Pls help, I had flash several roms but usual stop at 9%, error 290
SPL-2.08.hspl 8G XE
0x05
CotullaHSPL 0x40
wtanph said:
Pls help, I had flash several roms but usual stop at 9%, error 290
SPL-2.08.hspl 8G XE
0x05
CotullaHSPL 0x40
Click to expand...
Click to collapse
HI
use different USB port from back of the PC. If your PC runs on Vista or windows 7 then "Run as administrator.
Also Put the device on bootloader then use Custom ruu to flash any roms.
Good luck
iam using window 7 home primium 64, acer notebook, i had change to other usb port, it increase to 16% then hang, error 264, everytime i power the device it display the bootloader, thanks
sabes143 said:
HI
use different USB port from back of the PC. If your PC runs on Vista or windows 7 then "Run as administrator.
Also Put the device on bootloader then use Custom ruu to flash any roms.
Good luck
Click to expand...
Click to collapse
wow i got error 290 when I upgrading radio
and i run the custom RUU as adminstrator
it solved wowowoo
Try to change the radio. I use 2.15.50.14 and it work fine for Nand rom.
I solved it installing shipped leoimg.nbh by SD card... but never more successfully upgraded the phone through another shipped rom (by RUU).
Never understood why this happened.
Does your S/N starts with something different than HT***?
Related
Hello all... tried to be a little geek and installed a custom Rom (Artemis V32 with radio 2.12.50.02_2) and that went ok. Then I copied an Android version to my sd card, and that went also ok.
Then I installed a bootloader so I could choose Android or WM, that went ok too.
But since then I had some regular crashes in Android and also with WM.
I decided to install a stock Rom (found via Usenet; Stock ROM (NLD) 1.72.172.0 met radio 2.07.51.22_2 en SPL-1.66.0000 ) and things went bad.
I have tried all kinds of things so resolve the issue:
- Put the stock rom on the sd card (formatted fat32, size 4gig) and renamed it to loeimg.nbh and started it up with the volume button down: no success
Message:
PB1100 HX-BC
SPL-1.66.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
- Connected the hd2 with the original cable to my pc (Windows 7 Ultimate, and tried also WinXP SP3) and tried to install it via the .exe file from another stock rom I downloaded via the HTC website.No succes, the software starts-up, I can click yes, next, click yes again at "I completed the steps indicated above" and then I get the screen current information about your pda phone Image version does not mention any version at this point.
If I then click on update I get the screen that says from image version: to image version.
The from version is not filled in, so I think the fault has something to do with this.
After I clicknext 2 times I get the progress screen, but nothing happens then anymore. It keeps showing 0%
If anyone can help me out with this it would appreciate it a lot! And if you need any additional info, please let me know...
Thanks in advance,
Friendly greetings...
you no longer have hspl installed. It was removed by the (failed) stock rom from sd card flash attempt. In bootloader, see your spl ends .0000? that tells you hspl is gone.
Manually enter bootloader, connect usb, count to 20, run hspl2(right click run as administrator), choose 2.08.hspl.
When it completes, re enter bootlaoder (hold down vol as the phone restarts at 100%), wait for bootloader, wait for the word serial -> usb, run your rom flash over usb.
Thanks for the quick reply... as soon as I'm back home I'm going to try it out.. I'll post the result here..
something similiar happened to me some months ago..
should work
DN41
oh, and the reason the "from version" is blank is because that is read from the registry, but we put the phone in bootloader ourselves first so it can't see the registry. that's also why when you flash radios you see rom version info there. it can be ignored.
Do not forget to remove loeimg.nbh from your memory card before trying to flash under windows.
Thanks for the reactions... great to know I am not alone in this...
I performed the actions as described and I got the message "we hacked it"
I then tried to install a stock rom I downloaded but my phone turned off then at 11%
I have the idea that my battery is not loading anymore as I can't see the orange led burning when connected to the adapter/computer.
Ordered a new battery yesterday evening and will receive it normaly/hopefully today by mail. Then I will try again and share the results.
Thanks again all for the great support so far...
check the battery pins closely, hundreds of people have bent them poppng the battery out.
Ok, checked the connection of the pins.. these are ok I think.
Battery-led is still not showing went connected to usb.
So now my screen states the following:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CottulaHSPL 0x40
What rom can I now install? Only an official one?
