Hi. The phone application was not functioning well and the F/C dialog showed up. I powered off the phone and from that point, the phone won't turn on.
The battery was fully charged before this happened.
When I press the power button, the phone vibrates for half a second, the screen brightens up but does not show anything but a black screen.
I removed SIM and SD cards, removed the battery and performed the above steps but nothing happened.
I also tried to put on the charger to see what's going on. Once I plug the charger, the phone's screen brightens but shows only blank (even without pressing the power button)
When connected to the charger, the green light for charging is on for some minutes, then goes off automatically.
I tried to connect it to the PC, and PC Companion finds the device as usually. It even shows the dialog on the pc screen to mount the device.
I tried a hard reset, but does not work
On some point, the sony logo appeared and then a dialog saying: "sorry process system is not responding". The first time I pressed Force Close and the phone turned off. Immediately after that, the phone turned on and showed the exact message. I pressed "Wait" but nothing happened in the next 15 minutes.
I called Sony's support center and they suggested a software update. Did the process exactly as it should, but again, even after the software update the screen shows nothing but black. It is all the time brightened for some reason.
I tried to turn off the phone for some time by removing the battery, but as soon as I put the battery back on, the phone's screen brightens and stays that way forever.
The phone was functioning perfectly up until this issue. The only application I had installed apart from some games, was AWDLauncher. On the screen I had only a TASK widget and a battery status widget.
The phone is 3 months old and has been always in perfect condition.
ANY help would be appreciated!!!!
Many Thanks
Try to format phone with this method hope it should work as it seems the issue is with OS only ..
http://forum.xda-developers.com/showthread.php?t=717949
Many thanks for the prompt reply. I will try to do so and let you know how it goes!
o0k00l said:
Try to format phone with this method hope it should work as it seems the issue is with OS only ..
Click to expand...
Click to collapse
I tried the steps found in the link you gave me, but I couldn't go any further after step no (5) from the tutorial, as it would require to enable Debugging mode and I cannot access the OS (since the device won't turn on).
Is there a way to format all the contents of the device and have them replaced by running SEUS (as it always says that my device is up to date now)?
Was it this:
http://www.sonyericsson.com/cws/sup.../detailed/updateservice/xperiax10?cc=gb&lc=en
That Sony Ericsson told you to do?
If not, use that.
Download it, follow the steps when it says you have the latest version, press "Install Anyway".
Hope this works.
Hi itTim. thanks for the response
this is what i did but no improvement at all ((
Sounds like you broke your LCD screen somehow.
That would suck because I broke mine and it cost me $200 to fix.
Hi Hypercore.
Yes that could be the problem. The thing is that I always took rally good care of the phone, always carried in a leather pouch and never droped it. How sensitive is this lcd anyway?? Did you notice any cracks on your lcd or was the problem simillar to mine?
Thanks
When you turn on the phone does the lcd backlight turn on?
If so, look for any faint lines of color (usually a hairline size). If you see any of those then your screen is cracked.
the backlight is on, but there are no lines of colour on the lcd screen.
another weird thing is that the green light on the top blinks one or two times every time i put on the battery. even if the phone is off, once I insert the battery turns on automatically after a couple of seconds.
If all else fails you could try to flash back to your original fw with the tools here:
ht tp://forum.xda-developers.com/showthread.php?t=683793
AyDee said:
If all else fails you could try to flash back to your original fw with the tools here:
ht tp://forum.xda-developers.com/showthread.php?t=683793
Click to expand...
Click to collapse
That won't do anything.
I had almost the same issue. Nothing worked. But, when I removed the battery and left it for a day (24h) without it, it just started working again. Still working without issues..
Good luck!
Devtone said:
I had almost the same issue. Nothing worked. But, when I removed the battery and left it for a day (24h) without it, it just started working again. Still working without issues..
Good luck!
Click to expand...
Click to collapse
Phones are very wierd pieces of technology. I once bricked my k610i and that's a phone that's supposed to be impossible to un-brick, but out of nowhere a month or so later i picked it up, hit power and it turned on perfectly. Made no sense at all, but it worked.
Taking the battery out for a long time probably took all the electrical charges from it (kind of like how a computer power supply / monitor can hold power charges) and reset your handset.
Hypercore said:
Phones are very wierd pieces of technology. I once bricked my k610i and that's a phone that's supposed to be impossible to un-brick, but out of nowhere a month or so later i picked it up, hit power and it turned on perfectly. Made no sense at all, but it worked.
Taking the battery out for a long time probably took all the electrical charges from it (kind of like how a computer power supply / monitor can hold power charges) and reset your handset.
Click to expand...
Click to collapse
Indeed. It could be a frozen chip, memory fault, power-regulator and so on.
Hypercore said:
That won't do anything.
Click to expand...
Click to collapse
Ah, debug mode needed- I see now
tasaki said:
I tried the steps found in the link you gave me, but I couldn't go any further after step no (5) from the tutorial, as it would require to enable Debugging mode and I cannot access the OS (since the device won't turn on).
Is there a way to format all the contents of the device and have them replaced by running SEUS (as it always says that my device is up to date now)?
