Hello,
I try to flash my T01A like that
Fully Charge.
Unrar SDDL.rar,copy all files to storage card
Unrar T01A_to_SP50_wm65-new_theduyet.rar and Create prg folder in storage card and copy enc file after unrar into it.
Remove the SIM Card
- Remove the black plastic tab under where the SIM lies
- Replace the battery
- Secure the battery - use Velcro cable tie, rubber band or sticky tape [vital it does not fall out while Flashing ! ]
- Short (connect together) Pin 1 and Pin 3; then press the Reset Button
- Hold for 10 seconds or so; then release
- Turn phone over and should show white Flash screen in progress until completed and says Successful - Rebooting
Shorten pin Method
Click to expand...
Click to collapse
I do all like in instruction but flash don't start(
Then I see new instruction
remove stripe under sim.
secure the battery in place with duct tape so it will not fall out.
power the phone.
shortcut pin 1 and 3 an press reset.
release reset
keep shorting pins 1 and 3 for couple of seconds.
stop shorting and turn the phone with screen up.
Click to expand...
Click to collapse
So when I "shortcut pin 1 and 3" and press pwr button, tel start vibration for one second, after 10 second I stop shorting, I turn the phone and have a black screen.
Now telephone don`t work, when I press pwr button screen still black.
Can you help me? sorry for my poor English, I'm from Russia.
batias said:
Hello,
I try to flash my T01A like that
I do all like in instruction but flash don't start(
Then I see new instruction
So when I "shortcut pin 1 and 3" and press pwr button, tel start vibration for one second, after 10 second I stop shorting, I turn the phone and have a black screen.
Now telephone don`t work, when I press pwr button screen still black.
Can you help me? sorry for my poor English, I'm from Russia.
Click to expand...
Click to collapse
o
Youe case is like my case but sorry i also don't know how to fix it too.
i have to sent it to docomo shop and tell them it broken while upgrade the official rom..it take 1 week and no charge ........
Put the phone on charger for 4 hours even if it doesn't light
Then follow instructions in: http://forum.xda-developers.com/showthread.php?t=682480
Use the downloader on Win XP computer
It worked for me
Hope works to you
All thanks for answer.
It worked for me
Hope works to you
Click to expand...
Click to collapse
Unfortunately did not help for me. Power controller die.
Is it possible somewhere to buy spare parts?
Related
I have an s200 device. My s200 had a small crash in the floor (from my pocket) and from that moment when I press the power button the only thing that happens is that the screen turns white and after few seconds Grey and then black...
I connected to the pc but it always seems to find and then loose the device (after 1 second).
I tried hard reset...nothing (press comm button and the pin in the soft reset)
Is this dead? I am desperate so many days
Solution
1st. u've 2 start ur pda in bootloader mode (triple colored screen).
2nd. Connect it 2 PC and use ActivSync 4.1
3rd. Install the rom u want.
4th. 've FUN !!!
luverh8r said:
1st. u've 2 start ur pda in bootloader mode (triple colored screen).
Click to expand...
Click to collapse
I can't start in bootlader mode any suggestion?
vamvakoolas said:
I have an s200 device. My s200 had a small crash in the floor (from my pocket) and from that moment when I press the power button the only thing that happens is that the screen turns white and after few seconds Grey and then black...
I connected to the pc but it always seems to find and then loose the device (after 1 second).
I tried hard reset...nothing (press comm button and the pin in the soft reset)
Is this dead? I am desperate so many days
Click to expand...
Click to collapse
something happening with lcd connector or lcd driver.... try to disassembly and check conectors and board integrity...
Hi All,
I have flashed EUViewPad 7 based on Stock rom. installed SD Card Booster, CPU Master and etc.
The flash is fine since I managed to boot it and install several apps.
Until I needed to reboot the device since the hacker keyboard always forces to close. I rebooted it and poof I am in infinite boot animation without a way to remove the battery. afraid to fiddle just waited the battery to drain so I can test again(This happened on my O1. just removed the battery, put it back and its ok)
I have drained the battery after almost 8 hours of non stop boot animation. But this device won't turn on anymore. It just vibrates when I press the on button.
