Related
I managed to upgrade my phone to aku 3.3 using pof's method(bootloader 1.01 MFG) . Then, out of no where, I tried to use MTTY to upgrade my radio rom
It started as usual with the status bar moving. Suddenly some error messages came up.
Now, the phone is dead completely. I can''t even enter bootloader mode.
Is there a possible way that I can still save it??
Help!!!!
Have I bricked my device? Help plz
I managed to upgrade my phone to aku 3.3 using pof's method(bootloader 1.01 MFG) . Then, out of no where, I tried to use MTTY to upgrade my radio rom
It started as usual with the status bar moving. Suddenly some error messages came up. Can't remember exactly, but like some address can't find error.
Now, the phone is dead completely. I can''t even enter bootloader mode. Only when I take out the battery and plug in the charger cable the red light comes on. I looked the upgrade problem page, my symptom doesn't match any.
Is there a possible way that I can still save it??
Help!!!!
I had something similiar happen a little while back. What I did was pull the battery out and leave it out for a while, maybe a few minutes. I then put the battery back in and held the two side buttons and hit the reset button to put me into bootloader mode. I then cabled it to my computer and flashed a new OS via mutty. That got my phone back and operational.
@float. Nuh, it didn't work on my brick. Prob i will have to take it back to Tmobile if they kind enough to repair the no warranty phone i bought on ebay.
Sorry to have opened a new thread, I was so desperate.
Plz delelte it.
how exactly did you try to update the radio using mtty?
I download the 1.27 shipped radio rom. P.S. It seemed to be a german version, not sure whether that caused the disaster.
Using NBHextract to get the single GSM.NB file, then in MTTY, typed
USB> task 32
USB> lnb GSM.NB
Before flashing, just had it upgraded to the HTC AKU3.3 OS rom only. The old version radio rom version before flashing was 1.18.
Maybe the order i flash is wrong. I flashed OS first then the radio rom.
just guessing
ok, you loaded the radio rom code where os.nb should go. That may have caused mega bad blocks in flash. Can you even get bootloader mode if you reset using Wiki directions to obtain Tri-color bootloader?
Yes. I have tried many ways wiki suggests. Such as removing the battery leaving it more than half an hour and plugging it to the usb cable without battery. still can't get to the tri-color bootloader mode. Basically, I just can't turn on the phone.
If you connect it to the computer, can it communicate w/the PC? If you hear the windows tones try opening up mtty and see if you can communicate.
i'm stuck in the same place
for me it happened during extrom flash
Try removing the battery for a bit (a few minutes, maybe half an hour). Then, put the battery back in but don't plug the usb cable in. After that, hold the two side buttons as if you're trying to get it to go into the bootloader. Hit the reset button a few times with your stylus and see if that gets you to the bootloader. That's what worked for me.
tried that
tried removing battery and connecting usb
nothing helps
is there a place that fixes tytn in belgium ?
is there a way to flash a new rom via mutty ?
cause i still have the boot loader, but the phone still in the splash screen
when i type info 2 in the mutty command prompt i get this answer
Cmd>info 2
HTCSQTEK_203”µ·êHTCE
i think it's not realy normal
diffda said:
is there a way to flash a new rom via mutty ?
cause i still have the boot loader, but the phone still in the splash screen
when i type info 2 in the mutty command prompt i get this answer
Cmd>info 2
HTCSQTEK_203”µ·êHTCE
i think it's not realy normal
Click to expand...
Click to collapse
well your not supercid... your still locked to qtek
Look here and unlock your phone before doing any flashing!
http://forum.xda-developers.com/showthread.php?t=295751
to late i ve done that tow day's ago , now the only way to make my phone back to life, PB + KITL method i think
god bless KITL
I was instaling NBD_v8.3_8MB trough shelltool on my MDA Vario then something happened and my PC restarted I whink it is because of the electicity .... so now when I restardet my phone it is stuck on the T-mobile screen Where it is writen.....
