Related
Hello.
I have a problem I hope someone here can help me to solve..
I have an Orange SPV M3100 that hangs on the Windows Mobile screen when I try to start it.
I'm able to go into bootloader mode, and i have tried using mtty142.exe with the set 14 0 command. It still won't boot. I've also tried to hard reset it.. still won't boot..
What I did was trying to unluck the SIM-lock with the Universal unlocker (HTC_Uni_Unlock_v1) from buzz. At the time I thought universal meant that it worked on all HTC devices (stupid, I know)... And I also thought it was harmless to just try and see if it worked. But I got an error around 92-93% and after that my device won't start. So my radio ROM might be screwed.
I'd like to flash my ROM with the i-mate one (JASJAM_WWE_1.20.305.3_1.20.305.104_1.07.03.10_ship.exe) and then add the ext-rom. But how do I do that when I can just access the bootloader screen? And do you think it will boot again if I'm able to flash it?
Here's some more info about my device:
HERM100
IPL-1.01
SPL-1.04
Thank you very much in advance. Help will be highly appreciated.
No your rom *is* screwed. You can get into bootloader, you can even get to 11% of a dopod etc rom upgrade if you try, but you will not flash a new radio.
You CAN boot the device.
Do a hard reset, but do not press spacebar to reboot after. Instead, do a soft reset. The unit should boot but as you've screwed the radio you will not get a gsm signal and the phone will say unknown sim status.
I know this as I bought one cheap after the owner had done exactly the same as you.
IMEI-check's unlock solution is the only one that works IIRC, and in some cases this re-writes the security area of the phone and repairs similar issues, but in this case I could not get the prog to read.
You need to return the device to HTC - you'll need to pay approx £35 for reflashing back to the orange rom. This is what I had to do.
Currently you cannot book the m3100 in through the web as it's too new, instead email / call them.
http://service.htceurope.com/
edit - or if you're an orange customer ring 150 and act dumb saying it ' won't work'.... :wink:
Richard
What happens if you just leave the phone in bootloader mode and then try to flash any ROM (imate, dopod, htc...)? run 2 times the RomUpgradeUt.exe if you get an error on the 1st try.
If you get an error while running the rom upgrade utility you can monitor the USB port while upgrading (you will see the real error from the bootloader then), there's some more info on this wiki page:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
good luck
pof said:
What happens if you just leave the phone in bootloader mode and then try to flash any ROM (imate, dopod, htc...)? run 2 times the RomUpgradeUt.exe if you get an error on the 1st try.
If you get an error while running the rom upgrade utility you can monitor the USB port while upgrading (you will see the real error from the bootloader then), there's some more info on this wiki page:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
good luck
Click to expand...
Click to collapse
No, if you want to send it back under warranty do not try to run a rom update as there are no orange rom packages. As described in my post above, it will get to 11% and stop. The device will be in the same state as before, with the same ext rom, but the splash screen and bootloader will have changed.
i.e: it will be bloomin obvious you tried flashing it and failed. Not what you want if you try for a warranty repair....
There is no error from the bootloader - as there is no radio rom present and no security area the upgrade process just hangs.
Richard
fluffcat1 said:
No, if you want to send it back under warranty do not try to run a rom update as there are no orange rom packages.
[...]
i.e: it will be bloomin obvious you tried flashing it and failed. Not what you want if you try for a warranty repair....
Click to expand...
Click to collapse
That's true, do not try to flash any other roms if you want to use the warranty or send the device back...
Thank you very very much for your help guys.
As I'm the administrator of these devices in the company I work for I just grabbed a new SPV and will send this thing back to Orange. It sounded like I'm getting a new one..
Well, I think I've learnt my lession.
Oh, and I have another question. Is there a reg editor I can install on this one so I can remove the app lock? I know I can install java apps, but it's a bit grumpy about apps that needs installation (the developer must be certificated).
Cheers guys.
Hi,
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
The rom must match your CID. Let us know if it works
pof said:
Hi,
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
The rom must match your CID. Let us know if it works
Click to expand...
Click to collapse
Errr, did you read the last post? He sent it back......
Richard
I just wanted to let him know there's a possible solution, it just in case he still has the unit
pof said:
I just wanted to let him know there's a possible solution, it just in case he still has the unit
Click to expand...
Click to collapse
Maybe his search is broken as well as his old phone eh?.... :roll:
fluffcat1 said:
You need to return the device to HTC - you'll need to pay approx £35 for reflashing back to the orange rom. This is what I had to do.
