual got with the image NIKI200 (and four colour - red,green,blue and white..). Now i tried hard reset and after i presse send to initialize, the phone goes to that bloody image....i cant do nothing....what should i do? help me please....regards
Click to expand...
Click to collapse
You need to flash an original ROM from your service provider (phone company).
hey guys plzzzzzzzzzzzzzz help me with this i`m in deep
i have WM6.5
my radio version is 1.65.28.25
i have no sound at all but i can make a phone call the front speaker works (the one u put overur ear when u make a call) but the back one doesnt work at all !
no 2nd camera
when i open the slide the screen starts to respond wierldy :S
i tried to follow this
1. download the attached files
2. REMOVE SIM and SD CARDS !!
3. connect usb cable
4. copy sspl-1.16-nike.exe to your device and run it (usb cable must be connected!) (run it where plzz? using the phone file exploerer or dirctly from the pc)
5. after a few seconds "USB" appears on the display(is it the one with the tri clolr mood?)
6. unplug and replug the usb cable (when i do it nothing happens :S it stucks at the tri color mood)
(OPTIONAL, better to skip it! step 7. if you only want to test the sspl try flashing the attached splash screen by running ROMUpdateUtility.exe from flash-splash-niki)
8. you can now flash the hardspl-1.15mfg-nike.nbh by running ROMUpdateUtility.exe from flash-uspl-niki( i have done it without doing the sspl 1.16 and it worked :S is that correct to do???)
9. after installing the hardspl you can flash any rom (rom cook project
[Q] Do I need "Active Sync" to use CustomRUU, or can it just be in the Tri-Color Boot Loader manager with the USB cable connected?
I assume you can flash without being in WM, if so, my WM install can stay very thin for android porting.
11011011
If you are going to flash by connecting to your computer via usb cable, and you are using a WinXP computer, you will need to flash via ActiveSync.
If a Vista or Win7 computer, you need the latest version of Windows Mobile Device Center installed and connected.
No, your phone does not need to be booted into WinMo to flash, you can also connect to your computer with your phone in bootloader, and then running the customruu,
(power the phone on while pressing volume down button, will see tri-color screen) but booting WinMo fully and connecting via ActiveSync or WMDC is recommended.
Or as an alternative, you can put your ROM on a small (I prefer 4gb class 2) sd card (not in any folder, just on the root of the card-preferably an empty card) and turn the phone on with the card in it the same way as if you were going into bootloader, and the phone should tell you what to do from there. (Just the ROM goes on the card, not the customruu.exe , only the file LEOIMG.nbh)
Just make sure you have HSPL installed, and make double sure you have a compatible ROM
Hi!
I've a HTC 7 Mozart that after bad unlock, shows "Enter USB Host Mode.." in the screen. It doesn't have SD Slot, so I can't put a goldcard for repairing it. It's from Orange Spain, and there aren't any roms yet. How can I recover it?
Best Regards,
NeTRaW said:
Hi!
I've a HTC 7 Mozart that after bad unlock, shows "Enter USB Host Mode.." in the screen. It doesn't have SD Slot, so I can't put a goldcard for repairing it. It's from Orange Spain, and there aren't any roms yet. How can I recover it?
Best Regards,
Click to expand...
Click to collapse
what are you trying to unlock, have you tried the master reset, whiles the phone is off, hold volume up/down then press the power and a menu should show up for master reset.
hi This problem can be solved only by the xtc clip
zozo -->> http://www.youtube.com/watch?v=QaYXxXgqDtU
Solution with Gold Card and Y Cabel.
NeTRaW said:
Hi!
I've a HTC 7 Mozart that after bad unlock, shows "Enter USB Host Mode.." in the screen. It doesn't have SD Slot, so I can't put a goldcard for repairing it. It's from Orange Spain, and there aren't any roms yet. How can I recover it?
Best Regards,
Click to expand...
Click to collapse
Hi Brother,
Here is solution.