IPL 2.21.001
SPL 2.21.Olip
GSM 02.19.11
OS 6.6.6.666
Thanks in advance
First of all, its not bricked. Bricked = doesn't turn on, nothing, blank screen.
I've looked to your info, you already have HardSPL, so you can flash directly using any RUU, don't use shelltools!
Enter bootloader (hold camera+reset), open up the RUU of the ROM you want (make sure it doesn't have any IPL/SPL) and flash away
well I looked all day what to do and I can not find solution
I just can not understand how to flash the phone
I found one solution via some kind of Wizard_love, but again I do not know what to do
Please help i am haveing the same thing just did it today i have the Cingular 8125....i have held camera+reset and got into these Red,Green,Blue,white screen and it says IPL 2.25 and SPL 2.25 now when i run the ROMUpdateUtility_Wizard_NoID it does not work i have my usb pluged in and my phone says USB please help
Thank you
PS.
I am running Vista
IPL 2.25
SPL 2.25
GSM 02.25.11
OS.6.6.6.666
_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-
Ok i have try everything. I have tried the RUU from the HTC site and even everything else when it is searching for the PDA and crashes idk why. I turn on my phone holding the camera and i get to the Red,Green,Blue,White...Plug the USB in and the phone says USB but not my computer??? so i don't know what i need to do please HELP i just got the phone and read you can do all this stuff
1. Please use a PC with Windows XP
2. Download your original carrier ROM (i.e. Cinglular stock ROM) and flash back to original WM5
3. Install HardSPL or use SSPL
4. Flash to WM6
starkwong said:
1. Please use a PC with Windows XP
2. Download your original carrier ROM (i.e. Cinglular stock ROM) and flash back to original WM5
3. Install HardSPL or use SSPL
4. Flash to WM6
Click to expand...
Click to collapse
Were can i get HardSPL,SSPLand the flash back up?
all i have is the original rom
You guys wanna see bricked? I have a BRICKED! phone... My MDA was the unfortunate victim of a car accident. When my car went carreening off the road, my MDA went flying through the air and ended up on the floor of the car but not before hitting virtually every surface on the inside of the car.
Now my charge port is completely snapped off and my battery shorted out when I was trying to hold the charge port in place to charge it and fried the main board. DEAD. NO MORE.
THAT MY FRIENDS, IS BRICKED....
No worries though, I already ordered a TyTN II
Cool can you help?
Oh and i had the same problem with my mda and i got it replaced from tmobile. - the easiest way to reapair an MDA is getting it replaced ^^
offtopic
@dharvey4651
Why didn't you buckle up your phone?
Well i got mine up and running agian just used XP and install the RUU from HTC YES.......Now when i go to install WM6 when i press update were it should show me the Ver. of the one i am installing on my phone it does not say why please help and what do i need to install WM6 on my phone?
Just a quick question did you read the other threads there are already. They basicly explain everything clear and good
i have just still stuck on some stuff
dferreira said:
First of all, its not bricked. Bricked = doesn't turn on, nothing, blank screen.
I've looked to your info, you already have HardSPL, so you can flash directly using any RUU, don't use shelltools!
Enter bootloader (hold camera+reset), open up the RUU of the ROM you want (make sure it doesn't have any IPL/SPL) and flash away
Click to expand...
Click to collapse
jukata
first of all,as dferreira has assured u that ur device is not bricked,secondly ,you already have HardSPL,that means your device is unlocked,just follow his instructions,download any wm6 Rom and flash,it'll good to go,but if u still want to be sure,download WST Tool from the below given thread read carefully and apply the tool to verify the status of ur device,
http://forum.xda-developers.com/showthread.php?t=329170
u can flash NBD rom which u have or any other wm6 rom,goodluck
NVM i am on the Other Page! Thanks
Ok, i have read everywhere and can't help myself, so if someone would be kind enough to help it would be much appreciated
Ok, Used SoftSPL and tried flashing the ROM. It manages to get to 99% and then just goes RED. I have tried 3 different ROMS and same story it goes RED at 99%.
