So you got the nice QWERTY device eh? Nike Hard-SPL gives you a Model ID error? well, that'll be because you have a Neon.
Now, I've finally done a fully working Neon Hard-SPL, so, have at it as you desire:
instructions:
1)have device *SYNCED WITH PC, NOT IN SODDING BOOTLOADER*
2)run RomUpdateUtility
3)pay attention to device when loading bar appears on PC; say YES to any prompts and when it goes into SPL, UNPLUG AND REPLUG YOUR USB CABLE
after that it'll take care of itself
Has anyone tested this out yet??
im stuck with this...help
Hello
I don't flash my niki with hard-spl v2
When i flash i have a error message id model
When i modify model in nbh neon to niki i have message error file corrupted
Help me please
this is for NEON, do not flash it to your Nike, use the Nike Hard-SPL.
Olipro said:
this is for NEON, do not flash it to your Nike, use the Nike Hard-SPL.
Click to expand...
Click to collapse
Ok thank's
updated, works fully for all NEON devices
hey.. ok iv done this... now can you run me thru step by step on how to re-flash my device with a standard NEON ROM ??? i downloaded the original ROM but still dont allow to re-flash my branded device
nice job oli. time for some more beer i guess
BUFFBOY said:
hey.. ok iv done this... now can you run me thru step by step on how to re-flash my device with a standard NEON ROM ??? i downloaded the original ROM but still dont allow to re-flash my branded device
Click to expand...
Click to collapse
sure, shall I wipe your arse for you too?
Before i patch this in a NEON, can i flash with Niki Firmware???
thank u oli
Thanks
Quick & Easy... thanks
Thanks... This worked beautifully.
Ummm, OK I just tried this on my NEON300 Touch Dual US version and now my screen is stuck in Tri-Color mode:
RUUNBH
NEON300
SPL-0.95.0000
CPLD-3
USB
Is there a way for me to get back to my standard Windows Mobile screen setup?
bignerd972 said:
Ummm, OK I just tried this on my NEON300 Touch Dual US version and now my screen is stuck in Tri-Color mode:
RUUNBH
NEON300
SPL-0.95.0000
CPLD-3
USB
Is there a way for me to get back to my standard Windows Mobile screen setup?
Click to expand...
Click to collapse
Did you unplug the USB for 10 seconds then replug? Part of the recovery stage is taking out the battery, getting back to your original startup
bignerd972 said:
Ummm, OK I just tried this on my NEON300 Touch Dual US version and now my screen is stuck in Tri-Color mode:
RUUNBH
NEON300
SPL-0.95.0000
CPLD-3
USB
Is there a way for me to get back to my standard Windows Mobile screen setup?
Click to expand...
Click to collapse
"set 16 0" in mtty.
however, if you manage to get back to the OS... I'd like to see this 0.95 SPL
Hi there,
got the unlock code for a neon and when restart with the different sim card it asks for the unlock code but actual unlock button is disabled. any ideas how to fix this problem?
thanks
niki or neon?
Hi,
i use your 3 step to unlock my dual touch.....
it was 1.16 and now is 1.15.....
everything going well till step 3 where i get error 240.........
and now i see that all qwerty device are neon !!!!
i use the neon update rom but now it gives me error 260 after confirming yes 2 times on screen.....it dont whant to update.......
is it because i use Motorola usb cable ???
thanks for helping
Rectification not neon but niki 100
hi,
After verification the dual touch is niki 100....on back of batery and inside the phone..................
still not want to do step 3 error 240.....
Best regards
Related
Hi does anyone know if there are WM6 ROMs for the SPV C550 if not are there any good WM5 ones?
look topic about wm5 for hurricane, there are also links to wm6 for hurricane device
hello again
here is latest, almost perfect rom for hurricane:
http://rapidshare.com/files/56833250/566.zip.html
and new SPL for this device:
http://rapidshare.com/files/56616745/spl566wm6_spfans2006.rar
lazaj007 said:
hello again
here is latest, almost perfect rom for hurricane:
http://rapidshare.com/files/56833250/566.zip.html
and new SPL for this device:
http://rapidshare.com/files/56616745/spl566wm6_spfans2006.rar
Click to expand...
