the most obvious about my athena
ATHE100
IPL-v1.00
SPL-v1.10.0000
mo-bo has some problems like i.e. USB is not working for synchronizing and upgrade, charging is OK, microdrive is not accessible to the only option to upgrade remains via SD card
today during hard reset .... I am stuck on loop of factory reset which is supposed to do hard reset but it does not
after powering up (after completing steps on the screen) the screen is snow white and nothing happens
when I take out the battery and put it back in ... it still gets me to the same point i.e. to hard reset screen yes/no (i.e. press action to restore factory default, press camera key to exit)
can anyone please tell me :
1. how to upgrade my SPL ?
2. how to solve a/m problem ?
and possibly where to find the latest wm60 English ROM for my spl that I can install from SD card
regards
andrzej
Related
hi,
My M1000 crashed. Now it will not load windows. It will not reset (hard or Soft) . It is just stuck on a black screen which says serial on the top...and v1.06 near the bottom of the screen. Can anyone help? Is there another way to hard reset an M1000 apart from resetting the bottom and pressing power simaltaniously
You are in bootloader mode ... your rom is maybe corrupt ...
put your device in craddle and flash it
If you flash it, it should work...
TofClock is right. I have a similar problem with my Wallaby. It just won't get past the Boot screen.. You may want to use XDATools and flash a new rom to the Himalaya. You could cook one or dump one to a SD card from another M1000.
Thanks People!!!!M1000 is back from the grave!!!!!!!!!!!!
Thanks People!!!!M1000 is back from the grave!!!!!!!!!!!!
Hi,
Please help me, as its very urgent. I have been upgrading to various ROM's every now and then. Recently I did a blunder, as While upgrading with One of the ROM (Black Majik) i selected SPL 2.10 instead of Force SSPL and while upgrading USB Connection get lost.
Now I am only getting the Splash Screen showing HTC, when i Hard Reset my phone I do not get IPL and SPL version displayed and it takes my to the Splash Screen again.
Please help me in finding a way i can recover my phone.
Thanks in Advance
Regards
Try a hard reset...
If that doesn't work and you have Hard SPL on your phone upgrade using the sd card method.
As for your IPL and SPL, what do you see when you go to bootloader? That shows your IPL & SPL. To get to bootloader press power, OK button next to flywheel and soft reset with stylus. Hold all three buttons until you get to tri-colour screen. That will tell you what IPL & Spl you have.
Cheers...
Thanx for help. I could get my IPL and SPL info. But still i am not been able to get any rom installed on my device as it get stuck on that tri-color screen and rom up gradation wizards comes with different rom looks for activesync connection with the device. I am not been able to boot my device so that i can upgrade it to specific rom. Is there any way i can install a ROM without having active sync connection with the device...
Pl.. Pl.. Pl.. help. I would be greatfull to you
IF you have flashed Hard SPL on your phone you have a good Chance...
If you haven't and its under warranty you might be able to get them to fix for you.
Assuming you have Hard SPLed your phone, try the sd card method - format up to 2gb sd card fat32. copy the .nbh file from the rom upgrade to the sd card.Rename the .nbh file to "hermimg.nbh". Reset phone. As you keep going into bootloader you wont have to manually do that. It should recognize the os flash and prompt you to hit the power button to proceed...
PLEASE NOTE - THIS WILL ONLY WORK IF YOUR SPL IS 2.10 OLIPRO...
Hope you upgraded your SPL cos you will only have a paper weight otherwise..
Best of luck. Cheers...
Hi,
i flashed a rom 2 weeks ago, everything went well. yesterday i wanted to flash another os but before i could flash it, it seemed to get bricked. It stucks on the "HTC Splash" (not the WM6 Splash). I read a lot of threads and wiki threads but i don't unterstand anything! What i've to do to unbrick my phone? I tried to flash another rom but after 0% of flashing a error appears.... flashing with sd card doesn't work, too it changes to bootloader after the "Loading..." screen
i havent got hardspl or something...
please help!
UPDATE: i got the sd flashing to work... same thing but: now it stucks at the WM splash, not the t-mobile/htc one...
You need to find out what SPL you have (I'm guessing 2.03 but if you have 2.10 olipro then its got Hard SPl on it) and then do a search for "bricked SPL x.xx". You will probably find a HEAP of posts. However, some advice that seems to recover a small minority (sometimes with the "No GSM" error) -
1st thing to do is do a hard reset. Both softkeys and reset with stylus. Hold in all buttons until it asks if you want to reset to factory. Press "R" on the slideout keyboard and the "Space".
Hopefully this will fix. If it doesn't, Put it in bootloader, connect to pc (make sure "Allow USB Connection" Active Sync settings have been unticked) and run the SHIPPED STOCK ROM. This is the rom the Hermes came with originally. This MAY fix it otherwise you're in for some major reading and hair pulling.
If you should fix this then PLEASE, for the love of god, Hard SPL your Hermes before going into the wide world of flashing.....
Good Luck...
thanks i'll try it. hard reset causes kinda... nothing^^
i hope i can fix it otherwise i'll buy a touch pro
...but i think it doesn't work, because i flashed a shipped rom via sd card yesterday and the problem is still there... isn't there any way to put hard spl on my device, yet?
Try re-installing the stock rom again using sd card (if thatys how you did it last time), it could've been a bad flash. I've had those a couple of times myself. Just remember to install Hard SPL if you're successful as it makes it SOOOO much easier to recover from bad flashes.
Last thing to check would be if you have "bad blocks" using MTTY. If the boot sector has been stuffed up this may cause this problem. Do a search through the wiki, its been covered extensively...
Cheers...
okay i think my problem is solved: t-mobile replaced my device
first thing i'll do with my new device: HardSPL^^
anyhow thanks!
