Related
After I tried to downgrade my Qtec2020 from WM2005 tot WM2003SE the updated stoped in stage 1.
This is what I found in the RUULog.log file:
19:15:11 Connection with Serial
19:16:31 Begin stage 1
19:17:01 CE Erase retry 1
19:17:31 CE Erase retry 2
19:18:01 CE Erase retry 3
Now I am stucked in bootloader mode and tried softreset, hardreset, special WM2005 hardreset but nothing seems to work. I have only a grey screen with Serial v1.02 on it.
Is there anybody who could help me
I've never performed any downgrades from WM5.0 but I have an idea that could work?
Install WM5.0 again, then perform a Hardreset but this time perform the Registry and Storage format (press power+record+camera+reset pin for about 5 seconds and you should see a menu on the screen, by using the record button to select an option and camera button to change to YES. It should be NO, YES, YES and press ACTION button to save changes). Then unhide the Extended ROM and erase anything in there.
Then perform the downgrade to WM2003SE.
I hope this works for you...
Regards,
Rayan
Thanks for the information but it's not the solution.
I tried to install WM5 again but I get an error 112 during the install.
The RUULog.log file:
20:42:03 Connection with Serial
20:43:26 Begin stage 1
20:43:56 CE Erase retry 1
20:44:26 CE Erase retry 2
20:44:56 CE Erase retry 3
The device is still stuck in bootloader mode. All the reset actions won't work (soft, hard, special)
Have you tried the upgrade/downgrade method using an SD card instead of the cradle/pc?
No I only tried it by USB/PC. I will search the forum for how to do this and give it a try. I will let you know later if this is the solution. Thanks for the information so far.
Regards Marco
I search the forum but can't find any way to do this. Can someone tell me how to flash by SD card
It's in the Wiki, not the forums...
Here you go:
http://wiki.xda-developers.com/index.php?pagename=XDAtools
Good Luck!
Hi, I was just upgading my XDA 2 os when my laptop froze in the middle of the upgrade! Now it only has the o2 startup screeen it won' turn off or connect to my computer to complete the upgrade. What can I do?
Is my Xda gone for good??
skud try aggain
you can put it back in bootloader mode and try aggain
this time on a destop you know power problem in laptop
you will not want a power failure in the middle of an upgrade
hope thats helped
Stuck on Bootloader
I experienced the same thing too.
Just detached battery from your device for about 10 minutes (I pressumed, may need more time)... then do the downgrade again.
in your PC task manager ''end process'' the ff:
''wcescomm.exe''
''WCESMgr.exe''
''rapimgr.exe''
now connect again the device and start the reflash...it works for me.
hope this wl help you...
No joy I'm afraid. How can I get it back in bootloader mode when I can't get past the O2 startup screen. Putting in an sd card Doesn't do anything either it is completely dead except for the annoiying but colorful O2 Logo.
Ok, it just turned itself off so I am after turning it back on andnow all I have is a white screen! What is going on? The laptop crashed when it was at 65% in the upgrade proces.
I'll give this taskmanager thing a go and get back to ya.
Thanks for all the help btw!
I have placed a ROM.nb1 on my SD card, but I get a eror with the XDA OS Image Tool. It looks that I can't find any way to get out of the bootloader mode whatever reset I tried. The battery was out for almost 12 hours but this also makes no difference. Is there a other way to flash by SD card or is there a way to reset/upgrade the bootloader mode. I think the bootloader mode hangs or is corrupt.
Regards Marco
I've tried that now and it still won't connect and still the same white screen! Any othere suggestions? Is there anything I can download which would force a connection or install something onto my XDA or does anyone know how I can get past this blank screen and maybe get to the settings window?
This must have happened other people anyone managed to fix this?
:!: :!:
hey power kite! It seems we got similar problems but your a bit ahead in getting it fixed. Can you tell me where you got the Rom.nb1 file so I can give this XDA tool thing a go?
What kinda power kite you got BTW?