When i remove the battery, it goes to the RUU Red, Green and Blue screen. SPL version is 2.16.0001. Not Oli's new one.
What do i do from now?
kastro said:
Ok, i have read everywhere and can't help myself, so if someone would be kind enough to help it would be much appreciated
Ok, Used SoftSPL and tried flashing the ROM. It manages to get to 99% and then just goes RED. I have tried 3 different ROMS and same story it goes RED at 99%.
When i remove the battery, it goes to the RUU Red, Green and Blue screen. SPL version is 2.16.0001. Not Oli's new one.
What do i do from now?
Click to expand...
Click to collapse
Soft SPL only allows you ONE update, so phone is CID unlocked only when Soft SPL is loaded.
It's normal for the RUU to stick on 99 % for a couple of minutes, The whole update will take aprox 10 minutes.
You can try the hard SPL from there you are semi-permanently CID unlocked.
Good luck,
EquinoXe
i posted this in the other forum as it mite be more busy there http://forum.xda-developers.com/showthread.php?p=1703450#post1703450
i am new to all this and i stupidly went running into things and tryed to ROM upgrade my t-mobile Vario II (HERM300), not knowing i had to CID unlock first, it has broke! when i boot it up i can not get passed the t-mobile splash screen and it also flashes "no-gsm". i have read many suggestions on fixing this but i have had no luck. i can get into the boot screen however and get the red green and blue stripes. i have IPL 1.01 and SPL 1.04. it will allow me to connect to my PC with USB but active-sync does not recognize i have connected the phone.
please help someone. i just need a way i can get this thing working again. if i could just get the phone into a state of use again that would be good.
can someone help please.......??
Have you tried just flashing a Radio Rom Only?
I try to put AP DUAL 3.0 ROM on my AMEO with sim unlock.
Probably was CID locked, and so it was impossible to install this ROM, but here what happened....
When The Firmware Flasher rebooted the device at the first step when i pressed UPGRADE BUTTON my ATHENA died... no power at all..
I think at this passage the flashing process was not started at all, infact i did not see the tre coloured bar of the bootloader... IT DIED !!
It is impossible to power on, i try to plug the AC and no orange light...i i pull of the battery and insert the AC plug the red light is OK.....
What happens ?
Is there a way to recover my NEW DEVICE ?
Thanks to all the team !!!
gab74 said:
I try to put AP DUAL 3.0 ROM on my AMEO with sim unlock.
Probably was CID locked, and so it was impossible to install this ROM, but here what happened....
When The Firmware Flasher rebooted the device at the first step when i pressed UPGRADE BUTTON my ATHENA died... no power at all..
I think at this passage the flashing process was not started at all, infact i did not see the tre coloured bar of the bootloader... IT DIED !!
It is impossible to power on, i try to plug the AC and no orange light...i i pull of the battery and insert the AC plug the red light is OK.....
What happens ?
Is there a way to recover my NEW DEVICE ?
Thanks to all the team !!!
Click to expand...
Click to collapse
So did it start step 1 at all? Did u try a soft reset on the device to see if that would boot it back up?
Try running the unlocker anyway. You might be surprised
Olipro does excellent work. [tease]Or at least he didn't disappoint in the past![/tease]
See also http://forum.xda-developers.com/showthread.php?t=357142
See if you can get to the bootloader, what happened was that you used an older version and I'm assuming you got the x7501 which almost always is bricked when used with the older version of oli unlocker. I don't understand why they can't remove or re-label that old package, what's wrong with doing it???? Maybe less people would brick their device.
i've AMEO T-MOBILE X7500
The operating system was WINDOWS MOBILE 6
I did not use oil unlocker... i only try to flash with the ROM i say before, and my AMEO stops working before starting the flashing process.
Now my athena is died: without the battery i try to connect to ac cable and the red led lights up....when i insert the battery the red led lights off, i cannot enter into the bootloader because the ameo doesnt power on at all...
