Hello, I flashed athena ap4 rom
and stuck at gray loading screen
-the one that was suppose to show percent progress but now stuck there
and said "loading"
-when i get back to bootloader using hardward button
-it will get there and go straight to gray loading screen again
-flashing using sdcard was unsuccessful also
any suggestiosn, thanks
Remove minisd & sim card from your device
Go to bootloader using hardware button
Connect your device to PC using USB cable and then try to flash a new Rom
Good Luck...
Fixed! Thanks for you help!!
HELP
Solved after retrying a few times...now is really looking at Hard SPL the device so that I can change the ROM from CHT to ENG...
Thanks.
Related
hi,
i've searched, and am stuck. i tried to flash a new ROM today, but it stopped at 76% and said no connection!?? i've flashed before with no problems many ROMs. I have HardSPL 1.15 mfg installed and everything always worked. Now i'm stuck at 4 color boot screen screen. HardSPL is still there, there is a message at top right saying 'RUUNBH'. I plug USB in and it says 'USB'. I run mtty but can't seem to get any CMD, or even type 'boot' in, no response on app, running on XP?
i'm reeally stuck, and had to come to work, so am worried. can anyone help??
sorry, i am still searching for solution, but please any help appreciated!!
thank you
i will try to check back often, but stuck at work might be problem ..
i got stuck at that boot screen too, but it happened during a boot image change operation. All I had to do was install a new rom.
Hope it helps...
how did you install a new rom? cos i cant activesync, and running CustomRUU.exe says it cant find pda device
am i bricked? really stuck here :'(
badaas said:
how did you install a new rom? cos i cant activesync, and running CustomRUU.exe says it cant find pda device
am i bricked? really stuck here :'(
Click to expand...
Click to collapse
Don't worry, you just need to get to the bootloader screen and flash again, you may have a corrupted update that may hault everytime. If it doen't work try another ROM.
Hold down power and the camera button while pressing and holding the reset button.
When you see the Boot Loader screen you can release all three.
Plug in your cable if it is not already, wait to make sure the computer installs the device and then run the ROM Update executable you want or ROMUpdateUtility.exe if everything is placed in a folder.
Note: Activesync and Mobile Device Center will not launch in this mode, and if the utility tells you to connect through activesync or Mobile Device Center ignore and continue.
OK thank you my friends, i will try when i get home from work. fingers crossed!!
cheers
thx guys, all sorted
I attempted to use SSK 2.6 R4R Gen.Y Edition Default Kitchen from
HTML:
http://www.sskusers.net/
on my phone earlier. It seemed like everything was going fine, until I was taken to the startup screen. It was frozen, and there was red writing at the bottom of the screen.
Because the phone is stuck on that screen, when I try to connect to ActiveSync, it doesn't recognize any USB devices.
I did try removing the battery. The phone turns off, obviously, but when I turn it back on, I'm back at the frozen startup screen again.
I have also tried doing a soft reset, and the hard reset. When I do a hard reset, it takes me to the bootloader screen, and lets me do everything, but when it reboots, I just end up in the same place I was before - with a frozen startup screen.
Any suggestions on what to do, and/or what could have caused it?
Just wanted to add:
I have Verizon, and did do the hard spl using Raphael_VZW_HSPL_035, which I got from
HTML:
www.ppcgeeks.com
Reflash a different ROM through usb from the bootloader.
dwizzy130
i would suggest flashing a new rom or maybe going back to stock first & then trying a new rom. i would say the most important part right now would be flashing from the bootloader. put the nbh file on the sd card using a media reader & then pop it back in the phone & flash it. thats the easiest way & wouldn't take but 10 minutes to accomplish. i wouldn't be too worried you should be fine. feel free to get at me privately if you need some help.
Help
If you installed Hspl then just hold volume down and power and press the soft reset key. it will reboot into the bootloader and will recognize via usb. Hope this helps. I had a endless loop when i tried flashing to energyrom and this got me back to mightyrom. u may want to try it http://www.mightyrom.com
Hi all,
I have searched all over and can't figure out what is my problem. Any help would be greatly appreciated. I have TMO US H2. I've been trying to flash my phone for a few hours to no avail. I have tried to flash a few different ROMs via ActiveSync and I get an error saying it lost connection after it tries to access the bootloader. I then tried to flash it via the SD card, but can't get past the tri color screen, even with a signed ROM.
The tri-color screen shows the following:
PB81120 HX-B3
SPL-2.00.HSPL 8G XE
0x05
Cotulla aHSPL 0x50
Can anyone tell me why I can't seem to get past this screen when trying to flash a ROM?
Sounds like a task for task29. Search for it in this forum, and after you perform it - load a proper rom to your device.
I tried task29 but when it gets to the bootloader it gets stuck on the tricolor screen and says USB at the bottom, just like all the other times I tried to flash it. I get the following error message:
Error [302] - Update Error
The ROM update utility has encountered communication errors during the update process. The program will guide you step-by-step to recover from the errors so you can continue with the update.
What am I doing wrong? I keep seeing this error message every time.
so you can't even load a ROM from the sd card? that eliminates a bad usb.
You put a Rom image on the root of your sd card (usually needs to be 8gb or smaller). You make sure it is named LEOIMG.nbh. While pressing in the reset button (by the battery), you hold down the volume down button. Your phone should go into bootloader (tricolored) momentarily, then switch to a grey screen that asks if you want to update. press power for yes or vol up? for no. You press the red (phone call end button) and it errors? Is this what happens?
many people report the supplied 16gb card doesn't work for flashing.
for usb flashing, enter bootloader manually. wait for serial to become usb, and then run the flash.
im having the same problem. i have hardspl, i falshed a radio 2.07.50 just fine, then i tried flashing the rom via computer, the bootloader screen would not display the grey coloured screen where you 'update image' and it said lost connection on my computer. I then tried the sd card way, LEOIMG.nbh, same result - no grey screen to 'update image'
these are my problems when i accidentally flashed a not so clean rom and unstable one:
1.) when the official screen logo welcome appears... it doesn't show any information about the rom like
ipl 2.xx
spl 2.xx
radio etc..
the welcome logo screen itself.