Here is the link where I get the NB1 file
http://forum.xda-developers.com/viewtopic.php?t=8606&highlight=sd+rom
Good luck
Cheers Power kite,
I was just doing a bit of seaching on the sd flash method and found a website that takes you throught it step by step if your interested
http://en.pdamobiz.com/en/forum/PDAforum_posts.asp?TID=93&PN=1
Hurray I'm back in business!!! Talk about relief! :lol: Its upgrading as we speak!
Now just to watch it like a hawk and not let this crappy laptop crash again!
Thanks everyone!
Give that link a look Power kite.
Skud
99% !!!!!!!
Great that it worked for you.
I did procedure 1, 2 and 3 but I'm still stuck in bootloader mode. Every upgrade WM2005, WM2003SE wich I have flashed before give me an error 112. I have flashed my SD card but I don't get any instructions on my screen.
Is it possible to install the bootloader again or upgrade it. I think my problem is the bootloader.
got stuck on o2 splash screen. don't know what happend and what to do.
got any tips?????
thanks
Do a hard reset -> press the power button and the reset button at the same time
i've done it already and still hangs...
Reflash the rom with one from your original operator. If you're using an o2 xda please download a rom from www.my-xda.com and follow the on screen instructions.
well my friend i think somehow ur OS is lost and all u still have is the extended rom OS image,that's why u still see the splash screen...
i assume that ur device is a himalaya(though u did'nt mention any informations :wink: ),but if really is,then do the following:
1-log in to this forum as user:xda pass:xda
2-go to ftp server from the wiki page(up left ur screen)
3-go to himalaya folder and download any rom u would like 2 have(it can appear in several way,exe file or several files zipped in a .zip)
4-if it's and exe file and u have winrar,then extract the content in a folder,u will find 6 files(maybe less,rarely 1 file more-xda2nbftool.exe-),now forget about this file for the moment
u will need 2 file to fix ur phone:nk.nbf & HimauUpgradeUt.exe(i idvice u to dowload an O2 rom upgrade to prevent country id error wich can be fixed if necessary )
now that u have the tools,do the following:
1-press power button+navigation pad(the round one between the green and the red buttons)+reset button SIMULTANESLY,u will enter bootloader mode(blank screen with serial on the upper side of the screen,number like 1.06 on the buttom)
2-put the cradle in usb port DIRECTLY IN UR COMPUTER NOT THROUGH USB HUB
3-put ur phone in the cradle while it's in bootloader mode,u will see that the serial word in the upper screen have changed into USB
4-run HimaUpgradeUt.exe and follow the on screen instructions,u will see a status bar,wait untill it finishes,hard reset ur phone,and here we go
i forgot to mension that u should put those 2 files(HimaUpgradeUt.exe & nk.nbf),in a separate folder,close any open task on ur desktop/laptop,and PUT UR CHARGER IN THE CRADLE for the battery don't run out...
hope i helped
tell me what happened with u dude,and remember that ur in the best PDAs developping site in the world,so don't worry,hopefully,everything can be fixed....
RAGO :lol:
sorry, forgot to mention, yes its himalaya.
ok, i will try all your advices
thanks a lot
rago,
thanks for the tips, it worked.
ur always welcome bro
good to know that u have ur device back
RAGo, I did the same, and it said MODEL ID ERROR. How to fix that? Mine is now WM2005.
hi prd00...
replace the HimaUpgradeUt.exe in ur upgrade folder with the attached file,u will bypass country ID error...
good luck
RAGO :lol:
Hi all,
I think I need help from you guys. I have my xdaII dead with screen showing bootloader(it turns to USB when i plug into usb port). after I followed the instructions above...it shows model ID error. Please help....
problem solved
sorry guys...i forgot to use the given attachment file...thanks a lot.
Special thanks to RAGOv. your tips is worked.
splash
good day.
i have similar problem. it occured after installing items from an extended rom (specifically ARABIZER). i tried installing other items in the same extrom, and it just worked fine.
what can be the solution? i was hoping i can install teh ARABIZER.
thank you.
splash
good day.
i have similar problem. i am using i-mate ph10b (himalaya). it occured after installing items from an extended rom (specifically ARABIZER). i tried installing other items in the same extrom, and it just worked fine.
what can be the solution? i was hoping i can install the ARABIZER.
thank you.
dead XDAIIS (in bootloader mode) please help..