Click to collapse
Has anybody tried this ROM?
lazaj007 said:
hello again
here is latest, almost perfect rom for hurricane:
http://rapidshare.com/files/56833250/566.zip.html
and new SPL for this device:
http://rapidshare.com/files/56616745/spl566wm6_spfans2006.rar
Click to expand...
Click to collapse
Ideal thanks
So is the 566.zip the WM5 or WM6 rom and has it been tested?
Whats the new SPL?
hI ALL, can u tell me the mini guide how to install this rom? I did it once to my sda but I dont remember now, where is the nbfupdatetool and RUU and patched RUU..???
when I type l c:\wm6.bin it give me this:
clean up the image temp buffer at 0x8C080000 Length 0x01B00000 MTTYDownloadImageNot allow operation!
Error : DownloadImage return error (code = 0xFFFFFFFF)
cmd>
maybe damaged rom, or any idea?
Gang: Make sure you're CID unlocked. (Eg, when you issue "info 2", it says HTCSuperCID).
How can do that cid unlock? give me some working link to download that tool or something. thx
here you go
http//www.spv-developers.com/content/SPV-Services.zip
you must check "CID Tool (Alpha)" and click set CID=11111111
after this restart your phone
and short solutions about wm6 installing:
* installation is the same like typhoon
-unlock Super CID
-upgrade new SPL (Patched ruu)
-disable USB connection in ActiveSync
-switch off your phone
-press and hold camera button, and put USB cable to your phone
-next check "Y"
-when your phone will be in bootloader mode (tri color screen) run mtty
- check USB connection in this program
and write: - info 2
- format BINFS
- l c:\566.bin (localization of your rom)
after succeful installising reboot your phone and it will be end
rom is very good, baterry work better
hmm, thx for guide, I believe it will work, but I have little problem : now I cant even connect to activesync so I cant do cid unlock, any idea how to fix that
lazaj007 said:
here you go
http//www.spv-developers.com/content/SPV-Services.zip
you must check "CID Tool (Alpha)" and click set CID=11111111
after this restart your phone
and short solutions about wm6 installing:
* installation is the same like typhoon
-unlock Super CID
-upgrade new SPL (Patched ruu)
-disable USB connection in ActiveSync
-switch off your phone
-press and hold camera button, and put USB cable to your phone
-next check "Y"
-when your phone will be in bootloader mode (tri color screen) run mtty
- check USB connection in this program
and write: - info 2
- format BINFS
- l c:\566.bin (localization of your rom)
after succeful installising reboot your phone and it will be end
rom is very good, baterry work better
Click to expand...
Click to collapse
Thanks for helping out!
A few questions?
1. This link "http//www.spv-developers.com/content/SPV-Services.zip" takes me to Wikipedia.
2. Where can I find the patched ruu to update the spl. It wasn't in the zip file?
Thanks in advance!
to Mr MIAGY :
1. just write that link starting with www. (without http//, or type http://)
2. in ''wm6 for c550'' topic u will find patched RUU and all needed files, they are ziped together
gangstaunitg said:
to Mr MIAGY :
1. just write that link starting with www. (without http//, or type http://)
2. in ''wm6 for c550'' topic u will find patched RUU and all needed files, they are ziped together
Click to expand...
Click to collapse
DoH! I didn't notice the missing ":"
Cheers!
Anybody have idea why I cant connect to activesync after spl upgrade ? Before spl upgrade it all goes well. Can I do something with it?
if upgrade was complited succes then you must turn off USB connection in Active sync, then run bootloder mode and do everything with instructions.
I did it !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
THank u all, thankS
This rom is amazing, everything work perfect, and it looks beautiful,
one more time thank you. jUUHHHUUUUUUUUU
lazaj007 said:
if upgrade was complited succes then you must turn off USB connection in Active sync, then run bootloder mode and do everything with instructions.
Click to expand...
Click to collapse
Upgrade reported as success
However after reboot I see the WM6 boot screen - loverly ...