Click to expand...
Click to collapse
Sorry to take the thread a bit OT, but just wanted to confirm this again.
So, if I flashed my M3100 with a different ROM, and then had to return the phone to Orange for repair for a different reason, I can send it back to HTC just to have the ROM reflashed, and then send the phone to Orange to get the repairs done?
I've been hesitating on whether to flash the phone with a non-Orange ROM because I didn't want to give up the ability to obtain warranty repair (as there is no ROM upgrade yet). If it's just a matter of £35 and then everything else as normal, maybe it's not so bad...
Thanks!
My SPV M3100 won't start!!!
I also did this, so if anyone can find a solution it would be greatly appreciated.
Also tried this and it didn't work for me:
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
"I have a problem I hope someone here can help me to solve..
I have an Orange SPV M3100 that hangs on the Windows Mobile screen when I try to start it.
I'm able to go into bootloader mode, and i have tried using mtty142.exe with the set 14 0 command. It still won't boot. I've also tried to hard reset it.. still won't boot..
What I did was trying to unluck the SIM-lock with the Universal unlocker (HTC_Uni_Unlock_v1) from buzz. At the time I thought universal meant that it worked on all HTC devices (stupid, I know)... "
rachelm700 said:
I also did this, so if anyone can find a solution it would be greatly appreciated.
Also tried this and it didn't work for me:
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
"I have a problem I hope someone here can help me to solve..
I have an Orange SPV M3100 that hangs on the Windows Mobile screen when I try to start it.
I'm able to go into bootloader mode, and i have tried using mtty142.exe with the set 14 0 command. It still won't boot. I've also tried to hard reset it.. still won't boot..
What I did was trying to unluck the SIM-lock with the Universal unlocker (HTC_Uni_Unlock_v1) from buzz. At the time I thought universal meant that it worked on all HTC devices (stupid, I know)... "
Click to expand...
Click to collapse
the above link doesnt work?
zohaer21 said:
the above link doesnt work?
Click to expand...
Click to collapse
IIRC it is this link on the new forum:
http://forum.xda-developers.com/showthread.php?t=277281
spv m3100 don't start
hello guys
I have the same problem about spv m3100. I used "universal unlock tool" to unlock my device and now it don't start,don't boot...I tried the Hermes SD Card flashing methods with qtek001 rom and, a white screen with "loading...." appears for 2 second and then nothing else appened. I think that the method is right but I need to use a different software. what do you think about?
please help me
thankksssss
My SPV M3100 won't start
SD card method is no good as there is no upgrade from Orange until January.
Tried to do a radio upgrade explained here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
But it didn't work just came up with connection error, tried to monitor USB but nothing showed up to find out why, althouth mtty commands always do show up in USB Monitor.
Still have a brick and looking for a solution, hopefully, someday, please someone help me I am loosing my mind.
Hello
How to enter boot mode on HTC 200 ?
My htc hangs on HTC screen.
I'm trying to reflash it.
Thanx
Chris
@chrisro, Please read the wiki:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
http://wiki.xda-developers.com/index.php?pagename=Hermes_Resets
Thank you very much.
Greets form Poland !
Chris
Hi,
I did the popular mistake, tried to unlock with Universal Unlocker , thinking that this is the staff to unlock all the HTC phones.
Ok. What I have now:
NO GSM - we know that
Tried to install radio roms from here, nothing. I got the information about "Checking the information...." and it is hanging like this.
I made reser and HARD RESET aswell.
I tried to install a lot. Nothing helped.
I had radio ver. 1.05.... I remember that. I have my phone from T-Mobile from UK. I had everything nice, now I have four stripes - RED GREEN BLUE and WHITE and ther is written:
HERM300
IPL-1.01
HERM300
SPL-1.04
Can anybody help me ? I tried to download mtty.exe and put all the commands (not PASTE and it still not working.
Now is 6am in Lisbon. I was sitting all that night and I am finishing writting this post.
Help if you can, regards.
Ben
Have a look on this topic http://forum.xda-developers.com/showthread.php?t=280733
It did not help. Where I can get this Qtek rom ? Is that OK for my device ? I have VARIO II from T-Mobile.
I woul like to try instal this - DUMPED English ROM from TMobile Vario II from here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_DumpedRoms
but i dont now how. There are 3 .raw files, how to put them to my phone ?