Tried opening the back(crap I have scratched the back covering. now it has large scratches ) but the battery is taped . My question folks is what is the possible solution to my problem aside from removing the battery(can't even get to clockword recovery)
Thanks
Not too sure about your device, but doesn't yours have a reset button like the viewpad?
Should be a small hole on the bottom edge right next to the microphone.
Try pressing that with a paperclip if you're having boot problems.
Anyway, if you've drained the battery completely, make sure to leave it charging for a little while. Too low battery voltage will make it unable to start. 15 mins or so should be more then enough.
Try starting with both volume buttons + power pressed. Keep holding it until you see "entering recovery mode."
Let me know if this gives any results.
Amalgation said:
Not too sure about your device, but doesn't yours have a reset button like the viewpad?
Should be a small hole on the bottom edge right next to the microphone.
Try pressing that with a paperclip if you're having boot problems.
Anyway, if you've drained the battery completely, make sure to leave it charging for a little while. Too low battery voltage will make it unable to start. 15 mins or so should be more then enough.
Try starting with both volume buttons + power pressed. Keep holding it until you see "entering recovery mode."
Let me know if this gives any results.
Click to expand...
Click to collapse
Ahh I have that reset button beside the microphone hole. Will try this later on. Thanks for your help and for your custom rom
Uh oh... Tried pressing the small hall beside microphone, pressed on button. No luck. tried pressing that hole and on at the same time No luck again.
Is it possible that it will mess up the whole boot process due to boot animation loop??
silencer07 said:
Uh oh... Is it possible that it will mess up the whole boot process due to boot animation loop??
Click to expand...
Click to collapse
I'm afraid and it sounded like, from your descriptions, that the boot process has been messed up .... so, what do you got to lose by trying to "wake" it up or at least respond to commands, right ?
Try holding the power button & use a small pin to press RESET - leave it connected to the power supply/charging unit.
Try holding both volume Up & Down key & use a small pin to press RESET
Try holding both volume Up & Down key along with the Power button at the same time, and press RESET (you might want to get someone to help you to this)
Try holding the volume Down (left) key & Power button, and press RESET with a small pin.
Does any of these work in getting the screen to show life, be patient as you might have to hold it for 10 to 30 seconds before it cycle & restart/display the 3 birds ...
Chances are you will need to flash a stock ROM with the SULT3 utility, and then if successful, root it again & start over (carefully) - it might work or it might not even connect via usb at all .... worth a try, got nothing to lose at this point.
As a last resort, contact Cherry Mobile and get it repaired & sending it back to the shop .... check the warranty details in your locale, opening the rear case & exposing the battery, might or might not void your warranty coverage.
Hi Letiride,
I have tried the combinations you have specified but no avail. I can't boot this so my PC with correct drivers cannot even recognize i plugged this.
Is my Tablet already bricked?? I have bought this second hand so no warranty already.
Huhuhu Did I already have one of the "Vibrator" Android phone
silencer07 said:
tried the combinations but no avail. I can't boot this so my PC with correct drivers cannot even recognize i plugged this.
Is my Tablet already bricked?? .... bought this second hand so no warranty. (
Click to expand...
Click to collapse
Oh mine, no - if it won't power up or boot into Recovery or FTM mode, I'm afraid it's critical if not officially certified "paperweight". Try uninstalling your PC's usb drivers for the device, or use another computer & install SUTL3 utility from Viewsonic, and see if it can at least beep & signal some USB sequence loading the drivers.
Here's a link to Droid Explorer posted elsewhere in XDA (instead of pointing you to "Search" for it) Install it if you can get the yours powered on, but use it with care as it's a very "powerful" tool to explore all the hidden workings of the Android device(s).
http://forum.xda-developers.com/showthread.php?t=558108
My feeling is that the core image & boot file(s) were corrupted, damaged & overwritten, and it need to be reformatted & reflashed from a stock *.nb0 file, someone with adb might be able to - maybe, just maybe - rescue it.
Let's see if one of our fellow developers might have a better solution on where to begin b/c this is about as far as I can offer - well, you can always put on eBay for parts & hoped you didn't spend a lot as 2nd. hand.
