Hi every one:
I did the upgrade yesterday for my qtek but the upgrade is for O2 so i found that the startup screen is for the O2, is any one know how to change the startup screen????
The startup screen is fixed in the ROM. So you're not able to change it.
Only possibilities are to cook your own rom in your own ROMkitchen or stay at the qtek software...
Regards
Stefan
So you got the nice QWERTY device eh? Nike Hard-SPL gives you a Model ID error? well, that'll be because you have a Neon.
Now, I've finally done a fully working Neon Hard-SPL, so, have at it as you desire:
instructions:
1)have device *SYNCED WITH PC, NOT IN SODDING BOOTLOADER*
2)run RomUpdateUtility
3)pay attention to device when loading bar appears on PC; say YES to any prompts and when it goes into SPL, UNPLUG AND REPLUG YOUR USB CABLE
after that it'll take care of itself
Has anyone tested this out yet??
im stuck with this...help
Hello
I don't flash my niki with hard-spl v2
When i flash i have a error message id model
When i modify model in nbh neon to niki i have message error file corrupted
Help me please
this is for NEON, do not flash it to your Nike, use the Nike Hard-SPL.
Olipro said:
this is for NEON, do not flash it to your Nike, use the Nike Hard-SPL.
Click to expand...
Click to collapse
Ok thank's
updated, works fully for all NEON devices
hey.. ok iv done this... now can you run me thru step by step on how to re-flash my device with a standard NEON ROM ??? i downloaded the original ROM but still dont allow to re-flash my branded device
nice job oli. time for some more beer i guess
BUFFBOY said:
hey.. ok iv done this... now can you run me thru step by step on how to re-flash my device with a standard NEON ROM ??? i downloaded the original ROM but still dont allow to re-flash my branded device
Click to expand...
Click to collapse
sure, shall I wipe your arse for you too?
Before i patch this in a NEON, can i flash with Niki Firmware???
thank u oli
Thanks
Quick & Easy... thanks
Thanks... This worked beautifully.
Ummm, OK I just tried this on my NEON300 Touch Dual US version and now my screen is stuck in Tri-Color mode:
RUUNBH
NEON300
SPL-0.95.0000
CPLD-3
USB
Is there a way for me to get back to my standard Windows Mobile screen setup?
bignerd972 said:
Ummm, OK I just tried this on my NEON300 Touch Dual US version and now my screen is stuck in Tri-Color mode:
RUUNBH
NEON300
SPL-0.95.0000
CPLD-3
USB
Is there a way for me to get back to my standard Windows Mobile screen setup?
Click to expand...
Click to collapse
Did you unplug the USB for 10 seconds then replug? Part of the recovery stage is taking out the battery, getting back to your original startup
bignerd972 said:
Ummm, OK I just tried this on my NEON300 Touch Dual US version and now my screen is stuck in Tri-Color mode:
RUUNBH
NEON300
SPL-0.95.0000
CPLD-3
USB
Is there a way for me to get back to my standard Windows Mobile screen setup?
Click to expand...
Click to collapse
"set 16 0" in mtty.
however, if you manage to get back to the OS... I'd like to see this 0.95 SPL
Hi there,
got the unlock code for a neon and when restart with the different sim card it asks for the unlock code but actual unlock button is disabled. any ideas how to fix this problem?
thanks
niki or neon?
Hi,
i use your 3 step to unlock my dual touch.....
it was 1.16 and now is 1.15.....
everything going well till step 3 where i get error 240.........
and now i see that all qwerty device are neon !!!!
i use the neon update rom but now it gives me error 260 after confirming yes 2 times on screen.....it dont whant to update.......
is it because i use Motorola usb cable ???
thanks for helping
Rectification not neon but niki 100
hi,
After verification the dual touch is niki 100....on back of batery and inside the phone..................
still not want to do step 3 error 240.....
Best regards
hi
i have niki 100 bricked
i use mtty boot command it start to boot and hang on splash screen
i tryed every thing task 9 set 14 0 set 16 0
can any onbe help me
b/r
hacker1gsm said:
hi
i have niki 100 bricked
i use mtty boot command it start to boot and hang on splash screen
i tryed every thing task 9 set 14 0 set 16 0
can any onbe help me
b/r
Click to expand...