Dear Guys,
My XDAIIs is in bootloader mode (it shows serial--> at top and V 2.07--> at bottom, and doesnt turn to usb when i plug into my usb port). Does anyone know how to fix it? Please help....
hi ordinary...
haven't u said it worked!!!so what happened next???!!
plz explain more,for the mean while try changing the USB port ur using,check ur cable,and try to change the computer(desktop/laptop)...
if it doesn't work plz explain more what happened,so we can help u find the solution...
@arcquisumbing:u are not clear in ur post my friend...what same problem(are u in bootloader mode???!!),how did it happened after installing item from the extended rom????and u want a solution for what???!!!
sorry i couldn't help u my friend but plz try to explain more so we can undestand ur problem...
RAGO :lol:
stuck in splashscreen
i'm sorry.
i was referring to the stuck in splash screen.
after the hard reset, autorun was initiating installations for the contents of the extrom. i installed each and every item and at the end of it, it required resetting. i just clicked on yes to reset, then when it did, it just stops at the splash screen. i tried waiting for an hour or so, maybe it would just come, but still to no avail. i tried re-installing everything, but still the same thing. but when i tried NOT TO INCLUDE the ARABIZER, everything worked just fine.
now, i'll just pray for two things, 1-that you can help me solve this problem, and 2-that the light at the end of the tunnel is not a train.
thanks. more power to you.
hi arcquisumbing
now if u still have a 2003 OS on ur device,wich i doubt it,(i've read ur post in the thread How can I increase Storage memory in WM 2005),then ur problem can be solved inchallah :wink:
*if ur device is i-mate,do the following:
1-remove arabizer from Ext ROM,so ur device can enter OS
2-install arabizer cabs after being in the OS
download arabizer cabs from here http://forum.xda-developers.com/download.php?id=6292
*if ur device is not an i-mate,then u have to wait untill my no brand arabizer succeeds.... :wink:
RAGO :lol:
Re: splash
arcquisumbing said:
good day.
i have similar problem. i am using i-mate ph10b (himalaya). it occured after installing items from an extended rom (specifically ARABIZER). i tried installing other items in the same extrom, and it just worked fine.
what can be the solution? i was hoping i can install the ARABIZER.
thank you.
Click to expand...
Click to collapse
Hey bro since you have an Imate! Download this file from clubimate http://www.clubimate.com/support/PPC/ROM/RUU172810WWE_CDL_SKU2.exe and flash it.
I'm sure your problem will be solved for sure
Ps : RUU172810WWE_CDL_SKU2.exe is just the Arabic Extended Rom
dead XDAII and XDAIIs
Hi RAGOv,
THank you for your willingness to help my problem
1. The one I said worked is for my xdaII, but only to pass the MODEL ID error (it runs well, after i use your attachment file. I upgrade it to O2 ROM upgrade 1.66 WWE). However, After finish upgrading, It still stuck on O2 splash screen.
2. Now, Im facing the other thing. "the dead XDAIIs". Its screen only appear O2 splash screen when i put on the battery(even i already did a hard reset). Then I tried to change mode into bootloader mode (by pressing power button, record, and reset).in the end, after I did an upgrading. it also stucks on O2 splash screen.
Please help...I dunno what to do anymore..
My dopod is on ipl/spl 2.20
while trying to update to the latest PV 4.0.0.0.6 Touch, i encountered an error..
Fine, reset the device, went to bootloader, started the PV_Temp upgrade file for my G3 dopod.
halfway, the update fails and says the NBF file cannot be used.
i've tried every other NVID rom and it is the same..
so now i'm stuck in the bootloader screeen and i can't do anything
Please try the search button in this forum!!! And don't worry it's not bricked;-)
sayjeng said:
My dopod is on ipl/spl 2.20
while trying to update to the latest PV 4.0.0.0.6 Touch, i encountered an error..