Upgrade successful but now stuck
I have a Three (au) Dopod 838 pro, which I upgraded from the original Windows Mobile 5 to the Three Windows Mobile 6.0 ROM. Unfortunately I didn't read up on this site first, I thought it would be straightforward since it was a ROM from the manufacturer and all, so I haven't Hard SSPL.
The upgrade reported as successful and my PC disconnected but the phone won't boot, it sticks at the Dopod screen with some numbers at the bottom. They are:
M 05 R 1.47.30.10
S 04 G 32.80.7020.20H
B 07 D 3.54
I have tried hard resetting, and returning the phone to bootloader and reflashing the same new ROM image, always with the same result.
On the bootloader, it says
HERM100
IPL-1.04
HERM100
SPL-2.03
Is there anything which can be done or is it a trip to the service centre (wherever that is)?
Just checking - Hard reset = both soft keys above the dialler closest to the lcd and reset with stylus. Hold in until it asks if you want to reset to factory. Press r on slideout keyboard then space.
This is a hard reset, not just using the stylus.
Otherwise, you have a LOT of reading material to go through with (maybe) no actual solution.
Cheers...
tried that
Thanks, but yes, I had tried that, a number of times. I think the phone will be going to a service centre today.
Hi all,
I have a Hermes here (MDA version from Tmobile UK)
We know the customer has quite literally "fingered" the unit in all ways possible
At the time, he "claimed" to be a windows mobile developer who invented WM5 - dare I say more?
OK so the Hermes is doing the following:
Stuck on Bootloader screen
Herm300
IPL-1.04
Herm300
SPL-2.03
When I do a hard reset via the two soft keys and reset button, the phone boots up with the t-mobile splash with Test Only Not For Sale
Carries on booting, goes through the whole setting up procedure
Then on the reboot, it goes back to bootloader
Now Once I managed to reset and it simply booted in with me using the phone perfectly
The second time I reset, the phone went into a white screen but you could tell it was booting up.
I'm now back in bootloader which refuses to go any further.
Tried running Hard-SPL on it but it can't seem to detect the unit despite it going from Serial to USB
Appreciate any help
On PC (if u use XP), untick "Allow USB Connections" in activesync settings. Put Hermes into bootloader and connect to pc.
Install Hard SPL. Hermes WILL be detected by the Installation program.
Then try installing a new OS, now you should have Hard SPL I'd use the sd card method.
1. Format 2Gb or less sd card FAT32.
2. Copy .nbh file of the rom you want to it and rename to hermimg.nbh.
3 Insert into Hermes and reset to bootloader, follow the instructions....
Should install a new OS and get rid of that "testing only" message.
Cheers...
I follow to your guy , so my device flash :
IPL - Ok
Bootloader - ok
GSM -
It hand on there.
Can you held me now.
My device 's Softbank X01HT, I reflash original ROM (Japanese language)
i searched the forum for 4 days tioo have a clear solution for thos 2 niki100 i recieved the stuck at the operator logo tim from brazil i dont know what my clients did to them but apears the they try to play over upgrading any way im looking for reflashing the same rom to have them back a life again.
i tested many thread posted here buy members i downlaoded many rom that never works with this kind of problem but when i found the mtty command task 2a then boot one of them turnd with a white screen but stell enter boot mode well for peopole how like to help me the spl on the boot mode is
spl 1.21
R 1.58.21.26
G 25.65.30.04H
D 1.35
VENDOR ID TIM BRAZIL
PLEAS GUYS I NEED TO SLEEP ANY HELP FROM EXPERTS WELL BE GOOD AND USEFULL
REGrds to alll
I need this original rom as well, not possibile download from oficial site....Serial number not acepted!!
Phone stuck on operator logo...cant hard spl!!!
is it any of these...
http://shipped-roms.com/shipped/Nike/
DT
Cant see mine R 1.58.21.26....anyway thx!!
theres other way to revive my Niki?
edcentec said:
Cant see mine R 1.58.21.26....anyway thx!!
theres other way to revive my Niki?
Click to expand...
Click to collapse
These are possibly updated versions of your area's stock ROM, the 1.58 radio would be a version 1 ROM, where the 1.65 radio are the version 2 ROMs.
Does it have Hard SPL installed? If not, see if it will install it, then you can install any ROM.
There are other things that can be tried using MTTY, but I am no expert on that - there is a thread on it though.
DT
Could you tell us what you did, I mean did you already tried a hard reset or something simular, and which rom you where using when the phone freeze.
Hard reset
You can also perform a hard reset (also known as a full reset). A hard reset should be performed only if a normal reset does not solve a system problem. After a hard reset, the device is restored to its default settings -‑ the way it was when you first purchased it and turned it on. Any programs you installed, data you entered, and settings you customized on your device will be lost. Only Windows Mobile® software and other pre-installed programs will remain.
To perform a hard reset
1. Press and hold the TALK and END buttons, and at the same time, use the stylus to press the RESET button at the left side of your device.
2. Release the stylus, but continue pressing the TALK and END buttons until you see the following message on the screen:
3. Release the TALK and END buttons, and then press ENTER on your device.
Warning! Your device will be set back to factory default settings. Please ensure any additional installed programs and/or user data have been backed up before a hard reset is performed.
Important If Encrypt files placed on storage cards is or was enabled before, then backup all files from the storage card before using Clear Storage, hard reset or updating the ROM system software. Otherwise you will no longer be able to access the encrypted files on the storage card. Use ActiveSync or Windows Mobile Device Center to transfer files between your storage card and computer. After the procedure, copy your files back to the storage card.
Click to expand...
Click to collapse
Greetz,