Uhhh looks like i have no other choice but to have this repaired at service center and pay
Hi,
i have some problems with mt HTC aria.
it was working fine, but not for my carrier, so i tried to unlock it.
after few tries the main touch-keys (home, menu, back, search) stopped responding.
i tried to hard reset and install everything all over again but somehow it crashed in the middle and now i can't do the hard reset again.
if i turn it on it shows me a white screen with these words (in green):
liberty pvt ship s-off
hboot-1.02.0000
microp-031b
touch panel-stn21_03
radio-7.16.35.11
nov 4 2010,23:12:58
RRU
i have no clue how to continue/restore.
can someone help me? pleeeeese!
nurief said:
Hi,
i have some problems with mt HTC aria.
it was working fine, but not for my carrier, so i tried to unlock it.
after few tries the main touch-keys (home, menu, back, search) stopped responding.
i tried to hard reset and install everything all over again but somehow it crashed in the middle and now i can't do the hard reset again.
if i turn it on it shows me a white screen with these words (in green):
liberty pvt ship s-off
hboot-1.02.0000
microp-031b
touch panel-stn21_03
radio-7.16.35.11
nov 4 2010,23:12:58
RRU
i have no clue how to continue/restore.
can someone help me? pleeeeese!
Click to expand...
Click to collapse
That's just the bootloader so you could try flashing a rom. Do you have a custom recovery installed?
Theonew said:
That's just the bootloader so you could try flashing a rom. Do you have a custom recovery installed?
Click to expand...
Click to collapse
hi,
i don't really know what or how.
can you instruct me step by step?
the thing is that i was trying to install this file : HTC_Aria_for_ATT_Android_2.2_ROM_Update.exe and in the middle of the process my USB cable disconnected, and the phone doesn't boot since.
it just show me a white screen with the text i wrote up there (and it's ruu, not rru, obviously) when i turn it on, and it doesn't go to the hard reset menu even if i hold the down-volume button when i press the power button.
nurief said:
hi,
i don't really know what or how.
can you instruct me step by step?
the thing is that i was trying to install this file : HTC_Aria_for_ATT_Android_2.2_ROM_Update.exe and in the middle of the process my USB cable disconnected, and the phone doesn't boot since.
it just show me a white screen with the text i wrote up there (and it's ruu, not rru, obviously) when i turn it on, and it doesn't go to the hard reset menu even if i hold the down-volume button when i press the power button.
Click to expand...
Click to collapse
You could just boot into fastboot (choose "fastboot" from the list in that menu) and re-run the RUU (Rom Update Utility).
nurief, you may need to pull out the battery to get out of the RUU screen. After putting the battery back in, hold down the trackpad button (that button below the screen) and press the power button, then release the trackpad button. It will say FASTBOOT if it worked correctly.
The RUU should be able to detect the phone while it's on the FASTBOOT screen.
drumist said:
nurief, you may need to pull out the battery to get out of the RUU screen. After putting the battery back in, hold down the trackpad button (that button below the screen) and press the power button, then release the trackpad button. It will say FASTBOOT if it worked correctly.
The RUU should be able to detect the phone while it's on the FASTBOOT screen.
Click to expand...
Click to collapse
do i need a certain files to be in the SD card?
i tried the trackpad boot, but i shows me a black screen with "HTC" in the center and four triangles with "!" in them at the four corners of the screen.
nurief said:
do i need a certain files to be in the SD card?
i tried the trackpad boot, but i shows me a black screen with "HTC" in the center and four triangles with "!" in them at the four corners of the screen.
Click to expand...
Click to collapse
Make sure you keep holding down the trackpad button until the screen turns on, then let go. Sorry, I should have been more clear about that.
If it still doesn't work, try the same process but this time hold down volume down button instead of the trackpad button. It should say HBOOT in blue near the top of the screen. Then after about 10 seconds, press power button once more. It should say FASTBOOT in red near the top now.
If either way works, then connect the USB cable to your computer then start up the RUU again and it should work fine.
drumist said:
Make sure you keep holding down the trackpad button until the screen turns on, then let go. Sorry, I should have been more clear about that.
If it still doesn't work, try the same process but this time hold down volume down button instead of the trackpad button. It should say HBOOT in blue near the top of the screen. Then after about 10 seconds, press power button once more. It should say FASTBOOT in red near the top now.