Click to expand...
Click to collapse
if you have done this and did not worked , then it is the LCD.
send it to workshop and check it there.
Guys i Really need the solve of this problem , my xperia has blank screen now without backlight and the phone completely doesn't work . when i put the battery and prees the switch botton it gives me 3 red signals , i've updated and hard reset but it didn't work , and btw the LCD is fine , any idea. did removing the battery worked???? . please answer
After a looooot of time since my latest post, finally my Xperia came back to life. There was a battery failure which means the phone was ok all the time. Weird thing is that the led light showed that the battery was charging ok. I removed the battery and after a lot of time it is working ok again. This was really really odd.
FYI for anyone else that gets this issue.
I just had this for the past hour after trying to change my baseband....could not get it back for anything.
What I did finally try was run another baseband via flash tool, connected to usb and it started flashing....after flash phone powered on again...yeah I agree with everyone, that is freaking scary when it happens.
Related
I hope this is the right sub-forum to open this thread if not please movie it.
Half an hour ago I Got the 9.4.2.15 firmware update from asus. after the update was applied my prime asked me if I want to turn it off....I approved and the device shut down and stayed off.I tried to turn it on and nothing happened.
When I applied the update I had more then 80% of the battery.
I plugged the phone to the charger and the charger light on the power button changed from orange to green
While the Prime was charging(and after it was fully charged) I tried to do some stuf
I tried to press the on button and nothing happened and no vibration.
I tried to hold the on button for about 30 seconds and the only thing that happened is that I got a vibration(the same you get when you turn on your device).
I tried to reset the device with the reset hole near the microsd with a needle and nothing happened.
I tried holding the power button and the volume button(once the up and the other time the down) and nothing happened except the vibration after about 10 seconds.
ANY IDEAS?
*my biggest problem is I purchased the Prime from "Amazon US" and I don't leave in the us...How If I need do I use my ASUS warranty.who do I connect?
Thanks.
Try draining the battery completely then charging it back up. Then try to boot it up again. You might have a glitch or bug. Its always good after an update is applied to let it update then it reboots itself. After it loads back up,go into home screen. Then **** down device and cut back on. This will eliminate anything happening from rogue codes.
http://service.asus.com/InfoPage.aspx?rid=7
Good luck
demandarin said:
Try draining the battery completely then charging it back up. Then try to boot it up again. You might have a glitch or bug. Its always good after an update is applied to let it update then it reboots itself. After it loads back up,go into home screen. Then **** down device and cut back on. This will eliminate anything happening from rogue codes.
Click to expand...
Click to collapse
Any Idea how do I drain the battery, The Prime has now 100% battery and I am unable to turn it on...the screen stays black?
jdbaker82 said:
http://service.asus.com/InfoPage.aspx?rid=7
Good luck
Click to expand...
Click to collapse
Thanks.
Any more ideas?
*By the way I have the option to take the prime to a shop that could fix it, I am sure the problem is a software bug and not hardware...Should I try doing this because ship it to asus ans back will take about 3-4 weeks.
Try a hard reset and if that doesnt work do a search for this (EP201_SDUPDATE.ZIP)
ohwell said:
Try a hard reset and if that doesnt work do a search for this (EP201_SDUPDATE.ZIP)
Click to expand...
Click to collapse
I am unable to do "Hard reset" because the device do doesn't start, after pressing the power button nothing happens the screen stays black. the onle response I get from the device is vibration(after I hold the power button for about 10-12 seconds).
I don't think that "EP201_SDUPDATE.ZI" will help because I don't have accesses to my bootloader
Did you happen to drop the device or bang it pretty hard? If so, could be a chance the connector to your display is loose and device is actually on but the screen is off. Best way to check this is to connect your prime to your t.v. thru HDMI. Then try to cut it on. If something displays on your t.v. but screen still won't cut on, then connector came loose from your display. That is the best way to check. Plus you could also operate tablet like that.
Nope,didn't drop or hit it.
Unfortunately I don't have HDMI cable that connects to the prime.
your idea is good but even without the cable I am sure it's not the problem...but lets say that it is the problem...then if the device is actually on I should be able the hear the sound it makes when I use the volume buttons and when I receive new emails...the thing is I am unable to produce any sound from the device.
I just applied my update and it didn't ask me if I wanted to power down, it did itself. Did you power down when it was starting to install?
My screen did say "power down" but I knew it would do it itself.
Maybe like doing a battery pull during a flash?
Sent from my Transformer Prime TF201 using xda premium
Maybe you are right and for some reason I turned the device off while it was in the middle of the update... so 5hat means as you said that I interupted the flash process...in this case the problem is the software of the device ...could I do somthing to fix it without going with it to a lab?
Sent from my Galaxy Nexus using Tapatalk
You might try inserting a pin or a paperclip into the reset hole next to the micro SD port.
PROBLEM SOLVED!!!
I decided to try and fix my prime one last time before I use the warranty. so I took a needle SMALLER one then I used the first time I tried to "Hard reset" the prime and inserted it into the hole near the microSD port....and this time I felt a "click"...I pressed for about 10 seconds and then released and the screen turned on
I immediately got the screen withe the open green robot and with a blue line under it that showed me that the update was applied....then the screen changed to the screen you get when you turn on the device(asus symbol and tegra3 symbol) and again I got a blue line showing me that the update is going on.