That solution didnt help: http://forum.xda-developers.com/showthread.php?t=280733
What else I can do ? I was trying with QTEK rom and a got white screen on the phone and 0% on the computer. It was hanging. I tried 5 times. Then I tried to install the Radio Rom from here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
I choosed all of them. Nothing. All of them are hanging on:
Chencking the information on your device... Please wait..
Then there is a screen to update. After long time. So when I press the button is still the same info. Checking the information on your device... Please wait..
And its hanging. When I reset to bootloader again the soft telling me:
This ROM Upgrade Utility does not design for your device.
Please get probper ROM Upgrade Utility and try again!
Where can I get the radio version 1.05 for T-Mobile Vario II ???????????
Is there possibility to download from somewhere ?
Or maybe I should try other solution ?
Read "problem 5" here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
Yes, I was tying point 5 few times. The problem is, I can connect through mtty.exe without any problems, but after soft reset, I am pressing POWER and OK button and going to bootloader mode again, and when I am trying to flash the extracted radio ROM (i tried all of them = 4) and there is a problem. nothing is working. I am waiting and waiting, and there is only info: Checking your device information or something like that. What can I do ? Sorry for my English guys.
Instead of flashing an extracted radio image try to flash a normal shipped rom (if possible matching your cid). Capture the process using usb monitor to see where exactly it fails and which error you get.
Where can I download
pof said:
normal shipped rom (if possible matching my cid).
Click to expand...
Click to collapse
?
I had RADIO 1.05 , that I remember, and have a phone from T-Mobile - MDA Vario II.
Benone said:
Where can I download ?
I had RADIO 1.05 , that I remember, and have a phone from T-Mobile - MDA Vario II.
Click to expand...
Click to collapse
No rom matching your cid is available then, use the TyTN 1.18 rom.
pof said:
No rom matching your cid is available then, use the TyTN 1.18 rom.
Click to expand...
Click to collapse
I tried that ROM 2 times, once I plugged with holding camera button and second time without. I made monitor of QTEK rom aswell, because its the one which is changing phone screen from red green blue stripes to completly white. But nothing else is doin...
A attaching logs in zip file below. I have 3 files from each session, I dont know which are correct, 2 of them i saved and 1 is exported.
What do you think ?
I used USB-monitor from http://www.hhdsoftware.com/
very weird... usb seems not working but for what you say bootloader seems to be ok. Are you sure this was after patching the radio with universal unlocker? it seems totally a different problem :-$
I guess you'll have to wait until t-mob releases a ROM matching your CID and then flash it using the hermimg.nbh sd-card flashing method.
You can also try to connect to it via serial, I have no experience on that, but a search on these forums might tell you how...
keep us updated
How long I have to wait ?
Should I go to T-Mobile when I will be back to Scotland and tell them what I did or what ? Did I lose my warranty ? Do you know approximately how much they will charge me for flashing my phone ?
Do I really have no chances to repair it by myself ?
Benone said:
How long I have to wait ?
Click to expand...
Click to collapse
Until t-mobile releases a rom with your cid... it can be today or next year, I don't know.
Benone said:
Should I go to T-Mobile when I will be back to Scotland and tell them what I did or what ? Did I lose my warranty ? Do you know approximately how much they will charge me for flashing my phone ?
Click to expand...
Click to collapse
I don't think you lost the warranty. They usually charge about 100 eur for flashing it back in the service centre. They do it by inserting a diagnostics sd card, but we don't have it for the Hermes
Benone said:
Do I really have no chances to repair it by myself ?
Click to expand...
Click to collapse
You can try flashing over serial port, and you can try sd-card flashing, but for sd-card flashing you need a rom matching your CID first.
Eureka!!!
Finally I made my device working again!
And I dont have simlock !
After trying everything.... ufffff.
THX !!!!!!
1) I downloaded ftp://xda:[email protected]/Hermes/Tools_and_Programs/HTC_Hermes_SIM_Unlock_v1.zip
2) Reset my phone in bootloader mode.
3) Plug USB cable.
4) Run HTC_Hermes_SIM_Unlock_v1.
5) After 20 min. my phone said ELO to meeeee He did not have simlock when was saying that.
YE YE YE
That was simple. If you have any Hermes radio problem, try that first - HTC_Hermes_SIM_Unlock_v1.
Will be more often here, forum seems to be really interesting.
YO!
Yipie
Glad it worked
Hi Jiggs,
Really really need your help...
