Ok so I just performed a Task29 which was successful, and as I went to flash a new ROM I got a message saying check USB is connected to PC and Phone.It doesn't seem to be connecting.When I enter Bootloader "serial" shows up at the bottom but not "USB" How can I check my USB is causing the problem?The other problem this creates is that I cant now use my phone!
Related
Hi! I tryed te fash my niki 200 with original rom! The flash is stopes to 42% and now i have boot mode with this message "Upgrade ROM code error! Please try again". I can not conect again to usb because i received message :"usb device not recognized". Mtty can not conect because i received the same message! There is another metod de make this device?
Have you flashed HardSPL?
Put your device into bootloader (hold b oth Camera and Power button while performing a Softreset via Stylus) and now you can theoretically flash your Provider ROM!
After that your device will work again!
I have not flashed hardspl! If i put the Niki in boot mode, show only "serial" on the screen with usb cable pluged and PC says "usb device not recocnized"!
Flashing in bootloader mode doesn't requires an ActiveSync connection so ignore it and start the ROM Upgrade! It's working, believe me! I've flashed my Niki with this method hundred of times!
I tryed to flash my niki in bootmood, but not working "error 260:conection"! My computer not recocnized my device (with or without activesync)!!!In bootmode on screen show "serial" and when i pluged the cable nothing happend (must see on screen:USB)! This is my problem!!! The computer does not alocate to my device a com port(USB). The same problem with MTTY (no USB poet detected). You understand me?
Maybe your USB drivers screwed up.
Trie with an other PC, this helped me one time.
I tryed on other computer with Xp and other with Vista! The same problem! Not recocnized!!!!!!!!!!!!!!!!!
bugytech said:
I tryed on other computer with Xp and other with Vista! The same problem! Not recocnized!!!!!!!!!!!!!!!!!
Click to expand...
Click to collapse
I've got the same issue. Did you resolve this? I would like to find a solution
From a noobie:
Question 1: My original problem is on soft reset my HTC xv6800 hangs at tricolor with "Serial" at the bottom of screen unless the usb cable is plugged in. It will boot to wm6.1 if I plug in the usb cable at soft reset. Then I get no USB connections in WM61, and my PC does not detect the phone at all at the usb port. I'm stuck with inability to do any sync on the phone.
I am hoping if I install a newer radio ROM it might fix the hang at tricolor with Serial, and usb connection problem. Is this reasonable or do these symptoms indicate something more grave?
Can you recommend any next steps?
Have you tried relocking the phone and flashing back to stock rom? Once you have it back to stock, see if it boots normal. If it does, go thru the steps flashing it back to custom and see if the problem comes back.
BTC
Since I've had the same stock OS ROM and verizon authorized radio ROM for several months, I assumed the ROMs were not the problem. The problem just began last week or so. What I have done is installed neuSPL2.47 wnd reflashed radio ROM and flashed TitanReloaded1.3.2.
I've checked the cable using a different device and it gets recognized by WinXP. I am now syncing with Activesync in bluetooth, and I've flashed both the OS and radio ROMs... With these steps above, is it apparent or feasible that I have a hardware usb issue on the phone?
The only issues I have are that I cannot power up the phone without a usb cable in the phone - it goes to bootloader without the cable plugged in, and I must sync via bluetooth, which is not a huge issue unless I really want to use usb for connection to PC.
Do you still think the ROMs could be the culprit?
Any ideas on why it would go to bootloader with "Serial" at the bottom unless an active usb cables is plugged in? Does anuyone know what the "Serial" message means?
What happens if you plug in the USB cable after the bootloader comes up, does it change to USB or does it keep saying serial.
It does sound like maybe your USB port is bad, if you get it booted up normally, does it see activesync in windows, does your headset work, etc?
Basically, if you use the cable trick to get it to boot, does the USB port seem completely normal then?
BTC
Flash it using your microsd
BillThyCat said:
What happens if you plug in the USB cable after the bootloader comes up, does it change to USB or does it keep saying serial.
It does sound like maybe your USB port is bad, if you get it booted up normally, does it see activesync in windows, does your headset work, etc?
Basically, if you use the cable trick to get it to boot, does the USB port seem completely normal then?
BTC
Click to expand...
Click to collapse
The port seems dead after bootup, once it gets past the bootloader. It never says USB in the bootloader. Should I see that if USB is confirmed functional? What does "Serial" mean? Activesync does not see the Titan whatsoever when using USB connection after it boots. I sometimes get an error popup at the taskbar in WinXP Pro that says the usb device has a problem...
HI !
I have an HD² with official Operator's ROM and my HD² never sync with my computer.
I want to know if it's possible to Flash everything without any sync (only by SD)?
Thanks a lot for my LEO
settings menu all settings connections connections usb to pc, untick "faster data". restart the pc, restart the phone.
it should now sync fine.
Thanks for the Answer, but I've already do this and the results is the same.
Sorry about my English cause I'm French
Go into Bootloader Mode (hold Volume button down while switching on the phone). You will get a tri colour screen with the word 'Serial' at the bottom of it. Plug in the USB calbe and it should change to 'USB'. If this happens then you can run HSPL and then ROMs - just ignore the conditions about making an ActiveSync connection prior to running.
I've already try this
But not exactly how you say.
I've plug the in the USB calbe when the HD2 was Off, and after loading the bootloader.
And nothing was happen.
Juste the 3 colors and the SPL version but never "USB" or "Serials", serial appears only if I don't plug the cable.
