The power button on my TYTN II is playing up. It gets stuck down sometimes so I need to replace it. Does anyone know where I can get spare parts from in the UK?
You might get a better response in the TYTN2 forums:
http://forum.xda-developers.com/forumdisplay.php?f=376
Related
:?: i finally wanted to use my siemens sx56 after a year... Now it doesn't want to start all the way up... Lots of problems.. Battery light will not come on... No start bar on screen... Resets itself all the time... blinking backlight about every 15 seconds... etc... Please help me... I just want to use it again... it has wallaby bootloader 5.15... ppc 2002 3.14..
Have you tried a hard reset, that is using the unscrewed top half of the stlylus in the hole on bottom right of xda, leave for one minute then press again.
I recently picked up an SX-56 that was long unused. It took a few minutes on the power before the lights would come on. Plug it in and let it juice for a minute, and then a cold boot is definately in order. Also, make sure that the SIM door is fully closed.
thanks for reply guys... But i tried all of that stuff... sometimes it will bring up windows but there is no start button... also i can't even use a stylus because it's not tuned up.... also it won't let me connect to activesync... comp see's it but cannot connect...
i think u need a new one
Can you get to the bootloader?
First - sincere thanks - great site - I unlocked my XDA months ago with no problems
On holiday, number 1 son dropped it on a rock. :evil: Power button only works if held down. Initially would give normal today screen. Now only gives wallaby bootloader screen v5.15. Same on cradle and activesync no longer recognises the device.
From bootloader screen I can acess the diagnostics screen but when I run tests it gets stuck at the playback test.
Not suprisingly resetting using the stylus doesn't help either.
Will I have to bin it and start again?
I no gadget lover but I really love this piece of kit, so if any of you can help I will be sincerely grateful.
Darth Dopey
Did you do a hard reset by unscrewing stylus and inserting in the hole below headset socket, push once, leave for a while then push once more?
Hard Reset
Hi
Using the stylus only works if I am pressing the power button. It results in the Wallaby bootloader screen going off and then coming back on.
Is this a hardware problem - ie phone+rock = broken power switch
or
This is now a hardware and software problem?
Darth Dopey
Hi, i thougt my phone was hurricane after checking the pic out on main forum, but i guess i was wrong as i jsut found that it is actually htc tornado.
I was following the instructions here :
http://forum.xda-developers.com/showthread.php?t=330709&page=20
and after performing step 7
7. Downloaded http://rapidshare.com/files/58201559/Lazaj007.zip and patched my SPL (extract and start patched_RUU.exe)
my phone turne off after 100% installation and i cant get it back on!
i tried to goto boot loader but all in vein.
Tried holding camera button and putting usb cable noth9ing. tried holding camera and communication button and pressing power on button, nothing. any help or time to trash it away?
i think that you broke bootloader. if it is only white screen (nothing else) or doesn't want to switch on, give them to service.
what do u mean by service?
like right now it just wont turn on. just as if the battery is dead but my battery was fully charged when i did the process.....
where can i give it for service? thanks for your help.
ps. By the way its a brand new sda too never used it
It's bricked. There's no (practical) way to fix it other than to replace the motherboard.
If it's under warranty, then try to get it replaced. If not, time to sell it on eBay for parts or you can PM me if you want to sell it for cheap because mine could use a new housing and keypad.
Before anyone jumps on me, I've been going through the Wiki and forums extensively, and found just one similar problem. Which wasn't solved...
My HTC TyTN/Hermes 200 won't boot up anymore. It is totally dead. I even can't get it into bootloader mode. Screen stays blank and the LED is off.
Put the (3 months old) battery in another Hermes to test it, and it's at 100% charge.
My Hermes shows a steady red LED when it's plugged into power without the battery in, and no LED at all when the battery is installed. The red LED turns off when the battery is installed while there's power going into the unit.
I've left the battery out for at least an hour, plugged it back in, same results. Like the other guy I tried the "pull power, pull battery, plug in power, plug in battery, reset" trick http://forum.xda-developers.com/showthread.php?t=286469&p=1077622 - to no avail.
Does anyone have any last resort ideas on how to get it to at least come back up to a boot loader screen ?
Help Me Too
Hi siliconaddict,
I have the same problem!
I received an SMS, slid open the keyboard and there...DEAD!
I also flipped through the forums for a long time, extensive googling but
to no avail!
H E L P !
No revival unfortunately
FREIMAURER said:
Hi siliconaddict, I have the same problem!
Click to expand...
Click to collapse
In the past few days I have received some email messages with well-meant tips and tricks , which I already had tried myself. Nothing worked however ... The damn thing is totally dead .
I have obtained another (2nd hand) Hermes 200 in the meantime, in perfect condition and at a fair price, so I am back in the Hermes business again.
I will use the old one for parts, should I ever need them.
Sorry I could not help.
MfG
I am waiting for my Treo 750 without camera to arrive from USA which I ordered
in wise foresight.
I will probably buy a used Hermes with broken display and switch the boards and
use that one as replacement.
Thanks anyways...but what I find strange is that so many Tytns die at the same
time and this more often for the Tytn II generation.
Have a nice weekend!
Cheers
Hi,
My Samsung Tbalet 10.1 GT7500 with Android 4.0 suddenly froze with the Samsung logo at boot and then became dead. Not starting or charging.
I have searched for help and done the following -
1.Pressing the power button long enough
2.Pressing power and volume together and similar permutations
3.Pressing volume up and down and touching the screen
4.Connecting to a car charger and connecting to a PC
5. Opened the back cover and disconnected the connector from the battery for 3 minutes and tried to charge again
I cannot even do a hard reset by pressing buttons since there's no response to any button!
Can anyone help? I don't mind even a hard rest just to get it going or any other clever ideas.
A bit desperate as cannot replace this tablet for some months!
Megan
Can only see apx on the device manager!
After spending a day with it, the tablet is still dead but when i connect to the pc and press power, I can view apx in the device manager?!!
Can any one in XDA help at all?!