I've accidentally flashed my O2 atom life to a wrong rom, and it was recovered by a rom named AL1.DIO & ExRom.img which downloaded from xda FTP sites.
The rom was recovered,however for the warranty reason i need to flash back to O2 original firmware. And when try to flash to it I encountered "Wrong Customer ID", can you advise how to bypass the CID check and flash to original ROM?
I've tried on the post stated on http://forum.xda-developers.com/showthread.php?t=293632 but the screen didn't show anything after execute the .exe file.
I do not wish to unlock the CID just intend to bypass it, can you enlightened me?
Your help is greatly appreciated.....
First off sounds like you have some idea what you're doing? (bootloader working?)
Secondly there is no jiggs anymore, he's gone, retired, moved on!
Last but not least he left a torrent of info in the wiki http://wiki.xda-developers.com/index.php?pagename=HTC_Atom start here and read, you may find a solution! good luck bro!
homer285 said:
First off sounds like you have some idea what you're doing? (bootloader working?)
Secondly there is no jiggs anymore, he's gone, retired, moved on!
Last but not least he left a torrent of info in the wiki http://wiki.xda-developers.com/index.php?pagename=HTC_Atom start here and read, you may find a solution! good luck bro!
Click to expand...
Click to collapse
Hi bro,
Thanks for the quick reply.
I'm so sorry I'm a newbie didn't know bout Jiggs already retired
Btw I still manag boot into bootloader, the problem is due to the warranty reason, i need to dump my atom life back to its original state before i send in.
Now I'm still able to use the phone, it's just not in original rom.
Had tried to look around the thread you post to me, but i couldn't find any solution at all. Sigh, hope that someone can englighten me as i totally lost...
so you get the "CID error", whether you flash in bootloader or DSUU mode correct?
what is your bootloader version?(if not original Atom Life?)
<-and have you tried the EBOOT SDCard (this may not work for Atom Life) method to restore bootloader if not as stated above?
homer285 said:
so you get the "CID error", whether you flash in bootloader or DSUU mode correct?
what is your bootloader version?(if not original Atom Life?)
<-and have you tried the EBOOT SDCard (this may not work for Atom Life) method to restore bootloader if not as stated above?
Click to expand...
Click to collapse
Hi bro,
My boot loader version is H3 - v0.79.
try both either to flash the official O2 rom from bootloader or window both are encountered 'Error - Customer or Model ID error'
Still have any solution?
Many thanks at all...
Cheers!
kenzojoey:: don't worry. its v simple. first connect USB, enter boot loade, RUN ur Upgrade, after finishing extrect, last STEP "NEXT" to strat up grade, after clicking NEXT immediately press u,r Keybord "DOWN ROW" it will work. good luck
Hi I know its been asked for number of times but I can't find the correct answer for this.
I wish to upgrade my radio version to ATT latest radio (HERM_Radinly_1.54.07.00). I have it downloaded from wiki and trying to follow the instruction.
1. Extracted HERM_Radinly_1.54.07.00_CustomRUU.rar.
2. Disabled Active Sync.
3. Entered in Bootloader. Phone connected to machine. Its in USB mode now.
4. Now when I run RUUWrapper.exe, I get a screen where I have to make some selection. And here I need some help. There are following options,
a.SPL 1.01 MFG Bootloader
b.SPL 1.04/1.10 SPL 1.09 Bootloader
c.SPL 1.11/1.13/1/30/1.35/1.40 Bootloader
d.SPL 2.02/2.10 New Bootloader
b. Force Using SSPL
Check Box for Is HardSPL?
Now if some one can help me to find out correct option in the list, I can move further. My current SPL and IPL are in my signature. As far as I remember I have HardSPL done too.
Any help will be really appreciated.
Thanks -nbhor
nbhor said:
Hi I know its been asked for number of times but I can't find the correct answer for this.
I wish to upgrade my radio version to ATT latest radio (HERM_Radinly_1.54.07.00). I have it downloaded from wiki and trying to follow the instruction.
1. Extracted HERM_Radinly_1.54.07.00_CustomRUU.rar.
2. Disabled Active Sync.
3. Entered in Bootloader. Phone connected to machine. Its in USB mode now.
4. Now when I run RUUWrapper.exe, I get a screen where I have to make some selection. And here I need some help. There are following options,
a.SPL 1.01 MFG Bootloader
b.SPL 1.04/1.10 SPL 1.09 Bootloader
c.SPL 1.11/1.13/1/30/1.35/1.40 Bootloader
d.SPL 2.02/2.10 New Bootloader
b. Force Using SSPL
Check Box for Is HardSPL?