Then the Mobile Operator Splash screen ... THEN
After too long ... the phone switches itself off and I have to take the battery out to get reponse again.
Any ideas?
It's a C550 ....
MrMiyagi said:
Upgrade reported as success
However after reboot I see the WM6 boot screen - loverly ...
Then the Mobile Operator Splash screen ... THEN
After too long ... the phone switches itself off and I have to take the battery out to get reponse again.
Any ideas?
It's a C550 ....
Click to expand...
Click to collapse
Ok, so a report. The phone boots, goes through WM6 splash screen, then operator screen, then APPARENTLY dead black screen.
BUT I plugged in the USB cable and the screen came on! WM6 Setup screen! All good go through setup eveything looks GREAT!
Only problem is, if I leave the phone alone for a bout a minute, the screen goes black AGAIN. Then no amount of key pressing on the device will bring it back to life.
Plugging the USB cable in brings it instantly back to life! But This means I can't wander too far from my PC ;-)
ANY Ideas
BTW IT LOOKS FANTASTIC! If I can just get around this issue ;-)
MrMiyagi said:
Ok, so a report. The phone boots, goes through WM6 splash screen, then operator screen, then APPARENTLY dead black screen.
BUT I plugged in the USB cable and the screen came on! WM6 Setup screen! All good go through setup eveything looks GREAT!
Only problem is, if I leave the phone alone for a bout a minute, the screen goes black AGAIN. Then no amount of key pressing on the device will bring it back to life.
Plugging the USB cable in brings it instantly back to life! But This means I can't wander too far from my PC ;-)
ANY Ideas
BTW IT LOOKS FANTASTIC! If I can just get around this issue ;-)
Click to expand...
Click to collapse
Heh heh ... seems I'm posting to myself ... that's cool I like my own company ... So I reflashed the SPL and some of the problems have gone away.
Phone will boot OK now ... but it will still "go to blank screen" and require plugging into the USB cable to "wake it up"
I'm out of ideas now ...
Hello together,
I got a T-Mobile MDA Vario II upgraded to Windows Mobile 6 and like to use thisone with a Vodafone SIM.
Here some Data about:
(Info from the Bootloader)
HERM300
IPL-1.04
HERM300
SPL-2.03
Systeminformation:
ROM-Version: 3.60.111.4
Radio-Version: 1.50.00.00
I've tried to Downgrade to WM5. I've tried button_rom.
I've tried everything, i have found about Down / Upgrade, about Sim-Unlock etc. etc. etc. ....
But i'm to Stupid to Sim-Unlock this MDA.
Always when I try to Downgrade to WM5, the Setup starts normally.
After the MDA enters the Bootloader the Setup will show an error like "no device....".
What did I wrong?
Please help me :-|
Thank You All!
PS: Sorry for my bad english..i hope, you understand me
tbler said:
Hello together,
I got a T-Mobile MDA Vario II upgraded to Windows Mobile 6 and like to use thisone with a Vodafone SIM.
Here some Data about:
(Info from the Bootloader)
HERM300
IPL-1.04
HERM300
SPL-2.03
Systeminformation:
ROM-Version: 3.60.111.4
Radio-Version: 1.50.00.00
I've tried to Downgrade to WM5. I've tried button_rom.
I've tried everything, i have found about Down / Upgrade, about Sim-Unlock etc. etc. etc. ....
But i'm to Stupid to Sim-Unlock this MDA.
Always when I try to Downgrade to WM5, the Setup starts normally.
After the MDA enters the Bootloader the Setup will show an error like "no device....".
What did I wrong?
Please help me :-|
Thank You All!
PS: Sorry for my bad english..i hope, you understand me
Click to expand...
Click to collapse
I think the RomUpgradeUt.exe that exists in the wm5 ROMs is not compatible with SPL 2.03.
try this:
Extract the .nbh file from your desired wm5 rom (Rename your ROM from *.exe to *.zip and extract it using winzip).
Flash it to your device using RUUwrapper.exe (Force using SSPL).
:,-(
Hey together again,
now i've made the update.