Fine, reset the device, went to bootloader, started the PV_Temp upgrade file for my G3 dopod.
halfway, the update fails and says the NBF file cannot be used.
i've tried every other NVID rom and it is the same..
so now i'm stuck in the bootloader screeen and i can't do anything
Click to expand...
Click to collapse
check your .NET Framework and see if you have the 2.0 version installed. Reboot your pc and start again. We always experience these hiccoughs.
i've tried the search..
seriously saying, its quite hard to find what i want..
i seem to be able to flash the PV_TEMP ROM, it says on my computer its successful but my PDA just goes back to bootloader.
anyway, i'm installing .Net framework 2.0... will see how that goes..
still doesn't work..
RUU says its congratulations...
PDA goes back to bootloader
i cna flash jester's rom, i can flash PV_temps rom..
but all i get is the bootloader screen after that..
can't flash the NVID thats from the upgrade guide... it just says wrong NBF file..
wonder how much will it cost for me to send it to service center to replace the whole flash chip
new problem, now i can't do anything at all cause i think my batt is dead..
how can i recharge it ?
sayjeng said:
new problem, now i can't do anything at all cause i think my batt is dead..
how can i recharge it ?
Click to expand...
Click to collapse
so you know now what is the problem!
recharge it by connecting to a PC with USB and wait wait wait and hope for the best. Try recharging it by what ever means you can do. If you said, you are successful in getting PVtemp, then, try installing battery_status.cab (find it search it by google or whatever) and watch the battery_status line on the front page and wait for a + sign before the 100mA at the right bottom line to appear.
Wait till it is full, then redo step 2 again. I'm sure you can get over without getting the machine to the manufacturer for repair.
no no
the first problem still stands
i'm still stuck at bootloader..
but now i can't flash anything cause my batt is dead..
so i've got 2 problems now
hello all,
sayjeng, I got the same problem last week.
I couldn't use any RUU rom because of the corrupted nbf file.
The PV_TEMP rom worked but I was stuck on boot loader screen too...
I tried many times and with some random hard resets... Eventually, the fourth time , WM5 started...
My advice are :
- charge your battery by any means like SeaPea said
- reboot your desktop computer
- remove your (fully charged) battery from your phone for some seconds and put it back...
Really, I may have been lucky that time...
I just wanted to post here to say that I sympathize...
Good luck!
will give it a try tomorrow..
its past 1am now and i need to be up early tomorrow..
if it doesn't, really have to make a trip to service center..
wonder what should i tell them then..
oh, forgot to mention
i can't hard reset..
i can get to the part where it says 'Press Send to restore factory default, Other keys to quit'
when i press Send, it says Format FAT Partition and followed by Format is Failed
then i get a flash for 1 sec of the vendor boot screen which is all green, and its back to bootloader
sayjeng said:
oh, forgot to mention
i can't hard reset..
i can get to the part where it says 'Press Send to restore factory default, Other keys to quit'
when i press Send, it says Format FAT Partition and followed by Format is Failed
then i get a flash for 1 sec of the vendor boot screen which is all green, and its back to bootloader
Click to expand...
Click to collapse
me too....any progress?
Jow ... flash your rom from dopod!
If your Radio Rom is crashed ... it stuck at Bootscreen too! After that it must run! it fix partition errors too.
ROm from dopod is 2.15..
my prophet is now on 2.20...
i can't flash it... i haven't been able to find a vendor rom wiht 2.20..
does anyone have any ? Qtek maybe ?
something to get my prophet running...
cause i did try in my attempt to get my prophet back by flashing the Radio ROM.. and it fails.. maybe thats why i can't boot my prophet
tried almost every rom..
used almost every RUU
anyone got any RUU that might help ?
or any suggestions ? thinking of throwing the towel and just pass it to dopod for them to handle....
worst case, change ROM chip
finally
I got this to work using the guide - BUT:
Windows XP SP2 English was the key for me.
I used VMWare to do step 1 of flashing (NVID)
then step 2 of flashing I did on a separate PC.
Worked after so many different attempts
i am running on XP sp2 english.. not using vista..
problem is, i can't even hard reset my phone.. it just says Format is Failed.
but my phone seems fine and still responds to my plugging the USB in and reseting....