Load it into Bootloader Mode, then connect the USB cable - and see if the 'Serial' changes to 'USB'. If it doesn't, then you have a hardware problem (phone or cable or computer).
I think it's a Phone probleme.
Cause I've a Samsung wave and I havn't any problem with the same cable and the same computer.
Also I can't flash my HD²...
Sph1nxXx said:
I think it's a Phone probleme.
Cause I've a Samsung wave and I havn't any problem with the same cable and the same computer.
Also I can't flash my HD²...
Click to expand...
Click to collapse
got another pc to try? what windows you using? stock usb cable? tried all your different usb ports? remembering to right click and "run as administrator"? no usb hub? if its 64bit windows, definately try a different pc.
samsamuel said:
got another pc to try? what windows you using? stock usb cable? tried all your different usb ports? remembering to right click and "run as administrator"? no usb hub? if its 64bit windows, definately try a different pc.
Click to expand...
Click to collapse
I've already Try on another computer.
I've try with my seven OS, and with XP OS.
The problem is the same.
But when I plug the USB cable, the computer says "unknown Device" and it's the same on different computer with different cable...
I think my HD2 mother card is probably broke for this.
Hi everyone.
So I have a Motorola Droid RAZR XT910 its on 4.0.4 OTA with no root.
The issue I have is that I connect the phone to my PC via USB cable and it does not pick it up.
A few things you must know is:
•I have windows 7 32-bit and
•I am using the cable that comes with my phone
What happens when I plug my phone is the computer says installing drivers for unknown device and then it claims to have successfully installing them for "unknown device". My phone does give me option to chose what type of connection I want but it does charge.
Things I have tried:
•A different cable
•A different PC
• Re-installing drivers
• Re-installing Motocast
•Trying with USB Debugging enabled and disabled
•Different USB ports
•Factory reset
•Different USB ports
•Tried installing PIM Sync form Google Play Store
So yeah that's my problem any help will be helpful...
Try the drivers here:
http://www.motorola.com/consumers/v...59431210VgnVCM1000008406b00aRCRD&pubid=987654
When you try another cable, make sure that works with another device, and not just for charging.
The below instructions will help you troubleshoot if there is a problem with the usb connector on your phone.
1.Power off and disconnect usb cable.
2.Press and hold vol up and down, then hold the power button.
3.You should come to a boot mode selection menu.
4.Press vol down twice to highlight AP fastboot, press vol up once to select.
5.You should see AP fastboot flash mode (s), with last 2 lines saying "Connect USB, Data Cable"
6.Connect your USB cable to your PC and phone, and see if it says USB connected.
7. If nothing happens then it's probably a hardware problem, get it repaired.
Nikorasu said:
Try the drivers here:
http://www.motorola.com/consumers/v...59431210VgnVCM1000008406b00aRCRD&pubid=987654
When you try another cable, make sure that works with another device, and not just for charging.
The below instructions will help you troubleshoot if there is a problem with the usb connector on your phone.
1.Power off and disconnect usb cable.
2.Press and hold vol up and down, then hold the power button.
3.You should come to a boot mode selection menu.
4.Press vol down twice to highlight AP fastboot, press vol up once to select.
5.You should see AP fastboot flash mode (s), with last 2 lines saying "Connect USB, Data Cable"
6.Connect your USB cable to your PC and phone, and see if it says USB connected.
7. If nothing happens then it's probably a hardware problem, get it repaired.
Click to expand...
Click to collapse
Hi thank you for your help.
So I did this method on my PC and it was unsuccessful but i tried it on my mothers and it worked!
So I will update the drivers on my mothers PC and see If I can successfully connect to her PC and use USB mass storage for the first time since I've had Ice Cream Sandwich!
I will keep you updated
Its definitely software. Ill have to wait till there's a rooting application that doesn't require a connection between a PC and phone. One rooted I can flash a ROM from there on...
On your mother's PC, it worked in AP fastboot right? As in the words "USB connected" appears on your phone.
From there you can flash a rom.
Nikorasu said:
On your mother's PC, it worked in AP fastboot right? As in the words "USB connected" appears on your phone.
From there you can flash a rom.
Click to expand...
Click to collapse
I can flash fastboot files which I dont want to do.. I want to flash custom ROMs which require root.
The ap fastboot worked for me but when i restarted the phone it still wont connect with mass storage. i do not own a motorola usb cable mine is an LG and i dont really have money to buy one. bought the phone on ebay and it did not ship with one so ive been using this. it only connects as charging.
Hi,
maybe one of the experts can help...
I have a LEMAX2 with X820_20S_ROW_CUOCO92 ROM.
Since half a year or so the USB-Connection to the PC does not work anymore. Tried several cables and several PCs, no change.
I can boot the phone in RECOVRY Mode, but it It shuts itself off immediately.
I can enter fastboot mode, but the phone is still not recognized by the PC.
When I connect the phone via MyPhoneExplorerClient, WLAN works, but MyPhoneExplorerClient says 'USB-Cabel 'Not conneced.'
When I unplug and re-plug the USB-Cable, for a short time MyPhoneExplorerClient says 'USB-Cabel 'conneced', but no setting option for USB configuration can be found and after a second or so MyPhoneExplorerClient shows 'USB-Cabel Not conneced' again.
I tried to find out how to change or repair the firmware but all howtos require a USB Connection.
Mayby I accidentaly removed some system software responsible for the USB Connection?
Any idea?
:crying:TWSMS