It shows no error or something other.
The MDA looks like a WM5 device - But it will stop booting when it shows the first WM5-Picture.
Ok...now it will stop when it shows the "T-Mobile" Splash Screen..
Well....one Softreset later .... i have a white Screen
This i have already done:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
The SPL is 2.03 again.....
Now I can't go on with the RUUWrapper ......
Is there any posibility to Update the MDA while staying in the Bootloader (works without problems).
Thank You Again
Greetings from Germany
http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing
Hello Again,
i've tried to perform the update this way.....but it won't work :-(
I insert the SD-Card, load the Bootloader, after this, the Display show's:
"Loading...."
After this:
"Checking..."
And for a Short time
"00028002
Not Allowed"
Then I'm in the RGB-Colored Bootloader......
Any Idea? I've tried the WM6-File from the T-Mobile Page, the WM5-File....
No of them will work.
Thanks again!!!!
Have a look through this...
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=41&Itemid=27
might be of use, havent had a change to read it fully so it might not be any help.
tbler said:
Hello Again,
i've tried to perform the update this way.....but it won't work :-(
I insert the SD-Card, load the Bootloader, after this, the Display show's:
"Loading...."
After this:
"Checking..."
And for a Short time
"00028002
Not Allowed"
Then I'm in the RGB-Colored Bootloader......
Any Idea? I've tried the WM6-File from the T-Mobile Page, the WM5-File....
No of them will work.
Thanks again!!!!
Click to expand...
Click to collapse
I don't understand your situation exactly??
Do u have wm6 on your device now?
Can ur device boot into os or not?
Do u have NO GSM error?
Hello,
i've read the manual.
But it won't help me.
The Autor wrote this:
"Connect the device up to activesync using the USB cable, then run RUUWrapper.exe"
My Problem: Windows Mobile 5 or 6 doesn't Boot - So i can't use the RUUWrapper....
To enter the "special" BootLoader I need an working WM5 or WM6....
Do you know, what I mean? My english isn't the best.. sorry :-/
@koorosh_bsboys
- I DON'T have the "NO GSM" Error.
- My OS does not Work.
- The device looks like it's a Windows Mobile 5 (i can't see more, because it doesn't boot | It will stay at the blue Screen ("Windows Mobile" and the Windows Logo)).
- Update per SD-Card brings the following Situation:
I insert the SD-Card, load the Bootloader, after this, the Display show's:
"Loading...."
After this:
"Checking..."
And for a Short time
"00028002
Not Allowed"
Then I'm in the RGB-Colored Bootloader......
please exactly tell us your problem
1.IPL version?
2.SPL version?
3.Can boot into OS?
3.KITL enabled or not? (hold Power+comm manager+left ok buttons and reset with stylus, keep touching them until you see the KITL dialogue - if enabled-)?
4.NO GSM error?(when restarting ur device look out to bottom of the screen, do you see NO GSM)
koorosh_bsboys said:
please exactly tell us your problem
1.IPL version?
Click to expand...
Click to collapse
=> IPL-1.01
koorosh_bsboys said:
2.SPL version?
Click to expand...
Click to collapse
=> SPL-2.03
koorosh_bsboys said:
3.Can boot into OS?
Click to expand...
Click to collapse
=> NO (So i can't run the SSPL)
koorosh_bsboys said:
3.KITL enabled or not? (hold Power+comm manager+left ok buttons and reset with stylus, keep touching them until you see the KITL dialogue - if enabled-)?
Click to expand...
Click to collapse
=> I hold the Buttons for about 1 minute....but i will stay in the 3-Colored-Bootloader - So I think - Not Enabled
koorosh_bsboys said:
4.NO GSM error?(when restarting ur device look out to bottom of the screen, do you see NO GSM)
Click to expand...
Click to collapse
=> Yes, now i've seen the "NO GSM" Error....(http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5 <= Method 2 I've tried...but won't help!)
I know....i made something wrong..but i don't know what :-(
Sorry to tell you that dude!
But welcome to the club of bricked hermeses with spl 2.03.