Please is there any solutions to this problem ??? It is very strange that the AMEO stop working ....before starting the flash process... infact when i push the UPGRADE button of the ROM flashing program, the ameo rebooted and died before starting the flashing process > i.e before the three coloured bars of the bootloader starts...
Any help : sorry for my bad english, i'm italian......
is there a way to power on ameo without battery ???
Just try oli's unlocker!
Sorry, but do i use the unlocker even if the PDA is died ? If i plug into the PC USB no hardware is found ? Does the unlocker work ? And please : Where can i download the last version of the unlocker ( probably a stupid question...)
yes, try the unlocker anyways. Download it from the http://forum.xda-developers.com/showthread.php?t=315831
Ok but the unlocker told me : Athena must be connceted with activesync...mine is died..only red led without battery or no led with battery inserted.....so i do not understand how the unlocker could work..... What unlocker do i download ???
In fact.. i try a nothing... the unlocker works only if the athena is recognized...so only if it is power up....but mine is dead only red led without battery....no led with battery instead...
It seems impossible that a simple flashing destroy the unit !!!!
Can you enter bootloader? Hold camera button while resetting
Or hard reset? Volume down wile poking the reset hole.
no, no bootloader, no hard reset...
nothing....
OK I contact HTC the told me to send the PDA to T-MOBILE CENTER to be repaired in warranty....but i leave in italy so i cannot send the pda in england...
i sell it on ebay is someone is interested...serach HTC ATHENA XT7500 AMEO T-MOBILE on ebay.co.uk.....
OK - I just had the same problem. No life whatsoever.
Simple solution:
Remove battery.
Wait one hour.
Replace battery.
All is fine
No need to send back to HTC
hello i´m from spain and I am new to the forum and I need help urgente.creo which is the best forum in which there pdas.the same that gab74.the pda is death or die.I do not know how I can rekindle my pda.Does nothing and htc have told me the same thing, besides not covered by the warranty.Help the PDA is new.
oscmae said:
hello i´m from spain and I am new to the forum and I need help urgente.creo which is the best forum in which there pdas.the same that gab74.the pda is death or die.I do not know how I can rekindle my pda.Does nothing and htc have told me the same thing, besides not covered by the warranty.Help the PDA is new.
Click to expand...
Click to collapse
I just told you the answer in my last post! Why do you have to ask again?
Hi all,
I got the same problem & I already did as Confucious's guide but it doesn't work. Any help?
Best regard,
Try my thread, I am having similar difficulties, though I know some solutions, so maybe some of your questions will be answered.. http://forum.xda-developers.com/showthread.php?t=528258
And in summary.. try jump-starting the battery, I'm almost sure it will help
Okay i have been going at this for 6 hours trying to figure this out.
I bought a HTC HD2 off of craigslist today for 200$ when the person gave me the phone to try it worked i played around with it and about 20 mins after i started messing with it ( the transaction had been made) it just shuts off. I go to turn it back on and it gets hung on the Stick Together screen after hard resets soft resets lukewarm resets.. every reset on the web nothing works i tried updating it nothing worked (from official firmware)
in the middle of all this it gets to a point where the stick together screen would be there for a split second going blank and the phone would vibrate 7 times.. no one knows what this means even HTC
i look online and people are saying install custom firmware sooo i downgrade from 2.10.0000 to 2.08.0000 and install a custom firmwar Kumar v4.1 touch premium with thier recomended Radio file.. i do this about 3 times.. now instead of "Stuck together" its stuck on the custom flash splash screen.
i tried the task 29 and doing it all over again and im still stuck
HOW DO I FIX THIS? did i just spend $200 on a peice of $#!7 paper weight?
any advice would be helpful.. though "search the thread noob" wont be applicable to me .. i searched it for a few hours to no avail.
if i missed the page please direct me to it instead of being snide about it chewing me out for spam post wont help me fix my problem
Set your device into Bootloader
- turn off device
- press and hold volume down button
- pres shortly on the power button
- you will see now a 4 color screen = bootloader
=> can you communicate us the values you see on your bootloader screen.