After the blue line went foreword to 100% it disappeared from the screen and I was left with the screen you get when you turn on the device(asus symbol and tegra3 symbol).
I have waited for about 20 minutes and nothing happened....I turned off the device with the power button and then turned it on again(this time the device responded after 1-2 seconds)...I got a vibration and the screen was on(asus symbol and tegra3 symbol). after a few seconds the screen changed to another screen( another ASUS symbol with a turning circle under it) after about 8 seconds my device was fully working all my data was present(didn't reset with the needle should have deleted everything?) and my software number was 9.4.2.15,so the update was fully applied.
I tried turning on and off the device for a few times and had no problems with it.
So basically the device is working and I have no idea what was the problem
The tip i got for everyone trying to reset the device with a needle/paper clip....YOU HAVE TO FEEL THE CLICK
that's awesome! Congrats!
These are expensive toys (in my case addiction).
Maybe it was a bad flash which can be really spooky if you're not rooted with a custom recovery.
Sent from my Transformer Prime TF201 using xda premium
Need some advice please
Any Flyer member who can advice me please?
Buyed a WIFI Flyer 16Gb Gingerbread stock no rooted turned on and suddenly turned off and got stuck in black screen (with some light in the back) vol down + power, nothing.
battery has 100% charge, but red led turned on and off ocasionally.
Any advice how to revive it would be greatly apreciated!
Thanks in advance,
Soft reset - Hold down power button only. Keep holding until tablet resets. You should know when this happens. You can't bring it up in bootloader/recovery (down vol. + power), until it's first actually turned off.
Does your PC recognize a device being plugged in when you connect
Sent from my HTC Flyer P510e using xda premium
.
Thanks for your replies:
It didnt work pressing only vol dow for a while, or presing only power button, it never rests.
Just behind power button a green mini led is turned on now all the time, probs started when removed back to insert sd card.
Tooked off to make some tests but now still nothing...
If connecting to PC nothing happens...not detected...no asking for install drivers
Any other advice?
Thanks in advance!
orb3000 said:
Thanks for your replies:
It didnt work pressing only vol dow for a while, or presing only power button, it never rests... probs started when removed back to insert sd card.
If connecting to PC nothing happens...not detected...no asking for install drivers
Any other advice?
Thanks in advance!
Click to expand...
Click to collapse
Take off back cover... Remove SD card... Try to reset again, power btn only, hold down 20 to 30 secs., don't use volume btn.
Nothing happens
i would suggest trying to globatron's attention. if anyone on this board would know what to do it would likely be him
orb3000 said:
Nothing happens
Click to expand...
Click to collapse
I would agree with mcord11758... Still...
orb3000 said:
battery has 100% charge, but red led turned on and off occasionally.
Click to expand...
Click to collapse
A red led isn't going to show with a 100% power condition. Later you wrote...
orb3000 said:
It didn't work pressing only vol down for a while, or pressing only power button, it never rests. Just behind power button a green mini led is turned on now all the time...
Click to expand...
Click to collapse
(doesn't make sense to me) A green led can't show unless the tablet is plugged into a power source and the battery actually is 100%...
If yours is a stock unit with a stock rom (and isn't defective), I would suspect a low battery condition that can't reset/reboot for lack of power...
Suggest you plug it into the wall and try the reset procedure again, and if still a failure, (maybe you can get some help from globatron or) call HTC.
...and then again, as I've read in other threads (that you've also seen), maybe all that's needed is a battery disconnect & reconnect. - Hope you get those pics, and if so... make it a last course of action, as you'll have no warranty if you do it.
Thanks.
Update:
I left computer connected to Flyer all night, and the day after it was turned off, then unplugged from PC and plugged it again, PC recognized the tablet and after that I ran the stock RUU, now it´s stuck on the process as it has been more than 20 minutes and progress bar in computer is at 100% with the following legend:
sending..........
updating the Rom image on your android phone
It is stuck there, how much should I wait? or if you recommend to do something else?
Thanks in advance for all your help.
UPDATE: RUU failed, says I have the wrong image, finished, exited and rebooted normally!
Now working, but I´m afraid to open the cover to insert my sd as the last time it was when it was turned off
Orb,
That sounds like it when into DL mode. On the flyer once you get out of DL mode it's normally fine after that. It seems to be random, mine did it once or twice, leedroid has seen it as have a few others.
After it boots again it goes back to normal.
Hi mate,
Thanks for your reply.
Very strange behavior. After all above mentioned I was able to use is perfect, even updated to OTA Honeycomb all went ok, installed some apps, etc.
Then decided it was time to test again to remove the cover and install my sd card, just in the minute I touched the back , not even finished of removing, and Flyer went screen off, now again I can´t turn it on. Could be a short circuit or something?
I will leave it connected to wall charger for the night and hopefully tomorrw will be able to turn it on again....