Hi sayjeng
The same problem with my imate jamin too..
Whatever you said in you posts is an exact recall of my case.
Now it makes two of us
Waiting to see if someone can come up with a solution.
IPL/SPL at 2.20
Frequent automatic disconnection from activesync.
No means to charge the battery which i think is almost dead.
Tried the Dopod rom,for no avail.
The list goes on and on just like yours.
help..Anyone..?
I get all the way to the progress bar and them it just stays there for a very long time and nothing happen? Help is greatly appricated.
Ok beings as you've told us nothing in your post .
1. Are you using a 100% genuine Topaz (Diamond 2)?
2. Which ROM are you trying to flash ?
3. is the progress bar on the white flash screen or on the first boot windows screen?
4. Have you used Hard_spl?
5. Are you using a guide to flash your phone or just going hit & miss styls?
6. Are you flashing from the memory card or from the computer?
Add those to your next post and maybe we'll be able to help you
I'm using a HTC Pure from At&t, I'm trying to use Hard_spl, goes into bootloader mode and I get a progress bar with 0% and stays there, Hard_spl guide, from the computer. total noob!
acseazzu said:
I'm using a HTC Pure from At&t, I'm trying to use Hard_spl, goes into bootloader mode and I get a progress bar with 0% and stays there, Hard_spl guide, from the computer. total noob!
Click to expand...
Click to collapse
1) what does the phone screen show for version number before the progress bar comes up?
2) if you let the whole thing go on, do you get an "error 262" at the end on the PC? or another error?
cmonex said:
1) what does the phone screen show for version number before the progress bar comes up?
2) if you let the whole thing go on, do you get an "error 262" at the end on the PC? or another error?
Click to expand...
Click to collapse
1) "TOPA210 32M
SPL-1.83.0000
MicroP-Topaz (LED) v11
TURBO HW/TURBO SW
TP MFG DATA
512,547 190,885
193,205 829,206
826,886 Calibrated
2)Yes I eventually get the 262 error.
I went to the HTC site and ran their stock HTC pure image and it worked just fine.
acseazzu said:
1) "TOPA210 32M
SPL-1.83.0000
MicroP-Topaz (LED) v11
TURBO HW/TURBO SW
TP MFG DATA
512,547 190,885
193,205 829,206
826,886 Calibrated
2)Yes I eventually get the 262 error.
I went to the HTC site and ran their stock HTC pure image and it worked just fine.
Click to expand...
Click to collapse
Ok that should be the correct version for Hard_spl but for the sake of it go into tri-colour mode (details in the Hard spl thread) and check it says olinex in that mode. If it does some people have reported that doing this works.
1. Reflash to stock ROM ( i know you have already done this and can skip this step but it's there for future use)
2. Run the Hard_spl relocker file found in the hard spl thread http://forum.xda-developers.com/showthread.php?t=520312
3. Start the phone make sure the stock ROM still works ok.
4. Reflash Hard_spl newest version again found in this post http://forum.xda-developers.com/showthread.php?t=520312 follow instructions in that thread.
5. Once you have the Hard_spl installed on your device (again it's in that first post how to check)
6. Pick your new ROM from the ROM's section on this forum.
7. Download and flash using this guide http://forum.xda-developers.com/showthread.php?t=585201 (Please note it's easier and technically safer to flash using a memory card if you have one as this minimizes - if not removes - the chance of getting a connection error)
If it doesn't say Olinex then you haven't flashed hard_spl successfully follow the thread listed above to flash it on then your ROM
warlordxxx said:
Ok that should be the correct version for Hard_spl but for the sake of it go into tri-colour mode (details in the Hard spl thread) and check it says olinex in that mode. If it does some people have reported that doing this works.
1. Reflash to stock ROM ( i know you have already done this and can skip this step but it's there for future use)
2. Run the Hard_spl relocker file found in the hard spl thread http://forum.xda-developers.com/showthread.php?t=520312
Click to expand...
Click to collapse
I keep on getting Error 262 again.
acseazzu said:
I keep on getting Error 262 again.
Click to expand...