And just a question, witch Radio did you install?
PB81120 SS-B3
SPL-2.08HSPL 8G XE
0x05
Cotullahspl 0x50
as for the radio:
Radio Leo 2.15.50.14
therian12 said:
PB81120 SS-B3
SPL-2.08HSPL 8G XE
0x05
Cotullahspl 0x50
as for the radio:
Radio Leo 2.15.50.14
Click to expand...
Click to collapse
I don't see direct reasons of problems based on this information.
Maybe a suggestion is to install a newer stock rom.
that was the first thing i tried when i first got the phone, when that didnt fix it i resorted to installing custom firmware.. right after i went on the forum and posetd i installed artemis custom fw and left the battery out over night and when i woke up i put the battery back in and it worked perfectly.. well almost.. it booted up none of the programs would work no camera no game nothing it always said either program wasnt set up or there wasnt enough memory on the phone. so i turned it off ( huge mistake) and put the most recent stock firmware on it after reverting the HSPL back into the SPL 2.08.0000 and its stuck on the stick together screen again
Can you get it into BootLoader Mode, as I suspect that the SPL is still 3.03.0000
You cannot use HSPL3 when you have a 3.03.0000 SPL on the phone.
What stock ROM are you trying to flash?
T-Mobile_HD2_MR_Software_3.14.531.1
thats the name of the file i downloaded to do it .. i reinstalled the stock SPL and tried upgrading it to the file ^^^^ left the battery out for 30 mins plugged it all in , it booted does alot of stuff but when i touch the camera button it froze shut down and locked me out again at the Stuck together screen.
im willing to donate 30$ to whoever can help me fix this
i have more info about the crashes and whatnot
today i have been keeping a record of how long the phone is on for and what im doing when it crashes and wont reboot without keepign the battery out for 15+ minutes
turning vibration on for ringer was only on for 5 mins
using the camera not even taking a picture just looking through the lense on for about 15 mins
trying to send a text message on for about 10 mins
just now had one whil just letting it sit there after 15 mins
i have still been browsing the forums for solutions im thinking it could be the radio file im using that futzing up so ima try that
also .. WTF does MTTY actualy mean .. is it a more formatting formatting utility .. or.. what?
Okay so i updated the radio to Leo_RADIO_2.15.50.14
and now when i turn on the phone it vibrates 7 times with no image
if i leave the battery out for 15+ minutes it boots up just fine till i start to actualy use it. i can play a video listen to a song but i turn off data and then turn on wifi and it locked up on me, only way to get it to turn back on is to pull the battery and let it sit for 15+ minutes again.
soo no one has any idea on whats going on wrong here?
sorry for posting so many times.. i just am without phone and it sucks
try to install artemis rom again with sspl
sspl thats stock spl right?
my phone is at 2.10.0000
therian12 said:
sspl thats stock spl right?
my phone is at 2.10.0000
Click to expand...
Click to collapse
no sorry install latest stock rom thn you should have spl3.03.00
after that you shoul be able to flash artemis with sspl becouse you cant flash on 3.03.00 thats why we use sspl if you dont have it i can sent it to you
i just install stock SPL package from tmobile's website when i enter boot loader it says my SPL version is still
SPL-2.10.0000 8g XE
therian12 said:
i just install stock SPL package from tmobile's website when i enter boot loader it says my SPL version is still
SPL-2.10.0000 8g XE
Click to expand...
Click to collapse
try to flash spl1.42 with hspl3pkg and bthen try to flash artemis rom
how do i do that?
well all this trouble for nothing... after installing the Energy rom i wanted to try and install the stock rom again , converted the HSPL 2.08 back to stock went to put the phone back in bootloader mode and its a brick...
try to contact this member maybe he can help you
you should contact the member of this forum by the name of trashcan... he is the only person in the united states that has the jtag device used to re program the hd2