I swear never again to remove the back cover
PS: I checked battery level before all this and it was in 77%, now red led on power button is on...
globatron said:
Orb,
That sounds like it when into DL mode. On the flyer once you get out of DL mode it's normally fine after that. It seems to be random, mine did it once or twice, leedroid has seen it as have a few others.
After it boots again it goes back to normal.
Click to expand...
Click to collapse
orb3000 said:
Hi mate,
Thanks for your reply.
Very strange behavior. After all above mentioned I was able to use is perfect, even updated to OTA Honeycomb all went ok, installed some apps, etc.
Then decided it was time to test again to remove the cover and install my sd card, just in the minute I touched the back , not even finished of removing, and Flyer went screen off, now again I can´t turn it on. Could be a short circuit or something?
I will leave it connected to wall charger for the night and hopefully tomorrw will be able to turn it on again....
I swear never again to remove the back cover
PS: I checked battery level before all this and it was in 77%, now red led on power button is on...
Click to expand...
Click to collapse
That's weird, if it's not too much could you try and get a logcat (adb logcat) when its screen goes off while opening the cover. That should help us establish whether this is a HW problem(unique perhaps bad mainboard) or software problem (me,globatron,Lee, etc. experienced)
I can also confirm that it happened to me too couple of months back, but after soft reset it rebooted fine, but the backcover issue is new.
Sent from my HTC Flyer P510e using XDA Premium HD app
hello
Im orbs friend, my htc flyer still having the prob, everytime i touch the cover or pusih it by accident it goes back.
What I do is leaving it charging for awhile and press power button and vol down at the same time for around 30 sec for a couple of times and then it re start. Im guessing its not a software problem i dont find an explanation i even updated it to 2.3.4.
Device Xperia X10i, Unlocked Boot Loader, Rooted, Installed Jelly bean Rom of Feralab. Device worked perfectly on it. Since yesterday, after waking up, found my device bricked. Symptoms displayed after device got bricked :
a) If connected to wall charger with battery present, device only displays green light for 15 to 20 seconds max and then green light goes off. Then no activity in the whole device.
b) If connected to wall charger with battery absent, device again shows green light (with battery absent that is).
c) Tried SEUS, Answer : After the complete successful operation : Nada Nothing !
d) Tried Flash Tool, Still Nada. Tried flashing Xperia Stock Rom : Replaced System.sin , Header.sin and what not etc. "Even checked No Final Matchup" while flashing. Answer : Nada. !
e) Stock Used is "X10i_3.0.1.G.0.75_CUST-IN_GENERIC_1237-0692.ftf" flashed it. Still Nada ! However, no errors occurred while flashing.
f) Device when trying to switch on, displays green light blinked once, then vibrates and then just goes simply Naaadaa !!!
Nothing at all. Please help. If this helps, I am attaching log file of flashing device via flash tool. Man, device is just bricked. Answer and help appreciated . Thanks in advance.
Since I can't attach link to external log file on paste bin : here's I have uploaded the log file.
Update : Since I was on Fera Lab's Jb earlier, I want to notify that my "Unknown Sources and Debugging" was not checked in phone settings. It wasn't on and now that its bricked, I dunno whether it will make any difference or not ? In bricked state, with "Unknown Sources and Debugging" not checked. Can't get device to on, blinks one time green signal and then vibrates and nothing afterwards !
Update Number 2 : Hey, after completely keeping aside the battery for more than 24 hours, I connected the device to external wall DC supply (while battery was removed and never inserted after the 24 hours interval that is). After connecting the device to DC wall supply, it gave me the same response, flicked and showed green light and then vibrated and then nothing ! F1 anyone. !!!
Update Number 3 : http://talk.sonymobile.com/t5/Xperi...on-Flash-mode-even-when-plugin-to/td-p/273134
Just Googled my problem and came to this link. I can very much relate to the link although, His device was water locked, (there was this small white rectangle, if it is water damaged then it will be red) Surprisingly, his device which was water damaged shows the same symptom as mine. So, i checked mine, but the sticker or white rectangle for moist / humidity checker is white totally. So I guess it can't be water damaged, although, it showed the same symptoms !
Update Number 4: Since green Light was always On, I thought what if its in flash mode and much to my surprise, the device is in Flash Mode when I switch it on, how I found out : While flashing via SEUS, I didnt press the back key and the device got connected in flash mode by default, So i narrowed down the problem to something that : My device boots to Flash mode and not as it normally should ? Is it a mother board problem ? Can it be cured ? (god no please not mother board problem) So ? Any thoughts anyone to make it come out f the flash mode. ?
C] Tried SEUS, Answer : After the complete successful operation : Nada Nothing !
after the Successful Operation did you unplug the phone and tried to turn it on?
After the Successful SE Update Services was successful my phone didn't start, then i removed battery and reconnected, power on and works fine.
search in forums for Dr Goodvibes his suggestions did help me.
ronaksworld said:
C] Tried SEUS, Answer : After the complete successful operation : Nada Nothing !
after the Successful Operation did you unplug the phone and tried to turn it on?
After the Successful SE Update Services was successful my phone didn't start, then i removed battery and reconnected, power on and works fine.
search in forums for Dr Goodvibes his suggestions did help me.