Until now there is no known sulotion to fix that, unless you want to send ur device to service center!
OK...that's very ****, but i can't change this.. *damn* :-(
I have one more MDA Vario II with WM6, SPL2.03 and IPL 1.01
=> WORKING....
But i think i'll unlock this one by the "T-Mobile-Sim-Unlock-Code".
I won't risk the second mda ;-)
THANK YOU VERY MUCH!
Why Flashing...?
Go to any vodafone store..make your device back to WM6..
say to the guy @ vodafone store that your going on a holiday.. they will give you a key that unlocks the device..
and your done ! ! ! Works for a friend of mine
ElProempie said:
Why Flashing...?
Go to any vodafone store..make your device back to WM6..
say to the guy @ vodafone store that your going on a holiday.. they will give you a key that unlocks the device..
and your done ! ! ! Works for a friend of mine
Click to expand...
Click to collapse
I don't think, that a vodafone store will give me a unlock-code for a t-mobile device.... :O
And the next Problem is, that de MDA doesn't boot the OS and have the "no gsm" error....
anyone know what rom is compatible with athe100 SPL 1.10 ?
i know theirs lots of 1.2 and 3.5 spl roms, i tryed to flash a 3.5spl on my phone and now only way i can turn on the phone is in bootloader, i try to flash the phone but it always gets stuck at 1%, can anyone assist me?
cowballz69 said:
anyone know what rom is compatible with athe100 SPL 1.10 ?
i know theirs lots of 1.2 and 3.5 spl roms, i tryed to flash a 3.5spl on my phone and now only way i can turn on the phone is in bootloader, i try to flash the phone but it always gets stuck at 1%, can anyone assist me?
Click to expand...
Click to collapse
Have you took the sim card and memory card out?????
Jay
yes they are both out when tryign to flash, been over a week with out a working athena
cowballz69 said:
yes they are both out when tryign to flash, been over a week with out a working athena
Click to expand...
Click to collapse
try flashing your original ROM which should be found in the wiki section.
ignore what I said below and report back if you were able to load your original ROM
***Ignore this read above**Once your phone is working , do the athena wrapper which should load SPL 1.2
Also read this
http://forum.xda-developers.com/showthread.php?t=429013
yes I tryed to flash the original rom (its a wm5 i beleive to), still gets error after 1%,, downloaded both on the wiki and the ftp site, =\ been over a week so far no clues on why i cant flash, i even tryed to change the mac address using mtty, but instead of going into level = 0 , i get level = FF witch means the phone is locked out from flashing anything threw mtty,
thank u guys so much for responding on my issue
I also tryed doing the unlocker and its a no go
If the error when it stops at 1% is "invalid model id" the solution is here http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
cowballz69 said:
yes I tryed to flash the original rom (its a wm5 i beleive to), still gets error after 1%,, downloaded both on the wiki and the ftp site, =\ been over a week so far no clues on why i cant flash, i even tryed to change the mac address using mtty, but instead of going into level = 0 , i get level = FF witch means the phone is locked out from flashing anything threw mtty,
thank u guys so much for responding on my issue
I also tryed doing the unlocker and its a no go
Click to expand...
Click to collapse
I think this means your phone is not unlocked
with respect to sergiopi , you cant do the mtty script.
I would suggest you msg cmonex or try to talk to her on IRC on the
dxa-devs channel
addendum
seeing that you have nothing to lose, why dont you try flashing the original rom from the sd card using the method in the wiki
cowballz69 said:
anyone know what rom is compatible with athe100 SPL 1.10 ?
i know theirs lots of 1.2 and 3.5 spl roms, i tryed to flash a 3.5spl on my phone and now only way i can turn on the phone is in bootloader, i try to flash the phone but it always gets stuck at 1%, can anyone assist me?
Click to expand...
Click to collapse
I have the same problem.
what I do...