Now if some one can help me to find out correct option in the list, I can move further. My current SPL and IPL are in my signature. As far as I remember I have HardSPL done too.
Any help will be really appreciated.
Thanks -nbhor
Click to expand...
Click to collapse
You are right, this has been asked a number of time... . May i suggest another method to load your rom?: SD card. You do not need to use a USB connection (no risk to loose it) nor a PC and it works perfectly.
1> format a sdcard in FAT32 (use a card of max 2GB)
2> copy the .nbh file to it (Preferably the only file on the card)
3> rename the file: HERMIMG.NBH
4> insert the card and push: OK-POWER-SOFT RESET (to go to the 3 colors screen). It will detect your hermimg file (says "loading" in blue) and describe the content
5> follow instructions on screen.
And that's it ! Just note that flashing a radio rom is slow. This means that you will have the impression that it stops time to time. Just be patient
Oh... by the way, having tried nearly all radios available, 1.47 is for me the best compromize between battery drain and performances (at least in my area). But, once again, this is a matter of taste. Make your religion
Thanks a lot. Actually I have followed the same process while upgrading from WM5 to vp 3G's WM6. But I was not aware that I can use same process to upgrade the radio only. And to my surprise it worked like a charm. Appreciate your help in this matter. I will update you with my experience on this radio version.
Thanks -nbhor
Hi Guys,
I am having the usual radio issues atm, no version showing etc.
I have gone through the wiki and read the thread by POF on the issue and tried flashing a half a million times (ok maybe not but you know what I mean :-0)
So here is my issue now, I would love to try flasing via SD but mine just won't do it, doesn't even ask a damn thing once in bootloader, just sits there.
I am running 2.10.olipro loader and IPL 1.04, should this work for doing radio updates or any updates off the SD card? I can read it fine and copy dump to it from both PC and PDA and I have tried to working cards aswell. Any ideas?
Cheers Glenn
Ps I just noted that nbhor is running exactly what I am running and it worked ok for him - WTF?
terminatermule said:
Hi Guys,
I am having the usual radio issues atm, no version showing etc.
I have gone through the wiki and read the thread by POF on the issue and tried flashing a half a million times (ok maybe not but you know what I mean :-0)
So here is my issue now, I would love to try flasing via SD but mine just won't do it, doesn't even ask a damn thing once in bootloader, just sits there.
I am running 2.10.olipro loader and IPL 1.04, should this work for doing radio updates or any updates off the SD card? I can read it fine and copy dump to it from both PC and PDA and I have tried to working cards aswell. Any ideas?
Cheers Glenn
Ps I just noted that nbhor is running exactly what I am running and it worked ok for him - WTF?
Click to expand...
Click to collapse
As far as you can still flash, the method explained above should work
terminatermule said:
Hi Guys,
I am having the usual radio issues atm, no version showing etc.
I have gone through the wiki and read the thread by POF on the issue and tried flashing a half a million times (ok maybe not but you know what I mean :-0)
So here is my issue now, I would love to try flasing via SD but mine just won't do it, doesn't even ask a damn thing once in bootloader, just sits there.
I am running 2.10.olipro loader and IPL 1.04, should this work for doing radio updates or any updates off the SD card? I can read it fine and copy dump to it from both PC and PDA and I have tried to working cards aswell. Any ideas?
Cheers Glenn
Ps I just noted that nbhor is running exactly what I am running and it worked ok for him - WTF?
Click to expand...
Click to collapse
Hi Glenn this happened with me for couple of times too. Didn't ask anything in boot loader.Then I went back to board and did as this thread says http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing and this helped. May be this will help you too. All the best.
Thanks -nbhor
Hi nbhor,
Thanks for that, I had read that thread but not stressed much about preparing the cards, a format and error check (which ti my amazment found bad sectors on two brand new transflash cards sorted it and it now tries to flash but still fails unfortunately. Oh well looks like no radio for me again :-(
Cheers Glenn
So i wanted to flash my cingular 8125 to windows mobile 6, so i downloaded this:
(BIG MISTAKE)
http://www.tradebit.com/filedetail.php/2559279-Software-Programs-Cell-Phone-Programs
and i followed the instructions and after i hard reseted my phone, it booted to a white screen. I have tryed reflashing, going into bootloader mode and reflashing, and i nothing helps.