Click to expand...
Click to collapse
well thanks. at least some one replied. can you direct me to a specific url u have in mind regarding my query. also i have updated the query, kindly see the update. as for SEUS update Yes why indeed, i did that. Sorry, nothing came up. thanks for the reply though. gives me hope.
Message this guy Dr Goodvibes http://forum.xda-developers.com/member.php?u=4375132
katctv Lord
ronaksworld said:
Message this guy Dr Goodvibes http://forum.xda-developers.com/member.php?u=4375132
Click to expand...
Click to collapse
thanks. will do.
asciisort said:
Device Xperia X10i, Locked Boot Loader, Rooted, Installed Jelly bean Rom of Feralab. Device worked perfectly on it. Since yesterday, after waking up, found my device bricked. Symptoms displayed after device got bricked :
Click to expand...
Click to collapse
Your phone indicates an unlocked bootloader, just for your information.
What's the thoughts on the battery? Was it in a good service state?
Take the battery out of the phone for 48 hours and then put it back in the phone and power the phone on.
The green light for a few seconds indicates the phone is attempting, or in a recovery state.
Your phone may have just had a 'moment' and has a "locked instruction", that just needs to be cleared with no power applied to the chipset.
This has worked for others and is more voodoo than science, but worth a try.
Dr Goodvibes said:
Your phone indicates an unlocked bootloader, just for your information.
What's the thoughts on the battery? Was it in a good service state?
Take the battery out of the phone for 48 hours and then put it back in the phone and power the phone on.
The green light for a few seconds indicates the phone is attempting, or in a recovery state.
Your phone may have just had a 'moment' and has a "locked instruction", that just needs to be cleared with no power applied to the chipset.
This has worked for others and is more voodoo than science, but worth a try.
Click to expand...
Click to collapse
Oh thanks for the update about the boot loader state. i definitely be keeping it apart for 48 hours and will update you regarding the same. thanks for the reply, you know i love this set of mine and your precious replies gives me hope.
Regarding the battery state, i guess it was okay, gave me a 1 day backup on the phone. So i guess it was in a kinda okay service state. though am not sure whether its fully charged or not. i don't actually know the power state / current charge level of the battery though coz i found the device bricked. if there's anything you can suggest, will be really helpful. though thanks for the information.
So I waited and waited for some more time, couldn't wait any longer for the 48 hours duration. Does t has to be 2 days ? I just wanted to bring my device back to life. Though, after giving up shortly after 12 + hours, I flashed it again, it did successfully, although, nothing even now, green light followed by a vibration and then boom. nothing ! f1 help needed ? btw, does it has to be 2 days?
I would have placed the battery back in the phone and pressed the power button and see if it booted, or allowed you to get to CWM Recovery with blue light or xRecovery(if installed).
One day, one week. How long does residual power remain in a circuit board to hold the current date/time before resetting?
Maybe buy a cheap BST-41 1500mAh battery for the XPERIA X10 and try that. Could be just a bad battery.
You could check the battery with a multimeter and see if it still has a charge.
My knowledge base stops at this point as I have no experience beyond this.
Good luck.
Dr Goodvibes said:
I would have placed the battery back in the phone and pressed the power button and see if it booted, or allowed you to get to CWM Recovery with blue light or xRecovery(if installed).
One day, one week. How long does residual power remain in a circuit board to hold the current date/time before resetting?
Maybe buy a cheap BST-41 1500mAh battery for the XPERIA X10 and try that. Could be just a bad battery.
You could check the battery with a multimeter and see if it still has a charge.
My knowledge base stops at this point as I have no experience beyond this.
Good luck.
Click to expand...
Click to collapse
Thanks Dr. Goodvibes, I definitely will keep you posted. Though, when I plugged the battery in, first I did check, nuthing ! green light + vibration. and then it goes blank. I installed my feralab jb rom via xRecovery so, yes it is there (installed) but afterwards I have flashed the stock via SEUS so i guess even xRecovery is gone now. I am not for sure. Though it was installed earlier. Right now I am thinking of keeping it apart till the time i found a new battery, it can be even 2 + days. Even 1 week. I will wait for a week now. Thanks for letting me know all about this. Keep me posted.
Dr Goodvibes said:
Your phone indicates an unlocked bootloader, just for your information.
What's the thoughts on the battery? Was it in a good service state?
Take the battery out of the phone for 48 hours and then put it back in the phone and power the phone on.
The green light for a few seconds indicates the phone is attempting, or in a recovery state.
Your phone may have just had a 'moment' and has a "locked instruction", that just needs to be cleared with no power applied to the chipset.
This has worked for others and is more voodoo than science, but worth a try.
Click to expand...
Click to collapse
Update Number 2 : Hey, after completely keeping aside the battery for more than 24 hours, I connected the device to external wall DC supply (while battery was removed and never inserted after the 24 hours interval that is). After connecting the device to DC wall supply, it gave me the same response, flicked and showed green light and then vibrated and then nothing ! F1 !!!
Dr Goodvibes said:
Your phone indicates an unlocked bootloader, just for your information.