I have ameo t-mobile...windows mobile 5.0
run AthenaUnlocker
Step 1 make all finish noc problem
Step 2 hung up on 60 %
bootloader no problem....but can´t flash original flash always stuck at 1% and reboot...
flashing the original rom from the sd card using the method in the wiki ...
make it, but no do...on screen see
cheking...
loading....
than come on screen
0002802
ching...
loading...
not allowed
sergiopi said:
If the error when it stops at 1% is "invalid model id" the solution is here http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
Click to expand...
Click to collapse
My error when it stops at 1% is "invalid vender id"
my image version is demaged
Re: Ameo from t-Mobile german - repair
________________________________________
hi
what is your CID? use mtty command "info 2" to find out.
for example, if it is TMOB_007, you have to find a shipped athena rom with that CID.
if you cannot find a matching rom, let me know, i can still help,
cmonex
HTCS Þ?ÒtHTCE
please need halp
thx
felix999
read this post http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
read this post which tells you how to run mtty
follow the instructions to start mtty then press enter to get the cmd prompt
then type info 2 to get your CID
depending on this you will be able to flash the apprpriate ROM
lakeman said:
read this post which tells you how to run mtty
follow the instructions to start mtty then press enter to get the cmd prompt
then type info 2 to get your CID
depending on this you will be able to flash the apprpriate ROM
Click to expand...
Click to collapse
in mtty this can read:
when type task 32
become LEVEL: FF
when type info 2:
HTCS Þ?ÒtHTCE
my CID is 1.1
on bootscreen can see this:
ATHE100
IPL-v1.00
ATHE100
SPL-v1.10.RP00
what I do before...
Ameo WM 5.0 >>>>my mistake not update to WM6.0
run AthenaUnlocker
STEP1>>>OK
STEP2>>>by 60 % hang and stopped....
and now have the big problems.....Image ROM of t-Mobile 5.0 german demaged
can´t flash any rom´s
thx for hel or I want to pay bucks for service, when ma ameo live again...
felix999
lakeman said:
read this post which tells you how to run mtty
follow the instructions to start mtty then press enter to get the cmd prompt
then type info 2 to get your CID
depending on this you will be able to flash the apprpriate ROM
Click to expand...
Click to collapse
this is my CID
Cmd>info 2
info 2
Wait interpreter timeout
HTCS Þ?ÒtHTCE
????????
don´t know
felix999
Athena mobile 6 > SPL 1.10
become today a answer from crazy cat, that olipro say must take an rom in athena forum....
I flaswh with so many roms...anytime same error: error 294 - invalid vendor ID.....
My SPL 1.10 >>> can´t find a rom with SPL 1.10
what rom can repair my demaged ameo?????
thx for help
felix999
problem solved with ONLINEHELP from>>>>>cmonex>>>><<:::::>><<:::E:::>><<:::R:::>><<:::F:::>><<:::E:::>><<:::C:::>><<:::T:::>>
thx
felix999
lakeman said:
try flashing your original ROM which should be found in the wiki section.
Click to expand...
Click to collapse
Is this how you solved your problem?
Hi everyone, I need help please. I am trying to flash a WM 6.5 ROM to my NIKI 100 (20 keys) but I cant seem to find a HardSPL that will work on my phone I always end up getting "ERROR[262]" I followed the steps to flash sspl-1.16-NIKE.exe on my phone in order to flash a HardSPL but still the same problem.
I have Official 2.09.405.1 ROM, Radio - 1.65.28.25. If I go into bootloader mode it shows: NIKI 100
SPL-1.22.0000
CPLD-4.
Is there anyone that can tell me wich HardSPL I need?? So far I"ve tried -
flash-HardSPL-Niki, HardSPL-1.15mfg-Nike, HardSPL-1.16.Nike, HardSPL-1.22-Nike-shipped and Flash-uspl-Niki.
Thanks
I hope this help
1. installed the SSPL installatoin, v1.16 (look at this thread http://forum.xda-developers.com/showthread.php?t=355730 for the installation)
you can skip step 7 and above.
2. Still in Bootloader screen, you can install HardSPL 1.22 using the installation files.
Dont worry about the step that device must connected to activesync just check the status and do next to update ROM. As long as your device is in bootloader mode (rainbow color) the update process can continue even you are not connected to activesync
3. Good luck
Has this been solved?