can one of the experts on this forum please help me???!!!
thanks
i need help assap!! lol
i dont care even if i flash back to winmo5, I JUST WANNA UNBRICK
dahdout said:
So i wanted to flash my cingular 8125 to windows mobile 6, so i downloaded this:
(BIG MISTAKE)
http://www.tradebit.com/filedetail.php/2559279-Software-Programs-Cell-Phone-Programs
and i followed the instructions and after i hard reseted my phone, it booted to a white screen. I have tryed reflashing, going into bootloader mode and reflashing, and i nothing helps.
can one of the experts on this forum please help me???!!!
thanks
i need help assap!! lol
i dont care even if i flash back to winmo5, I JUST WANNA UNBRICK
Click to expand...
Click to collapse
What IPL/SPL it displays now ? ,Does it get into Bootloaders ? if it still does than download and flash 'wizard_love_rom' hope it'll recover back.
RE:
It just boots into a white screen. If i hold the camera and power buttons together it boots into bootloader mode, and says USB in the bottom corner. (when i am conncected via usb) but the problem is that active sync doesnt recognize it in bootloader mode. I have tried flashing it in many different ways and i have had no success.
When i go home i will try wizard_love_rom.
and as for the IPL/SPL, i will also check that when i get home.
Where can i download the wizard_love_rom?
Thanks for the help !
RE:2
Hello,
Mr IPL and SPL are both 2.25.0001
My GSM: 02.25.11
My OS: 2.18.0.0
Good News
So, I flashed my phone with the "Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar"
which i found the download for over a quick google search, and now i want to update to winmo6 or 6.1.
Can you send me the link for the easiest way to do it on a G4 cingular 8125 (HTC Wizard.)
I have never CID unlocked, which was probably why i got the white screen earlier. but do i need to do it know that i am on the wizard love rom?
please help,
thanks
dahdout said:
So, I flashed my phone with the "Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar"
which i found the download for over a quick google search, and now i want to update to winmo6 or 6.1.
Can you send me the link for the easiest way to do it on a G4 cingular 8125 (HTC Wizard.)
I have never CID unlocked, which was probably why i got the white screen earlier. but do i need to do it know that i am on the wizard love rom?
please help,
thanks
Click to expand...
Click to collapse
Glade its working again !
You got a G4 device,it cannot be CID unlocked,but however,it can be upgraded to wm6 or 6.1,read the methods 'HardSPL' or 'SoftSPL' posted as stickies in the G4 forum for upgrading to wm6 or 6.1.
re:3
thanks, you really saved me with your help!
dahdout said:
thanks, you really saved me with your help!
Click to expand...
Click to collapse
Thanks !
Glade you got it working
sorry, but i need help... again
Ok,
I know that this may be getting a little annoying for you and im sorry for that, but i need your help on this. I am currently running the wizard love rom. And I have Hard SCP'd.
I have to problems:
1. My EDGE doesn't work, i only get GPRS speed data.
2. I can't upgrade to any new rom..... i always get "ERROR [300] Get a newer update utility!"
How can I fix both of these problems?
I have searched forums and google and nothing has come up.
dahdout said:
Ok,
I know that this may be getting a little annoying for you and im sorry for that, but i need your help on this. I am currently running the wizard love rom. And I have Hard SCP'd.
I have to problems:
1. My EDGE doesn't work, i only get GPRS speed data.
2. I can't upgrade to any new rom..... i always get "ERROR [300] Get a newer update utility!"
How can I fix both of these problems?
I have searched forums and google and nothing has come up.
Click to expand...
Click to collapse
ok,for error (300)you can use the RUU MUNS already posted in the 'HardSPL' thread,download the RUU_MUNS application extract it to a folder and copy and paste all the files of this extracted to the folder of the Rom replacing all the RUU files in that folder or copy the nk.nbf folder in the Rom to the extracted folder of the RUU_MUNS and then run the RUU,it will start to flash and complete and hopefully fully boot up.
For edge or gprs,you'll have to get network settings of your network carrier or check out the thread from where you downloaded the rom,its uaually posted there or check out the 'Network' thread.
Aquestion to Zabardast_1 ?
294 error , invalid vender ID
what does that means & asolution to it during rom update
ERROR [294] : INVALID VENDER ID
One of these error messages will appear when you use the wrong RUU to do the upgrade. RUU will check if the Model ID and Language ID are compatible with the device. Make sure you use the appropriate RUU tool to upgrade.