What's the thoughts on the battery? Was it in a good service state?
Take the battery out of the phone for 48 hours and then put it back in the phone and power the phone on.
The green light for a few seconds indicates the phone is attempting, or in a recovery state.
Your phone may have just had a 'moment' and has a "locked instruction", that just needs to be cleared with no power applied to the chipset.
This has worked for others and is more voodoo than science, but worth a try.
Click to expand...
Click to collapse
Update 3: http://talk.sonymobile.com/t5/Xperi...on-Flash-mode-even-when-plugin-to/td-p/273134
Just Googled my problem and came to this link. I can very much relate to the link although, His device was water locked, (there was this small white rectangle, if it is water damaged then it will be red) Surprisingly, his device which was water damaged shows the same symptom as mine. So, i checked mine, but the sticker or white rectangle for moist / humidity checker is white totally. So I guess it can't be water damaged, although, it showed the same symptoms !
Dr Goodvibes said:
I would have placed the battery back in the phone and pressed the power button and see if it booted, or allowed you to get to CWM Recovery with blue light or xRecovery(if installed).
One day, one week. How long does residual power remain in a circuit board to hold the current date/time before resetting?
Maybe buy a cheap BST-41 1500mAh battery for the XPERIA X10 and try that. Could be just a bad battery.
You could check the battery with a multimeter and see if it still has a charge.
My knowledge base stops at this point as I have no experience beyond this.
Good luck.
Click to expand...
Click to collapse
Update Number 4: Since green Light was always On, I thought what if its in flash mode and much to my surprise, the device is in Flash Mode when I switch it on, how I found out : While flashing via SEUS, I didnt press the back key and the device got connected in flash mode by default, So i narrowed down the problem to something that : My device boots to Flash mode and not as it normally should ? Is it a mother board problem ? Can it be cured ? (god no please not mother board problem) So ? Any thoughts anyone to make it come out f the flash mode. ?
So I have a STOCK (no nothing) Verizon Galaxy S4 that is/was up to date as of 6/23/14. I think the last OTA push was a month or so ago.
A few days ago the device rebooted on its own a few times and I had no clue what was going on, but it stabilized for a day or so. Then yesterday it shut off and would not turn back on - the battery level was at least 80%. I removed the battery and reinserted it. I did not press the power button, but the device vibrates and displays the initial boot screen for about 3 seconds before it powers back off. At least I assume it is powered off - the screen goes black and there is no sign of life. The buttons do nothing to stir its slumber. I can remove and reinsert the battery for the same results.
I've tried POWER+HOME+VOLUME UP once inserting the battery - the blue text appears at the top but again the device shuts off after about 3 seconds.
Charger plugged in shows no light. However, when plugged in, the top part of the device does becomes warm on the screen and on the back with the cover off. - It actually becomes quite warm so I removed the battery but kept it plugged in just to test and it remained very warm. Unplugged now. Also it appears that inserting the battery does nothing now - maybe it's drained.
I'm pretty certain it's a hardware problem at this point, but I have no clue where to start. Has anyone ever had this issue or come across someone that has? I can take the device apart - does anyone know where and what I should be looking for as far as a loose connection or damaged component goes? Is there an electrical component diagram out there somewhere?
Any help is much appreciated!!
Have you tried getting into download mode at all?! I know you say that it won't go into stock recovery... But if somehow it got bricked then recovery corrupt be borked as well. Least if you can get into download mode you could try a no wipe image....
Also could just be hardware related in such case I don't have experience with that so much..
Sent from my SCH-I545 using Tapatalk
Mistertac said:
Have you tried getting into download mode at all?!
Click to expand...
Click to collapse
Yes. Same deal - it comes up for about 3 seconds... Must be a hardware issue.
tloth01 said:
So I have a STOCK (no nothing) Verizon Galaxy S4 that is/was up to date as of 6/23/14. I think the last OTA push was a month or so ago.
A few days ago the device rebooted on its own a few times and I had no clue what was going on, but it stabilized for a day or so. Then yesterday it shut off and would not turn back on - the battery level was at least 80%. I removed the battery and reinserted it. I did not press the power button, but the device vibrates and displays the initial boot screen for about 3 seconds before it powers back off. At least I assume it is powered off - the screen goes black and there is no sign of life. The buttons do nothing to stir its slumber. I can remove and reinsert the battery for the same results.
I've tried POWER+HOME+VOLUME UP once inserting the battery - the blue text appears at the top but again the device shuts off after about 3 seconds.
Charger plugged in shows no light. However, when plugged in, the top part of the device does becomes warm on the screen and on the back with the cover off. - It actually becomes quite warm so I removed the battery but kept it plugged in just to test and it remained very warm. Unplugged now. Also it appears that inserting the battery does nothing now - maybe it's drained.
I'm pretty certain it's a hardware problem at this point, but I have no clue where to start. Has anyone ever had this issue or come across someone that has? I can take the device apart - does anyone know where and what I should be looking for as far as a loose connection or damaged component goes? Is there an electrical component diagram out there somewhere?
Any help is much appreciated!!
Click to expand...