If either way works, then connect the USB cable to your computer then start up the RUU again and it should work fine.
Click to expand...
Click to collapse
it doesn't work.
i tried everything. turning on when the USB is plugged and unplugged, fastboot by holdin the trackpad and down-volume button...
when i plug the USB and unplug it the phone shows me the white screen with the text in to of this thread, and the "RUU" glows in orange background (like the fastboot) but i cannot choose the option even if i press the I/O button.
any ideas?
thanks.
Go to the IRC channel #liberatedAria on Freenode and ask if someone knows what to do. If no one is around, try again later.
If you don't know how to get on IRC, you can access it via web: http://webchat.freenode.net/?channels=#liberatedAria
Edit: From searching around online it seems like making a gold card might fix your problem.
drumist said:
Go to the IRC channel #liberatedAria on Freenode and ask if someone knows what to do. If no one is around, try again later.
If you don't know how to get on IRC, you can access it via web: [link] (the system doesn't let me send reply with links...)
Edit: From searching around online it seems like making a gold card might fix your problem.
Click to expand...
Click to collapse
thanks a lot, they helped me there to bring the device back to life.
but the old problem is still here.
the navigation touch keys (home, menu, back and search) doesn't respont to any human contact.
i figured out that if i touch the top of the screen - the backlight ot the keys turns on, but nothing more than that.
* the chat manager told me that he can't help me with that because they deal with rooted phones only, and i don't think mine is...
Any thoughts?
The ONLY area it seems to work is to power up the device.
I cannot do the following by pressing it or holding it...
1.) Wake device up
2.) Pull up the shutdown menu
3.) Hold down to power off device
...and most importantly...
4.) cannot select options in CWM (but if I hold volume and power it'll get me into CWM)
Any idea how to flash it back to stock? I have a jig if that helps. Thanks.
Currently the only way I can wake the phone is to plug into a charger.
This had happened to me like 3 times. What I did in order to get back to work, was opening the phone and blast some air with those cans of compressed air use for computers.
Nosferatu. said:
Any thoughts?
The ONLY area it seems to work is to power up the device.
I cannot do the following by pressing it or holding it...
1.) Wake device up
2.) Pull up the shutdown menu
3.) Hold down to power off device
...and most importantly...
4.) cannot select options in CWM (but if I hold volume and power it'll get me into CWM)
Any idea how to flash it back to stock? I have a jig if that helps. Thanks.
Currently the only way I can wake the phone is to plug into a charger.
Click to expand...
Click to collapse
Most likely the power button is going bad. I get these a lot. I can solder a new power button on for $50 including return shipping. You can email me @ seivad17 [at] msn.com
Electrical Cleaner
"Go to youtube and search how to dissemble, there are couple of video that shows a step by step process of dissembly. Now the only problem is that there isnt a specific video locating the lock button and you will have to find that yourself. So after you dissemble your phone, locate the lock and use CRC QD Electronic Cleaner I read that is the most reliable and decent one out of all sprays and all you need to do is spray around the button area, and push the lock button 20-30 times and repeat the process a couple of times. After that you should let it dry for a couple of min and then put your phone back together and it should work fine!."
This worked for me. I found it in the captivate forums. Been going 1 month strong after the cleaning!
adillar2 said:
"Go to youtube and search how to dissemble, there are couple of video that shows a step by step process of dissembly. Now the only problem is that there isnt a specific video locating the lock button and you will have to find that yourself. So after you dissemble your phone, locate the lock and use CRC QD Electronic Cleaner I read that is the most reliable and decent one out of all sprays and all you need to do is spray around the button area, and push the lock button 20-30 times and repeat the process a couple of times. After that you should let it dry for a couple of min and then put your phone back together and it should work fine!."
This worked for me. I found it in the captivate forums. Been going 1 month strong after the cleaning!
Click to expand...
Click to collapse
okay I'll check that out. How about the USB port? I need a solid connection to the computer. If that's the case I can jig it, place it in download mode, and re-install my ROM and get out of the boot loop I have the phone is in. The power button then is irrelevant because I'm sure I can set the phone to wake with the volume keys thus eliminating the need for the power button. That's the other issue (and more important issue). Otherwise, I have a paper weight.