Windows Phone 7 handsets stuck in USB Host Mode
This looks like it's common to all WP7 phones, not just the Mozart but it's particularly annoying here because you need to feed the Sim Card/Flex adapter under the battery, over the battery retaining clip and under the battery cover. Very fiddly. Very easy to accidentally press the power button.
IF YOU PRESS THE POWER BUTTON INSTEAD OF VOL DOWN + CAMERA YOU WILL SOFT BRICK THE PHONE. IT WILL BE STUCK IN USB HOST MODE.
Fortunately to fix the phone you just need the "special cable" with MicroSD reader from the WP7 upgrade kit, the Gold Card you make in step A and the firmware for the phone you're working on.
1.Take the firmware .exe and extract the largest file (Ruu_signed.nbh or something similar)
2.Rename it using the same 4 letter naming convention that the DIAG file already on the goldcard with a IMG suffix e.g. MOZAIMG.nbh
3.Copy it to the MicroSD. You can use the XTC Clip as a card reader. This is the slowest part of the procedure.
4.Delete the DIAG file
5.Put the MicroSD card in the "special cable" and plug it into the phone without pressing any particular buttons. This will automatically reflash the phone with the possible bonus of debranding the phone.
6.Once the phone has booted up, you can proceed with trying to unlock it again.
Hope this helps.
Same problem encountered on the HD7: http://forums.phone-tools.cn/showthr...-mode-solution
Similar walkthrough for debranding: http://forum.xda-developers.com/showthread.php?t=892657
If its help you then thanks to orginal Master.
Thanks
Br, Raja
NeTRaW said:
Hi!
I've a HTC 7 Mozart that after bad unlock, shows "Enter USB Host Mode.." in the screen. It doesn't have SD Slot, so I can't put a goldcard for repairing it. It's from Orange Spain, and there aren't any roms yet. How can I recover it?
Best Regards,
Click to expand...
Click to collapse
Dear Members...
After a long time i got solution for this problem. Yesterday i resolved one mozart which shows Enter USB Host Mode without using Y-Cable procedure.
This may work on many mozart, which has this problem with bootloader 5.12.2250 & dont have rom for their region. U can try this, before using Y-Cable procedure.
The solution is...
1. Download "WP7_Update_Cab_Sender.zip", from this forum & extract it.
2. Press Camera button & Power On the mozart. Dont release Camera button until the mozart shows computer connectivity symbol in the
display. Then release pressing the camera button & connect the moazrt to pc.
3. Now goto the extracted folder to this "WP7_Update_Cab_Sender\tools\x86" folder via MS-DOS prompt or copy cmd.exe to this folder and
open it. So that u will get, direct location of that path in command prompt.
4. In Command Prompt type "UpdateWP.exe /list". This shows the connected devices details in the screen.
5. Then type"UpdateWP.exe /reset". This will try to reset the mozart & restarts it to normal condition. Wait for few minutes
(not more than 5-10 mins) to get in to normal stage.
That's all...
If the solution doesn't work you, then dont blame me... & you can try with Y-Cable procedure...
It works dude thanks i shoud search for commands for ms dos
USB Host Mode
Was trying the same thing but no luck.
After several months, I realized my notebook's USB ports aren't that good anymore.
What I did is connect it to another PC (Win7 Home Premium) and download Zune (I installed other dependencies first like Windows Mobile Drivers for Vista). Get another cable if you have to. I connected it to the PC using a 3-headed USB cable (not a Y-cable since I don't have it).
Wait for several minutes, and the phone just shut itself off and on again with the HTC logo.
Instead of going to the USB mode, it goes to the....well, setup page after you factory reset it.
That's how I fixed my paperweight just today.
Must be Santa giving an early present.
+ Que PPC said:
It works dude thanks i shoud search for commands for ms dos
Click to expand...
Click to collapse
Sent from my SM-N900T using XDA Premium HD app
Hey guys, as the title suggests....im having trouble
Trying to update my ROM.
Active sync works fine, up to the point I have to run the RUU and .nbh files, it just drops out and then i get the error 266 coming up.....asking me to check the cable etc.