I tried to download an official rom from the htc website (after inserting my serial), but when I run the
RUU_Leo_Vodafone_NL_1.72.172.0_Radio_CRC_Signed_15.32.50.07U_2.07.51.22_2_Ship it shows a message that the file is corrupt.. and this for about 6 times now...
I feel the noob-level is rising extremely now...
TitusV said:
What rom can I now install? Only an official one?
SPL-2.08.HSPL 8G XE
Click to expand...
Click to collapse
.hspl means hspl is installed so you can flash any rom.
I tried to download an official rom from the htc website (after inserting my serial), but when I run the
RUU_Leo_Vodafone_NL_1.72.172.0_Radio_CRC_Signed_15.32.50.07U_2.07.51.22_2_Ship it shows a message that the file is corrupt.. and this for about 6 times now...
(
Click to expand...
Click to collapse
all i can say is try another rom. just stick to usb flashing, protect hspl.
I have HTC HD2 t-mobile version. my phone now is broken i am not sour should I do with it anymore. it stuck at 1st screen. please help me
this my spl
PB81120 HX-B3
SPL-3.03.HSPL XE
0X05
CotullaHSPL 0X40
T-Mobile.com
Get latest 3.14 rom
From bootloader (stripey screen)
Plug in USB cable
Run 3.14 rom.exe
Report results.
I download that it is install 8% and error
samsamuel said:
T-Mobile.com
Get latest 3.14 rom
From bootloader (stripey screen)
Plug in USB cable
Run 3.14 rom.exe
Report results.
Click to expand...
Click to collapse
What did you do last before this issue occurred?
Search for "task29" and do this, that might also help. After that flash with your favorite rom(probably the one you were trying to flash)
You can also look on youtube for "task29 hd2" for some tutorials.
I was change my phone to andriod but I don't like it. so I want to change it back to window mobile when I doing it. it is error . so I try flash different radio and how it error. anyone have any idea how to make my phone working? I need phone to use please help me
thanks so much
Marvlesz said:
What did you do last before this issue occurred?
Click to expand...
Click to collapse
Note: I've seen a few similar threads with a problem like mine, but my HD2 is showing different error messages, so I thought I'd start a new thread to avoid making things worse.
---------------------------------
So I purchased a second hand HTC HD2 pretty cheap. It's the 512HD2 and it came flashed with a MIUI Android with a Samsung Galaxy S2-ish interface. Problem was, the battery got drained way too quickly, even from the most minimal usage, so I though I should flash back to the stock OS and get my problem solved so I could use the HD2 as a primary phone.
Here's what I did:
1. I followed jayceooi's tutorial.
2. I downloaded a ROM Update for HTC HD2 (3.14.405.2) from HTC's Official HD2 download page.
3. I opened up the .exe, got the .nbh, renamed it correctly, put it on the SD card and then verified it's really there with an Android file manager.
4. VolDown + PowerButton and I got to the rainbow menu thing (I know, I'm a noob and I don't know how it's called) then I let go of the keys and got to the update screen.
5. PowerButton - Update begins
6. 30 seconds later, only after about 1/4 of the bar had progressed, I got a black screen, and then a screen that says "Software update failed. Please try again". Afterwards the gray screen saying "Loading... 00028002 not allow". Finally, back to the RGB screen I got:
HX-BC
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
And If i try to enter the boot mode via VolDown+PowerButton I get:
RUUNBH
HX-BC
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
Update ROM code error
Please try again
Serial
---------------------------------
Should I try a USB flash or something?
Thanks in advance.
?
Nobody?
Update:
I tried to upgrade from 3.03.0000 SPL to the 3.03.0000 HSPL via USB in the boot mode, but I got a critical error and nothing happened on the device whatsoever - same state as the post above.
Any ideas?
probably wrong stock rom used, (or did you use the phones correct serial to download the rom?)
enter bootloader (three coloured screen)
connect usb
run hspl4
choose 3.03.hspl
back into bootlaoder
connect usb
run the 3.14 rom over usb.
EDIT - just saw your edit about critical error, , ,win7 64bit? try different usb ports, and try a different pc if you have one available, , hspl can be a little picky.
samsamuel said:
just saw your edit about critical error, , ,win7 64bit? try different usb ports, and try a different pc if you have one available, , hspl can be a little picky.
Click to expand...
Click to collapse
Unfortunately I have only one laptop with a 32 bit Win7, but it's OLD and crapfull of viruses so I'm not risking any failures there.
Do you think it will be safe to HSPL over VMWare (virtual OS environment inside of windows)?