Heya Cyanide..
Has this problem been solved? If not, I reckon you should check this out: http://forum.xda-developers.com/showthread.php?t=377260
I have both the 16 keys and 20 keys versions of the HTC Touch Dual. And the confusing thing is, the 20 key version is not a Nike. It is actually a Neon 200 (or at least mine is). How do you tell?
Remove the back cover of the phone, and remove your battery... The label will reveal whether it is in fact a Nike or a Neon. If it's a Neon, then that explains why your attempts to Hard-SPL haven't worked to date.
Anyways, hit up that link above, and you should be able to Hard-SPL easily. If you need directions, let me know, but it should be fine... let us know how you go
HK 20key version is NIKI100
Hi dr3wster
Just FYI. In HK 20 keys version of the Touch DUAL says NIKI100 inside the battery compartment.
to be honest I'm confused over NIKI, NIKE, NEON now, but will keep reading.
dr3wster said:
Heya Cyanide..
Has this problem been solved? If not, I reckon you should check this out: http://forum.xda-developers.com/showthread.php?t=377260
I have both the 16 keys and 20 keys versions of the HTC Touch Dual. And the confusing thing is, the 20 key version is not a Nike. It is actually a Neon 200 (or at least mine is). How do you tell?
Remove the back cover of the phone, and remove your battery... The label will reveal whether it is in fact a Nike or a Neon. If it's a Neon, then that explains why your attempts to Hard-SPL haven't worked to date.
Anyways, hit up that link above, and you should be able to Hard-SPL easily. If you need directions, let me know, but it should be fine... let us know how you go
Click to expand...
Click to collapse
With wich OS you PC (not your HTC) is working?
The error message sounds to me like you are working with VISTA.
If so, try to do these steps on a XP system, and it should work.
Hi,
I made sure...underneath the battery it says NIKI 100.
I tried alot of hard spl's and nothing works.
MvSt said:
With wich OS you PC (not your HTC) is working?
The error message sounds to me like you are working with VISTA.
If so, try to do these steps on a XP system, and it should work.
Click to expand...
Click to collapse
I am working with XP and not Vista
me too have same problem with niki100
i have also same probelm under battrey writen niki100 i tried alot of things here
but not working .
i need a help to flash my niki100 to english
thanks
clickes2000 said:
i have also same probelm under battrey writen niki100 i tried alot of things here
but not working .
i need a help to flash my niki100 to english
thanks
Click to expand...
Click to collapse
Try it this way.
Greetz,
Im having problems on installing wm 6.5 roms on my htc touch dual running on 6.1. Whenever i try to run sspl-1.16-nike.exe it just goes black and the word usb never comes up. Anybody know how to fix this. thanks in adance
coolcar65 said:
Im having problems on installing wm 6.5 roms on my htc touch dual running on 6.1. Whenever i try to run sspl-1.16-nike.exe it just goes black and the word usb never comes up. Anybody know how to fix this. thanks in adance
Click to expand...
Click to collapse
Ok, let's try to help you, can you tell me what you did exactly, because you need to remove your simcard and sdcard, after that you can run sspl-1.16-nike.exe from your device, not your computer.
If you did all that, turn your device off and press the on/off button and the camera button on the same time if 'm correct it will bring you in a four coloured screen, can you give me the info from that screen.
Greetz,
My phone doesent have a sim card so i just skipped that step.
Hi coolcar65, can you tell me what see in your bootloader, you can come in the bootloader by turning the phone off and press the on/off button and the camera button on the same time.
I also need to know if your device have a simlock.
Greetz,
it says
neon400 mfg
spl-0.27. cnvrsa
microP-NeonC (led) v4
coolcar65 said:
it says
neon400 mfg
spl-0.27. cnvrsa
microP-NeonC (led) v4
Click to expand...
Click to collapse
Ok, that's why you can not run the sspl 1.16 because the sspl 1.16 is for the Nike and not the Neon, they look the same but they are completly different from the inside.
You have to read this post that one is for the neon400.
Succes coolcar65
Thank you so much!