Click to collapse
At which point while you are trying to flash hard spl ?
acseazzu said:
1) "TOPA210 32M
SPL-1.83.0000
MicroP-Topaz (LED) v11
TURBO HW/TURBO SW
TP MFG DATA
512,547 190,885
193,205 829,206
826,886 Calibrated
2)Yes I eventually get the 262 error.
I went to the HTC site and ran their stock HTC pure image and it worked just fine.
Click to expand...
Click to collapse
nooo, do not put it in bootloader manually by pressing buttons!
run Automatic mode in Hard-SPL, and tell me what the phone screen shows before flashing.
I have exactly the same problem with one of my Topaz, have two, the other one did not have any problem? Stays at 0% and then error.
walsco said:
I have exactly the same problem with one of my Topaz, have two, the other one did not have any problem? Stays at 0% and then error.
Click to expand...
Click to collapse
are you using automatic mode?
I've tried both modes, in automatic it say that I can't use it profesionally, I guess it complains because I already flashed the other one? But then again I can't even run the TopazSPLRelocker_SPL133, it to stays at 0% and then error, feels like the phone would have a dip switch that sayn, no flashing, but then again, stock rom just works fine everytime.
BTW my phone have these data:
Topa100 32M
SPL-2.51.0000
MicroP-Topaz (LED) v10
TURBO HW/TURBO SW
Cool, everything is turbo, hw and sw, hahahahahahaha
walsco said:
I've tried both modes, in automatic it say that I can't use it profesionally, I guess it complains because I already flashed the other one? But then again I can't even run the TopazSPLRelocker_SPL133, it to stays at 0% and then error, feels like the phone would have a dip switch that sayn, no flashing, but then again, stock rom just works fine everytime.
Click to expand...
Click to collapse
you can send us a message for help here : http://support.htc-unlocks.com/
hi guyz..
im in deep trouble. i've a htc hd2 with android installed on it. i tried to restore its original windows OS. i followed a thread and downloaded leoimg.nbh and tried to installed. now im getting this error and phone get stuck after that "Upgrade Rom code error please try again.".
i tried every solution avaliable on the forums but couldn't find any luck.
another problem is when i try to download ROM from htc.com it asks for serial number and when i enter serial number mentioned at the back of the phone "S/N:SH076NW02591" it gives error "Sorry, this software download is not suitable for your device". then i tried different roms avaliable over internet:
RUU_Leo_S_HTC_FRA_3.14.406.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship
RUU_Leo_S_HTC_NOR_3.14.409.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship
RUU_Leo_S_HTC_WWE_3.14.405.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship
Energy.Leo.29022.Sense2.5.Cookie.2.0.XTREME.Jul.05
but every time i get the same error.
this is the info from the red, green and blue screen
PB81100 SS-BC
SPL-1.42.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
plz help me on this. im getting very frustrated its been two days and still stuck on this error.
If you cannot download ROM file from htc.com by entering your serial number you have a branded HD2, as simple as that.
Therefore you have two options:
1. gold card method (to create one you need a running Windows Mobile on your HD2), no option for you.
2. using HSPL: see this tutorial for information.
thnx for reply uli71
plz forgive me if im missing something coz i don't know much about htc phone as this is my first time im using htc phone.
when i start my phone it get stuck at red, green blue screen and does not load the windows.
can i still use HSPL?
i've tried connecting my phone with PC using WMDC but it's showing "Not Connected" and on my mobile screen it still stuck on the red green blue screen and showing this
SPL-1.42.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
i've tried the HSPL method.
restarted my phone with holding the volume down button and then connected the phone with USB cable and started the HSPL4.exe file.
it fixed the red green blue screen error but after rebooting the phone it shows HTC on white background screen and get stuck forever.
any suggestions?
anyone????????
After installing HSPL3.03 by using HSPL4.exe you should do a Task29 and then flash your prefered ROM.
For both you can use LeoAdvancedRUU.exe. Task29 is option 4, flashing ROM with HSPL is option 1.
...and both can be started from bootloader screen. (volume down and power buttons at the same time as you already know),
Task29 completed successfully. but for Tast 28 option 1 "select NBH file" dropdown is empty. how can i load NBH file in that dropdown?