P.S.: Exact model is the HTC HD2 T8585. I checked it via an IMEI checker.
there's a very good chance that hspl wont flash from a virtual machine. (Something about not getting low enough level access to the usb or something).
samsamuel said:
there's a very good chance that hspl wont flash from a virtual machine. (Something about not getting low enough level access to the usb or something).
Click to expand...
Click to collapse
Ok, in that case I'll probably go over at a friend's house and try an HSPL there. I'll come back with some results as soon as I'm done.
Halfway done?
OK, so I got a good Windows 7 32 bit laptop and tried out HSPL4.exe by DFT. I kept my fingers crossed and, thankfully, I got to the "We hacked it! " screen.
After successfully updating and removing the USB cable, the phone rebooted with the same "Software Update Failed" message, but this time the gray screen showed the Cancel/Allow for the leoimg on the SD. I pressed the power button to attempt a flash, but I got the same issue as last time.
After that, the VolDown + PowerButton STILL showed:
SPL-3.03.0000
Since I'm not that stupid (I hope) I figured that the ROM reverts SPL and Radio to normal and that's why there was no trace of the HSPL, so I went back to the laptop to go at another 3.03.0000 HSPL. This time, after I got the "We hacked it! " screen I cancelled the ROM update and thankfully the RGB screen now reads:
P81100 HX-BC
SPL-3.03.HSPL XE
0x05
CotullaHSPL 0x40
IN SHORT - The HSPL was a success, now if you help me find the right ROM, I would owe you my life!
lol, i draw the line at advising roms, for example ive never used an android rom with sense, or a MIUI rom, and i havent used a winmo rom in about a year,, so it would be unfair of me to guide you.
ROM
Edit - Okay, thanks for all your help!
P.S.: I just ran an Task29 to get rid of the constant Software Update error at each boot and now I can boot into the RGB screen without the RUUNBH error so I think that will make things easier. I'll probably find the ROM myself or ask somewhere else.
Thanks again!!!
thanks
samsamuel said:
probably wrong stock rom used, (or did you use the phones correct serial to download the rom?)
enter bootloader (three coloured screen)
connect usb
run hspl4
choose 3.03.hspl
back into bootlaoder
connect usb
run the 3.14 rom over usb.
EDIT - just saw your edit about critical error, , ,win7 64bit? try different usb ports, and try a different pc if you have one available, , hspl can be a little picky.
Click to expand...
Click to collapse
if you were a girl I would kiss you
You saved my day. I was searching for my problem since 3 days and this has solved the problem
Finally Done!
@ParmakSokan - Hey! Looks like I'm not the only one samsamuel helped!
A little update - I finally have the phone in working condition! It is now running the stock Windows Mobile 6.5 specific for O2, since I figured out the device was purchased in the UK.
For anyone interested, I got the ROM from the official library of HD2 ROMs in 4shared, which I believe is held together thanks to xda-developers, so yeah - yet another KUDOS for that!
The HTC Sense UI is simply beautiful and I think I will actually stay with 6.5 for a few more months before considering 7.5 Mango.
P.S.: Moderators can mark the thread as solved.
Hi
I have a flashed HD2 with these problems.
In Bootloader it says
PB81100 SS-BC
SPL-208.HSPL 8G XE
0X05​CotullaHSPL 0X50
If I try to install HTC RUU_Leo_S_HTC_GER_3.14.407.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship.exe it breaks after 1% it says 270 error
HD2 reboots and again white Screen. When I put off/on battery and press Volume down I see bootloader display.
I tried to flash with sd Card, leoimg.nbh on the sdcard breakes after 10%
it says
00018003
LEOIMG.nbh -FAIL
Radio-Fail
I think I have a bootloader problem. How can I remove SPL-2.08.HSPL 8G XE and set the new orginal SPL ?
here bepe says :
4) Uninstallation
Only way to remove the HSPL is to flash an original SPL from SD card.
- Take any "RUU_signed.nbh" from a ship ROM and copy it to SD card.
- Rename it to "leoimg.nbh"
- Reset the device while pressing the volume down button.
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=611433
I made it with HTC
RUU_Leo_S_HTC_GER_3.14.407.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship.exe
but I can't remove HSPL from my bootloader.
How can I set my bootloader back to original htc ?
the topic can be closed
this has solved my problem
http://forum.xda-developers.com/showthread.php?p=24876999#post24876999
I had installd Windows 6.5 everthing was working perfect, then I tried to install Android and clk mod now I get the same in the 1. Posting from me.