Click to collapse
What exactly did you do to your device ? Have you tried to flash a ROM without hardSPL ? Have you flashed a bad Radio ?
We need details to help you.
hi
i Have tried to flash a ROM without hardSPL
now the phone in boot mode (tri color)
and with mtty with command boot it boot but hang on splash screen so i cant copy the sspl file cause the phone not detected on activsync
b/r
Whats about trying to flash a original ROM from your provider?
Maybe it may help. After that first do a hardSPL! befor flash another ROM
You also can try to flash from SD-Card... take a look <<here>>
the problem that my phone orginal rom it TIM italy i cant find rom for it all i have is dump and dump need unlock spl to flash it
b/r
I have big problem with my Niki.
I was using nemanjalo ROM ver.23007 and have no problem with that.
When I found SuDream ROM here I get big problem. ROM is very unstable and slow, and every time my device soft reset its back to screen calibration (hard reset).
So I decide to back to nemanjalo rom 23007 lite version, but problem still happend. after first time calibration, auto install some program and soft reset its back to screen calibration again.
and every time i make a softreset it's back to screen calibration and some program like resco explorer, SPB won't install.
My question is :
1. what wrong with my niki ?
2. is that possible a cooked rom break internal memory/ROM chip ?
help me please....
my niki was hardspl 1.22
Delete in windows/startmenu/autostart/ the file Welcome...
this solve the problem with the screen calibration.
i don't think that a cooked rom can break the internal memory, i think something goes wrong while flashing, try to flash again should help.
I've brick my MDA Vario II. I think the only way to unbrick is the PB-KITL-method. I've installed the MS Windows CE 5.0 Evaluation installer and create like these description (http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES a new rom.
Now I have to set the MDA in the KITL-mode. But I can't do this. There are a lot of different description but I cannot set the MDA in the KITL-Mode.
so I need your help.
bienchenmeier
Maybe this: http://wiki.xda-developers.com/index.php?pagename=Hermes_Resets ?
I've read this before. When I press COMM and Power-button start reset, the MDA boots. I see the t-mobile start screen (I always press the both button) at the bottom of the screen I see in red letters:
M05
S04
B06 D1.21
after a few second No GSM
an the the screen changes to Windows mobile start screen an then the screen frozen
bienchenmeier
Hi You all,
Well here is my question to you,
I have an HTC Touch DUAL NIKI100 SPL-1.16.0000
CPLD-4
1.58.16.27
25.61.30.03h
I have bought the cell in France but live in belgium. He was as you know simlocked. Now i try'ed to unlock him with the tutorials given here in this forum
And have to say it is a very poor tutorial. Doens't understand what to do at all?
I have unlocked a lot of cell's .. Most of the time Iphone, I Homebrew and chips a lot of gaming consoles (Wii, PS2, Xbox) so i have to tell i know what i am doing, but this tut made my hair stand up because i really cannot folow during the poor tut.
Now i have payed to unlock my cell and now it works.
But here is my other question... How can i set this phone into the dutch language?
When i do this steps :
1. download the attached files - OK
2. REMOVE SIM and SD CARDS !! - OK
3. connect usb cable - OK
4. copy sspl-1.16-nike.exe to your device and run it (usb cable must be connected!) - OK
5. after a few seconds "USB" appears on the display - Stays at Loading
Click to expand...
Click to collapse
and then i am stuck.
Then i try'ed to just skip 4 and 5 an go further .. But then when i am :
8. you can now flash the hardspl-1.15mfg-nike.nbh by running ROMUpdateUtility.exe from flash-uspl-niki : tells me to go from 1.58.16.27 to 1.00.00.00 (or something like that)
9. after installing the hardspl you can flash any rom (rom cook project here)
It is very anoying ! Can someone give me a BETER explenation how to resolve my problems ..
Sorry for the bad english, but as you could see i am from belgium
Kind regards and hopefully till i get a good explenation.
Peter
Weird. it will show loading if the microSD is still in the slot. remove cable when u see USB after running SSPL & reconnect cable > flash HardSPL.
at step no 8, just ignore the version numbers.