Click to collapse
If this is 100% stock phone u are looking at hardware issue of some type...
sent via safestrap 3.72 and echo v25.1! !
decaturbob said:
If this is 100% stock phone u are looking at hardware issue of some type...
Click to expand...
Click to collapse
It is and I agree. Just hoping someone on here might've seen this before and know how to fix it. I may try replacing the charging port hardware to see if that solves it.
amazon com/gp/product/B00EZ6LQ76/ref=ox_sc_act_title_1?ie=UTF8&psc=1&smid=A2N7MOLQT42QNO
tloth01 said:
I've tried POWER+HOME+VOLUME UP once inserting the battery - the blue text appears at the top but again the device shuts off after about 3 seconds.
Click to expand...
Click to collapse
To boot into recovery you only need to hold the VOL UP+POWER. Once the phone vibrates let go of power but keep holding the up button. I let go once the blue text appears for about 2 seconds.
ckarrow2 said:
To boot into recovery you only need to hold the VOL UP+POWER. Once the phone vibrates let go of power but keep holding the up button. I let go once the blue text appears for about 2 seconds.
Click to expand...
Click to collapse
Thanks... but then it turns off after that 3rd second...
If you can't get into download mode only option left is jtag
If you don't have a warranty there are places that will jtag it. I would recommend using someone that has done it before but I would be happy to try if you want to send it to me. I have the equipment but have yet to use it. I had a hard brick and thought I was going to have to try and Jtag mine but the warranty company decided they would go ahead and replace it. Like any place else, there would be no guarantee it will work. Of course if it is a hardware issue, jtag wouldn't work.
Some repair places will test it for free. I took one in for a sound problem and wanted to check out the loud speaker. The loud speaker was fine and they didn't charge me anything.
Tulsadiver said:
If you don't have a warranty there are places that will jtag it. I would recommend using someone that has done it before but I would be happy to try if you want to send it to me. I have the equipment but have yet to use it. I had a hard brick and thought I was going to have to try and Jtag mine but the warranty company decided they would go ahead and replace it. Like any place else, there would be no guarantee it will work. Of course if it is a hardware issue, jtag wouldn't work.
Some repair places will test it for free. I took one in for a sound problem and wanted to check out the loud speaker. The loud speaker was fine and they didn't charge me anything.
Click to expand...
Click to collapse
Okay thanks! Yea, I'll see if I can figure out if it's a hardware problem or not. If not, then I may take you up on your offer.
Hello, friends
Out of the blue, my S6 Edge tried to restart, but got stuck in a loop at the Samsung Logo. One or two times it went to "insert pin" and then restarted again. I tried to Force Restart and it didn't solve the problem.
After a few tries, I managed to wipe the cache partition. Now it's simply bricked with a black screen and a Solid White LED. I can't restart it, enter download mode or safe mode or anything. Odin doesn't recognize it at all. Is there anything I could try?
The phone is not rooted.
nclsamy310 said:
Hello, friends
Out of the blue, my S6 Edge tried to restart, but got stuck in a loop at the Samsung Logo. One or two times it went to "insert pin" and then restarted again. I tried to Force Restart and it didn't solve the problem.
After a few tries, I managed to wipe the cache partition. Now it's simply bricked with a black screen and a Solid White LED. I can't restart it, enter download mode or safe mode or anything. Odin doesn't recognize it at all. Is there anything I could try?
The phone is not rooted.
Click to expand...
Click to collapse
Hold only vol down + power for 20 seconds. Does the screen go off? Its not bricked otherwise you wouldnt even have the led lit. Theres hope
callumbr1 said:
Hold only vol down + power for 20 seconds. Does the screen go off? Its not bricked otherwise you wouldnt even have the led lit. Theres hope
Click to expand...
Click to collapse
Thank you! Tried it. Doesn't work. It's beyond my understading why would it behave this way after I managed to clear the cache. At least before that it went into download mode or safe mode. I still suspect a software issue.
nclsamy310 said:
Thank you! Tried it. Doesn't work. It's beyond my understading why would it behave this way after I managed to clear the cache. At least before that it went into download mode or safe mode. I still suspect a software issue.
Click to expand...
Click to collapse
So vol down + home + power will not get you to download mode?
How about recovery? Vol up + home + power?
This happened to me before and the way i got out of it was hold only vol down + power as soon as the screen went off completely (no led lit) switch to download mode combo.
Tried both of the commands. They didn't work. I will let it drain the battery completely and then see what happens.
nclsamy310 said:
Tried both of the commands. They didn't work. I will let it drain the battery completely and then see what happens.
Click to expand...
Click to collapse
Keep me posted
nclsamy310 said:
Tried both of the commands. They didn't work. I will let it drain the battery completely and then see what happens.
Click to expand...
Click to collapse
reminds me of the bad emmc memory like the note 4s had.
some times completly letting the battery drain can fix it being "stuck". then recharge for 20 min or so then trying to turn on.
if u plug it into pc does it reconize anything in device manager
even unknown device or descriptor failed anythiing at all?