Tried different USB ports and leads with no joy.
Strange one this, as I have updated my ROM before (around a year ago) with no trouble.
Help very much appreciated.
marlon32, ActiveSync has nothing to do with flashing process,
Enter bootloader mode (switch off, press & hold Volume down, switch on), than connect to the USB cable.
The word Serial on tricolor screen will be changed for USB.
Now start RomUpdateUtility....
AndrewSh said:
marlon32, ActiveSync has nothing to do with flashing process,
Enter bootloader mode (switch off, press & hold Volume down, switch on), than connect to the USB cable.
The word Serial on tricolor screen will be changed for USB.
Now start RomUpdateUtility....
Click to expand...
Click to collapse
I have also tried this method, but the nothing happens.
When in bootloader mode and the USB cable connected, it is not able to recognise what Image is already on my phone. Even if i click next it fails again with the error 266 msg.
I thought I understood that active sync had to be established first?
Im following these instructions:
FIRST TIME FLASH
1. Remove SD (and remove Application Data and Program Files folders from it using SD card reader)
2. Remove HSPL with HSPL2_RUN.exe (flash SPL 1.66.0000 with HSPL2_RUN.exe)
3. PowerOff the phone
4. Boot to bootloader (VolDown+PowerOn) and when it shows "USB" flash stock ROM by running matching RUU_Leo_S_HTC_XXX_3.14.XXX_Radio_15.42.50.11U_2.15 .50.14_LEO_S_Ship.exe (get yours HERE or for Orange UK/FR HERE)
5. Hard Reset (when phone starts booting after step 4, remove the battery, insert it back press VolUp+VolDown and still holding both press PowerOn and follow the instructions)
6. Boot to homescreen.
7. Run SSPL_RUU.exe with Artemis v4X RUU_Signed_XXXX.nbh in the same folder - YOU HAVE TO BE ON HOME SCREEN, NOT BOOTLOADER (this took me 3 tries until succeded - yes - nerve wrecking, but works). If it doesn't work (hangs on black screen for more than 2min or stays at 0%) remove the battery and try again. If still doesn't work - try solutions in NOTE below.
8. Hard reset (instructions in step 5)
9. when on homescreen - softreset.
10. Insert SD
marlon32 said:
I have also tried this method, but the nothing happens.
When in bootloader mode and the USB cable connected, it is not able to recognise what Image is already on my phone. Even if i click next it fails again with the error 266 msg.
I thought I understood that active sync had to be established first
Click to expand...
Click to collapse
You're going about things in a strange manner, using hspl.exe to set a stock spl and then using sspl to flash the rom? Pretty non standard, what are you aiming for? My guess is you are using outdated instructions from before Hspl4 was released to handle spl/hspl 3.03 (just a guess, of course)
Stabdard flashing a 3.14 rom would go as follows,
Phone into bootloader(forget actuvesync)
Run Hspl4.exe, choose 3.03.hspl
Back into bootloader,
Run the Artemis flash using custom ruu .
Done.
It won't show the current installed image because that is a simple registry entry and is only accessible when winmo is running, but when winmo is running the USB times out when the ruu reboots into bootloader,sim that's why we manually enter bootloader.
(I haven't checked in the Artemis thread as to if there's a reason why his rom wouldn't follow standard proceedures, but I did use exactly your process prior to Hspl4 release)
Thanks for the reply.
What the issue seemed to be (after reading other threads) is that mu laptop is USB 3 and no HTC programme does not like it!
When i used an older laptop everything was fine flashing HSPL 3.03.
Out of interest is it true that USB 3 does not programme correctly?
marlon32 said:
Thanks for the reply.
What the issue seemed to be (after reading other threads) is that mu laptop is USB 3 and no HTC programme does not like it!
When i used an older laptop everything was fine flashing HSPL 3.03.
Out of interest is it true that USB 3 does not programme correctly?
Click to expand...
Click to collapse
Thanks M8 Had the same problem and moved my usb cable to another port worked 100%