2.) i cannot charge my phone when it is turned on. the only way is to turn it off..
-this gives me another problem when it comes to syncing my 02 xda atom.. since it does not recognize any usb connections when it is turned on..
3.) wifi doesn't turn on?,, when i tap the toggle in the comm manager, loading icon will show for about 10-15 seconds and leave the wlan still turned off,,
i tried to flash helloworld wm6.1 using sd card since my 02 atom cannot recognize any usb connections when it is turned on.. in bootloader mode i've waited for 20 mins as it is expected to boot for that span. but still nothing happened. it did not work. bootloader mode did not show any sign of progress.
i've read some threads that there are registry edits that disables charging through usb connection.. but can't find it in the net.. any idea??
any possible solutions??
help!!!
thanks....
try to soft reset your device, if you still get the same problem go to the bootloader (three color screen) then reflash again ..! try the Flash ROM by manufacturing your device... good luck prince
I had installed Chucky rom(ChuckyROM-23136-Tabtastic.Sept.12.7z) on my htc hd2,i had also installed hspl( HSPL2_RUN.exe) around two months(in september 2010) back but i did not like it so today(25th november 2010) first i removed hspl through HSPL3_PKG.exe and put spl 2.08.0000( I DID NOT USE AN SD CARD TO FLASH THE SPL) and then flashed
Artemis_v430_0409_WWE.7z i.e RUU_Signed_0409.nbh through SSPL_RUU.exe and then it worked and was working properly but was hanging again and again so i soft reseted it two-three times and then i was installing a cab file but as soon as the installation started, it said "installation of so and so file.cab was unsuccesfull" then i tried dinik hybridia icon .cab again same thing happened so i soft reseted it and while soft reseting a complete black screen appeared and said "a program from an unrecognised software party was tried to install please press the upper volume button to reset the phone Note. you will lose all your data and the phone will completely reset itself or else press any other button to start normally" i pressed any button so it started loading normally but it has got stuck at that loading and is not doing anything after that ,
it is not connecting to the pc,the backlight of the keys is also not switching on , i have takin the video of it switching on and also of bootloader ,
what has happened to it and why is it not starting,please help?
also even after i flashed artemis gen 4 it is showing the chucky rom boot screen!
In the videos it gets stuck to where i have stopped the video and remains like that for hours(THE Video IS IN THE RAR FILE)
also i have warranty left so can i get it repaired by warranty???
PLEASE HELP ASAP
try a hard reset. turn the phone off, hold down both volume buttons, and turn the phone on, keeping the vol buttons held down. then when prompted,press vol up to reset it.
yes, you'll lose any data and modifications on your phone, it will be back to how it was right after you flashed it, but at least it will start up. better than how it is now, right?
nishankyadav said:
I had installed Chucky rom(ChuckyROM-23136-Tabtastic.Sept.12.7z) on my htc hd2,i had also installed hspl( HSPL2_RUN.exe) around two months(in september 2010) back but i did not like it so today(25th november 2010) first i removed hspl through HSPL3_PKG.exe and put spl 2.08.0000( I DID NOT USE AN SD CARD TO FLASH THE SPL) and then flashed
Artemis_v430_0409_WWE.7z i.e RUU_Signed_0409.nbh through SSPL_RUU.exe and then it worked and was working properly but was hanging again and again so i soft reseted it two-three times and then i was installing a cab file but as soon as the installation started, it said "installation of so and so file.cab was unsuccesfull" then i tried dinik hybridia icon .cab again same thing happened so i soft reseted it and while soft reseting a complete black screen appeared and said "a program from an unrecognised software party was tried to install please press the upper volume button to reset the phone Note. you will lose all your data and the phone will completely reset itself or else press any other button to start normally" i pressed any button so it started loading normally but it has got stuck at that loading and is not doing anything after that ,
it is not connecting to the pc,the backlight of the keys is also not switching on , i have takin the video of it switching on and also of bootloader ,
what has happened to it and why is it not starting,please help?
also even after i flashed artemis gen 4 it is showing the chucky rom boot screen!
In the videos it gets stuck to where i have stopped the video and remains like that for hours(THE Video IS IN THE RAR FILE)
also i have warranty left so can i get it repaired by warranty???
PLEASE HELP ASAP
Click to expand...
Click to collapse
What an utterly unfortunate situation!! Couple of questions/remarks:
1. Did you install HTC 3.14 ROM with your S/N from HTC's website before flashing Artemis?
2. You already removed HSPL, so I would advice to extract the 3.14 RUU file to your desktop and copy the custom.nbh file to your SD Card after having it renamed to leoimg.nbh (insert SD CArd into PC to do that).
3. Reinsert SD card in device and enter bootlader mode and the installation of 3.14 should start automatically.
4. After that download Artemis 43 and extract it to the folder where you're SSPL_RUU,exe resides. Bothe the custom.nbh and the SSPL file must be in the same folder!
6. Start SSPL_RUU and flash Artemis
7. After that first a hard reset and then a soft reset.
Also read page 1 - Flashing notes
This should to it for you,
regards, Kuzibri
P.S. I posted this also in Artemis thread
same problem
i've got the same problem, but i didn't install the rom artemis,
i restart the installation many time but i've got always the same problem
the display showing loading..... please wait with the chucky logo.
someone can help me???????
thank you