This morning the LED was off, so I tried to recharge it. Nothing happens. Also, the PC doesn't detect it at all. I think it's safe to assume I need a new phone. Too bad...at least if I was able to recover the data on this.
nclsamy310 said:
This morning the LED was off, so I tried to recharge it. Nothing happens. Also, the PC doesn't detect it at all. I think it's safe to assume I need a new phone. Too bad...at least if I was able to recover the data on this.
Click to expand...
Click to collapse
you can thank sammy for no ext sd card for that one or more than likely pics would be on sd
now one last sollution is to try buying a cheap battery my note 5 had a issue it shut of one day and wouldnt do nothing i understand ures was blinkik and trying at least
so its a leap but last resort
same problem here started over a week ago - samsung S6: black screen, constant white led. tried all variations of resetting with buttons. over a year ago i replaced the battery, and its been fine since. when this no boot issued happened i also tried changing the battery to a known good one. on inserting a battery and then pressing the power button the indicator led will go to green for less than a second before changing to constant white, and it stays that way no matter what until the battery is drained or the battery is removed. Strange thing is there is no information from samsung on what this behaviour means, but I've come across dozens of other S6 owners on the web with the same problem, so this is obviously diagnostic behaviour designed by samsung - but no info from samsung. the phone has never been damaged or watered or rooted so I'm at a loss.
Confirmed diagnostics:
The phone will respond to the power button and attempt to turn on
The phone will charge a battery, so the charging circuits and battery circuits are working.
The phone does not get picked up by a Windows 10 PC with Kies installed in any state - other samsung phones get picked up no problem.
Same here
I have the same symptoms. When I hild the vol up+home+pwr I get a green let for 1/2 sec then white. No other combinations do a thing. I swapped the battery for a new one. No luck.
Mine started a few days ago. The phone was 50% charge and i plugged it in for two hours. Came back and it had a solid red led. After a few hours the red light went off. It was then 100% unresponsive. I then took it apart and disconnected the battery. When I reconnected it, it started to do the white let thing described above
athcliath said:
same problem here started over a week ago - samsung S6: black screen, constant white led. tried all variations of resetting with buttons. over a year ago i replaced the battery, and its been fine since. when this no boot issued happened i also tried changing the battery to a known good one. on inserting a battery and then pressing the power button the indicator led will go to green for less than a second before changing to constant white, and it stays that way no matter what until the battery is drained or the battery is removed. Strange thing is there is no information from samsung on what this behaviour means, but I've come across dozens of other S6 owners on the web with the same problem, so this is obviously diagnostic behaviour designed by samsung - but no info from samsung. the phone has never been damaged or watered or rooted so I'm at a loss.
Confirmed diagnostics:
The phone will respond to the power button and attempt to turn on
The phone will charge a battery, so the charging circuits and battery circuits are working.
The phone does not get picked up by a Windows 10 PC with Kies installed in any state - other samsung phones get picked up no problem.
Click to expand...
Click to collapse
I have one that behaves exactly the same I changed the battery and didn't make any difference. my next step is to replace power management chip. I'll let you know.
Any luck on this?
Mine has been like this for a couple months, kind of gave up on it, but decided to give it a go again!
Same problem here, just happend after switching the battery. Anyone have solved this?
I found a kinda solution, plug your charger in and charge past 30% then unplug charger. then use just vol down and power button for 7-10 seconds, after 7-10 seconds just release the power button while still holding vol down button until you see samsung logo, you can tell if you did it wrong by the solid led being back on, repeat until success, once you have it on do NOT press the power button or it will RESET back to solid led/black screen.
I have the same problem with my s6 active and similar story to dbeeheim. Has anyone fixed this? And can anyone confirm that enzo13's solution works?
Much thanks in advance!!
i have same problem!
Suddenly my S6 dead, battery was ~80%, no charge
yesterday i try to change battery, after that if push power button, LED small light comes but in white with purple, then stuck. (it's small Notifications LED)
and i chnge the screen, but no more than white/prople LED.
(no any thing on screen, always black..)
what is the problem?
i think it's battery because it last month didn't work good, and it's old 3years battery.. but no idea..
Hello guys my Samsung S6 sm-g920f has the solid white led and black screen. Really no fixes?
thank you
Same issue
I have the exact same issue. My Galaxy S6 Edge (G925F) suddenly died and won't get past the 'Galaxy S6 Edge Powered by Android' screen.
I am unable to reach the recovery options. I've tried flashing two different stock ROMs with Odin which succeed but without successfully turning on my phone. I've also tried flashing TWRP with success in Odin but it won't get past the 'Powered by Android' screen before turning off after +-4 seconds. The white LED is on even when the screen is black.
Just had this same issue, my battery died and I forgot to charge my phone overnight, woke up and it would not turn on, black screen. I did manage to replace the battery and do several diagnostic tests on it. My battery was receiving about half the power output it should be (this is normal it's a 4.5yo phone) and when I replaced the battery with a new one, it did not turn on. With wireless charging I can tell I am receiving a charge and with standard I can not. The screen does not indicate it is charging with either method but my wireless charging pad lights up indicating my phone is being charged. I think it may be the processor or screen itself. This really sucks because I lost all my data on my phone and data recovery can be over $500