I have SPL-3.03 HSPL in the boatloader but I get allways Error 270 I can't uninstall 3.03 HSPL
does anybody have an Idea?
Radio_2.15.50.14.nbh installation fails, but custom rom like energy sucesses. After that again white screen
nobody knows the solution?
You have a stuck radio. Fairly common, with a variety of symptoms. The radio wont let itself be changed which is why custom roms and splashscreens don't have a problem.(radio gets flashed at the start of flashing which is why it always fails around 8-10%) This issue can affect spl to a greater or lesser degree, some people can change spl some can't, some find flashing an older (but correct for that phones cid and region) stock rom, some find chilling the phone allows the flash to take allowing the radio to finally change, some never get anything to flash again.
hi
thank you for your answer. My Bootloader shows
SPL-3.03.HSPL XE
0X05
0X50
if I try to run Task29 via USB Cable, I get Error 270, it breaks sometimes at 16%
reflash 3.03 HSPL with HSPL 4 says it is successfull, but if I try to flash a rom with usb again it shows 270 Error, so my logical deduction is, reflash with HSPL4 does not really flash and it gives wrong answer because others like task28 leo customRUU can't flash over usb cable. HSPL 4 says success but this answer must be fake, after reboot 3.03HSPL remains in the bootloader, I tried to downgrade to 2.08HSPL no chance,
My System is Windows XP SP3 when I connect USB Cable to my HD2 it shows USB in the bootloader but why does it break if I try to flash over USB Cable and give an error 270 ? there must be a connection problem between my laptop and HD2.
I would like to know
Is there any way to flash HSPL4 over microSD card?
Can I see which Radio Rom has been installed ?
its a bit strange
Radio Rom Radio_2.15.50.14 istallation via USB Cable fails after 4%
and via microSD Card ~96-99%
I get
00018003
what can be the reason?
ParmakSokan said:
what can be the reason?
Click to expand...
Click to collapse
as i said,. you have a radio image that isnt allowing itself to be overwritten. My name for it is 'stuck radio' and some people fgind the radio still works fine with, for example, custom roms, it just cant be changed, others find the phone always hangs on grey bootscreen, yet more find taht hspol/spl flashes seem to work but nothing changes, some find chilling it in teh freezer lets a rom flash and suddenly all is well, and yet more find the freezer trick seems to work but doesnt, and yet more try and try and try to sd card flash with their CORRECT stock rom and suddenly without warning teh flash works.
My advcie, Prepare yourself for disappointment, but keep trying,and most importantly READING there are hundreds of threads about this.
mobile radio
ParmakSokan said:
nobody knows the solution?
Click to expand...
Click to collapse
hey gys whats this radio in mobiles... have searched and searched but no ans.....
hi all, I hard formatted my windows phone 6.5, HTC HD2 and started setup for HSPL3 For HTC Leo. The setup started and failed and i'm stuck with it now. it gives me screen
HX-BC
SPL-1.42.0000 XE
MicroP(LED) 0x05
Micro(TOUCH) 0x40
and when i start phone power+volume down with leoimg.nbh in SD card the screen says
PB81100 HX-BC
SPL-1.42.0000 XE
MicroP(LED) 0x05
Micro(TOUCH) 0x40
Upgrade ROM code error. please try again
Serial.
Please help!!!
Common issue:
You still have standard SPL installed & thus require a ROM that is correct ROM code of original country/operator which the one on your SD card is not hence "Upgrade ROM code error"
Your 2 options are:
1. Use HSPL 3 or 4 to install a HSPL which bypasses CID lock & allows you to flash any ROM but by USB & RUU, if do from SD it overwrites HSPL with SPL everytime
2. Find a compatable CID code ROM & flash it ...
If this is a T-Mobile USA handset make sure to flash a ROM with correct radio or you will have a brick ...
Mister B said:
If this is a T-Mobile USA handset .
Click to expand...
Click to collapse
it cant possibly be a tmous with 1.42.0000 spl.
@OP, you are in the wrong forum, this is for tmo usa model hd2 only. (That's why there's so few recent posts, , , most tmous users are now in the android forums.
With the phone in the stripey screen (bootloader) connect usb, , when 'serial' changes to 'usb' you are ready to try running hspl again. What are you aiming for? if its android, (meaning your target is 2.08.hspl) use HSPL2 instead.