Nosferatu. said:
okay I'll check that out. How about the USB port? I need a solid connection to the computer. If that's the case I can jig it, place it in download mode, and re-install my ROM and get out of the boot loop I have the phone is in. The power button then is irrelevant because I'm sure I can set the phone to wake with the volume keys thus eliminating the need for the power button. That's the other issue (and more important issue). Otherwise, I have a paper weight.
Click to expand...
Click to collapse
If you fix the power button and you can get into CWM (like your first post says) then you should have no problem. The power button is probably shorted out (like mine was) and you cannot use it for selection.
adillar2 said:
If you fix the power button and you can get into CWM (like your first post says) then you should have no problem. The power button is probably shorted out (like mine was) and you cannot use it for selection.
Click to expand...
Click to collapse
no I can no longer get into CWM
Short story I tried returning phone to stock and went to flash a stock image file via ODIN and it's stuck on the bootup screen.
Is there any software or commands I could use to diagnose my phone over USB? The screen is black, even during boot (no logos), but the phone is still working in the background. The notification LED blinks normally, menu and back button lights up when pressed, and it even rings when someone calls, though I can't see who it is b/c of the black screen. The screen is not cracked or damaged, and I didn't drop it, so not sure why this is happening. I want to test the GPU or other components before I put down a lot of money for a new screen and it no resolve the issue.
Phone is a rooted SM-N910V that has been working great for 3 months.
Thank you!
Modify_inc said:
Is there any software or commands I could use to diagnose my phone over USB? The screen is black, even during boot (no logos), but the phone is still working in the background. The notification LED blinks normally, menu and back button lights up when pressed, and it even rings when someone calls, though I can't see who it is b/c of the black screen. The screen is not cracked or damaged, and I didn't drop it, so not sure why this is happening. I want to test the GPU or other components before I put down a lot of money for a new screen and it no resolve the issue.
Phone is a rooted SM-N910V that has been working great for 3 months.
Thank you!
Click to expand...
Click to collapse
Hi , try with key kombination .
1. Make sure your phone is OFF
2.Now Press toghether Vol + and power button and hold like that until second vibration (reboot)
3. If that doesn't work try with another combination .
Vol - and Power button
Vol + & Home button & Power button for about 10 second
Vol - & Home button & Power button for about 10 second
Good Luck
Teddy Lo said:
Hi , try with key kombination .
1. Make sure your phone is OFF
2.Now Press toghether Vol + and power button and hold like that until second vibration (reboot)
3. If that doesn't work try with another combination .
Vol - and Power button
Vol + & Home button & Power button for about 10 second
Vol - & Home button & Power button for about 10 second
Good Luck
Click to expand...
Click to collapse
Thanks for the suggestions, though I have already tried all those plus other things.
I've left the battery out for over a day, removed sim card, held power button in to drain any residue power.
I'm lost as to why all of sudden the black screen. Hoping there's a way to test the phone to confirm if its the lcd or something else like the gpu chip. On a laptop you could plug a monitor in the vga port, don't guess phones have this option
Sent from my SAMSUNG-SGH-I337 using Tapatalk
Modify_inc said:
Thanks for the suggestions, though I have already tried all those plus other things.
I've left the battery out for over a day, removed sim card, held power button in to drain any residue power.
I'm lost as to why all of sudden the black screen. Hoping there's a way to test the phone to confirm if its the lcd or something else like the gpu chip. On a laptop you could plug a monitor in the vga port, don't guess phones have this option
Sent from my SAMSUNG-SGH-I337 using Tapatalk
Click to expand...
Click to collapse
I read that the phone was rooted so maybe that custom rom has some bug and that way you get black screen .
Try to flash him back to stock firmware and see if the problem is solved .
It is just rooted on the standard firmware, I didn't install any custom firmwares. But I was wondering if I could possibly reflash it from a backup I made with twrp. I cant get to recovery, well actually I could if I new the exact steps since everything works, I just cant see crap.
Is this even possible or is there another way to access twrp over the usb?
Sent from my [device_name] using XDA-Developers Legacy app