Extract/decompress your downloaded RUU_Leo_S_HTC_XXX_3.14.XXX.2_Radio_15.42.50.11U_2. 15.50.14_LEO_S_Ship.exe file with 7-zip or something similar.
Then you will have the RUU_signed.nbh file.
Copy that file to the same folder LeoAdvancedRUU.exe is located and run LeoAdvancedRUU.exe as administrator (I forgot to mention that).
Now you can choose the *.nbh file.
FINALLY ........ after two days of frustrating attempts of fixing my htc .. can't beleive i actually fixed it..
thnx to uli71. you really are life savor buddy..
thnx again i did exactly what you said and it really done it for me.
You are welcome.
Now, you know the basics of flashing ROMs, you might test a custom ROM which gives you more features, more speed and the possibility to see the potential of your HD2.
My phone is doing the same thing but I accidently flashed a tp2 rom and now it gets stuck on the tri colored screen my screen reads
Hx-b3
Spl-2.08.0000 8g xe
MicroP(led) 0x05
microP(TOUCH) 0x50
When I try to hspl it says
Critcal error
Flow:00000003
Error code:00000004
Description: bad model id
Can anyone help me please
I had the exact same problem. Installed HSPL 3.03.HSPL via HSPL4.exe and then did the task 29 as advised, but then when flashing the stock ROM it went all the way upto 38% and then gave a connection error. I did the Task 29 again and tried flashing a custom ROM, flash progress did not go beyond 0% this time. Did a task 29 and tried another rom without any success. The third time I was doing Task 29 my phone disconnected during that and since then it shows no signs of life at all. Is that it, bricked?
KyleLane said:
I had the exact same problem. Installed HSPL 3.03.HSPL via HSPL4.exe and then did the task 29 as advised, but then when flashing the stock ROM it went all the way upto 38% and then gave a connection error. I did the Task 29 again and tried flashing a custom ROM, flash progress did not go beyond 0% this time. Did a task 29 and tried another rom without any success. The third time I was doing Task 29 my phone disconnected during that and since then it shows no signs of life at all. Is that it, bricked?
Click to expand...
Click to collapse
Was your battery fully charged, before you started to flash?
Have you already tried to flash with SD card method?
I apologize for a delayed response, yeah, the battery was fully charged, I did try the SD card method: put in the LEOIMG.nbh file on a freshly FAT32 formatted SD card (512 MB) and put the card in my phone, but at bootloader it didn't ask for flashing, just remained the usual, showing Serial at the bottom. That was all when it was turning on, now it's totally gone, not powering up at all.. I just need someone to say to me that it's bricked sir, please get a jtager revive your phone. somebody who knows the phone and flashing etc.
---------- Post added at 01:51 PM ---------- Previous post was at 01:46 PM ----------
I mean now that I am through with the shock of having bricked it, I just need to be absolutely sure that there is no other way that I could have tried at home to revive it myself..
Okay, so now when I turn on the phone and press the volume up button simultaneously, the phone vibrates thrice and the green LED lights up.. thats it, the screen's still totally blank..
Any ideas please?
Is my phone bricked
KyleLane said:
Okay, so now when I turn on the phone and press the volume up button simultaneously, the phone vibrates thrice and the green LED lights up.. thats it, the screen's still totally blank..
Any ideas please?
Click to expand...
Click to collapse
Man ,
I was following your instructions on post 7 . but instead of LeoAdvancedRUU 1.0.4 i flashed it from sd card . it was stuck on 25% , it vibrated 5times continously and dead after that ..I think i bricked it , anything anything at all you can do other than me changing the system board will be very very helpful .
- Have you already tried to remove your battery?
- Can you enter bootloader?
- Have you possibly tried to flash a ROM, which was not dedicated to your HD2 version?
- Was your battery fully charged before you started flashing?
- Is your SD <=2GB and FAT32 formatted?
thanks !!!
uli71
I just want to say THANKS to uli71 !!!
u solved mu problem and i realy needed to back to wm..
Thanks again..